Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “amorphous materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Hard x-ray methods for studying the structure of amorphous thin films and bulk glassy oxides

High-energy photon diffraction minimizes many of the corrections associated with laboratory x-ray diffractometers, and enables structure factor measurements to be made over a wide range of momentum transfers. The method edges us closer toward an ideal experiment, in which coordination numbers can be extracted without knowledge of the sample density. Three case studies are presented that demonstrate new hard x-ray methods for studying the structure of glassy and amorphous materials. First, the methodology and analysis of high-energy grazing incidence on thin films is discussed for the case of amorphous In 2 O 3 . Additionally, the connectivity of irregular InO 6 polyhedra are shown to exist in face-, edge- and corner-shared configurations in the approximate ratio of 1:2:3. Secondly, the technique of high-energy small and wide angle scattering has been carried out on laser heated and aerodynamically levitated samples of silica-rich barium silicate (20BaO:80SiO 2 ), from the single phase melt at 1500 C-o to the phase separated glass at room temperature. Based on Ba-O coordination numbers of 6 to 7, it is argued that the although the potential of Ba is ionic, it is weak enough to cause the liquid-liquid immiscibility to become metastable. Lastly, high-energy small and wide angle scattering has also been applied to high water content (up to 12 wt.%) samples of hydrous SiO 2 glass quenched from 1500 C-o at 4 GPa. An increase of Si 1 O 2 correlations at 4.3 angstrom is found to be consistent with an increase in the population of three-membered SiO 4 rings at the expense of larger rings.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Use of X-ray diffraction to quantify amorphous supplementary cementitious materials in anhydrous and hydrated blended cements

The content of individual amorphous supplementary cementitious materials (SCMs) in anhydrous and hydrated blended cements was quantified by the PONKCS [1] X-ray diffraction (XRD) method. The analytical precision and accuracy of the method were assessed through comparison to a series of mixes of known phase composition and of increasing complexity. A 2σ precision smaller than 2–3 wt.% and an accuracy better than 2 wt.% were achieved for SCMs in mixes with quartz, anhydrous Portland cement, and hydrated Portland cement. The extent of reaction of SCMs in hydrating binders measured by XRD was 1) internally consistent as confirmed through the standard addition method and 2) showed a linear correlation to the cumulative heat release as measured independently by isothermal conduction calorimetry. The advantages, limitations and applicability of the method are discussed with reference to existing methods that measure the degree of reaction of SCMs in blended cements.

36 MATERIALS SCIENCE↗

Electro-active polymers containing pendent 2,7-diarylfluorene fragments as materials for OLEDs

Poly[2-phenyl-7-(4-vinylphenyl)-9,9-diethylfluorene)], poly[2-(1-naphtyl)-7-(4-vinylphenyl)-9,9-diethylfluorene)] and poly[2-(4-biphenyl)-7-(4-vinylphenyl)-9,9-diethylfluorene)] were synthesized and characterized by NMR spectroscopy, elemental analysis and gel permeation chromatography. The derivatives represent materials of high thermal stability with initial thermal destruction temperatures from 390°C to 400 °C. The glass transition temperatures of the amorphous materials were 182 °C, 151 °C and 159 °C respectively. Hole-transporting properties of the polymeric materials were tested in the structures of organic light emitting diodes with Alq{sub 3} as the green emitter and electron transporting material. The device containing hole-transporting layers of polymer with 2-(4-biphenyl)-7-(4-vinylphenyl)-9,9-diethylfluorene moieties exhibited the best overall performance with turn on voltage of 3.6 V, a maximum photometric efficiency of 3.1 cd/A and maximum brightness of about 5300 cd/m{sup 2}.

36 MATERIALS SCIENCE↗

Materials research

The research is reported concerned with materials for aerospace applications. Areas reported include: electrical properties of glasses, oxides and metals; structural and high temperature properties of crystalline and amorphous materials; and physical properties, and microstructure of materials.

