Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “device engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Inverted Outflow Ground Testing of Cryogenic Propellant Liquid Acquisition Devices

NASA is currently developing propulsion system concepts for human exploration. These propulsion concepts will require the vapor free acquisition and delivery of the cryogenic propellants stored in the propulsion tanks during periods of microgravity to the exploration vehicles engines. Propellant management devices (PMD's), such as screen channel capillary liquid acquisition devices (LAD's), vanes and sponges have been used for earth storable propellants in the Space Shuttle Orbiter and other spacecraft propulsion systems, but only very limited propellant management capability currently exists for cryogenic propellants. NASA is developing PMD technology as a part of their cryogenic fluid management (CFM) project. System concept studies have looked at the key factors that dictate the size and shape of PMD devices and established screen channel LADs as an important component of PMD design. Modeling validated by normal gravity experiments is examining the behavior of the flow in the LAD channel assemblies (as opposed to only prior testing of screen samples) at the flow rates representative of actual engine service (similar in size to current launch vehicle upper stage engines). Recently testing of rectangular LAD channels has included inverted outflow in liquid oxygen and liquid hydrogen. This paper will report the results of liquid oxygen testing compare and contrast them with the recently published hydrogen results; and identify the sensitivity of these results to flow rate and tank internal pressure.

Microgravity↗
NASA NTRS1940

Comparison of Three Exit-Area Control Devices on an N.A.C.A. Cowling, Special Report

Adjustable cowling flaps, an adjustable-length cowling skirt, and a bottom opening with adjustable flap were tested as means of controlling the rate of cooling-air flow through an air-cooled radial-engine cowling. The devices were tested in the NACA 20-foot tunnel on a model wing-nacelle-propeller combination, through an airspeed range of 20 to 80 miles per hour, and with the propeller blade angle set 23 degrees at 0.75 of the tip radius. The resistance of the engine to air flow through the cowling was simulated by a perforated plate. The results indicated that the adjustable cowling flap and the bottom opening with adjustable flap were about equally effective on the basis of pressure drop obtainable and that both were more effective means of increasing the pressure drop through the cowling than the adjustable-length skirt. At conditions of equal cooling-air flow, the net efficiency obtained with the adjustable cowling flaps and the adjustable-length cowling skirt was about 1% greater than the net efficiency obtained with the bottom opening with adjustable flap.

McHugh, James G.↗
NASA NTRS1974

Test techniques for obtaining off-nominal compressor data during engine tests

Several unique techniques and related devices are in use at the Lewis Research Center for off-design testing of fan and compressor sections in full-scale jet engines. The devices presented not only permit a wide range of experimental conditions but also minimize downtime for hardware changes. The techniques involve use of such devices as inlet pressure distortion jets, a hydrogen burner for inlet temperature distortions, fan back pressure jets to simulate a variable area nozzle, and either an inflow-outflow bleed system or a fuel spurt system to alter compressor discharge pressure.

Biesiadny, T. J.↗
DOE OSTI2026

Architecting the Third Dimension of Electrochemical Energy Storage

Three-dimensional (3D) architectural design has emerged as a powerful strategy to push electrochemical energy storage (EES) devices beyond the intrinsic limitations of conventional two-dimensional (2D) electrodes. While planar architectures enable high packing density and mature manufacturing, they suffer from limited ion transport and low active-material loading. In contrast, 3D architectures introduce low-tortuosity networks and high surface area that enhance charge and mass transport while supporting thick, high mass-loading electrodes. However, their practicality remains hindered by challenges in volumetric density, mechanical stability, and large-scale manufacturability. Here, this Perspective examines the key evaluation and design principles that govern 3D device performance. We discuss the fundamental trade-offs between porosity, volumetric density, and mechanical stability that shape 3D design and highlight emerging strategies for integrating materials engineering, structural optimization, device integration, computational modeling, and scalable manufacturing. By aligning structural functionality with manufacturability, 3D architectures can evolve from laboratory prototypes to commercially viable energy storage systems.

25 ENERGY STORAGE↗
NASA NTRS1974

Test techniques for obtaining off-nominal compressor data during engine tests

Several unique techniques and related devices are described which are in use at the Lewis Research Center for off-design testing of fan and compressor sections in full-scale jet engines. The devices presented permit a wide range of experimental conditions and minimize downtime for hardware changes. The techniques involve use of such devices as inlet pressure distortion jets, a hydrogen burner for inlet temperature distortions, fan back pressure jets to simulate a variable area nozzle, and either an inflow-outflow bleed system or a fuel spurt system to alter compressor discharge pressure.

