Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dioxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Potential of U.S. Marine and Offshore Wind Energy to Power Marine Carbon Dioxide Removal

The goal of this project was to provide a preliminary feasibility assessment of powering different marine carbon dioxide removal (mCDR), carbon capture (mCC), and carbon sequestration (mCS) strategies with marine energy. The investigation focused on methods with clear power requirements at sea beyond monitoring such as artificial upwelling, deep ocean storage, electrochemical (eChem) mCDR and mCC, offshore microalgae cultivation, and seaweed farming and sinking. The project found that eChem mCDR powered by marine energy and offshore wind energy available in the United States could meet global CDR scales needed by 2040 and 2050 to limit warming to 1.5 degrees C by 2100 and marine energy alone could greatly contribute to reaching scales needed by 2040. Note that this preliminary estimate assumes that it is possible to harvest all the marine and offshore wind resources available in the United States with existing technology options. Though the biological methods were limited in scale they still hold promise in developing carbon negative fuels and products which can reduce emissions in the short term.

afforestation↗
DOE OSTI2025

Phonon-Spin Scattering from Unpaired f-electrons in U atoms and It’s Influence on Thermal Transport in Uranium-doped Thorium Dioxide Single Crystals

In this work, impact of low level of uranium (U) atom substitution on thermal conductivity of thorium dioxide (ThO2) is investigated. ThO2 is an electronic insulator with a wide optical band-gap and no unpaired electrons whose thermal transport is governed by phonons. U-substitution introduces unpaired f-electrons resulting in paramagnetic behavior of U-ThO2 at room temperature, which significantly suppresses its thermal conductivity. A single crystal of U-ThO2 with graded composition of U is grown using a hydrothermal synthesis method, and thermal conductivity measurements are performed in regions with uniform composition of U at levels of 0%, 6%, 9% and 16%. Measured thermal conductivity profiles over 77–300 K temperature range are analyzed using an analytical expression for phonon-mediated thermal transport based on Klemens-Callaway model. Temperature dependent thermal conductivity is found to deviate significantly from the Rayleigh scattering trend expected for a simple substitutional point defect with a small perturbation to mass and interatomic forces. With the resonant scattering term, observed large suppression of thermal conductivity at low temperatures can be closely reproduced. Additionally, the extracted phonon-spin coupling constants imply a nonlinear relation of phonon-spin interaction intensity with respect to U doping percentage. Our study reveals how phonon-spin scattering contributed by unpaired f-electrons in U atoms influences thermal transport in the U-ThO2 system.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Oxygen‐Assisted Supercapacitive Swing Adsorption of Carbon Dioxide

Abstract We report on the supercapacitive swing adsorption (SSA) of carbon dioxide at different voltage windows in the presence of oxygen using activated carbon electrodes, and deliquescent, aqueous electrolytes. The presence of O 2 in the CO 2 /N 2 gas mixture results in an up to 11 times higher CO 2 adsorption capacity with 3 M MgBr 2 (at 0.6 V) and up to 4–5 times higher adsorption capacity with 3 M MgCl 2 (at 1 V). A tradeoff between high CO 2 adsorption capacities and lower coulombic efficiencies was observed at voltages above 0.6 V. The energetic and adsorptive performance of the electrodes in the presence of oxygen below 0.5 V was similar to the performance with a CO 2 /N 2 mixture without oxygen at 1 V. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) of the electrodes demonstrate that the specific capacitance increases while the diffusion resistance decreases in the presence of oxygen. Oxygen concentrations ranging between 5–20 % give similar energetic and adsorptive performance. The electrodes exhibit stable performance for up to 100 cycles of operation.

Bilal, Muhammad↗
DOE OSTI2023

Highly Selective Photoelectroreduction of Carbon Dioxide to Ethanol over Graphene/Silicon Carbide Composites

Using sunlight to produce valuable chemicals and fuels from carbon dioxide (CO 2 ), i.e., artificial photosynthesis (AP) is a promising strategy to achieve solar energy storage and a negative carbon cycle. However, selective synthesis of C 2 compounds with a high CO 2 conversion rate remains challenging for current AP technologies. Here, we performed CO 2 photoelectroreduction over a graphene/silicon carbide (SiC) catalyst under simulated solar irradiation with ethanol (C 2 H 5 OH) selectivity of>99 % and a CO 2 conversion rate of up to 17.1 mmol g cat -1 h -1 with sustained performance. Experimental and theoretical investigations indicated an optimal interfacial layer to facilitate the transfer of photogenerated electrons from the SiC substrate to the few-layer graphene overlayer, which also favored an efficient CO 2 to C 2 H 5 OH conversion pathway.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Oxygen‐Assisted Supercapacitive Swing Adsorption of Carbon Dioxide

