Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “function unit testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

CSI Flight Computer System and experimental test results

This paper describes the CSI Computer System (CCS) and the experimental tests performed to validate its functionality. This system is comprised of two major components: the space flight qualified Excitation and Damping Subsystem (EDS) which performs controls calculations; and the Remote Interface Unit (RIU) which is used for data acquisition, transmission, and filtering. The flight-like RIU is the interface between the EDS and the sensors and actuators positioned on the particular structure under control. The EDS and RIU communicate over the MIL-STD-1553B, a space flight qualified bus. To test the CCS under realistic conditions, it was connected to the Phase-0 CSI Evolutionary Model (CEM) at NASA Langley Research Center. The following schematic shows how the CCS is connected to the CEM. Various tests were performed which validated the ability of the system to perform control/structures experiments.

Sparks, Dean W., Jr.↗
NASA NTRS1983

Effects of flow separation and cove leakage on pressure and heat-transfer distributions along a wing-cove-elevon configuration at Mach 6.9

External and internal pressure and cold-wall heating-rate distributions were obtained in hypersonic flow on a full-scale heat-sink representation of the space shuttle orbiter wing-elevon-cove configuration in an effort to define effects of flow separation on cove aerothermal environment as a function of cove seal leak area, ramp angle, and free-stream unit Reynolds number. Average free-stream Mach number from all tests was 6.9; average total temperature from all tests was 3360 R; free-stream dynamic pressure ranged from about 2 to 9 psi; and wing angle of attack was 5 deg (flow compression). For transitional and turbulent flow separation, increasing cove leakage progressively increased heating rates in the cove. When ingested mass flow was sufficient to force large reductions in extent of separation, increasing cove leakage reduced heating rates in the cove to those for laminar attached flow. Cove heating-rate distributions calculated with a method that assumed laminar developing channel flow agreed with experimentally obtained distributions within root-mean-square differences that varied between 11 and 36 percent where cove walls were parallel for leak areas of 50 and 100 percent.

Deveikis, W. D.↗
NASA NTRS2009

Sheet Membrane Spacesuit Water Membrane Evaporator Thermal Test

For future lunar extravehicular activities (EVA), one method under consideration for rejecting crew and electronics heat involves evaporating water through a hydrophobic, porous Teflon(Registered Trademark) membrane. A Spacesuit Water Membrane Evaporator (SWME) prototype using this membrane was successfully tested by Ungar and Thomas (2001) with predicted performance matching test data well. The above referenced work laid the foundation for the design of a compact sheet membrane SWME development unit for use in the Constellation System Spacesuit Element Portable Life Support System (Vogel and et. al., ICES 2008). Major design objectives included minimizing mass, volume, and manufacturing complexity while rejecting a minimum of 810 watts of heat from water flowing through the SWME at 91 kg/hr with an inlet temperature of 291K. The design meeting these objectives consisted of three concentric cylindrical water channels interlaced with four water vapor channels. Two units were manufactured for the purpose of investigating manufacturing techniques and performing thermal testing. The extensive thermal test measured SWME heat rejection as a function of water inlet temperatures, water flow-rates, water absolute pressures, water impurities, and water vapor back-pressures. This paper presents the test results and subsequent analysis, which includes a comparison of SWME heat rejection measurements to pretest predictions. In addition, test measurements were taken such that an analysis of the commercial-off-the-shelf vapor pressure control valve could be performed.

Trevino, Luis A.↗
NASA NTRS2022

Gas Trap Plug Design, Function and Performance

The cooling loops of the Internal Active Thermal Control System (IATCS) on the Node 3, Node 2 and US Laboratory (USL) Modules of the International Space Station (ISS) have been serviced by Gas Traps (GTs) since the onset of operations. These traps serve to protect the pumping function of the cooling loops by eliminating free gas that would otherwise impact the impellers and cause a loop shutdown. Gas Trap Plug Assemblies (GTPAs) have been designed, manufactured and tested, to permit function of the IATCS in the event of a loss of cabin atmosphere and long term decrew event. The GTPA also serve to give the crew additional time to evacuate the United States Operating Segment (USOS) in the unlikely event of an Ammonia breach of an Interface Heat Exchanger (IFHX). These GTPAs have been installed on the ISS IATCS since May 2019. This paper will address purpose, design and testing of the GTPA. The paper will also provide analyses showing residual trapping capability and free gas elimination of the GTs even while tightly plugged, for both the GTs and the Alternate Gas Trap Assemblies (AGTAs) ground spares.