Biesiadny, T. J.↗
DOE OSTI2022

Solution-Deposited and Patternable Conductive Polymer Thin-Film Electrodes for Microbial Bioelectronics

Microbial bioelectronic devices integrate naturally occurring or synthetically engineered electroactive microbes with microelectronics. These devices have a broad range of potential applications, but engineering the biotic–abiotic interface for biocompatibility, adhesion, electron transfer, and maximum surface area remains a challenge. Prior approaches to interface modification lack simple processability, the ability to pattern the materials, and/or a significant enhancement in currents. We report a novel conductive polymer coating that significantly enhances current densities relative to unmodified electrodes in microbial bioelectronics is reported. The coating is based on a blend of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) crosslinked with poly(2-hydroxyethylacrylate) (PHEA) along with a thin polydopamine (PDA) layer for adhesion to an underlying indium tin oxide (ITO) electrode. When used as an interface layer with the current-producing bacterium Shewanella oneidensis MR-1, this material produces a 178-fold increase in the current density compared to unmodified electrodes, a current gain that is higher than previously reported thin-film 2D coatings and 3D conductive polymer coatings. The chemistry, morphology, and electronic properties of the coatings are characterized and the implementation of these coated electrodes for use in microbial fuel cells, multiplexed bioelectronic devices, and organic electrochemical transistor based microbial sensors are demonstrated. It is envisioned that this simple coating will advance the development of microbial bioelectronic devices.

patterned bioelectronics↗
NASA NTRS1995

Comparison of Numerical Results and Multicavity Purge and Rim Seal Data with Extensions to Dynamics

The computation of flows within interconnected, multiple-disk cavities shows strong interaction between the cavities and the power stream. For this reason, simulations of single cavities in such cases are not realistic; the complete, linked configuration must be considered. Unsteady flow fields affect engine stability and can engender power-stream-driven secondary flows that produce local hot spotting or general cavity heating. Further, a concentric whirling rotor produces a circumferential pressure wave, but a statically eccentric whirling rotor produces a radial wave; both waves affect cavity ingestion and the stability of the entire engine. It is strongly suggested that seals be used to enhance turbojet engine stability. Simple devices, such as swirl brakes, honeycomb inserts, and new seal configurations, should be considered. The cost effectiveness of the NASA Lewis Research Center seals program can be expressed in terms of program goals (e.g., the Integrated High-pressure/Temperature Engine Technology (IHPTET) cannot be achieved without such a program), cost (savings to $250 million/1-percent decrease in specific fuel consumption), and indirect benefits (reduction of atmospheric NO(x) and CO2 and reduction of powerplant downtime).

Athavale, Mahesh↗
DOE OSTI2023

In operando cryo-STEM of pulse-induced charge density wave switching in TaS 2

The charge density wave material 1T-TaS 2 exhibits a pulse-induced insulator-to-metal transition, which shows promise for next-generation electronics such as memristive memory and neuromorphic hardware. However, the rational design of TaS 2 devices is hindered by a poor understanding of the switching mechanism, the pulse-induced phase, and the influence of material defects. Here, we operate a 2-terminal TaS 2 device within a scanning transmission electron microscope at cryogenic temperature, and directly visualize the changing charge density wave structure with nanoscale spatial resolution and down to 300 μs temporal resolution. We show that the pulse-induced transition is driven by Joule heating, and that the pulse-induced state corresponds to the nearly commensurate and incommensurate charge density wave phases, depending on the applied voltage amplitude. With our in operando cryogenic electron microscopy experiments, we directly correlate the charge density wave structure with the device resistance, and show that dislocations significantly impact device performance. This work resolves fundamental questions of resistive switching in TaS 2 devices, critical for engineering reliable and scalable TaS 2 electronics.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Engineering test procedure for the patient assist device

The test procedure completely tests the functioning of the patient assist device. All modes of operation are included in the test. Patient activated switches may be chosen for use with this device as desired. These switches, however, must be single-pole, single-throw, momentarily-on switches.