We report on the supercapacitive swing adsorption (SSA) of carbon dioxide at different voltage windows in the presence of oxygen using activated carbon electrodes, and deliquescent, aqueous electrolytes. The presence of O 2 in the CO 2 /N 2 gas mixture results in an up to 11 times higher CO 2 adsorption capacity with 3 M MgBr 2 (at 0.6 V) and up to 4–5 times higher adsorption capacity with 3 M MgCl 2 (at 1 V). A tradeoff between high CO 2 adsorption capacities and lower coulombic efficiencies was observed at voltages above 0.6 V. The energetic and adsorptive performance of the electrodes in the presence of oxygen below 0.5 V was similar to the performance with a CO 2 /N 2 mixture without oxygen at 1 V. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) of the electrodes demonstrate that the specific capacitance increases while the diffusion resistance decreases in the presence of oxygen. Oxygen concentrations ranging between 5–20 % give similar energetic and adsorptive performance. The electrodes exhibit stable performance for up to 100 cycles of operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Toward Rational Design of Nickel Catalysts for Thermocatalytic Decomposition of Methane for Carbon Dioxide-Free Hydrogen and Value-Added Carbon Co-Product: A Review

Thermocatalytic decomposition of methane provides opportunities for hydrogen (H2) production with no emission of carbon dioxide. However, high-value carbon products need to be produced for economic deployment of thermocatalytic decomposition and to achieve a minimum H 2 selling price below the U.S, Department of Energy target of $ 1/kg H 2 . In this review, we re-evaluate data on catalyst development reported in the literature and propose correlations between catalyst characteristics, catalytic stability, and properties of carbon co-products. In the first part of the review, growth mechanisms for carbon nanotubes using state-of-the-art chemical vapor deposition are reviewed to catalog the effects of catalyst characteristics, the influence of carbon sources, interactions between metal particles and supports, and metal particle sizes on carbon growth. In the second part, representative developments in mono-, bi-, and tri-metallic nickel catalysts are highlighted. We present kinetic analysis of reactions catalyzed by mono-metallic nickel catalysts, which generates a correlation between metal particle size and catalyst stability. Rational design of Ni-based catalysts for TCD of methane requires attention to the size of the metal particle and effective normalization of the reaction rates. Further attention to the distribution of the metal particle sizes may help identify catalyst properties that contribute longevity and selectivity to processes that use them. While it is tempting to focus on the highest valued carbon products (e.g., CNTs and CFs), analysis of the markets for other carbon products suggests that a more flexible approach may generate comparable returns without the risk associated with specialization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Hybrid Carbon Dioxide Reduction Photocatalysts Consisting of Macrocyclic Cobalt(III) Complexes Deposited on Semiconductor Surfaces

Hybrid photocatalysts can be prepared by coupling metal ligand complexes with light-harvesting semiconductors. It is often challenging and time consuming to derivatize ligands with anchoring groups to effectively attach onto surfaces. In this study, we synthesized hybrid carbon dioxide reduction photocatalysts by directly depositing two macrocyclic Co(III) complexes on three different semiconductor surfaces (TiO 2 , N-Ta 2 O 5 and C 3 N 4 ). The resulting hybrid photocatalysts were characterized with various techniques and tested in CO 2 reduction reactions under different light conditions. Excellent visible-light CO 2 -reduction activity was obtained using C 3 N 4 as the light-harvesting semiconductor. Furthermore, density functional theory calculations were conducted to help understand interactions between the cobalt complexes with a model TiO 2 surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Semi‐Continuous Ex Situ Carbon Dioxide Mineralization in Produced Water for Calcite Production

