Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “analog control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

A roll-pitch interaction simulator and a control position command encoder for remote piloting of spin-entry research models

The Langley Research Center uses radio-controlled, scaled aircraft models to study the spin-entry characteristics of aircraft. Recent spin-entry studies required the use of an electronic proportional-control system for manipulating model control surfaces. In order to meet control system requirements, a special-purpose analog computer was designed to simulate the coupling between roll and pitch controls. A digital encoder was designed to encode the voltage analogs of control-surface position into a special pulse format for transmission to the model. This paper describes the two special developments and their relationship to the functions of the overall control system.

Meissner, C. W., Jr.↗
DOE OSTI2020

Hazard analysis for identifying common cause failures of digital safety systems using a redundancy-guided systems-theoretic approach

Replacing the existing aging analog instrumentation and control (I&C) systems with modern safety control and protection, digital technology offers one of the foremost means of performance improvements and cost reductions for the existing nuclear power plants (NPPs). However, the qualification of digital I&C systems remains a challenge, especially considering the issue of software common-cause failures (CCFs), which are difficult to address. With the application and upgrades of advanced digital I&C systems, software CCFs have become a potential threat to plant safety because most redundant designs use similar digital platforms or software in the operating and application systems. With complex designs of multilayer redundancy to meet the single-failure criterion, digital I&C safety systems (e.g., engineered safety-features actuation system [ESFAS]) are of a particular concern in the U.S. Nuclear Regulatory Commission (NRC) licensing procedures. Here, this paper applies a modularized approach to conduct redundancy-guided systems-theoretic hazard analysis for an advanced digital ESFAS with multilevel redundancy designs. Systematic methods and risk-informed tools are incorporated to address both hardware and software CCFs, which provide guidance to eliminate the causal factors of potential single points of failure in the design of digital safety systems in advanced plant designs.

42 ENGINEERING↗
DOE OSTI2022

An Integrated Risk Assessment Process of Safety-Related Digital I&C Systems in Nuclear Power Plants

Upgrading the existing analog instrumentation and control (I&C) systems to state-of-the-art digital I&C (DI&C) systems will greatly benefit existing light water reactors. However, the issue of software common cause failure (CCF) remains an obstacle in terms of qualification for digital technologies. Existing analyses of CCFs in I&C systems mainly focus on hardware failures. With the application and upgrading of new DI&C systems, design flaws could cause software CCFs to become a potential threat to plant safety, considering that most redundancy designs use similar digital platforms or software in their operating and application systems. With complex multilayer redundancy designs to meet the single failure criterion, these I&C safety systems are of particular concern in U.S. Nuclear Regulatory Commission licensing procedures. In Fiscal Year 2019, the Risk-Informed Systems Analysis (RISA) Pathway of the U.S. Department of Energy’s Light Water Reactor Sustainability Program initiated a project to develop a risk assessment strategy for delivering a strong technical basis to support effective, licensable, and secure DI&C technologies for digital upgrades and designs. An integrated risk assessment for the DI&C process was proposed for this strategy to identify potential key digital-induced failures, implement reliability analyses of related digital safety I&C systems, and evaluate the unanalyzed sequences introduced by these failures (particularly software CCFs) at the plant level. Here this paper summarizes these RISA efforts in the risk analysis of safety-related DI&C systems at Idaho National Laboratory.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Levels of Digitization, Digitalization, and Automation for Advanced Reactors

Much has been written about levels of automation (LOA), but comparatively little has been written about levels of digitization (LODi) and levels of digitalization (LODa). Digitization is a digital representation of analog information and is typical of migration from analog to digital control systems, digitalization involves enhancing the functionality of digital information, and automation changes control from humans to machines. Each of these technology implementations has its own scales, and each forms a viable type of functionality that should be considered not as a continuum toward automation but rather as separate categories of solutions that meet the needs of advanced reactors. In this paper we develop separate LODi, LODa, and LOA scales and demonstrate how conflation of these technologies, using the example of computer-based procedures, can lead to confusion in the design process. With the race to develop advanced reactors, the surest metric of success and safety is proper consideration of the right technology requirements for different control systems.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2021

