SEARCH · Engineering Papers
Results for “compressed air”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Photochemically Induced Acousto-optics Fluid Simulations
PIAFS is a finite-difference code to solve the compressible Navier-Stokes equations with chemical heating on Cartesian grids. It models chemical reactions of air (oxygen and carbon dioxide) with ozone subject to radiation. It uses a high-order WENO spatial discretization and explicit Runge-Kutta time integration. It is capable of parallel simulations using MPI. The code is written in C/C++.
Fuel cells for single-aisle regional aircraft: System configuration, performance and cost
A hydrogen fuel cell propelled electric aircraft can compete with incumbent turbofan technologies for single-aisle regional aircraft by coupling design of stack, air handling, thermal management, propulsion, and airframe to optimize performance. The stack operates at 95°C to facilitate heat rejection during take-off and below 75°C during cruise to extend lifetime and is oversized to satisfy power requirements at end of life. A multi-stage turbocompressor with a compression ratio >10 is selected to reach high stack power density at 11,300-m cruise altitude. The propulsion system is configured to accommodate air handling within the core duct, an inclined heat exchanger in the outer duct to limit the nacelle size, and variable area nozzles to independently control mass flows through the core and bypass ducts. The airframe is modified for maximum lift coefficient and longer balanced field length for dramatically reduced thrust during take-off, and the fuselage is stretched by 20% to store liquid hydrogen (LH 2 ). Modularization of power systems promotes safety in one engine inoperative scenarios and allows reaching specific power metrics for stack, balance-of-plant and fuel cell system (FCS), necessary for acceptable take-off weight. In conclusion, cost parity requires increase in FCS lifetime, LH 2 cost reduction, and improved FCS specific power.
Experimental Investigation of Air-Fuel Equivalence Ratio Effects on Advanced Dual-fuel Diesel/Ammonia Combustion on a Single-Cylinder Medium-Duty Diesel Engine at High Load
Ammonia (NH3) has gathered a lot of interest as a low-lifecycle-carbon fuel in sectors with high weight and distance requirements, such as shipping. The International Maritime Organization (IMO) mandates a 70-80% greenhouse gas (GHG) reduction by 2040, which is only possible with advanced engine technologies and fuels like NH3. Prior research studies at the US Department of Energy’s Oak Ridge National Laboratory have shown strong performance with NH3 under dual-fuel mode using conventional diesel combustion (CDC) manifold air pressure (MAP) settings. Diesel airflow was initially used to simplify retrofitting (no turbocharger modification), which resulted in air-fuel equivalence ratios (λ) greater than 1.5. To characterize potential improvements in dual-fuel NH3 combustion performance at richer in-cylinder conditions, a global λ sweep using a diesel pilot ignition (DPI) strategy with diesel fuel injected near top-dead center (TDC) and a reactivity-controlled compression ignition (RCCI) injection strategy with diesel fuel injected earlier during the compression stroke were compared. The experiments were conducted at 1200 RPM and 12.6 bar (75% load), and λ was varied by decreasing the commanded air flow to the engine at greater than 90% ammonia energy substitution (AES) level. A diesel injection timing sweep was conducted for both the combustion modes at fixed λ, and the timing with the lowest engine-out N2O emissions was identified. The results indicated an optimal balance between CO2, eq and thermal efficiency benefits for both DPI and RCCI injection strategy cases compared to CDC at a λ of 1.4. The indicated N-based emissions exhibited a strong correlation to the ratio of CA5–50 and ignition delay for DPI, but no apparent trend emerged for the RCCI injection strategy at the tested boundary conditions.