ABSTRACT The mineralization of carbon dioxide (CO 2 ) to stable carbonate products is a desirable process for carbon capture utilization and storage (CCUS). However, improving the process economics through creative use of available reactants is necessary to develop a scalable mineralization process. This study details the development of a semi‐continuous CO 2 mineralization process that uses flue gas as a point CO 2 source, produced water (PW) as an alkaline source of Ca 2+ , and NaOH effluent (potentially sourced from integration with the chlor‐alkali process. Operating at a controlled pH allowed for both complete reaction of available Ca 2+ (100% carbonation potential or 9.9 g CO 2 .L –1 PW brine) and for reproducible control of the produced calcium carbonate (CaCO 3 ) product. A full factorial design of experiments was implemented to study the effects of reaction temperature, pH, and gaseous CO 2 concentration on the mineralization and CO 2 capture rates as well as product crystalline structure and morphology. A maximum CO 2 capture rate of 0.315 ± 0.007 kg.L –1 .d –1 was achieved at 25°C and 25% CO 2 . CO 2 gas to liquid phase mass transport is believed to be the rate limiting step. With improved reactor design and optimization, the proposed semi‐continuous mineralization process shows promise for scaling to a pilot scale CO 2 capture technology.

Bennett, Quinn [Institute for Sustainable Energy &↗
DOE OSTI2026

Summertime methane and carbon dioxide emission rates and associated variables from a national‐scale survey of 146 reservoirs in the United States

Reservoirs are globally important sources of greenhouse gases, but the magnitude of their emissions is highly uncertain. Here, we present data for 146 reservoirs from two surveys of reservoir methane and carbon dioxide emissions, one at the regional scale in the midwestern United States and one at the national scale in the United States, plus data from two hand‐picked sites in Washington and Puerto Rico. At all reservoirs, ebullitive and diffusive emissions and basic physicochemistry were measured at 15–55 locations during one 22 to 64‐h period during the summers of 2016–2023, with four reservoirs revisited a second time. Contemporaneous water chemistry measurements were made at one or two locations in each reservoir. The dataset consists of two geospatial files and seven CSV files containing greenhouse gas emissions, water chemistry, morphology, and other relevant data. To date, these data comprise the largest multi‐reservoir emissions dataset assembled using consistent measurement methods.

Beaulieu, Jake J. [US Environmental Protection Age↗
DOE OSTI2020

Corrosion and Mechanical Performance of Grade 92 Ferritic-Martensitic Steel After Exposure to Supercritical Carbon Dioxide

Grade 92 ferritic-martensitic steel is a candidate alloy for medium temperature (< 550 °C) components for the supercritical carbon dioxide (s-CO 2 ) Brayton cycle. 1000 hours exposures were performed on base and welded material in s-CO 2 at temperatures of 450 °C or 550 °C and compared to samples aged in Ar at 550 °C. Both s-CO 2 exposures resulted in a duplex oxide growth and carburization, with 450 °C exhibiting carburization in a power law diffusion profile up to a depth of 200-250 µm, while 550 °C showed a linear profile up to a depth of 100 µm. The different profiles indicate much slower precipitation and coarsening of carbides at the lower temperature, allowing carbon to diffuse deeper into the material. However, 450 °C produced improved mechanical properties while 550 °C produced deteriorated properties. This was due to the higher density of carbon near the metal–oxide interface which leads to significant carbide coarsening and, subsequently, crack initiation and early failure. Finally, additional exposure at 450 °C is predicted to increase deposited carbon, but further study would be needed to understand if and when carburization will produce a negative mechanical effect.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Building a DFT+U machine learning interatomic potential for uranium dioxide

Despite uranium dioxide (UO 2 ) being a widely used nuclear fuel, fuel performance models rely extensively on empirical correlations of material behavior, leveraging the historical operating experience of UO 2 . Mechanistic models that consider an atomistic understanding of the processes governing fuel performance (such as fission gas release and creep) will enable a better description of fuel behavior under non-prototypical conditions such as in new reactor concepts or for modified UO 2 fuel compositions. To this end, molecular dynamics simulation is a powerful tool for rapidly predicting physical properties of proposed fuel candidates. However, the reliability of these simulations depends largely on the accuracy of the atomic forces. Traditionally, these forces are computed using either a classical force field (FF) or density functional theory (DFT). While DFT is relatively accurate, the computational cost is burdensome, especially for f-electron elements, such as actinides. By contrast, classical FFs are computationally efficient but are less accurate. For these reasons, we report a new accurate machine learning interatomic potential (MLIP) for UO 2 that provides high-fidelity reproduction of DFT forces at a similar low cost to classical FFs. We employ an active learning approach that autonomously augments the DFT training data set to iteratively refine the MLIP. To further improve the quality of our predictions, we utilize transfer learning to retrain our MLIP to higher-accuracy DFT+U data. We validate our MLIPs by comparing predicted physical properties (e.g., thermal expansion and elastic properties) with those from existing classical FFs and DFT/DFT+U calculations, as well as with experimental data when available.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Dynamic modeling of near isothermal compressor for Transcritical carbon dioxide cycle to support efficiency improvement