Gas Trap Plugs↗
NASA NTRSDate not supplied

Statistical Engineering Toward Commercial Supersonic Flight: NASA's Quesst Mission

NASA’s Quesst Mission has dual goals of demonstrating low-noise supersonic technology in flight and surveying public reactions to low-noise supersonic overflight. For half a century, commercial aircraft have been required to fly slower than the speed of sound over land to prevent “creating an unacceptable situation” on the ground due to sonic booms. However, aircraft shaping techniques honed through decades of research have dramatically changed the way shockwaves from supersonic flight merge together as they travel to the ground. What used to sound like a boom on the ground will be transformed into a thump. NASA is now building a full-scale, piloted demonstration aircraft called the X-59 to demonstrate low-noise supersonic flight. In 2024, the X-59 aircraft will commence a national series of community overflight surveys to collect data on how people perceive “sonic thumps.” The results will be provided to national and international noise regulators as they consider creating new standards that allow commercial supersonic flight over land at acceptably low noise levels. In this presentation we provide historical context for the current prohibitions on supersonic commercial flight. Using data collected during earlier NASA tests, we demonstrate how generalized linear mixed models can be used to inform the functional dose-response curve. We also illustrate simulation experiments of the variability of sonic thump exposure across the United States. Finally, we discuss some of the challenges in designing the future community studies and generalizing them to a nationally-representative dose-response curve.

Quesst↗
NASA NTRS1997

Bone formation by three-dimensional stromal osteoblast culture in biodegradable polymer scaffolds

Bone formation was investigated in vitro by culturing stromal osteoblasts in three-dimensional (3-D), biodegradable poly(DL-lactic-co-glycolic acid) foams. Three polymer foam pore sizes, ranging from 150-300, 300-500, and 500-710 microns, and two different cell seeding densities, 6.83 x 10(5) cells/cm2 and 22.1 x 10(5) cells/cm2, were examined over a 56-day culture period. The polymer foams supported the proliferation of seeded osteoblasts as well as their differentiated function, as demonstrated by high alkaline phosphatase activity and deposition of a mineralized matrix by the cells. Cell number, alkaline phosphatase activity, and mineral deposition increased significantly over time for all the polymer foams. Osteoblast foam constructs created by seeding 6.83 x 10(5) cells/cm2 on foams with 300-500 microns pores resulted in a cell density of 4.63 x 10(5) cells/cm2 after 1 day in culture; they had alkaline phosphatase activities of 4.28 x 10(-7) and 2.91 x 10(-6) mumol/cell/min on Days 7 and 28, respectively; and they had a cell density that increased to 18.7 x 10(5) cells/cm2 by Day 56. For the same constructs, the mineralized matrix reached a maximum penetration depth of 240 microns from the top surface of the foam and a value of 0.083 mm for mineralized tissue volume per unit of cross sectional area. Seeding density was an important parameter for the constructs, but pore size over the range tested did not affect cell proliferation or function. This study suggests the feasibility of using poly(alpha-hydroxy ester) foams as scaffolding materials for the transplantation of autogenous osteoblasts to regenerate bone tissue.