Specific Ion Effects in Lanthanide–Amphiphile Structures at the Air–Water Interface and Their Implications for Selective Separation
The use of surfactants to attract dissolved ions to water surfaces and interfaces is an essential step in both solvent-based and solvent-free separation processes. Here, we have studied the interactions of lanthanide ions in the aqueous subphase with monolayers of dihexadecyl phosphate at air–water interfaces. With heavier lanthanides (atomic number Z ≥ 65) in the subphase, the floating layer can be compressed to an area/molecule of about half the molecular cross section, indicating bilayer formation. X-ray fluorescence and reflectivity data support this conclusion. In the presence of lighter lanthanides (Z < 65), only monolayers are observed. Subphase-concentration-dependent studies using Er 3+ (heavier) and Nd 3+ (lighter) lanthanides show a stepwise progression, with ions attaching to the monolayer only when the solution concentration is >3 × 10 –7 M. Above ~10 –5 M, bilayers form but only in the presence of the heavier lanthanide. Grazing incidence X-ray diffraction shows evidence of lateral ion–ion correlations in the bilayer structure but not in monolayers. Explicit solvent all-atom molecular dynamics simulations confirm the elevated ion–ion correlation in the bilayer system. This bilayer structure isolates heavier lanthanides but not lighter lanthanides from an aqueous solution and is therefore a potential mechanism for the selective separation of heavier lanthanides.
Scale-Up of Novel Li-Conducting Halide Solid State Battery Electrolyte
LBNL and project partner Saint Gobain (SG) demonstrated scalable processing of halide-based solid state batteries. SG’s innovative halide-based SSE utilized in this project is inherently scalable: it can be compressed into a dense electrolyte sheet at room temperature under moderate pressure, can be processed in dry air, and does not present any safety issues during processing or end use. The halide material forms the dense electrolyte layer, and is dispersed in the thick cathode to form a highly conductive path for Li ions. The halide also comes in contact with various environments and other materials (solvents, binders, processing equipment, etc.) throughout the battery manufacturing process, and must be stable in contact with cathode and anode materials during operation.
A wide range experimental study and further development of a kinetic model describing propane oxidation
This work presents an experimental and kinetic modeling study of propane oxidation. Ignition delay times of propane were measured in a high-pressure shock tube and in rapid compression machines in the temperature range 689 - 1700 K at equivalence ratios of 0.5, 1.0 and 2.0 in 'air', for a wide range of pressures from 20 to 90 bar. CO and H 2 O mole fraction profiles for propane oxidation were measured in a shock tube behind reflected shock waves in the temperature range 1370-1840 K at equivalence ratios of 0.5, 1.0 and 2.0 and at a pressure of approximately 1.3 atm. Moreover, propane oxidation was studied using a jet-stirred reactor coupled to a synchrotron vacuum ultraviolet photoionization mass spectrometer at low temperatures in the range 565 - 690 K and at a pressure of 1 atm. Further, this wide range of experimental datasets for propane oxidation was used to reoptimize and update our previous kinetic mechanisms, AramcoMech3.0 and NUIGMech1.1. In the current mechanism, NUIGMech1.3, the thermo-chemical parameters of all species relevant to low-temperature propane oxidation chemistry, including propyl-peroxyl, hydroperoxyl-propyl, hydroperoxyl-propyl-peroxyl, and carbonyl-hydroperoxide radicals, are updated based on newly calculated values at the CCSD(T)-F12/TZ-F12//B2PLYPD3/TZ///B2PLYP-D3/TZ level of theory. The improvements made in the thermochemical values and in the kinetic parameters for the low-temperature propane oxidation reactions in NUIGMech1.3 result in better model agreement with the new IDTs and speciation data, including carbon monoxide, formaldehyde, propene, acetaldehyde and various minor products such as ethylene, acetic acid, acrolein as well as various hydroperoxide and cyclic ether species.
Low soot stoichiometric compression-ignition combustion
A combustion system including a combustion mechanism that injects oxygenated fuel into a combustion chamber. The oxygenated fuel mixes with the intake air in the combustion chamber where the air-fuel ratio in a portion of the combustion chamber is stoichiometric. The combustion mechanism includes an ignition mechanism that ignites the air-fuel mixture that generates a threshold number of particulates during combustion of the air-fuel mixture. The combustion system further includes an exhaust gas recirculation (EGR) device that recirculates a portion of the exhaust gases back into the combustion chamber. The EGR device recirculates the portion of the exhaust to lower combustion temperature resulting in reduced amount of nitrogen oxide in the exhaust. The combustion system further includes a three-way catalytic converter in line with the exhaust channel to convert a second portion of the exhaust gases, leading to lower pollutant emissions than conventional combustion systems.
