A note on frequency modulation spectra.
FM spectra proved to be not band limited, using Fourier transform of Hess equation to obtain second order convolution equation
Yavuz, D.↗
SEARCH · Engineering Papers
Results for “band modulation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Radar RFI at Goldstone DSS 12 and DSS 16
Radio frequency interference (RFI) from the DSS 14 Goldstone Solar System Radar (GSSR) was investigated at DSS 12 and DSS 16 with the goal of assisting in the choice of the location of future DSN antennas. Total power measurements at both locations were made at the S-band carrier frequency of 2320 MHz. X-band measurements at the carrier frequency of 8495 MHz could not be made. Exciter-chain output spectrum and klystron output spectrum measurements were made at S- and X-bands using a probable worst-case modulation of the radar signal (short pseudorandom number (PN) code length and short pulse length). Based on these measurements, it is estimated that RFI levels in the DSN receiving bands at both sites (above 10-deg elevation) would be below -192 dBm for a 1-Hz bandwidth
Slobin, S. D.↗
A Study of the Kinematic and Dynamic Processes associated with Mesoscale Snowbands in a Midwest United States Snowstorm on 5 February 2020
Mesoscale snowbands are frequently responsible for dumping large amounts of snow over a relatively small region and pose a considerable forecasting challenge. The present study focuses on the mesoscale snowbands observed on 5 February 2020 over the Midwest United States. In order to improve the forecasting of mesoscale snowbands, it is important to understand the processes that organize these features. To this end, we are investigating the kinematic and dynamic processes that shape the mesoscale snowbands using a combination of high-altitude airborne radar, in-situ aircraft measurements, surface observations, and model simulations. This presentation will primarily focus on the three-dimensional structure of the mesoscale snowbands in terms of EXRAD reflectivity and horizontal winds. The horizontal winds are retrieved from the EXRAD scanning-beam Doppler velocities using a VAD technique. These winds, in combination with virtual potential temperature taken from the HRRR operational analysis, are used to compute the bulk Richardson number in order to investigate any contributions to banding features that might be tied to Kelvin-Helmholtz instability. Our analysis does not support the presence of Kelvin-Helmholtz instability. That said, low, but not subcritical, Richardson numbers were found near the top of some banding features in this event and it is possible that the model analysis is smoothing out the virtual potential temperature fields. Finally, we present arguments for using a flight module designed to sample the along-band structures with particular emphasis on observing generating cells and low-level microphysics.
Charles N. Helms↗
Ka-band active MMIC subarray development
A 4 x 8 array consisting of two adjacent 4 x 4 MMIC subarray modules under development as part of a MMIC insertion program for the ACTS communication experiments is presented. The subarray features a high-density 'tile' configuration integrating 16 MMIC power amplifiers and 16 MMIC phase shifters. The radiating elements are cavity-backed, aperture coupled, linearly polarized microstrip patches arranged on a 4 x 4 square grid. Each module also incorporates a MMIC controller to set the phase shifts and to turn individual amplifiers 'on' or 'off'. The novel module construction technique is expected to establish a benchmark in Ka-band and higher-frequency array architectures. The hybrid integration approach used for the module can be replaced by multifunctional chips and multilayer distribution boards. The higher level of integration is to permit the dense grid spacing required for wide-angle scanning and reduced size, weight, and cost for the array.
Lee, Richard↗
System and method for progressive band selection for hyperspectral images
Disclosed herein are systems, methods, and non-transitory computer-readable storage media for progressive band selection for hyperspectral images. A system having module configured to control a processor to practice the method calculates a virtual dimensionality of a hyperspectral image having multiple bands to determine a quantity Q of how many bands are needed for a threshold level of information, ranks each band based on a statistical measure, selects Q bands from the multiple bands to generate a subset of bands based on the virtual dimensionality, and generates a reduced image based on the subset of bands. This approach can create reduced datasets of full hyperspectral images tailored for individual applications. The system uses a metric specific to a target application to rank the image bands, and then selects the most useful bands. The number of bands selected can be specified manually or calculated from the hyperspectral image's virtual dimensionality.
Fisher, Kevin↗
Delta modulation
The conclusions of the design research of the song adaptive delta modulator are presented for source encoding voice signals. The variation of output SNR vs input signal power/when 8, 9, and 10 bit internal arithmetic is employed. Voice intelligibility tapes to test the 10-bit system are used. An analysis of a delta modulator is also presented designed to minimize the in-band rms error. This is accomplished by frequency shaping the error signal in the modulator prior to hard limiting. The result is a significant increase in the output SNR measured after low pass filtering.