Source record↗

Pauling’s rules for oxide-based minerals: A re-examination based on quantum mechanical constraints and modern applications of bond-valence theory to Earth materials

Since their introduction in 1929, Pauling’s five rules have been used by scientists from many disciplines to rationalize and predict stable arrangements of atoms and coordination polyhedra in crystalline solids; amorphous materials such as silicate glasses and melts; nanomaterials, poorly crystalline solids; aqueous cation and anion complexes; and sorption complexes at mineral-aqueous solution interfaces. The predictive power of these simple yet powerful rules was challenged recently by George et al. (2020), who performed a statistical analysis of the performance of Pauling’s five rules for about 5000 oxide crystal structures. They concluded that only 13% of the oxides satisfy the last four rules simultaneously and that the second rule has the most exceptions. They also found that Pauling’s first rule is satisfied for only 66% of the coordination environments tested and concluded that no simple rule linking ionic radius to coordination environment will be predictive due to the variable quality of univalent radii. We address these concerns and discuss quantum mechanical calculations that complement Pauling’s rules, particularly his first (radius sum and radius ratio rule) and second (electrostatic valence rule) rules. We also present a more realistic view of the bonded radii of atoms, derived by determining the local minimum in the electron density distribution measured along trajectories between bonded atoms known as bond paths, i.e., the bond critical point (rc). Electron density at the bond critical point is a quantum mechanical observable that correlates well with Pauling bond strength. Moreover, a metal atom in a polyhedron has as many bonded radii as it has bonded interactions, resulting in metal and O atoms that may not be spherical. O atoms, for example, are not spherical in many oxide-based crystal structures. Instead, the electron density of a bonded oxygen is often highly distorted or polarized, with its bonded radius decreasing systematically from ~1.38 Å when bonded to highly electropositive atoms like sodium to 0.64 Å when bonded to highly electronegative atoms like nitrogen. Bonded radii determined for metal atoms match the Shannon (1976) radii for more electropositive atoms, but the match decreases systematically as the electronegativities of the M atoms increase. As a result, significant departures from the radius ratio rule in the analysis by George et al. (2020) is not surprising. We offer a modified, more fundamental version of Pauling’s first rule and demonstrate that the second rule has a one-to-one connection between the electron density accumulated between the bonded atoms at the bond critical point and the Pauling bond strength of the bonded interaction. Pauling’s second rule implicitly assumes that bond strength is invariant with bond length for a given pair of bonded atoms. Many studies have since shown that this is not the case, and Brown and Shannon (1973) developed an equation and a set of parameters to describe the relation between bond length and bond strength, now redefined as bond valence to avoid confusion with Pauling bond-strength. Brown (1980) used the valence-sum rule, together with the path rule and the valence-matching principle, as the three axioms of bond-valence theory (BVT), a powerful method for understanding many otherwise elusive aspects of crystals and also their participation in dynamic processes. We show how a priori bond-valence calculations can predict unstrained bond-lengths and how bond-valence mapping can locate low-Z atoms in a crystal structure (e.g., Li) or examine possible diffusion pathways for atoms through crystal structures. In addition, we briefly discuss Pauling’s third, fourth, and fifth rules, the first two of which concern the sharing of polyhedron elements (edges and faces) and the common instability associated with structures in which a polyhedron shares an edge or face with another polyhedron and contains high-valence cations. The olivine [α-(MgxFe1–x)2SiO4] crystal structure is used to illustrate the distortions from hexagonal close-packing of O atoms caused by metal-metal repulsion across shared polyhedron edges. We conclude by discussing several applications of BVT to Earth materials, including the use of BVT to: (1) locate H+ ions in crystal structures, including the location of protons in the crystal structures of nominally anhydrous minerals in Earth’s mantle; (2) determine how strongly bonded (usually anionic) structural units interact with weakly bonded (usually cationic) interstitial complexes in complex uranyl-oxide and uranyl-oxysalt minerals using the valence-matching principle; (3) calculate Lewis acid strengths of cations and Lewis base strengths of anions; (4) determine how (H2O) groups can function as bond-valence transformers by dividing one bond into two bonds of half the bond valence; (5) help characterize products of sorption reactions of aqueous cations (e.g., Co2+ and Pb2+) and oxyanions [e.g., selenate (Se6+O4)2- and selenite (Se4+O3)2-] at mineral-aqueous solution interfaces and the important role of protons in these reactions; and (6) help characterize the local coordination environments of highly charged cations (e.g., Zr4+, Ti4+, U4+, U5+, and U6+) in silicate glasses and melts.