Compressors are the primary components of energy consumption in vapor compression systems, drawing considerable research effort to reduce carbon emissions and improve energy efficiency. This work presents an isothermal compressor that integrates the compression chamber with the gas cooler to achieve near-isothermal compression, resulting in up to 30% energy reduction compared to traditional isentropic compression, according to the experiment results. A detailed dynamic model for the isothermal compression cycle of carbon dioxide (CO 2 ) is first presented, coupled with a liquid-piston model for chamber design. The model is experimentally validated on a 3.5 kW prototype, yielding a 6.2% relative error in chamber pressure and a 0.5 K deviation in chamber temperature. The liquid piston exhibits reduced frictional heating and geometric adaptability relative to the mechanical piston. Leveraging these attributes, the study further evaluates approaches that enhance the heat transfer to achieve isothermal compression by increasing the effective heat transfer area during compression. As a result, simulations demonstrated up to a 5% improvement in the coefficient of performance over the baseline case through chamber design, providing guidelines for design of isothermal compression cycle.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Acetate-based biological platforms: Bridging carbon dioxide utilization and high-value bioproduct production in oleaginous yeasts

Acetate is emerging as a promising two-carbon substrate in the circular bioeconomy, bridging the gap between single-carbon sources and high-value biofuels and bioproducts. This review examines the key pathways for acetate production, including the electrochemical reduction of carbon dioxide, syngas fermentation, and biological acetogenesis. It focuses on acetate metabolism in oleaginous yeasts, such as Yarrowia lipolytica and Rhodotorula toruloides, which efficiently convert acetate-derived acetyl-CoA units into diverse bioproducts such as lipids, fatty alcohols, triacetic acid lactone, and carotenoids. Recent advances in metabolic engineering, transcriptomics, and metabolic flux analysis have improved the understanding of acetate assimilation in these organisms, thereby increasing their potential for industrial applications. In addition, the feasibility of a biological gas-to-liquid platform that utilizes acetate as a central intermediate for scalable biomanufacturing is discussed. Integrating acetate utilization with sustainable production strategies offers a promising path to advance the bio-based economy. Using acetate as a versatile metabolic intermediate enables the conversion of industrial emissions into biofuels and bioproducts while avoiding the energetic and toxicity constraints associated with direct fermentation of gaseous substrates.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Molecular dynamics study of carbon dioxide and nitrogen selectivity through poly[bis((methoxyethoxy)ethoxy)phosphazene] (MEEP) membrane

Here, a molecular dynamics simulation model was developed to comprehensively understand carbon dioxide over nitrogen (CO 2 /N 2 ) selectivity through polyphosphazene-based membrane comprising of poly[bis((methoxyethoxy)ethoxy)phosphazene] (MEEP) selective layer at the molecular level. The effects of temperature, pressure, and initial feed gas composition on the CO 2 transport on a polymer membrane were studied. The computed free energy and density profile of the permeating gas mixture exhibited that CO 2 molecules express higher interactions with the membrane than N 2 molecules, resulting in higher CO 2 /N 2 selectivity. Statistical analysis of gas molecules (CO 2 , water (H 2 O), and N 2 ) transportation suggested that hydro- and CO 2 -philic functional groups in the membrane significantly impact CO 2 permeability and CO 2 /N 2 selectivity. This study suggested that Lewis acid–base and hydrogen bonding combinations contribute to CO 2 permeation and CO 2 /N 2 selectivity. An equal CO 2 /N 2 selectivity was observed with and without water vapor in the feed gas suggesting that water does not hinder CO 2 transport through the membrane.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A phase-field study of stainless-steel oxidation from high-temperature carbon dioxide exposure

An electrochemical phase-field model has been developed to investigate the oxidation mechanisms of the 21-2N valve stainless steel alloy exposed to carbon dioxide at 973 K. Three oxide phases observed in oxidation experiments are included in the model: Mn 3 O 4 , Cr 2 O 3 , and MnCr 2 O 4 . Local charge neutrality and the conserved current condition are assumed to include the impact of the electric potential on oxidation, though it is found to be negligible when the system is electrically isolated. The sensitivity of the oxidation processes to the values of the diffusion mobilities is examined, and the oxidation rate is calibrated against experimental data by modifying the sensitive mobilities. We find that both inward oxygen and outward metal diffusion are important for oxidation. Furthermore, by investigating the impact of the order of the initial oxide layers, we find that Cr 2 O 3 serves as a barrier to outward Mn diffusion. Moreover, controlling the initial oxide layer order can be used to limit oxidation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Challenges of designing, operating, and managing brine extraction at a carbon dioxide storage site

