Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “direct injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Reaction-space analysis of homogeneous charge compression ignition combustion with varying levels of fuel stratification under positive and negative valve overlap conditions

Full-cycle computational fluid dynamics simulations with gasoline chemical kinetics were performed to determine the impact of breathing and fuel injection strategies on thermal and compositional stratification, combustion and emissions during homogeneous charge compression ignition combustion. The simulations examined positive valve overlap and negative valve overlap strategies, along with fueling by port fuel injection and direct injection. The resulting charge mass distributions were analyzed prior to ignition using ignition delay as a reactivity metric. The reactivity stratification arising from differences in the distributions of fuel–oxygen equivalence ratio (Φ FO ), oxygen molar fraction (χ O2 ) and temperature (T) was determined for three parametric studies. In the first study, the reactivity stratification and burn duration for positive valve overlap valve events with port fuel injection and early direct injection were nearly identical and were dominated by wall-driven thermal stratification. nitrogen oxide (NO) and carbon monoxide (CO) emissions were negligible for both injection strategies. In the second study, which examined negative valve overlap valve events with direct injection and port fuel injection, reactivity stratification increased for direct injection as the Φ FO and T distributions associated with direct fuel injection into the hot residual gas were positively correlated; however, the latent heat absorbed from the hot residual gas by the evaporating direct injection fuel jet reduced the overall thermal and reactivity stratification. These stratification effects were offsetting, resulting in similar reactivity stratification and burn durations for the two injection strategies. The higher local burned gas temperatures with direct injection resulted in an order of magnitude increase in NO, while incomplete combustion of locally over-lean regions led to a sevenfold increase in CO emissions compared to port fuel injection. The final study evaluated positive valve overlap and negative valve overlap valve events with direct injection. Furthermore, relative to positive valve overlap, the negative valve overlap condition had a wider reactivity stratification, a longer burn duration and higher NO and CO emissions associated with reduced fuel–air mixing.

33 ADVANCED PROPULSION SYSTEMS↗

Ag ion generation irradiated by Nd:YAG laser onto solid target for use of direct plasma injection scheme

Direct plasma injection scheme (DPIS) is an acceleration scheme which consists of laser ion source and a radio frequency quadrupole linac (RFQ) linac for high current heavy ion acceleration. With this scheme, over 60 mA of carbon and aluminum beam was achieved at the RFQ exit. We are planning to accelerate Ag ions as a heavier material than used previously. Ag plasma properties using Nd:YAG laser (2.3 J/6 ns) were measured toward the acceleration with DPIS. The results showed that the highest ion yield was obtained at Ag{sup 15+}. Based on these results, multicharged Ag ion transportation inside RFQ was simulated and the expected current at the exit of RFQ was over 14 mA for Ag{sup 15+} using the RFQ dedicated for Ag acceleration.

36 MATERIALS SCIENCE↗

Experimental Investigation of a Multiplex Fuel Injector Module With Discrete Jet Swirlers for Low Emission Combustors

A low-NOx emissions combustor concept has been demonstrated in flame-tube tests. A lean-direct injection (LDI) concept was used where the fuel is injected directly into the flame zone and the overall equivalence ratio of the mixture is lean. The LDI concept described in this report is a multiplex fuel injector module containing multipoint fuel injection tips and multi-burning zones. The injector module comprises 25 equally spaced injection tips within a 76 by 76 mm area that fits into the flame-tube duct. The air swirlers were made from a concave plate on the axis of the fuel injector using drilled holes at an angle to the axis of the fuel injector. The NOx levels were quite low and are greater than 70 percent lower than the 1996 ICAO standard. At an inlet temperature of 810 K, inlet pressure of 2760 kPa, pressure drop of 4 percent and a flame temperature of 1900 K with JP8 fuel, the NOx emission index was 9. The 25-point injector module exhibited the most uniform radial distribution of fuel-air mixture and NOx emissions in the flame tube when compared to other multipoint injection devices. A correlation is developed relating the NOx emissions to inlet temperature, inlet pressure, equivalence ratio and pressure drop.