Geochemistry & Geophysics↗

Liquid-like phase formation in Gd{sub 2}Zr{sub 2}O{sub 7} by extremely ionizing irradiation

Isometric Gd{sub 2}Zr{sub 2}O{sub 7} with the ordered, pyrochlore structure has an extremely high resistance to radiation-induced amorphization. Ion-beam irradiations at keV to GeV energies result in a disordered, defect-fluorite structure that remains crystalline to very large fluences. However, we report liquid-like phase formation of droplet-like surface hillocks and quenched molten tracks in Gd{sub 2}Zr{sub 2}O{sub 7}. The extremely high energy density of 12-MeV C{sub 60} clusters creates tracks with substantial volumes of amorphous material, accompanied by the formation of nanocrystals of the disordered, defect-fluorite structure. This is the first evidence of irradiation-induced amorphization of Gd{sub 2}Zr{sub 2}O{sub 7}. In contrast, irradiation of Gd{sub 2}Zr{sub 2}O{sub 7} pyrochlore with swift heavy ions of U resulted in an order-disorder transformation to defect-fluorite without any evidence of amorphization. Thermal-spike calculations highlight the dominance of the effect of deposited energy density, controlled by the projectile velocity, as compared with the energy loss.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Equilibrium ultrastable glasses produced by random pinning

Ultrastable glasses have risen to prominence due to their potentially useful material properties and the tantalizing possibility of a general method of preparation via vapor deposition. Despite the importance of this novel class of amorphous materials, numerical studies have been scarce because achieving ultrastability in atomistic simulations is an enormous challenge. Here, we bypass this difficulty and establish that randomly pinning the position of a small fraction of particles inside an equilibrated supercooled liquid generates ultrastable configurations at essentially no numerical cost, while avoiding undesired structural changes due to the preparation protocol. Building on the analogy with vapor-deposited ultrastable glasses, we study the melting kinetics of these configurations following a sudden temperature jump into the liquid phase. In homogeneous geometries, we find that enhanced kinetic stability is accompanied by large scale dynamic heterogeneity, while a competition between homogeneous and heterogeneous melting is observed when a liquid boundary invades the glass at constant velocity. Our work demonstrates the feasibility of large-scale, atomistically resolved, and experimentally relevant simulations of the kinetics of ultrastable glasses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of CH{sub 2} content and network defects on the elastic properties of organosilicate glasses

Organosilicate glasses (OSGs) are used as low-k intermetal dielectrics for advanced integrated circuits. In this application, the material must fulfill two conflicting requirements: It has to have low density to reduce the dielectric constant while being sufficiently mechanically stable to withstand thermomechanical and other stresses during subsequent steps of integrated circuit manufacture. Recent experimental advances in improving the mechanical and electrical properties of these materials have not yet been systematically studied theoretically at the ab initio level due to the large model sizes necessary to realistically describe amorphous materials. In this paper we employ the density-functional-based tight-binding method to achieve an accurate description of OSG properties at different compositions. We analyze the influence of composition and local network defects on the density and bulk modulus of nonporous OSG. We find that the dependence of density and that of mechanical stiffness on chemical composition are of different natures. This difference is traced to a transition between mechanisms of elastic deformation in silica glass and in silicon hydrocarbide, which is also the reason for the two materials' different sensitivities to network defects.