An experimental and detailed kinetic modeling study of the pyrolysis and oxidation of allene and propyne over a wide range of conditions
Allene and propyne are important intermediates in the pyrolysis and oxidation of higher hydrocarbon fuels, and they are also a major source of propargyl radical formation, which can recombine into different C 6 H 6 isomers and finally produce soot. In a prior work (Panigrahy et al., “A comprehensive experimental and improved kinetic modeling study on the pyrolysis and oxidation of propyne”, Proc. Combust. Inst 38 (2021)), the pyrolysis, ignition , and laminar flame speed of propyne were investigated. To understand the kinetic features of initial fuel breakdown and oxidation of the two C 3 H 4 isomers, new measurements for allene pyrolysis and oxidation are conducted in the present paper at the same operating conditions as those studied previously for propyne. Ignition delay times of allene are measured using a high-pressure shock tube and a heated twin-opposed piston rapid compression machine in the temperature range 690– 1450 K at equivalence ratios of 0.5, 1.0 and 2.0 in ‘air’, and at pressures of 10 and 30 bar. Pyrolysis species measurements of allene and propyne are also performed using a gas chromatography integrated singlepulse shock tube in the temperature range 1000–1700 K at pressure of 2 and 5 bar. Furthermore, laminar flame speeds of allene are measured at elevated gas temperatures of 373 K at pressures of 1 and 2 bar for a wide range of equivalence ratios from 0.6 to 1.5. A newly updated kinetic mechanism developed for this study is the first model that can well reproduce all of the experimental results for both allene and propyne. It is observed that in the pyrolysis process, allene dissociates faster than propyne. Both isomers exhibit similar ignition delay times at high temperatures (>1000 K), while, at intermediate temperatures (770–1000 K) propyne is the faster to ignite, and at lower temperatures (< 770 K) allene becomes more reactive. Furthermore, laminar flame speeds for propyne are found to be slightly faster than those for allene under the conditions studied in this work
Experimental and Kinetic Modeling Study of 3-Methyl-2-butenol (Prenol) Oxidation
Longer chain alcohols with 4–5 carbon atoms are attractive alternative fuels as they can be derived from biological sources and since their combustion leads to lower exhaust gas levels of NO x and soot compared to commercial fossil fuels. The auto-ignition behavior of fuels that contain both a hydroxyl group and a C=C double bond in their molecular structure is not well established in the literature. Understanding the influence of these functional groups on the ignition behavior of fuels is critical in the development of tailor-made fuels for advanced combustion engines. In this study, ignition delay times of an unsaturated alcohol, 3-methyl-2-butenol (prenol), are measured using a high-pressure shock tube and a rapid compression machine at pressures of 15 and 30 bar at equivalence ratios of 0.5, 1.0, and 2.0 in “air” in the temperature range 600–1400 K. Furthermore, a detailed kinetic model is developed and validated using the new experimental data in this study. In addition, speciation data in a jet-stirred reactor, ignition delay times, and laminar burning velocities available in the literature were also used to validate the new kinetic model. Fuel flux and sensitivity analyses are performed using this new model to determine the important fuel consumption pathways and critical reactions that affect the reactivity of prenol.