INTEGRATED RISK ASSESSMENT OF DIGITAL I&C SAFETY SYSTEMS FOR NUCLEAR POWER PLANTS

Upgrading the existing analog instrumentation and control (I&C) systems to state-of-the-art digital I&C (DI&C) systems provides the foremost means to improve performance and reduce costs for existing light-water reactors (LWRs). However, qualification of digital technologies remains a challenge?especially the issue of software common cause failure (CCF), which has been difficult to address. Existing analyses of CCFs in I&C systems mainly focus on hardware failures. With the application and upgrading of new DI&C systems, software CCFs due to design flaws might become a potential threat to plant safety, considering that most redundancy designs use similar digital platforms or software in their operating and application systems. With complex multi-layer redundancy designs to meet the single failure criterion, these I&C safety systems are of particular concern in U.S. Nuclear Regulatory Commission (NRC) licensing procedures. In 2019, the Risk-Informed Systems Analysis (RISA) Pathway of the U.S. Department of Energy?s (DOE?s) Light Water Reactor Sustainability (LWRS) Program initiated a project to develop a risk assessment strategy for delivering a strong technical basis to support effective, licensable, secure DI&C technologies for digital upgrades/designs. An integrated risk assessment for the DI&C (RADIC) process was proposed for this strategy to identify potential key digital-induced failures, implement reliability analyses of related digital safety I&C systems, and evaluate the unanalyzed sequences introduced by these failures (particularly software CCFs) at the plant level. This paper summarizes these RISA efforts in the risk analysis of safety-related DI& systems at Idaho National Laboratory.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1973

Logic-controlled solid-state switchgear for 270 volt dc.

A feasibility study to design and demonstrate solid-state switchgear composed of circuit breakers and a power transfer switch is described. The switchgear operates on a nominal 270 Vdc circuit and controls power to a load up to 15 A. One circuit breaker may be interconnected to a second to form a power transfer switch. Breaker or switch on-off and transfer functions can be remotely controlled. Automatic overload trip-out is provided through an ultimate current trip and an I squared t trip for transient overcurrents lower than the ultimate current trip level. A number of reclosures with variable time delay between trip-out and reclosure are programmed and controlled by integrated analog and COSMOS logic circuits. A commutation circuit that creates minimal transient disturbances to either source or load was developed to interrupt current flow through the main SCR switching element.-

Waddington, D.↗
NASA NTRS1973

Logic-controlled solid state switchgear for 270 volts dc

A feasibility study to design and demonstrate solid state switchgear in the form of circuit breakers and a power transfer switch is described. The switchgear operates on a nominal 270 V dc circuit and controls power to a load of up to 15 amperes. One circuit breaker may be interconnected to a second breaker to form a power transfer switch. On-off and transfer functions of the breakers or the transfer switch are remotely controlled. A number of reclosures with variable time delay between tripout and reclosure are programmed and controlled by integrated analog and COSMOS logic circuits. A unique commutation circuit, that generates only minimal transient disturbance to either source or load, was developed to interrupt current flow through the main SCR switching element. Laboratory tests demonstrated performance of the solid state circuit breakers over specified voltage and temperature ranges.

Sundberg, G. R.↗
NASA NTRS1974

Real time computer data system for the 40 x 80 ft wind tunnel facility at Ames Research Center

The wind tunnel realtime computer system is a distributed data gathering system that features a master computer subsystem, a high speed data gathering subsystem, a quick look dynamic analysis and vibration control subsystem, an analog recording back-up subsystem, a pulse code modulation (PCM) on-board subsystem, a communications subsystem, and a transducer excitation and calibration subsystem. The subsystems are married to the master computer through an executive software system and standard hardware and FORTRAN software interfaces. The executive software system has four basic software routines. These are the playback, setup, record, and monitor routines. The standard hardware interfaces along with the software interfaces provide the system with the capability of adapting to new environments.

Cambra, J. M.↗
NASA NTRS1977

TVC actuator model

A prototype Space Shuttle Main Engine (SSME) Thrust Vector Control (TVC) Actuator analog model was successfully completed. The prototype, mounted on five printed circuit (PC) boards, was delivered to NASA, checked out and tested using a modular replacement technique on an analog computer. In all cases, the prototype model performed within the recording techniques of the analog computer which is well within the tolerances of the specifications.

Baslock, R. W.↗
NASA NTRS1984

Overview of magnetic bearing control and linearization approaches for annular magnetically suspended devices

An overview of magnetic bearing control and linearization approaches which have been considered for annular magnetically suspended devices is presented. These devices include the Annular Momentum Control Device and the Annular Suspension and Pointing System. Two approaches were investigated for controlling the magnetic actuator. One approach involves controlling the upper and lower electromagnets differentially about a bias flux. The bias flux can either be supplied by permanent magnets in the magnetic circuit or by bias currents. In the other approach, either the upper electromagnet or the lower electromagnet is controlled depending on the direction of force required. One advantage of the bias flux is that for small gap perturbations about a fixed operating point, the force-current characteristic is linear. Linearization approaches investigated for individual element control include an analog solution of the nonlinear electromagnet force equation and a microprocessor-based table lookup method.