36 MATERIALS SCIENCE↗

Optical constants of solid methane

Methane is the most abundant simple organic molecule in the outer solar system bodies. In addition to being a gaseous constituent of the atmospheres of the Jovian planets and Titan, it is present in the solid form as a constituent of icy surfaces such as those of Triton and Pluto, and as cloud condensate in the atmospheres of Titan, Uranus, and Neptune. It is expected in the liquid form as a constituent of the ocean of Titan. Cometary ices also contain solid methane. The optical constants for both solid and liquid phases of CH4 for a wide temperature range are needed for radiative transfer calculations, for studies of reflection from surfaces, and for modeling of emission in the far infrared and microwave regions. The astronomically important visual to near infrared measurements of solid methane optical constants are conspicuously absent from the literature. Preliminary results are presented on the optical constants of solid methane for the 0.4 to 2.6 micrometer region. Deposition onto a substrate at 10 K produces glassy (semi-amorphous) material. Annealing this material at approximately 33 K for approximately 1 hour results in a crystalline material as seen by sharper, more structured bands and negligible background extinction due to scattering. The constant k is reported for both the amorphous and the crystalline (annealed) states. Typical values (at absorption maxima) are in the .001 to .0001 range. Below lambda = 1.1 micrometers the bands are too weak to be detected by transmission through the films less than or equal to 215 micrometers in thickness, employed in the studies to date. Using previously measured values of the real part of the refractive index, n, of liquid methane at 110 K, n is computed for solid methane using the Lorentz-Lorenz relationship. Work is in progress to extend the measurements of optical constants n and k for liquid and solid to both shorter and longer wavelengths, eventually providing a complete optical constants database for condensed CH4.

Khare, Bishun N.↗

Femtosecond X-ray Diffraction of Laser-shocked Forsterite (Mg 2 SiO 4 ) to 122 GPa

The response of forsterite, Mg 2 SiO 4 , under dynamic compression is of fundamental importance for understanding its phase transformations and high-pressure behavior. Here, we have carried out an in situ X-ray diffraction study of laser-shocked polycrystalline and single-crystal forsterite from 19 to 122 GPa using the Matter in Extreme Conditions end-station of the Linac Coherent Light Source. Under laser-based shock loading, forsterite does not transform to the high-pressure equilibrium assemblage of MgSiO 3 bridgmanite and MgO periclase, as has been suggested previously. Instead, we observe forsterite and forsterite III, a metastable polymorph of Mg 2 SiO 4 , coexisting in a mixed-phase region from 33 to 75 GPa for both polycrystalline and single-crystal samples. Densities inferred from X-ray diffraction are consistent with earlier gas-gun shock data. At higher stress, the response is sample-dependent. Polycrystalline samples undergo amorphization above 79 GPa. For [010]- and [001]-oriented crystals, a mixture of crystalline and amorphous material is observed to 108 GPa, whereas the [100]-oriented forsterite adopts an unknown phase at 122 GPa. The first two sharp diffraction peaks of amorphous Mg 2 SiO 4 show a similar trend with compression as those observed for MgSiO 3 in both recent static- and laser-driven shock experiments. This study provides new insight into the transformation of forsterite under nanosecond-duration shock loading. This work emphasizes the importance of formation of metastable phases along the Hugoniot and adds to evidence that the 300-K single-crystal diamond anvil cell experiments have relevance for understanding structures formed under shock compression. In particular, the metastable phase forsterite III has now been shown to form under dynamic compression from 10s to 100s of nanoseconds as well as under 300-K static compression. Upon compression to higher pressures, Mg 2 SiO 4 transforms to an amorphous phase. These results have broad relevance for understanding the behavior of silicates under dynamic compression.

36 MATERIALS SCIENCE↗

Co-templating of polyoxoniobates and silicate/germanate trimer-rings in crystals and inorganic gels

