Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “elastic model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

On the nonlinear temperature dependence of residual stresses in solid oxide fuel cells

The residual stresses in a dense yttria-stabilized zirconia (YSZ) layer bonded to a porous NiO-YSZ substrate were measured by X-ray diffraction in air between 25°C and 900°C. In this work, it was found that the residual stresses on the outer surface of the YSZ layer were compressive, that their magnitude increased with decreasing temperature, and that the temperature dependence was nonlinear particularly at temperatures below 600°C. An elastic model that incorporates micromechanics and laminate theory was formulated to successfully predicts the nonlinearity of the temperature dependence of the residual stresses by accounting for the effect of the order-disorder transition experienced by YSZ around 600°C and the magnetic transition of NiO at the Néel temperature around 265°C, on the properties of these materials. The implications of the results for the reliability of solid oxide fuel cells are discussed.

25 ENERGY STORAGE↗
DOE OSTI2016

Structural health monitoring of engineered structures using a space-borne synthetic aperture radar multi-temporal approach: from cultural heritage sites to war zones

Typically, structural health monitoring (SHM) of engineered structures consists of an automated or semi-automated survey system that seeks to assess the structural condition of an anthropogenic structure. The aim of an SHM system is to provide insights into possible induced damage or any inherent signals of deformation affecting the structure in terms of detection, localization, assessment, and prediction. During the last decade there has been a growing interest in using several remote sensing techniques, such as synthetic aperture radar (SAR), for SHM. Constellations of SAR satellites with short repeat time acquisitions permit detailed surveys temporal resolution and millimetric sensitivity to deformation that are at the scales relevant to monitoring large structures. The all-weather multi-temporal characteristics of SAR make its products suitable for SHM systems, especially in areas where in situ measurements are not feasible or not cost effective. To illustrate this capability, we present results from COSMO-SkyMed (CSK) and TerraSAR-X SAR observations applied to the remote sensing of engineered structures. We show how by using multiple-geometry SAR-based products which exploit both phase and amplitude of the SAR signal we can address the main objectives of an SHM system including detection and localization. We highlight that, when external data such as rain or temperature records are available or simple elastic models can be assumed, the SAR-based SHM capability can also provide an interpretation in terms of assessment and prediction. We highlight examples of the potential for such imaging capabilities to enable advances in SHM from space, focusing on dams and cultural heritage areas.

47 OTHER INSTRUMENTATION↗
DOE OSTI2016

Reverse depletion effects and the determination of ligand density on some spherical bioparticles

In cell environments crowded with macromolecules, the depletion effects act and assist in the assembly of a wide range of cellular structures, from the cytoskeleton to the chromatin loop, which are well accepted. But a recent quantum dot experiment indicated that the dimensions of the receptor–ligand complex have strong effects on the size-dependent exclusion of proteins in cell environments. In this article, a continuum elastic model is constructed to resolve the competition between the dimension of the receptor–ligand complex and depletion effects in the endocytosis of a spherical virus-like bioparticle. Our results show that the depletion effects do not always assist endocytosis of a spherical virus-like bioparticle; while the dimension of the ligand–receptor complex is larger than the size of a small bioparticle in cell environments, the depletion effects do not work and reverse effects appear. The ligand density covered on the virus can be identified quantitatively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2012

Mimetic Theory for Cell-Centered Lagrangian Finite Volume Formulation on General Unstructured Grids

A finite volume cell-centered Lagrangian scheme for solving large deformation problems is constructed based on the hypo-elastic model and using the mimetic theory. Rigorous analysis in the context of gas and solid dynamics, and arbitrary polygonal meshes, is presented to demonstrate the ability of cell-centered schemes in mimicking the continuum properties and principles at the discrete level. A new mimetic formulation based gradient evaluation technique and physics-based, frame independent and symmetry preserving slope limiters are proposed. Furthermore, a physically consistent dissipation model is employed which is both robust and inexpensive to implement. The cell-centered scheme along with these additional new features are applied to solve solids undergoing elasto-plastic deformation.