Schroder, M. A.↗
DOE OSTI2020

Power Split Supercharging: A Mild Hybrid Approach to Boost Fuel Economy

This work investigates an innovative low-voltage (<60 V) hybrid device that enables engine boosting and downsizing in addition to mild hybrid functionalities such as regenerative braking, start-stop, and torque assist. A planetary gear set and a brake permit the power split supercharger (PSS) to share a 9 kW motor between supercharging the engine and direct torque supply to the crankshaft. In contrast, most e-boosting schemes use two separate motors for these two functionalities. This single motor structure restricts the PSS operation to only one of the supercharging or parallel hybrid modes; therefore, an optimized decision making strategy is necessary to select both the device mode and its power split ratio. An adaptive equivalent consumption minimization strategy (A-ECMS), which uses the battery state of charge (SoC) history to adjust the equivalence factor, is developed for energy management of the PSS. The A-ECMS effectiveness is compared against a dynamic programming (DP) solution with full drive cycle preview through hardware-in-the-loop experiments on an engine dynamometer testbed. The experiments show that the PSS with A-ECMS reduces vehicle fuel consumption by 18.4% over standard FTP75 cycle, compared to a baseline turbocharged engine, while global optimal DP solution decreases the fuel consumption by 22.8% compared to the baseline.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Electron Spin Polarization in Large Electric Fields

This project investigated the effects of large electric fields on electron spin polarization in semiconductors, which is of interest for spin-based electronics (“spintronics”) and quantum information processing. It has been theoretically proposed that large electric fields could potentially preserve or amplify electron spin polarization, which would make it easier to generate, transport, and detect spin polarization in spin-based devices; however, previous measurements had not measured the response of electron spin polarization at large electric fields. During this project, methods to perform measurements of electron spin polarization at large electric fields were developed and performed using ultrafast time- and spatially-resolved magneto-optical spectroscopy, high-voltage pulses, and lock-in detection. The device geometry was engineered to reduce the threshold voltage required to reach the Gunn threshold, and the effect of optical illumination on the sample conductivity and Gunn oscillations was investigated. Electron spin polarization measurements were performed at electric fields up to and beyond the Gunn threshold for the device. The measurements showed that the electron spin polarization magnitude decreased with increasing electric field in the devices measured, and a spin amplification effect was not observed. However, these effects could potentially exist in a different material or in a material with a different doping concentration or in a different device geometry.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ultrafast Optomechanical Strain in Layered GeS

Strong coupling between light and mechanical strain forms the foundation for next-generation optical micro- and nano-electromechanical systems. Such optomechanical responses in two-dimensional materials present novel types of functionalities arising from the weak van der Waals bond between atomic layers. In this paper, by using structure-sensitive megaelectronvolt ultrafast electron diffraction, we report the experimental observation of optically driven ultrafast in-plane strain in the layered group IV monochalcogenide germanium sulfide (GeS). Surprisingly, the photoinduced structural deformation exhibits strain amplitudes of order 0.1% with a 10 ps fast response time and a significant in-plane anisotropy between zigzag and armchair crystallographic directions. Rather than arising due to heating, experimental and theoretical investigations suggest deformation potentials caused by electronic density redistribution and converse piezoelectric effects generated by photoinduced electric fields are the dominant contributors to the observed dynamic anisotropic strains. Our observations define new avenues for ultrafast optomechanical control and strain engineering within functional devices.

2D materials↗
NASA NTRS1996

Comparison of Non-Parabolic Hydrodynamic Simulations for Semiconductor Devices

Parabolic drift-diffusion simulators are common engineering level design tools for semiconductor devices. Hydrodynamic simulators, based on the parabolic band approximation, are becoming more prevalent as device dimensions shrink and energy transport effects begin to dominate device characteristic. However, band structure effects present in state-of-the-art devices necessitate relaxing the parabolic band approximation. This paper presents simulations of ballistic diodes, a benchmark device, of Si and GaAs using two different non-parabolic hydrodynamic formulations. The first formulation uses the Kane dispersion relationship in the derivation of the conservation equations. The second model uses a power law dispersion relation {(hk)(exp 2)/2m = xW(exp Y)}. Current-voltage relations show that for the ballistic diodes considered. the non-parabolic formulations predict less current than the parabolic case. Explanations of this will be provided by examination of velocity and energy profiles. At low bias, the simulations based on the Kane formulation predict greater current flow than the power law formulation. As the bias is increased this trend changes and the power law predicts greater current than the Kane formulation. It will be shown that the non-parabolicity and energy range of the hydrodynamic model based on the Kane dispersion relation are limited due to the binomial approximation which was utilized in the derivation.