Polyoxometalate (POM) supramolecular gels are a growing family of materials, both for understanding fundamental self-assembly and fabricating flexible monolithic materials that retain the function of metal oxides. Here, we exploited the pH-dependent speciation of polyoxoniobates (PONbs), targeting the formation of PONb-containing supramolecular gels that contain other low molecular weight components (silicate, germanate, phosphate, and carbonate). The introduction of gaseous CO 2 into aqueous hexaniobate solutions resulted in the formation of both new crystalline phases and highly transparent gels. The crystalline phases, formulated Cs 24 [Nb 7 O 22 (NbO(CO 3 ) 2 ) 9 (Si 3 O 9 )]·19.6H 2 O and Cs 21 Na 3 [Nb 7 O 22 (NbO(CO 3 ) 2 ) 9 (Ge 3 O 9 )]·33.6H 2 O are templated by a rare planar [X 3 O 9 ] 6− (X = Si, Ge) ring. Crystalline phases were not obtained with phosphate; instead, the gels contain a mixture of phosphate-centred PONbs and network-forming phosphate. POM speciation within the gels, physical properties, and assembly mechanisms were benchmarked by solution and solid-state nuclear magnetic resonance (NMR) spectroscopy, vibrational spectroscopies, small-angle X-ray scattering (SAXS), and thermogravimetry-mass spectroscopy. Optical analysis and dielectric behavior of the gels confirmed that they are highly transparent ionic and electronic conductors. The alkali and hydroxide concentration controls the formation of crystalline materials or supramolecular gels while maintaining the same network building blocks, providing a rare opportunity to describe the molecular-level structure of inorganic amorphous materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of space environment on structural materials

A preliminary study of materials exposed in space in a low Earth orbit for nearly six years has revealed a wide range of micrometeorite or microparticle impact craters ranging in size from 1 to 1000 micron in diameter, debris particles from adjacent and distant materials systems, reaction products, and other growth features on the specimen surfaces, and related phenomena. The exposed surface features included fine grained and nearly amorphous materials as well as a large array of single crystal particles. A replication type, lift off technique was developed to remove reaction products and debris from the specimen surfaces in order to isolate them from the background substrate without creating microchemical or microstructural artifacts or alterations. This resulted in surface features resting on a carbon support film which was virtually invisible to observation by electron microscopy and nondispersive x ray analysis. Some evidence for blisters on leading edge aluminum alloy surfaces and a high surface region concentration of oxygen determined by Auger electron spectrometry suggests oxygen effects where fluences exceed 10(exp 21) atoms/sq cm.

Miglionico, C.↗

A general-purpose machine learning framework for predicting properties of inorganic materials

A very active area of materials research is to devise methods that use machine learning to automatically extract predictive models from existing materials data. While prior examples have demonstrated successful models for some applications, many more applications exist where machine learning can make a strong impact. To enable faster development of machine-learning-based models for such applications, we have created a framework capable of being applied to a broad range of materials data. Our method works by using a chemically diverse list of attributes, which we demonstrate are suitable for describing a wide variety of properties, and a novel method for partitioning the data set into groups of similar materials to boost the predictive accuracy. In this manuscript, we demonstrate how this new method can be used to predict diverse properties of crystalline and amorphous materials, such as band gap energy and glass-forming ability.

36 MATERIALS SCIENCE↗

Raman gain control in optical fibers with orbital-angular-momentum-induced chirality of light

Stimulated Raman scattering is a particularly robust nonlinearity, occurring in virtually every material because its spectral linewidth and associated frequency shift do not typically depend on phases or directions (i.e. wavevectors) of the interacting light beams. In amorphous materials such as glass fibers, Raman bandwidths are large, enabling its use as a broadband gain element. This ubiquity makes it a versatile means for achieving optical amplification or realizing lasers over a large range of pulsewidths at user-defined colors. However, this ease of deploying the effect also presents itself as a stubborn source of noise in fiber-based quantum sources or parasitic emission in fiber lasers. Here, we show that orbital angular momentum carrying light beams experiencing spin-orbit interactions yield novel phase-matching criteria for Raman scattering. This enables tailoring its spectral shape (by over half the Raman shift in a given material) as well as strength (by ∼ 100×) simply by controlling light’s topological charge – a capability of utility across the multitude of applications where modulating Raman scattering is desired.