42 ENGINEERING↗
DOE OSTI2015

Geomechanical and Fluid Transport Properties

Complex changes to fluid and mechanical properties of a pyrolyzing formation could lead to significant subsidence. Capturing subsidence requires accounting for changes in porosity due to generation and drainage of fluid. Pores, permeability and pore pressure are generated during pyrolysis of kerogen into oil and gas. In a series reaction scheme, oil is an intermediate product of pyrolysis. A large portion of oil-range fluids may be lost in an in-situ operation if the oil produced cannot be drained quickly enough. Petroleum fluid quality and production are highly dependent on the relative rates of creation, destruction, and transport of oil and gas in a given volume. All of these are dependent on the heating rate of oil shale. If oil shale is heated quickly, fluid flow may increase, but at a cost to the amount of oil that is finally extracted. To account for the effect of pore fluid on mechanical deformation, an elastic model was combined with a Mohr-Coulomb failure criterion and Biot’s linear consolidation model. The overall model is poroelastic, because it accounts for rock deforming by considering the response of the bulk system and the pore fluids it contains. Biot’s linear model includes all ways that pore fluid volume can change in a system, including stress-strain interactions between pores and the bulk material. Additionally, the model captures the distinction between fluid and solid matrix compression and describes how bulk deformation is affected by fluid drainage. The fluid response to changing stress is affected by changes in pore pressure, while the bulk material responds to effective stress changes. To capture all of these effects, a number of theoretical and empirical models were employed in FLAC3D™, a rock-mechanics software package produced by Itasca Consulting Group. The basic capabilities of FLAC3D™ have been supplemented by customized algorithms for the simulation package. The most important contribution has been to develop a methodology for describing poro-thermo-mechanical properties of oil shale across the complete chronology of in situ pyrolysis. This report highlights those methods and results for inferring realistic oil shale properties.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2022

High-Entropy Borides under Extreme Environment of Pressures and Temperatures

The high-entropy transition metal borides containing a random distribution of five or more constituent metallic elements offer novel opportunities in designing materials that show crystalline phase stability, high strength, and thermal oxidation resistance under extreme conditions. We present a comprehensive theoretical and experimental investigation of prototypical high-entropy boride (HEB) materials such as (Hf, Mo, Nb, Ta, Ti)B2 and (Hf, Mo, Nb, Ta, Zr)B2 under extreme environments of pressures and temperatures. The theoretical tools include modeling elastic properties by special quasi-random structures that predict a bulk modulus of 288 GPa and a shear modulus of 215 GPa at ambient conditions. HEB samples were synthesized under high pressures and high temperatures and studied to 9.5 GPa and 2273 K in a large-volume pressure cell. The thermal equation of state measurement yielded a bulk modulus of 276 GPa, in excellent agreement with theory. The measured compressive yield strength by radial X-ray diffraction technique in a diamond anvil cell was 28 GPa at a pressure of 65 GPa, which is a significant fraction of the shear modulus at high pressures. The high compressive strength and phase stability of this material under high pressures and high temperatures make it an ideal candidate for application as a structural material in nuclear and aerospace fields.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microtubules soften due to cross-sectional flattening

We use optical trapping to continuously bend an isolated microtubule while simultaneously measuring the applied force and the resulting filament strain, thus allowing us to determine its elastic properties over a wide range of applied strains. We find that, while in the low-strain regime, microtubules may be quantitatively described in terms of the classical Euler-Bernoulli elastic filament, above a critical strain they deviate from this simple elastic model, showing a softening response with increasing deformations. A three-dimensional thin-shell model, in which the increased mechanical compliance is caused by flattening and eventual buckling of the filament cross-section, captures this softening effect in the high strain regime and yields quantitative values of the effective mechanical properties of microtubules. Our results demonstrate that properties of microtubules are highly dependent on the magnitude of the applied strain and offer a new interpretation for the large variety in microtubule mechanical data measured by different methods.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1972

Wind tunnel buffet load measuring technique

Indirect force measurement technique estimates unsteady forces acting on elastic model during wind tunnel tests. Measurement of forces is practically insensitive to errors in aeroelastic scaling between model and full-scale structure, simplifying design, fabrication and dynamic calibration.