Smith, A. W.↗
NASA NTRS2016

Band Engineering, Growth and Characteristics of Type-II InAs/GaSb Superlattice-Based Detectors

We report on band engineering, growth and device performance of infrared photodetectors based on type II InAs/Ga(In)Sb strain layer superlattices (SLs) using the complementary barrier infrared detector (CBIRD) design. The unipolar barriers on either side of the absorber in the CBIRD design in combination with the type-II InAs/GaSb superlattice material system are expected to outperform traditional III-V LWIR (Long-Wave InfraRed) imaging technologies and offer significant advantages over the conventional II-VI material based FPAs (Focal Plane Arrays). The innovative design of CBIRDS, barrier and band offset engineering , low defect density material growth, and robust fabrication processes have resulted in the development of high performance long wave infrared (LWIR) focal plane arrays at JPL (Jet Propulsion Laboratory).

Khoshakhlagh, A.↗
DOE OSTI2023

A Graph Dynamical neural network approach for decoding dynamical states in ferroelectrics.

Ferroelectric materials such as BaTiO 3 show tremendous potential for emerging advances in memory devices, particular neuromorphic type devices. High density of memory can be obtained by stabilising polar domain walls at the nanoscale, regions of discontinuity between the well-defined polarization order parameter, but little is known about what controls their structure and dynamics in real nanoscale materials. Indeed, chiral polar domain walls have been observed in heterogeneous ferroelectrics, such as oxygen-deficient BaTiO 3 , but very little is known about how such polar-domains walls interact with defects. Indeed, a critical understanding of how dynamics of domain-walls depend on point-defects is crucial to create engineered ferroelectric memory devices. For this work, we perform large-scale simulations of nansocale domain-wall dynamics in pristine and defective BaTiO 3 using reactive force-field developed by us earlier (Phys. Chem. Chem. Phys., 2019, 21, 18240–18249), and capture their dynamical dependence on point defects using a graph dynamical neural-network approach, which we adapted to interrogate solids with well-defined order-parameters, and implemented using Pytorch based libraries. Our machine learning (ML) approach goes beyond the traditional post-processing methods to capture both spatial and temporal heterogeneities of large-scale molecular dynamics simulations of complex defective ferroelectric oxide materials. We crucially find that isolated oxygen vacancies introduce very localized spatial regions (~1–2 unit-cell in length) that show slow dipole relaxation due to formation of defect-dipoles, and that these defect-dipoles in turn slow the intrinsic dynamics of domain walls. Further, the roughness of domain walls, also influenced by vacancies, introduce dynamic heterogeneity along the domain-wall. As such we find a novel mechanism by which quenched disorder due to defects introduce dynamic heterogeneity thereby influencing response to external fields (particularly time varying fields) in a ferroelectric. Our study also emphasizes the need for creating digital twins of dynamical quantities to achieve autonomous in operando control of nanoscale switching.

42 ENGINEERING↗
NASA NTRS2012

The Direction of Fluid Dynamics for Liquid Propulsion at NASA Marshall Space Flight Center

Marshall Space Flight Center (MSFC) is the National Aeronautics and Space Administration (NASA)-designated center for the development of space launch systems. MSFC is particularly known for propulsion system development. Many engineering skills and technical disciplines are needed to accomplish this mission. This presentation will focus on the work of the Fluid Dynamics Branch (ER42). ER42 resides in the Propulsion Systems Department at MSFC. The branch is responsible for all aspects of the discipline of fluid dynamics applied to propulsion or propulsion-induced loads and environments. This work begins with design trades and parametric studies, and continues through development, risk assessment, anomaly investigation and resolution, and failure investigations. Applications include the propellant delivery system including the main propulsion system (MPS) and turbomachinery; combustion devices for liquid engines and solid rocket motors; coupled systems; and launch environments. An advantage of the branch is that it is neither analysis nor test centric, but discipline centric. Fluid dynamics assessments are made by analysis, from lumped parameter modeling through unsteady computational fluid dynamics (CFD); testing, which can be cold flow or hot fire; or a combination of analysis and testing. Integration of all discipline methods into one branch enables efficient and accurate support to the projects. To accomplish this work, the branch currently employs approximately fifty engineers divided into four teams -- Propellant Delivery CFD, Combustion Driven Flows CFD, Unsteady and Experimental Flows, and Acoustics and Stability. This discussion will highlight some of the work performed in the branch and the direction in which the branch is headed.

Griffin, Lisa W.↗