Schilling, D. L.↗
NASA Tech Briefs, March 2010
Topics covered include: Software Tool Integrating Data Flow Diagrams and Petri Nets; Adaptive Nulling for Interferometric Detection of Planets; Reducing the Volume of NASA Earth-Science Data; Reception of Multiple Telemetry Signals via One Dish Antenna; Space-Qualified Traveling-Wave Tube; Smart Power Supply for Battery-Powered Systems; Parallel Processing of Broad-Band PPM Signals; Inexpensive Implementation of Many Strain Gauges; Constant-Differential-Pressure Two-Fluid Accumulator; Inflatable Tubular Structures Rigidized with Foams; Power Generator with Thermo-Differential Modules; Mechanical Extraction of Power From Ocean Currents and Tides; Nitrous Oxide/Paraffin Hybrid Rocket Engines; Optimized Li-Ion Electrolytes Containing Fluorinated Ester Co-Solvents; Probabilistic Multi-Factor Interaction Model for Complex Material Behavior; Foldable Instrumented Bits for Ultrasonic/Sonic Penetrators; Compact Rare Earth Emitter Hollow Cathode; High-Precision Shape Control of In-Space Deployable Large Membrane/Thin-Shell Reflectors; Rapid Active Sampling Package; Miniature Lightweight Ion Pump; Cryogenic Transport of High-Pressure-System Recharge Gas; Water-Vapor Raman Lidar System Reaches Higher Altitude; Compact Ku-Band T/R Module for High-Resolution Radar Imaging of Cold Land Processes; Wide-Field-of-View, High-Resolution, Stereoscopic Imager; Electrical Capacitance Volume Tomography with High-Contrast Dielectrics; Wavefront Control and Image Restoration with Less Computing; Polarization Imaging Apparatus; Stereoscopic Machine-Vision System Using Projected Circles; Metal Vapor Arcing Risk Assessment Tool; Performance Bounds on Two Concatenated, Interleaved Codes; Parameterizing Coefficients of a POD-Based Dynamical System; Confidence-Based Feature Acquisition; Algorithm for Lossless Compression of Calibrated Hyperspectral Imagery; Universal Decoder for PPM of any Order; Algorithm for Stabilizing a POD-Based Dynamical System; Mission Reliability Estimation for Repairable Robot Teams; Processing AIRS Scientific Data Through Level 3; Web-Based Requesting and Scheduling Use of Facilities; AutoGen Version 5.0; Time-Tag Generation Script; PPM Receiver Implemented in Software; Tropospheric Emission Spectrometer Product File Readers; Reporting Differences Between Spacecraft Sequence Files; Coordinating "Execute" Data for ISS and Space Shuttle; Database for Safety-Oriented Tracking of Chemicals; Apparatus for Cold, Pressurized Biogeochemical Experiments; Growing B Lymphocytes in a Three-Dimensional Culture System; Tissue-like 3D Assemblies of Human Broncho-Epithelial Cells; Isolation of Resistance-Bearing Microorganisms; Oscillating Cell Culture Bioreactor; and Liquid Cooling/Warming Garment.
Source record↗
A superconducting time-variant filtering system.
Description of a laboratory test facility for studying the tracking capabilities of a superconducting time-varying filter system. An RF signal from an antenna is amplified and fed to a mixer; the IF signal modulates an optical diode, and the emitted light is directed through an optical system onto a high-purity high-resistance semiconductor terminating a quarter-wavelength stub in a lead-plated superconducting cavity. The resulting perturbation in the cavity resonant frequency is proportional to the signal modulation present in the light beam. The narrow-band superconducting cavity is thereby acting as a time-variant filter that tracks the instantaneous signal modulation. SNR improvement on the order of 25 dB can be obtained due to the noise rejection characteristics of such a modulation tracking filter.