Chang, C. S.↗
NASA NTRS1973

A study of crack closure in fatigue

Crack closure phenomenon in fatigue was studied by using a Ti-6Al-4V titanium alloy. The occurrence of crack closure was directly measured by an electrical-potential method, and indirectly by load-strain measurement. The experimental results showed that the onset of crack closure depends on both the stress ratio, and the maximum stress intensity factor. No crack closure was observed for stress ratio, greater than 0.3 in this alloy. A two-dimensional elastic model was used to explain the behavior of the recorded load-strain curves. Closure force was estimated by using this model. Yield level stress was found near the crack tip. Based on this estimated closure force, the crack opening displacement was calculated. This result showed that onset of crack closure detected by electrical-potential measurement and crack-opening-displacement measurement is the same. The implications of crack closure on fatigue crack are considered. The experimental results show that crack closure cannot fully account for the effect of stress ratio, on crack growth, and that it cannot be regarded as the sole cause for delay.

Shih, T. T.↗
NASA NTRS1974

Wave transmission characteristics and anisotropy of canine carotid arteries

A method was developed to generate and record three types of small amplitude waves (pressure, torsion and axial) in the exposed carotid artery of anesthetized dogs. The pressure waves were studied with the aid of miniature pressure transducers; electro-optical tracking units monitored the axial and circumferential surface displacements. Results from 6 dogs are presented in the form of the phase velocities and attenuation of three types of waves. The data demonstrate incompatibility with an isotropic elastic model for the mechanical behavior of the artery. The measured damping appears to be primarily due to the viscoelastic properties of the vessel wall material.

Moritz, W. E.↗
NASA NTRS1975

Track/train dynamics test procedure transfer function test

A transfer function vibration test was made on an 80 ton open hopper freight car in an effort to obtain validation data on the car's nonlinear elastic model. Test configuration, handling, test facilities, test operations, and data acquisition/reduction activities necessary to meet the conditions of test requirements are given.

Vigil, R. A.↗
NASA NTRS1974

Surfaces and interfaces of glass and ceramics; Proceedings of the International Symposium on Special Topics in Ceramics, Alfred University, Alfred, N.Y., August 27-29, 1973

The characterization of surfaces and interfaces is considered along with the infrared spectra of several N-containing compounds absorbed on montmorillonites, applications of surface characterization techniques to glasses, the observation of electronic spectra in glass and ceramic surfaces, a method for determining the preferred orientation of crystallites normal to a surface, and the friction and wear behavior of glasses and ceramics. Attention is given to the wear behavior of cast surface composites, an experimental investigation of the dynamic and thermal characteristics of the ceramic stock removal process, a dynamic elastic model of ceramic stock removal, and the structure and properties of solid surfaces. Individual items are announced in this issue.

Frechette, V. D.↗
NASA NTRS1978

The observability of the celestial pole and its nutations

The expected motion characteristics of the real earth are systematically analysed based on available dynamical theories for the rigid model, the elastic earth model and the earth model with liquid core. The various axes which are implicit in the dynamical theories are investigated regarding observability on the basis of astronomical observations and suitability for defining reference directions. The observational insignificance of the ''diurnal polar motion'' is demonstrated. A special effort is made to clarify customarily used terminology.

Leick, A.↗
NASA NTRS1979

The effects of strain and temperature on the dynamic properties of elastomers

This paper presents the results of a program of analysis and tests to determine the dynamic properties of elastomers as a function of strain and ambient temperature. Measurements were also made to determine the temperature distribution in the elastomer samples during the tests. These measured properties were compared with analytical predictions based on a visco-elastic model designed to take into account the self-heating of the materials as a function of strain. The test method used was well-established Base Excitation Resonant Mass Technique. The specimens tested were two cylindrical button compression specimens and a shear specimen. Strain was shown to be an important parameter in determining the dynamic properties of the elastomers. In general, these properties were much more sensitive to strain than to frequency. The self-heating effect was found to account for a portion of the strain sensitivity of these properties.