RapidClave® Technology Demonstrations - I
This demonstration sought to show a dramatic reduction in tool cost for RapidClave® tooling, taking advantage of recent modifications made on the RapidClave® system. Instead of building tools with complex internal heating, simple aluminum tools would be produced and heated externally through the recently added hot plate and air blower inside the RapidClave® system. Baselining against this tooling is the legacy RapidClave® tooling, as well as compression tooling, which would be the incumbent processing technique that the RapidClave® is displacing. Both an automotive and aerospace application were used to evaluate the tooling and process. Specifically, a four-piece Volkswagen hood structure was selected as an appropriate automotive geometry, while a wing structure representative of a current wing entering limited production was provided by Cornerstone Research Group for evaluating aerospace applications. In total, six tools were fabricated, and costs were compared against compression tooling quotes of the same tool geometry. A cost savings of over 80% was shown on all the tools. This demonstration also produced parts in the RapidClave® using the abovementioned tools to validate the low-cost tooling and the machine modifications. Solvay recommended two prepreg systems, CYCOM® EP2750 and SolvaLite™ 712, as appropriate for aerospace and automotive applications, respectively. Flat panels of each material were fabricated to verify cure parameters before proceeding with actual part fabrication. On-tool cycle times of approximately 30 minutes was achieved, with modifications identified to lower the time further.
INVESTIGATION OF TURBULENT JETS, SPRAYS, AND SUPERCRITICAL MIXING BY TIME RESOLVED RAINBOW SCHLIEREN DEFLECTOMETRY
As technological advancements have enabled higher efficiency compression ignition (CI) engines (diesel engines) by operating at higher pressures and temperatures, the mechanisms of fuel-air mixing are postulated to change. Thus, there is a greater need for experimental data to develop and verify new phenomena. However, the fast time scales and harsh environments associated with CI engines present many experimental difficulties and requires high quality non-intrusive diagnostics to obtain useful data. The diagnostics itself must be validated prior to its implementation in an engine environment. The purpose of this research is to advance rainbow schlieren deflectometry (RSD) to study turbulent fuel sprays including the effects of supercritical mixing in CI engine environments. This objective is met by developing and applying quantitative RSD, for the first time, to three separate aspects of fuel sprays: 1) turbulent mixing, 2) phase boundaries, and 3) non-ideal gas mixing. First, quantitative RSD is demonstrated for turbulent mixing in a canonical helium jet. Rayleigh scattering data in the literature is used to validate the concentration measurements obtained by RSD. The results also provide explanations for phenomena occurring in the helium jet and provide data not yet present in the literature. Second, RSD is applied to high pressure multi-phase fuel sprays and new methodologies are developed to distinguish the liquid region from the vapor region and to quantify the in-between region on a probabilistic basis. Isolating liquid and vapor regions generally requires two separate diagnostics, e.g., Mie scattering (liquid region) and Rayleigh scattering (vapor region). However, the results of this study demonstrate that RSD can be used as a single diagnostic to measure both liquid and vapor boundaries. Third, the optical-to-thermodynamic relations associated with refrac-tometry are investigated under non-ideal gas mixing conditions to develop a generalized relationship valid for both ideal or non-ideal gas mixing. The last part of this research develops the theoretical tools to understand and experimentally realize supercritical mixing at diesel conditions. Guided by the theoretical analysis, RSD is applied to compare supercritical versus transcritical mixing at CI conditions using a constant pressure test rig. It is found that while fully supercritical mixing ers benefits in diesel engines, i.e, faster mixing times (50% higher velocities), the absence of droplets which cause high levels of particulate emissions, etc., it would be difficult to achieve in practice because of the requirements of fuels with low critical temperature and/or substantial fuel preheating.
Improving AHU Performance by Minimizing Approach Temperature, Reducing Air Maldistribution, and Efficiently Handling Sensible and Latent Loads (Phase 1 Interim Final Technical Report)
Residential air handling units (AHUs) have stayed the same in form and efficiency for the past 30+ years, with incremental improvements made to address safety, functionality, and energy-efficiency. The purpose of this research in Phase I, Topic 9a: Next Generation Residential Air Handlers, was to improve AHU performance by minimizing heat exchanger (HX) approach temperature, reducing air maldistribution, and developing alternative system configurations which more efficiently handle sensible and latent loads. In this research Optimized Thermal Systems (OTS) developed, modeled, and evaluated multiple alternative system concepts. A dual vapor compression system separate sensible and latent cooling (SSLC) concept was studied to inform work on alternative concepts and to show best-case performance benefit. System concepts included ejector enhanced vapor compression cycles, desiccant assisted dehumidification, dual evaporator SSLC, and alternative AHU HX configurations. A dual vapor compression system showed COP improvement of 20%, however, required additional components, increased unit size, and increased cost. Two types of ejector enhanced vapor compression cycles with dual evaporators improved system COP by 9 to 11%, and reduced AHU losses by as much as 18%, with design changes limited to the AHU, no unit physical size increase, and a moderate increase to system first cost. Desiccant assisted air-conditioning required increased air flow rate resulting in higher fan power and the desiccant wheel increased sensible heat load leading to increased compressor power and reduced system COP. Dual evaporator cycles were found to degrade performance due to increased expansion losses. Optimized single slab HX designs used in place of the traditional A-coil HX led to 44–49% reduction in aluminum, 47–60% less refrigerant charge, and improved HX velocity distribution.