Arndt, G. D.↗
Cryogenic 160-GHz MMIC Heterodyne Receiver Module
A cryogenic 160-GHz MMIC heterodyne receiver module has demonstrated a system noise temperature of 100 K or less at 166 GHz. This module builds upon work previously described in Development of a 150-GHz MMIC Module Prototype for Large-Scale CMB Radiation (NPO-47664), NASA Tech Briefs, Vol. 35, No. 8 (August 2011), p. 27. In the original module, the local oscillator signal was saturating the MMIC low-noise amplifiers (LNAs) with power. In order to suppress the local oscillator signal from reaching the MMIC LNAs, the W-band (75 110 GHz) signal had to be filtered out before reaching 140 170 GHz. A bandpass filter was developed to cover 120 170 GHz, using microstrip parallel-coupled lines to achieve the desired filter bandwidth, and ensure that the unwanted W-band local oscillator signal would be sufficiently suppressed. With the new bandpass filter, the entire receiver can work over the 140 180-GHz band, with a minimum system noise temperature of 460 K at 166 GHz. The module was tested cryogenically at 20 K ambient temperature, and it was found that the receiver had a noise temperature of 100 K over an 8-GHz bandwidth. The receiver module now includes a microstrip bandpass filter, which was designed to have a 3-dB bandwidth of approximately 120-170 GHz. The filter was fabricated on a 3-mil-thick alumina substrate. The filter design was based on a W-band filter design made at JPL and used in the QUIET (Q/U Imaging ExperimenT) radiometer modules. The W-band filter was scaled for a new center frequency of 150 GHz, and the microstrip segments were changed accordingly. Also, to decrease the bandwidth of the resulting scaled design, the center gaps between the microstrip lines were increased (by four micrometers in length) compared to the gaps near the edges. The use of the 150-GHz bandpass filter has enabled the receiver module to function well at room temperature. The system noise temperature was measured to be less than 600 K (at room temperature) from 154 to 168 GHz. Additionally, the use of a W-band isolator between the receiver module and the local oscillator source also improved the noise temperature substantially. This may be because the mixer was presented with a better impedance match with the use of the isolator. Cryogenic testing indicates a system noise temperature of 100 K or less at 166 GHz. Prior tests of the MMIC amplifiers alone have resulted in a system noise temperature of 65.70 K in the same frequency range (.160 GHz) when cooled to an ambient temperature of 20 K. While other detector systems may be slightly more sensitive (such as SIS mixers), they require more cooling (to 4 K ambient) and are not as easily scalable to build a large array, due to the need for large magnets and other equipment. When cooled to 20 K, this receiver module achieves approximately 100 K system noise temperature, which is slightly higher than single-amplifier module results obtained at JPL (65.70 K when an amplifier is corrected for back-end noise contributions). If this performance can be realized in practice, and a scalable array can be produced, the impact on cosmic microwave background experiments, astronomical and Earth spectroscopy, interferometry, and radio astronomy in general will be dramatic.
Samoska, Lorene A.↗
Advanced tracking and data relay experiments study: Multimode transponder experiment equipment
Plans and implementation concepts were developed for a series of experiments utilizing a Multimode Transponder mounted in an aircraft working either through a spacecraft or directly with a ground station which would simulate a TDRSS user working through the TDRSS. The purpose of the experiments is to determine the best modulation and encoding techniques for combating RFI in discreet bands. The experiments also determine the feasibility and accuracy of range and range rate measurements with the various modulation and encoding techniques. An analysis of the Multimode Transponder and ground support equipment is presented, and the additional equipment required to perform the experiments described above is determined.
Cnossen, R. S.↗
Data handling and control of the Mariner Venus Mercury '73 spacecraft
Data handling and control subsystems are described for the MVM73 spacecraft, which demonstrated the feasibility of multiple-planet gravity-assist missions. In spite of strict budgetary constraints, MVM73 carried out experiments utilizing television, an IR radiometer, a UV spectrometer, a fluxgate magnetometer, a charged particle telescope, a modulation-demodulation unit, an X-band and S-band dual frequency communications system, a steerable high-gain antenna, a time-sharing digital articulation and pointing system, and moveable solar panels. The trajectory design and flight data system are described, and the systems governing articulation and pointing and attitude control are discussed.
Scull, J. R.↗
Evaluation of the JPL X-band 32 element active array
Tests performed on an X-band 32-element active array are described. Antenna pattern characteristics of the array were tested in its standard operating mode as well as several degraded performance modes, including failures of 1, 2, 3, 4, 8, 16, and 31 elements. Additionally, the array was characterized with the addition of a metallic shroud, and also characterized versus rf drive level and at a single off-axis electronic beamsteered position. Characterization was performed on several of the 3/4-watt, three-stage, X-band solid-state power amplifier modules. The characterization included swept amplitude response, amplitude and phase versus temperature from -20 to +60 C, and intermodulation distortion of selected modules. The array is described and conclusions and recommendations based upon the experience and results achieved are included.