Tacina, Robert↗

Assessment of impinged flame structure in high-pressure direct diesel injection

Spray impingement often occurs during cold-start in direct-injection diesel engines, affecting the subsequent combustion process by altering the local flow condition. This work has investigated the impinged flame structure by examining local expansion distance and planar curvature of the boundary in details. The experiments were carried out in a constant volume combustion chamber. The injection pressure and ambient density were varied from 120 to 180 MPa and 14.8 to 30.0 kg/m 3 under non-vaporizing conditions, respectively. For reacting conditions, the injection pressure and ambient density were fixed at 150 MPa and 22.8 kg/m 3 but with different ambient temperatures from 800 to 1000 K. Unlike orthogonal spray impingement, the profile of expansion distance along the radial direction at the 60° impinging angle is non-uniform but the profile is comparable between the non-vaporizing and reacting conditions under the same injection pressure and ambient density. With the help of Intensity-aXial-Time method, the most intensive soot luminosity region and Mie scattering intensity region are identified and the region has been found to be along the impinged spray axial direction. Outmost boundary of an impinged flame is found to have wrinkles attributed to air entrainment. The temporal level of flame wrinkles is higher in reacting conditions than in non-vaporizing conditions. The scatter distribution of the boundary curvature and near-field soot formation illustrates an inverted “S” shape correlation with time. High flame luminosity is found to be formed in concave regions while less soot is formed in convex regions. This inverted S-shape is a new finding of the state relationship at the solid–liquid–gas impinged flame propagation. Finally, heat flux measurement through the plate is examined.

Engineering↗

Particle simulation for direct plasma injection in a radio frequency quadrupole matching section

We have been investigating direct plasma injection scheme (DPIS) for high-intensity heavy-ion beam acceleration. In the DPIS, laser-produced plasma is directly injected into a radio frequency quadrupole (RFQ) linac. To study the beam dynamics of the ion injection in the DPIS, we tracked particle motions in the RFQ matching section using three-dimensional particle-in-cell method. As a result of the numerical simulation, we found that the electrostatic field generated by the extraction electrode reduces the transmission efficiency. To avoid the radially defocusing force, the input beam into the RFQ has to be initially convergent. In the DPIS, further optimization of the plasma density is required for better matching.

43 PARTICLE ACCELERATORS↗

Time structure of an accelerated beam using a radio-frequency quadrupole linac with direct plasma injection scheme

In direct plasma injection scheme, the relation between the ion current from a laser ion source and the accelerated beam current by a radio-frequency quadrupole (RFQ) linac was studied by a series of the following analyses. First, ion current at beam extraction was calculated from measured plasma parameters using a scaling law. Second, the beam emittance at the entrance of acceleration electrode region was evaluated by the simulation of the ion extraction out of the ion source plasma using the result of the first calculation. Last, the accelerated beam current could be reproduced by the simulation of beam acceleration using the results of the second. The second calculation revealed the time variation in the injected beam parameter to the RFQ linac. Then it was proved that the time structure of the accelerated beam was different from that of the injection beam because the degree of the matching between the injected beam emittance and the RFQ acceptance varied with time.

43 PARTICLE ACCELERATORS↗

Low NOx, Lean Direct Wall Injection Combustor Concept Developed

The low-emissions combustor development at the NASA Glenn Research Center is directed toward advanced high-pressure aircraft gas turbine applications. The emphasis of this research is to reduce nitrogen oxides (NOx) at high-power conditions and to maintain carbon monoxide and unburned hydrocarbons at their current low levels at low-power conditions. Low-NOx combustors can be classified into rich burn and lean burn concepts. Lean burn combustors can be further classified into lean-premixed-prevaporized (LPP) and lean direct injection (LDI) combustors. In both concepts, all the combustor air, except for liner cooling flow, enters through the combustor dome so that the combustion occurs at the lowest possible flame temperature. The LPP concept has been shown to have the lowest NOx emissions, but for advanced high-pressure-ratio engines, the possibly of autoignition or flashback precludes its use. LDI differs from LPP in that the fuel is injected directly into the flame zone and, thus, does not have the potential for autoignition or flashback and should have greater stability. However, since it is not premixed and prevaporized, the key is good atomization and mixing of the fuel quickly and uniformly so that flame temperatures are low and NOx formation levels are comparable to those of LPP.