Virtual Pressure Sensor for Electronic Expansion Valve Control in a Vapor Compression Refrigeration System
Virtual sensor technology, which uses simulation models/algorithms to calculate a value to represent an unmeasured variable or replace a directly measured reading, has attracted many studies in the heating, ventilation, air conditioning and refrigeration (HVAC&R) industry. However, most virtual sensor technologies are developed for fault detection and diagnostics (FDD) purposes, which generally compare the virtual sensor values with actual measured values to detect if any fault occurred and identify the causes that led to the fault. It is rare to see studies focus on control performance of virtual sensors after substituting an actual sensor. This is particularly important for the system with no redundant sensor since a virtual sensor is the most effective way to operate the system in the desirable region when any sensor failure occurs. To address this gap, this paper develops a new virtual pressure sensor technology to substitute the actual pressure measurement for electronic expansion valve (EXV) control in a vapor compression refrigeration system by integrating compressor and valve characteristics. The control performance of this proposed virtual pressure sensor technology under various operating conditions is validated with experimental data. Closed loop EXV control simulations with the proposed virtual pressure sensor are conducted, and the results are analyzed.
Development of Two-Phase Dense Fluid Expander for Advanced Cryogenic Air Separation and Low-Grade Heat Recovery
Cryogenic air separation represents the state-of-the-art technology to produce oxygen to feed coal gasification units. Given the maturity of this technology, it is difficult to identify opportunities to improve process efficiency and reduce the cost of the oxygen produced. However, Air Products conducted research and a feasibility investigation into the use of a two-phase (liquid-vapor) dense fluid expander (DFE) to improve the overall efficiency of cryogenic air separation. Demonstration of this novel concept was intended to allow two important process improvements: 1) elimination of the need for the DFE discharge to be single phase 2) expansion of the operating region of expanders in ASU service. Expanding the scope of turboexpander application beyond current application limits and traditional device designs would allow an increase in power recovery, and application of refrigeration and power recovery at new locations in process cycles would also enable the implementation of new process concepts. These new process concepts include power recovery from compression waste heat and refrigeration extraction and power recovery by replacing let-down valves with two-phase DFEs. Considering the maturity of cryogenic air separation, these new process options could represent a step change in power reduction and provide significant savings in operating costs. These new concepts would be particularly well-suited to large-scale oxygen production by cryogenic air separation and would enhance the economics of producing oxygen for use in coal gasification processes. Rotoflow, an Air Products business unit, manufactures dense fluid expanders in Pennsylvania for sites around the world. This project was executed in two phases, which are illustrated in Figure 1 below. Phase 1 consisted of a feasibility investigation of multiple applications of two-phase DFEs. In Phase 2, devices were identified, designed, fabricated and tested to explore the feasibility of commercial applications of DFEs operating in two-phase service. Engineering and testing were performed by personnel in Air Products’ Rotoflow business unit, with coordination with other Air Products business units.