Boreham, J. F.↗
Stepanyan's star - A new eclipsing cataclysmic variable
High-speed photometry of the nova-like variable Stepanyan's star shows a 3-hr 48-min orbital period marked by a 2.2-mag eclipse which spans orbital phases 0.91-0.09. The uneclipsed light is variable by typically 0.15 mag on time scales of minutes to seconds and shows no obvious modulation with orbital phase. Intermediate-band colors show an enhancement in Balmer continuum emission and in red light during the eclipse.
Horne, K.↗
The payload/shuttle-data-communication-link handbook
Communication links between the Orbiter, payloads, and ground are described: end-to-end, hardline, S-band, Ku-band, TDRSS relay, waveforms, premodulation, subcarrier modulation, carrier modulation, transmitter power, antennas, the RF channel, system noise, received signal-to-noise spectral density, carrier-tracking loop, carrier demodulation, subcarrier demodulation, digital data detection, digital data decoding, and tandem link considerations.
Source record↗
Resonant Third-Degree Diurnal Tides in the Seas Off Western Europe
Third-degree diurnal tides are estimated from long time series of sea level measurements at three North Atlantic tide gauges. Although their amplitudes are only a few mm or less, their admittances are far larger than those of second-degree diurnal tides, just as Cartwright discovered for the M(sub 1) constituent. The tides are evidently resonantly enhanced owing to high spatial correlation between the third-degree spherical harmonic of the tidal potential and a near-diurnal oceanic normal mode that is most pronounced in the North Atlantic. By estimating the ocean tidal response across the diurnal band (5 tidal constituents plus nodal modulations), the period and Q of this mode and one nearby mode are estimated.
Ray, Richard D.↗
The QUIET Instrument
The Q/U Imaging ExperimenT (QUIET) is designed to measure polarization in the Cosmic Microwave Background, targeting the imprint of inflationary gravitational waves at large angular scales ( approx 1 deg.) . Between 2008 October and 2010 December, two independent receiver arrays were deployed sequentially on a 1.4 m side-fed Dragonian telescope. The polarimeters which form the focal planes use a highly compact design based on High Electron Mobility Transistors (HEMTs) that provides simultaneous measurements of the Stokes parameters Q, U, and I in a single module. The 17-element Q-band polarimeter array, with a central frequency of 43.1 GHz, has the best sensitivity (69 micro Ks(exp 1/2)) and the lowest instrumental systematic errors ever achieved in this band, contributing to the tensor-to-scalar ratio at r < 0.1. The 84-element W-band polarimeter array has a sensitivity of 87 micro Ks(exp 1/2) at a central frequency of 94.5 GHz. It has the lowest systematic errors to date, contributing at r < 0.01 (QUIET Collaboration 2012) The two arrays together cover multipoles in the range l approximately equals 25-975 . These are the largest HEMT-ba.sed arrays deployed to date. This article describes the design, calibration, performance of, and sources of systematic error for the instrument,
Gaier, T.↗
Performance Analysis of a Hardware Implemented Complex Signal Kurtosis Radio-Frequency Interference Detector
In the field of microwave radiometry, Radio Frequency Interference (RFI) consistently degrades the value of scientific results. Through the use of digital receivers and signal processing, the effects of RFI on scientific measurements can be reduced depending on certain circumstances. As technology allows us to implement wider band digital receivers for radiometry, the problem of RFI mitigation changes. Our work focuses on finding a detector that outperforms real kurtosis in wide band scenarios. The algorithm implemented is a complex signal kurtosis detector which was modeled and simulated. The performance of both complex and real signal kurtosis is evaluated for continuous wave, pulsed continuous wave, and wide band quadrature phase shift keying (QPSK) modulations. The use of complex signal kurtosis increased the detectability of interference.
microwaves↗
Preliminary Evaluation of Thematic Mapper Image Data Quality
Thematic Mapper (TM) data from Mississippi County, Arkansas, and Webster County, Iowa, were examined for the purpose of evaluating the image data quality of the TM which was launched on board the LANDSAT-4 spacecraft. Preliminary clustering and principal component analysis indicates that the middle infrared and thermal infrared data of TM appear to add significant information over that of the near IR and visible bands of the multispectral scanner data. Moreover, the higher spatial resolution of TM appears to provide better definition of the edges and the within variability of agricultural fields. The geometric performance of TM data, without ground control correction, was found to exceed expectations. The modulation transfer function for the 1.65 m band was found to agree with prelaunch specifications when the effects of the GSFC cubic convolution and the atmosphere were removed. The band to band registration for the bands within the noncooled focal plane was found to be better than specified. However, the middle infrared and thermal infrared, which are on a separate cooled focal plane were found to be misregistered and were significantly worse than prelaunch specifications.
Macdonald, R. B.↗