Non-NASA Center↗
NASA NTRS2001

Micro Navigator

Miniature high-performance low-mass space avionics systems are desired for planned future outer planetary exploration missions (i.e. Europa Orbiter/Lander, Pluto-Kuiper Express). The spacecraft fuel and mass requirements enabling orbit insertion is the driving requirement. The Micro Navigator is an integrated autonomous Guidance, Navigation & Control (GN&C)micro-system that would provide the critical avionics function for navigation, pointing, and precision landing. The Micro Navigator hardware and software allow fusion of data from multiple sensors to provide a single integrated vehicle state vector necessary for six degrees of freedom GN&C. The benefits of this MicroNavigator include: 1) The Micro Navigator employs MEMS devices that promise orders of magnitude reductions in mass power and volume of inertial sensors (accelerometers and gyroscopes), celestial sensing devices (startracker, sun sensor), and computing element; 2) The highly integrated nature of the unit will reduce the cost of flight missions. a) The advanced miniaturization technologies employed by the Micro Navigator lend themselves to mass production, and therefore will reduce production cost of spacecraft. b) The integral approach simplifies interface issues associated with discrete components and reduces cost associated with integration and test of multiple components; and 3) The integration of sensors and processing elements into a single unit will allow the Micro Navigator to encapsulate attitude information and determination functions into a single object. This is particularly beneficial for object-oriented software architectures that are used in advanced spacecraft. Additional information is contained in the original extended abstract.

Blaes, B. R.↗
DOE OSTI2024

Frontiers in Magnetic Materials

Magnetism is crucial to many modern technologies, a driver for condensed matter physics research and one of the most remarkable and diverse properties of matter. We propose to develop understanding of novel magnetism and magnetic related behavior in materials and use this to accelerate the discovery of forefront magnetic materials. The approach is via the connection of magnetic properties to specific structures and materials. Topics that will be addressed are (1) Metallic magnetic materials with unusually low carrier concentrations and/or moments (2) Magnetism arising from unusual chemistry including 4d and 5d magnetism and (3) Materials with strong spin-fluctuations, which can lead to quantum criticality, spin-fluctuation induced superconductivity and other novel quantum behavior. These topics overlap, for example, the 4d ruthenates include ferromagnets (perovskite SrRuO 3 ), extremely high ordering temperature antiferromagnets (honeycomb lattice SrRu 2 O 6 ) and well as quantum materials with strong spin fluctuations (layered perovskite Sr 2 RuO 4 and Sr 3 Ru 2 O 7 ). We will use of density calculations to connect magnetic properties with chemistry and structure and employ phenomenological theories to extend these results to properties that are not directly given by direct first principles methods and we will conduct tests to explore the limitations of density functional approximations and new functionals.

36 MATERIALS SCIENCE↗
NASA NTRS1986

Hex ball torque test

A series of torque tests were performed on four flight-type hex ball universal joints in order to characterize and determine the actual load-carrying capability of this device. The universal joint is a part of manual actuation rods for scientific instruments within the Hubble Space Telescope. It was found that the hex ball will bind slightly during the initial load application. This binding did not affect the function of the universal joint, and the units would wear-in after a few additional loading cycles. The torsional yield load was approximately 50 ft-lb, and was consistent among the four test specimens. Also, the torque required to cause complete failure exceeded 80 ft-lb. It is concluded that the hex ball universal joint is suitable for its intended applications.

Robinson, B. A.↗
DOE OSTI2024

Electrospinner Upgrades for Nanofiber Production

Electrospinning is an inexpensive and flexible method for producing nanofibers. Nanofibers are highly adaptable with potential applications in accelerator target systems, air and water filtration, and biomedicine. This project aims to upgrade and test an existing roll-to-roll electrospinner that is more economical for industrial nanofiber production. Varying the diameter of nanofiber can change its functional properties. The current unit cannot adjust spinneret-collector separation, which determines nanofiber diameter. The electro-spinneret channel also does not have lateral adjustment capabilities for precise alignment. Lastly, the viscosities of our polymer solutions have not been quantified. Solution injection into the channel is presently inconsistent because of imperfect nozzle sizing, resulting in waste and decreased efficiency. Modeling was done with Siemens NX CAD software, and viscosity was measured using a Brookfield DVE-LV viscometer. A dual scissor lift design for channel displacement, powered by a dual-shaft DC motor coupled to precision lead screws, was approved and construction was started. Preliminary channel modifications also were initiated. Going forward, the scissor lift system will be integrated and evaluated with our electrospinner, along with further channel modifications. Viscosity measurements of polyvinyldimethylformamide (PVDF) were recorded with inconsistent results due to inadequate testing conditions. Future viscosity trials must be completed in accordance with testing requirements. The optimization and commercialization of roll-to-roll electrospinner units can make nanofiber production more feasible for many new industries and consumer products.