Tacina, Robert R.↗

Flame Tube NOx Emissions Using a Lean-Direct-Wall-Injection Combustor Concept

A low-NOx emissions combustor concept has been demonstrated in flame tube tests. A lean-direct injection concept was used where the fuel is injected directly into the flame zone and the overall fuel-air mixture is lean. In this concept the air is swirled upstream of a venturi section and the fuel is injected radially inward into the air stream from the throat section using a plain-orifice injector. Configurations have two-, four-, or six-wall fuel injectors and in some cases fuel is also injected from an axially located simplex pressure atomizer. Various orifice sizes of the plain-orifice injector were evaluated for the effect on NOx. Test conditions were inlet temperatures up to 8 1 OK, inlet pressures up to 2760 kPa, and flame temperatures up to 2100 K. A correlation is developed relating the NOx emissions to inlet temperature, inlet pressure, fuel-air ratio and pressure drop. Assuming that 15 percent of the combustion air would be used for liner cooling and using an advanced engine cycle, for the best configuration, the NOx emissions using the correlation is estimated to be <75 percent of the 1996 ICAO standard.

Tacina, Robert R.↗

Direct plasma injection scheme with various ion beams

The laser ion source is one of the most powerful heavy ion sources. However, it is difficult to obtain good stability and to control its intense current. To overcome these difficulties, we proposed a new beam injection scheme called 'direct plasma injection scheme'. Following this it was established to provide various species with desired charge state as an intense accelerated beam. Carbon, aluminum and iron beams have been tested.

43 PARTICLE ACCELERATORS↗

Extraction of ion beam from laser ion source for direct plasma injection scheme

Laser ion sources are expected to be used in various applications of heavy ion beam technology. The plasma direct injection scheme (DPIS) is a method in which ion beams extracted from a laser ion source are directly injected into a radio frequency quadrupole (RFQ) linear accelerator. In this study, a new shape of the plasma electrode with a concave surface for the DPIS was proposed to inject a converging beam to a cavity of RFQ accelerator. This approach allows the use of a large-diameter extraction electrode, which is not limited by the aperture of the RFQ electrode rods. The DPIS, using the concave surface electrode, was employed to accelerate C 6+ ion beams. The results indicated that both the beam current and the number of ions increased nearly twice with the proposed electrode shape compared to values obtained with the conventional electrode. This enhancement corresponded to the increased extraction area of the beam.

43 PARTICLE ACCELERATORS↗

Influence of charge motion and compression ratio on the performance of a combustion concept employing in-cylinder gasoline and natural gas

The present paper represents a small piece of an extensive experimental effort investigating the dual-fuel operation of a light-duty spark ignited engine. Natural gas (NG) was directly injected into the cylinder and gasoline was injected into the intake-port. Direct injection (DI) of NG was used in order to overcome the power density loss usually experienced with NG port-fuel injection (PFI) as it allows an injection after intake valve closing. Having two separate fuel systems allows for a continuum of in-cylinder blend levels from pure gasoline to pure NG operation. The huge benefit of gasoline is its availability and energy density, whereas NG allows efficient operation at high load due to improved combustion phasing enabled by its higher knock resistance. Furthermore, using NG allowed a reduction of carbon dioxide emissions across the entire engine map due to the higher hydrogen-to-carbon ratio. Exhaust gas recirculation (EGR) was used to (a) increase efficiency at low and part-load operation and (b) reduce the propensity of knock at higher compression ratios (CRs) thereby enabling blend levels with greater amount of gasoline across a wider operating range. Two integral engine parameters, CR and in cylinder turbulence levels, were varied in order to study their influence on efficiency, emissions, and performance over a specific speed and load range. Increasing the CR from 10.5 to 14.5 allowed an absolute increase in indicated thermal efficiency of snore than 3% for 7.5% NG (2.5% gasoline) operation at 8 bar net indicated mean effective pressure (IMEP) and 2500 rpm. However, as anticipated, the achievable peak load at CR 14.5 with 100% gasoline was greatly reduced due to its lower knock resistance. The in cylinder turbulence level was varied by means of tumble plates (TPs) as well as an insert for the NG injector that guides the injection "spray" to augment the tumble motion. The usage of TPs showed a significant increase in EGR dilution tolerance for pure gasoline operation, however, no such impact was found for blended operation of gasoline and NG.