Groom, N. J.↗
NASA NTRS1990

A solution adaptive grid procedure for an upwind parabolized flow solver

A solution adaptive grid procedure based on an error equi-distribution scheme is developed and applied to a Parabolized Navier-Stokes solver. An improved method for selecting weighting functions is introduced which involves normalizing a combination of flowfield gradients and curvature of a number of dependent variables and then selecting the largest at each point. The scheme re-distributes grid points line-by-line, with grid point motion controlled by forces analogous to tensional and torsional spring forces with the spring constants set equal to the weighting functions. Torsional terms are functions of the grid point positions along neighboring grid lines and provide grid smoothness and stability. A grid-fitting scheme is introduced for external flows in which the number of grid points in the freestream are reduced to a minimum. Results for several problems are presented to demonstrate the improvements obtainable with the solution adaptive grid procedure.

Harvey, Albert D.↗
NASA NTRS1991

Reduced-Wiring Tactile Sensor

Proposed tactile sensor on robot finger puts out multiplexed analog signals transmitted to control computer on fewer wires than needed to transmit equivalent digital signals. Analog output represents data on contact area of object being gripped, on position of object, and on direction and rate of slippage if any. Consists of chains of normally open switches and resistors on surface of finger. Each resistance double preceding resistance in each chain. Constant-current sources supply power to chains.

Ohm, Timothy R.↗
NASA NTRS1991

A real time dynamic data acquisition and processing system for velocity, density, and total temperature fluctuation measurements

The real time Dynamic Data Acquisition and Processing System (DDAPS) is described which provides the capability for the simultaneous measurement of velocity, density, and total temperature fluctuations. The system of hardware and software is described in context of the wind tunnel environment. The DDAPS replaces both a recording mechanism and a separate data processing system. DDAPS receives input from hot wire anemometers. Amplifiers and filters condition the signals with computer controlled modules. The analog signals are simultaneously digitized and digitally recorded on disk. Automatic acquisition collects necessary calibration and environment data. Hot wire sensitivities are generated and applied to the hot wire data to compute fluctuations. The presentation of the raw and processed data is accomplished on demand. The interface to DDAPS is described along with the internal mechanisms of DDAPS. A summary of operations relevant to the use of the DDAPS is also provided.

Clukey, Steven J.↗
NASA NTRS1991

Analog synthesized fast-variable linear load

A several kilowatt power level, fast-variable linear resistor was synthesized by using analog components to control the conductance of power MOSFETs. Risetimes observed have been as short as 500 ns with respect to the control signal and 1 to 2 microseconds with respect to the power source voltage. A variant configuration of this load that dissipates a constant power set by a control signal is indicated. Replacement of the MOSFETs by static induction transistors (SITs) to increase power handling, speed and radiation hardness is discussed.

Niedra, Janis M.↗
NASA NTRS1991

Analog synthesized fast-variable linear load

A several-kilowatt power level, fast-variable linear resistor has been synthesized by using analog components to control the conductance of power MOSFETs. Risetimes observed have been as short as 500 ns with respect to the control signal and 1 to 2 microsec with respect to the power source voltage. A variant configuration of this load that dissipates a constant power set by a control signal is indicated. Replacement of the MOSFETs by static induction transistors to increase power handling, speed, and radiation hardness is discussed.

Niedra, Janis M.↗
NASA NTRS1993

Space marching calculations about hypersonic configurations using a solution-adaptive mesh algorithm

A solution-adaptive marching algorithm is developed and applied to a three-dimensional parabolized Navier-Stokes equation solver. The resulting algorithm obtains accurate solutions by using a spatial-marching/adaptive grid procedure. The adaptation step redistributes grid points line by line in both crossflow directions, with grid point motion controlled by forces analogous to tensional and torsional spring forces with the tensional force proportional to the error measure or weighting functions. The solution-adaptive marching procedure is applied to the hypersonic flow about two generic aircraft configurations. The first of these is an all-body-type geometry with elliptical cross sections and is studied at angles of attack of 0.5, and 15 deg. The second geometry is a generic blended-wing-body design. Results are presented that demonstrate the improvements in flowfield resolution obtainable with the solution-adaptive marching procedure over conventional fixed grid techniques. Computed pitot pressure profiles obtained using the solution-adaptive algorithm show improved agreement with experimental data compared to predictions obtained using a fixed grid.

Harvey, Albert D.↗
NASA NTRS1994

Electronically Variable Resistive Load

Electronically variable linear resistive load circuit synthesized by use of analog components to control conductance of power metal oxide/semiconductor field-effect transistors, MOSFET's. Circuit has modular configuration, in which single controller drives parallel load units. A 3-kW load module that exhibits submicrosecond response time with respect to control signal demonstrated.

Niedra, Janis M.↗