Black, Niko↗
DOE OSTI2023

Digital Twin Development of FASTR

This work package is focused on creating a digital twin (DT) of the Facility to Alleviate Salt Technology Risks (FASTR) experiment. FASTR is a high-profile facility tasked with maturing molten salt applications such as liquid salt energy storage, concentrated solar power facilities, and molten salt cooling systems supporting other advanced reactor technologies, all of which may be incorporated as components within the Integrated Energy Systems (IES) program. As part of creating a digital twin (DT), verification and validation (V&V) has been performed for the physics-based model, and gaps have been identified. Additionally, a preliminary integration of the FASTR model has been completed with the existing physics-based model of the Thermal Energy Distribution System (TEDS)/Microreactor AGile Non-nuclear Experimental Testbed (MAGNET) facility at Idaho National Laboratory (INL). A Functional Mock-up Unit (FMU) of the physics-based system model and a reduced-order model (ROM) were both used to test for a preliminary hardware in the loop operation when the physical loop was offline. Future tasks could include improving the physics-based model to better match the available experimental data, improving the hardware in the loop integration, and improving the integration with the TEDS model.

14 SOLAR ENERGY↗
NASA NTRS1979

A tactile-output paging communication system for the deaf-blind

A radio frequency paging communication system that has coded vibrotactile outputs suitable for use by deaf-blind people was developed. In concept, the system consists of a base station transmitting and receiving unit and many on-body transmitting and receiving units. The completed system has seven operating modes: fire alarm; time signal; repeated single character Morse code; manual Morse code; emergency aid request; operational status test; and message acknowledge. The on-body units can be addressed in three ways: all units; a group of units; or an individual unit. All the functions developed were integrated into a single package that can be worn on the user's wrist. The control portion of the on-body unit is implemented by a microcomputer. The microcomputer is packaged in a custom-designed hybrid circuit to reduce its physical size.

Baer, J. A.↗
NASA NTRS1987

Servicer system demonstration plan and capability development

An orbital maneuvering vehicle (OMV) front end kit is defined which is capable of performing in-situ fluid resupply and modular maintenance of free flying spacecraft based on the integrated orbital servicing system (IOSS) concept. The compatibility of the IOSS to perform gas and fluid umbilical connect and disconnect functions utilizing connect systems currently available or in development is addressed. A series of tasks involving on-orbit servicing and the engineering test unit (ETU) of the on-orbit service were studied. The objective is the advancement of orbital servicing by expanding the Spacecraft Servicing Demonstration Plan (SSDP) to include detail demonstration planning using the Multimission Modular Spacecraft (MMS) and upgrading the ETU control.

Source record↗
NASA NTRS1990

Simulated rotor test apparatus dynamic characteristics in the 80- by 120-foot wind tunnel

A shake test was conducted in the 80 by 120 foot Wind Tunnel at NASA Ames Research Center, using a load frame and dummy weights to simulate the weight of the NASA Rotor Test Apparatus. The simulated hub was excited with broadband random excitation, and accelerometer responses were measured at various locations. The transfer functions (acceleration per unit excitation force as a function of frequency) for each of the accelerometer responses were computed, and the data were analyzed using modal analysis to estimate the model parameters.

Hoque, M. S.↗
NASA NTRS2006

Space Shuttle Thermal Protection System Repair Flight Experiment Induced Contamination Impacts