Darlow, M. S.↗
NASA NTRS1981

The variation of magma discharge during basaltic eruptions

The rate at which basaltic magma is discharged during many eruptions varies substantially. An individual eruption has an eruption rate, which is the volumetric rate of discharge averaged over the whole or a major part of an eruption, and an effusion rate, which is the volumetric flux rate at any given time. In many cases, the effusion rate soon reaches a maximum after a short period of waxing flow (partly because of magmatic expansion); it then falls more slowly in the later parts of the eruption. The release of elastic strain energy from stored magma and the subvolcanic reservoir during eruption can give a waning flow of this type an exponential form. A comparison of the eruption rates of eruptions of Mauna Loa, Kilauea and Etna shows that for each volcano there is a trend of decreasing effusion rate with increasing duration of eruption. It is noted that this relationship is not predicted by a simple elastic model of magma release. Two other processes are invoked to explain the eruptive histories of these volcanoes: modification of the eruptive conduits and the continued supply of magma from depth during eruption.

Wadge, G.↗
NASA NTRS1981

The variation of magma discharge during basaltic eruptions

The different types of magmatic flow in basaltic eruptions are discussed, and processes explaining the eruptive history of specific volcanoes are investigated. The effusion rate curve is divided into waxing and waning flow parts, and the ideal, elastic response of the reservoir in the waning phase is analytically shown. Historical eruption rates of Mauna Loa, Kilauea, and Etna are presented, demonstrating that for each volcano there is a trend of decreasing rate with increasing duration of eruption, a relationship not predicted by a simple elastic model of magma release. The eruptive histories of these volcanoes is explained by the processes of modification of the eruptive conduits and the continued supply of magma from depth during eruption. Discharge variations from Paricutin, Hekla, and Kilauea Iki are discussed in detail.

Wadge, G.↗
NASA NTRS1984

An analysis of rotor blade twist variables associated with different Euler sequences and pretwist treatments

A nonlinear analysis which is necessary to adequately model elastic helicopter rotor blades experiencing moderately large deformations was examined. The analysis must be based on an appropriate description of the blade's deformation geometry including elastic bending and twist. Built-in pretwist angles complicate the deformation process ant its definition. Relationships between the twist variables associated with different rotation sequences and corresponding forms of the transformation matrix are lasted. Relationships between the twist variables associated with first, the pretwist combined with the deformation twist are included. Many of the corresponding forms of the transformation matrix for the two cases are listed. It is shown that twist variables connected with the combined twist treatment are related to those where the pretwist is applied initially. A method to determine the relationships and some results are outlined. A procedure to evaluate the transformation matrix that eliminates the Eulerlike sequence altogether is demonstrated. The resulting form of the transformation matrix is unaffected by rotation sequence or pretwist treatment.

Alkire, K.↗
NASA NTRS1984

Flexure of the continental lithosphere beneath Apennine and Carpathian foredeep basins

The preservation of foredeep basins after an associated mountain belt has been greatly reduced by erosion suggests that an additional load must act on the subducted slab's lithosphere independently of topography. This hypothesis is presently tested for the case of young orogenic belts, through the construction of transects through the Apennine and outer Carpathian thrust belts of the Mediterranean region. A simple elastic model is used to show that the topographic loads present along the transects are not sufficient to cause the observed plate deflection, suggesting that an additional load or downward force is acting on the plate to generate the plate deflection observed. It is proposed that this extra load is due either to the negative buoyancy contrast between the subducted slab and the asthenosphere, or to the crustal structure's modification by backarc rifling in the hinterland.

Royden, L.↗