Sevik, James↗

Fuel-Neutral Studies of PM Transportation Emissions

New gasoline engine technologies such as Spark Ignition Direct Injection (SIDI), Gasoline Direct Injection Compression Ignition (GDICI), and Reaction Controlled Compression Ignition (RCCI) offer the possibility of dramatically increasing the fuel efficiency of future vehicles. One drawback to these advanced engines is that they have the potential to produce higher levels of exhaust particulates than current Port Fuel Injection (PFI) engines. Regulation of engine particulate emissions in Europe is moving from mass-based standards toward number-based standards. Due to growing health concerns surrounding nano-aerosols, it is likely that similar standards will eventually be applied in the United States. This would place more emphasis on the reliable removal of smaller particles, which make up the vast majority of the particulates generated on a number basis. While Diesel Particulate Filters (DPF) have become standard, different filter systems would likely be required for advanced gasoline vehicles, due to factors such as differing particulate properties and higher exhaust temperatures. High exhaust temperatures can limit the accumulation of a soot cake, which performs most of the actual filtration in a typical DPF system.

fuel blends↗

Construction of a Direct Water-Injected Two-Stroke Engine for Phased Direct Fuel Injection-High Pressure Charging Investigations

The development of a water injected Orbital Combustion Process (OCP) engine was conducted to assess the viability of using the powerplant for high altitude NASA aircraft and General Aviation (GA) applications. An OCP direct fuel injected, 1.2 liter, three cylinder, two-stroke engine has been enhanced to independently inject water directly into the combustion chamber. The engine currently demonstrates low brake specific fuel consumption capability and an excellent power to weight ratio. With direct water injection, significant improvements can be made to engine power, to knock limits/ignition advance timing, and to engine NO(x) emissions. The principal aim of the testing was to validate a cyclic model developed by the Systems Analysis Branch at NASA Ames Research Center. The work is a continuation of Ames' investigations into a Phased Direct Fuel Injection Engine with High Pressure Charging (PDFI-ITPC).

Somsel, James P.↗

Direct plasma injection scheme in accelerators (invited)

The idea of direct plasma injection scheme (DPIS) was proposed in 2000. This new technique has been studied and proven to accelerate intense ion beams. To provide medium mass ions with highly charged states, small tabletop solid lasers were used for plasma production. Based on the measured plasma properties, aluminum and carbon ions were accelerated with more than 60 mA of current. The next experiments will use an radio frequency quadrupole designed for q/m=1/6 and explore beam productions using targets up to silver, and future work will explore production up to uranium. The DPIS has been established and is ready to be used with various accelerators which require pulsed high current, high charge state ion beams.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct plasma injection scheme with beam extraction in a radio frequency quadrupole linac cavity

Direct plasma injection scheme (DPIS) is a recently developed idea about beam injection into a radio frequency quadrupole (RFQ) linac to obtain high current pulsed heavy ion beam. Since a laser ion source is directly connected to an RFQ linac, a low energy beam transport is not needed. An ion beam is extracted at the edge of the cavity. We shifted the extraction position in the RFQ cavity to improve the beam loss problem due to beam diverging before arriving at the entrance of the RFQ electrode region. In this scheme, ion beam is extracted at the entrance of the RFQ electrode region and the extracted beam is immediately captured by a rf quadrupole electric field. A plasma electrode is inserted in the accelerator resonant cavity. It is required to avoid serious effect on the acceleration characteristics of the RFQ linac. The rf properties were measured using a network analyzer to verify the effect. The shifts of resonant frequency were negligibly small by inserting the electrode. The measurements of the electric field distribution along the beam axis in the RFQ linac showed that the plasma electrode had little effect on it. The result of beam acceleration experiment showed that the beam current was increased by about 20%. It was confirmed that the beam loss was reduced by this scheme.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