Enhancing $\phi$-sensitivity of ignition delay times through dilution of fuel-air mixture
The high $\phi$-sensitivity (η) of ignition delay time (τ IDT ) is one of the desirable fuel properties for the high-load extension of advanced compression ignition engine. Recent studies revealed the effectiveness of a high dilution rate (x D ) for enhancing η at the engine-relevant conditions. This study aims to quantify the effect of dilution on the η of isooctane using a combined experiment-simulation approach. The ignition delay of the isooctane/air mixture was measured with an Advanced Fuel Ignition Delay Analyzer (AFIDA) over the temperature range of 623 - 923 K at 10 bar pressure with global $\phi$ = 0.3 - 0.6, with and without 28.6% of additional N 2 dilution. For precise evaluation of experimental η, the facility effect of the AFIDA experiment was characterized with three-dimensional computational fluid dynamics (3-D CFD) simulation. The temperature in the combustion chamber from 3-D CFD indicated a substantial temporal dependency, varying up to ~52 K by charge-cooling of fuel injection and heat transfer from the wall. We introduced the dimensionless number θ(t) for characterizing the temporal profile of chamber temperature. Consideration of the facility effect using θ(t) resulted in better agreement between the experimental ..eta.. and zero-dimensional (0-D) kinetics simulation. The refined η were then further utilized to quantify the effectiveness of dilution to η The extent of η enhancement with dilution strategy was maximized at the low-temperature chemistry regime, increasing η by 77% with a 28.6% dilution rate. Further analysis on the dilution effect was carried out using 0-D kinetics simulation, revealing the critical dimensionless numbers relevant to the effectiveness of dilution to η enhancement. Here, this study is the first experiment-simulation combined research to quantify the effect of dilution on η, facilitating the kinetics model refinement for better reproduction of $\phi$-sensitivity.
Modeling of shock-induced force on an isolated particle in water and air
The prediction of force on an isolated particle, while a shock is passing over it, is an important problem in many natural and industrial applications. Although the flow monotonically changes from the pre-shock to the post-shock state, the particle's force has been observed to behave nonmonotonically with a sharp peak when the shock is located halfway across the particle. This nonmonotonic behavior is due to the unsteady nature of the compression and rarefaction waves that radiate as the shock diffracts around the particle and, therefore, cannot be predicted by a quasi-steady model. An accurate force model must account for the unsteady nature of the flow and the sharp discontinues in the flow properties across the shock. In this work, we test four different inviscid models and observe that the compressible Maxey–Riley–Gatignol (C-MRG) model is the most accurate based on comparison with results from particle-resolved inviscid simulations at two different Mach numbers for both water and air as the medium. The C-MRG model is first demonstrated to predict the force on a stationary particle accurately and then extended to capture the force on a moving particle. Numerical complexities regarding the implementation of the C-MRG model are also discussed.
Numerical Investigation of Two-Stage Vapor Compression System with Simultaneous Vapor and Liquid Injection
Two-stage vapor compression systems can be advantageous over single-stage systems by providing improved system performance, lower discharge temperature and reduced throttling losses. These systems employ various intermediate configurations, such as liquid injection and vapor injection. This paper presents a configuration for a R1234ze(E) two-stage air-conditioning system using a turbo compressor with two injection ports, one for vapor injection and the second for liquid injection. The liquid injection is used to cool the motor and electronics. A component-based representation and solution approach was used to simulate the two-stage compression system with simultaneous vapor and liquid injection at steady state. The turbo compressor was represented using a customized performance map. The condenser and the evaporator were modeled using finite-volume approach. A parametric study was conducted to assess the impact of the following three variables on the system performance: vapor injection ratio, condenser air flow rate, and discharge pipe pressure drop. The simulation results show that as the vapor injection ratio increased, the system performance undergoes a tradeoff between an enhanced subcooling effect (and thus enhanced unit refrigeration capacity) and a decreased suction mass flow rate. Maximum COP occurs when the vapor injection ratio was 0.1. The results also show that as the condenser air flow rate increased, both the capacity and power consumption (including fan power) increased monotonically, and COP increased first and then decreased. At 75% load, the COP improvement at the optimum flow rate was marginally less than 0.5%. Lastly, higher discharge pipe pressure drop increased the discharge pressure. It showed very small effect on the overall system performance at the condition selected for the current study.