Developing and deploying commercial-scale carbon dioxide (CO 2 ) storage at a site requires operational strategies to manage pressure and CO 2 plume distribution. In the natural gas storage and oil and gas industries, fluid extraction has been successfully implemented as a strategy to manage pressure and control fluid distribution (i.e., hydrocarbon recovery and natural gas storage efficiency, respectively). The technical challenges of integrating brine extraction at CO 2 storage sites are expected to be similar, if not identical, to those in the natural gas storage and petroleum industries. Major technical challenges of using brine extraction to manage storage in a storage unit include (1) designing and completing the brine extraction wells, (2) locating the brine extraction well, (3) assessing the efficacy of brine extraction, and (4) handling the extracted brine. The design and completion of the brine extraction well include the well type (i.e., vertical or horizontal) and perforated interval. The location of the well is influenced by the timing of extraction operations (i.e., prior or after CO 2 injection starts) and project objectives (i.e., desired directional movement of the CO 2 plume and avoid or minimize CO 2 extraction). The efficacy of brine extraction requires a baseline projection of the pressure and CO 2 plume distribution. Options for handling extracted brine include subsurface disposal, surface disposal, and industrial use. Here this paper addresses means of overcoming technical challenges that may likely be encountered before or after CO 2 injection starts.

25 ENERGY STORAGE↗
DOE OSTI2025

Correlation of optical properties with particle size, morphology, and polymorph of fine- and nano-particle formulations of titanium dioxide powders

Titanium dioxide (TiO 2 ) particulates are known to exhibit different visible and infrared optical properties compared to the bulk material, showing strong dependence on particle size, crystal structure, and morphology. In this study, the optical properties, sizes, and morphologies of TiO 2 particles from two different sources (nano and fine powders) having a) nominally different particle sizes and b) various crystal polymorph mixture fractions are compared using a combination of single particle mass spectrometry, optical spectroscopies, and aerosol characterization methods. The nano sample was found to be largely particles of the anatase polymorph (88% by mass), while the fine sample was found to consist largely of rutile particles (95% by mass). Two distinct particle morphologies (fractal and compact) were found in each powder sample and could be identified and separated in-situ based on particle aerodynamic properties. The attenuation of near-infrared, visible and ultraviolet light by TiO 2 particles shows strong dependence on particle morphology. Furthermore, while the fine particles were found to have larger near-infrared (675–800 nm) extinction coefficients by mass than the nanoparticles, the reverse was true in the ultraviolet and visible regions (370–675 nm). However, for polydisperse particles with different sizes and shapes, the optical behaviors are not straightforward to directly correlate to a combination of physical parameters.

Lockwood, Schuyler P. [Pacific Northwest National ↗
DOE OSTI2024

Thermal conductivity suppression in uranium-doped thorium dioxide due to phonon-spin interactions

In this work, impact of low level of uranium (U) atom substitution on thermal conductivity of thorium dioxide (ThO 2 ) is investigated. ThO 2 is an electronic insulator with a wide optical band-gap and no unpaired electrons whose thermal transport is governed by phonons. U-substitution introduces unpaired f-electrons resulting in paramagnetic behavior of U-ThO 2 at room temperature, which significantly suppresses its thermal conductivity. A single crystal of U-ThO 2 with graded composition of U is grown using a hydrothermal synthesis method, and thermal conductivity measurements are performed in regions with uniform composition of U at levels of 0%, 6%, 9% and 16%. Measured thermal conductivity profiles over 77–300 K temperature range are analyzed using an analytical expression for phonon-mediated thermal transport based on Klemens-Callaway model. Temperature dependent thermal conductivity is found to deviate significantly from the Rayleigh scattering trend expected for a simple substitutional point defect with a small perturbation to mass and interatomic forces. With the resonant scattering term, observed large suppression of thermal conductivity at low temperatures can be closely reproduced. Additionally, the extracted phonon-spin coupling constants imply a nonlinear relation of phonon-spin interaction intensity with respect to U doping percentage. Our study reveals how phonon-spin scattering contributed by unpaired f-electrons in U atoms influences thermal transport in the U-ThO 2 system.

36 MATERIALS SCIENCE↗