NASA s activities to prepare for Flight LF1 (STS-114) included development of a method to repair the Thermal Protection System (TPS) of the Orbiter s leading edge should it be damaged during ascent by impacts from foam, ice, etc . Reinforced Carbon-Carbon (RCC) is used for the leading edge TPS. The repair material that was developed is named Non- Oxide Adhesive eXperimental (NOAX). NOAX is an uncured adhesive material that acts as an ablative repair material. NOAX completes curing during the Orbiter s descent. The Thermal Protection System (TPS) Detailed Test Objective 848 (DTO 848) performed on Flight LF1 (STS-114) characterized the working life, porosity void size in a micro-gravity environment, and the on-orbit performance of the repairs to pre-damaged samples. DTO 848 is also scheduled for Flight ULF1.1 (STS-121) for further characterization of NOAX on-orbit performance. Due to the high material outgassing rates of the NOAX material and concerns with contamination impacts to optically sensitive surfaces, ASTM E 1559 outgassing tests were performed to determine NOAX condensable outgassing rates as a function of time and temperature. Sensitive surfaces of concern include the Extravehicular Mobility Unit (EMU) visor, cameras, and other sensors in proximity to the experiment during the initial time after application. This paper discusses NOAX outgassing characteristics, how the amount of deposition on optically sensitive surfaces while the NOAX is being manipulated on the pre-damaged RCC samples was determined by analysis, and how flight rules were developed to protect those optically sensitive surfaces from excessive contamination where necessary.

Smith, Kendall A.↗
NASA NTRS2014

Logistics Reduction and Repurposing Technology for Long Duration Space Missions

One of NASA's Advanced Exploration Systems (AES) projects is the Logistics Reduction and Repurposing (LRR) project, which has the goal of reducing logistics resupply items through direct and indirect means. Various technologies under development in the project will reduce the launch mass of consumables and their packaging, enable reuse and repurposing of items, and make logistics tracking more efficient. Repurposing also reduces the trash burden onboard spacecraft and indirectly reduces launch mass by one manifest item having two purposes rather than two manifest items each having only one purpose. This paper provides the status of each of the LRR technologies in their third year of development under AES. Advanced clothing systems (ACSs) are being developed to enable clothing to be worn longer, directly reducing launch mass. ACS has completed a ground exercise clothing study in preparation for an International Space Station technology demonstration in 2014. Development of launch packaging containers and other items that can be repurposed on-orbit as part of habitation outfitting has resulted in a logistics-to-living (L2L) concept. L2L has fabricated and evaluated several multi-purpose cargo transfer bags for potential reuse on-orbit. Autonomous logistics management is using radio frequency identification (RFID) to track items and thus reduce crew time for logistics functions. An RFID dense reader prototype is under construction and plans for integrated testing are being made. A heat melt compactor (HMC) second generation unit for processing trash into compact and stable tiles is nearing completion. The HMC prototype compaction chamber has been completed and system development testing is under way. Research has been conducted on the conversion of trash-to-gas (TtG) for high levels of volume reduction and for use in propulsion systems. A steam reformation system was selected for further system definition of the TtG technology.

Broyan, James Lee, Jr.↗
NASA NTRS2022

Night Sky Testing of the Lunar Flashlight Star Tracker

Lunar Flashlight (LF) is a 6U, 14 kg spacecraft being built by the NASA Jet Propulsion Laboratory (JPL). The mission will use IR laser technology to search for volatiles and surface water ice deposits in the permanently shadowed regions (PSR) of the moon in preparation for future human lunar exploration. The fine pointing provided by the Guidance, Navigation and Control (GNC) system is crucial for the spacecraft to successfully reach the moon, enter a lunar orbit, and acquire scientific data. At the center of the GNC system’s ability to determine the spacecraft’s attitude is a star tracker. The LF star tracker is a commercial-off-the-shelf (COTS) unit built into the integrated GNC system provided by Blue Canyon Technologies. Blue Canyon tested the star tracker in a lab environment for basic functionality and attitude estimation capabilities; upon delivery of the hardware to JPL, further testing with a real night sky was desired to determine expected in-flight operational characteristics. JPL maintains the Table Mountain Facility with its suite of ground telescopes, including a 0.6m telescope with an equatorial mount. This stable platform provided a highly accurate method of providing slews and attitude holds akin to what the spacecraft will perform in flight. Therefore, by analyzing the data from these representative night-sky ground tests performed in March, 2021, it is possible to acquire expected flight performance of the star tracker, particularly in regard to the ability of the star tracker to maintain lock on the starfield during planned maneuver types. This paper presents the various tests that have been performed to ensure that the LF star tracker will function as part of the overall GNC system and integrated spacecraft once launched. Test data is included for several key tests, and a path forward towards future integration and testing at the spacecraft level is described.

Baker, John↗