Liu, Xiao (ORCID:000000032239762X)↗

Strain localization in dry sheared granular materials: A compactivity-based approach

Shear banding is widely observed in natural fault zones as well as in laboratory experiments on granular materials. Understanding the dynamics of strain localization under different loading conditions is essential for quantifying strength evolution of fault gouge, energy partitioning during earthquakes and characterizing rheological transitions and fault zone structure changes. To that end, we develop a physics-based continuum model for strain localization in sheared granular materials. The grain-scale dynamics is described by the Shear Transformation Zone (STZ) theory, a non-equilibrium statistical thermodynamic framework for viscoplastic deformation in amorphous materials. Using a finite strain computational framework, we investigate the initiation and growth of complex shear bands under a variety of loading conditions and identify implication for strength evolution and ductile to brittle transition. Our numerical results show similar localization patterns to field and lab observations and suggest that shear zones show more ductile response at higher confining pressures, lower dilatancy and loose initial conditions. Lower pressures, higher dilatancy and dense initial conditions favor a brittle response and larger strength drops. These findings shed light on a range of mechanisms for strength evolution in dry sheared granular materials and provide a critical input to physicsbased multiscale models of fault zone instabilities.

36 MATERIALS SCIENCE↗

Thermally activated structural transformations in manganese oxide nanoparticles under air and argon atmospheres

The properties of manganese oxide nanomaterials are dictated by the structure and morphology of the particular phases they can adopt. The effects of post-synthesis heat treatments on amorphous monodisperse manganese oxide nanoparticles at ≤1300° under lab. air and argon atmospheres were investigated using X-ray diffraction, thermal analysis and electron microscopy techniques. During heat treatments in air, the nanoparticles undergo three transformations, resulting in: crystallization to cubic Mn 2 O 3 at ~500°, followed by the transformation to tetragonal Mn 3 O 4 at ~1010°, and to cubic Mn 3 O 4 at ~1190°. The first two transformations are irreversible, are associated with oxygen loss, and involve reductions. of the Mn ions. The latter transformation is polymorphic and spontaneously reversible, and so, tetragonal Mn 3 O 4 is observed at ambient temperature in samples heat-treated at >1000°. The samples heat treated in argon firstly crystallize to a mixt. of monoclinic Mn 2 O 3 and tetragonal Mn 3 O 4 at ~475°, followed by complete transformation to tetragonal Mn 3 O 4 at ~820°, and then to mostly cubic MnO at ~1145°; here again, the residual tetragonal Mn 3 O 4 undergoes a reversible polymorphic transformation at ~1180°, whereas the other transformations are irreversible. In both atmospheres, the amorphous material exhibits short-range cryptomelane-type order with a mixture of Mn 3+ and Mn 4+ prior to crystallization. Furthermore, these data indicate that most of the stable manganese oxide phases can be obtained from initially amorphous nanoparticles by heat treatment under appropriate conditions.

36 MATERIALS SCIENCE↗

Local-order metric for condensed-phase environments

Here we introduce a local order metric (LOM) that measures the degree of order in the neighborhood of an atomic or molecular site in a condensed medium. The LOM maximizes the overlap between the spatial distribution of sites belonging to that neighborhood and the corresponding distribution in a suitable reference system. The LOM takes a value tending to zero for completely disordered environments and tending to one for environments that perfectly match the reference. The site-averaged LOM and its standard deviation define two scalar order parameters, S and δS, that characterize with excellent resolution crystals, liquids, and amorphous materials. We show with molecular dynamics simulations that S, δS, and the LOM provide very insightful information in the study of structural transformations, such as those occurring when ice spontaneously nucleates from supercooled water or when a supercooled water sample becomes amorphous upon progressive cooling.

36 MATERIALS SCIENCE↗

Melt-cast organic glasses as high-efficiency fast neutron scintillators

In this work we report a new class of organic-based scintillators that combines several of the desirable attributes of existing crystalline, liquid, and plastic organic scintillators. The prepared materials may be isolated in single crystalline form or melt-cast to produce highly transparent glasses that have been shown to provide high light yields of up to 16,000 photons/MeVee, as evaluated against EJ-200 plastic scintillators and solution-grown trans -stilbene crystals. The prepared organic glasses exhibit neutron/gamma pulse-shape discrimination (PSD) and are compatible with wavelength shifters to reduce optical self-absorption effects that are intrinsic to pure materials such as crystalline organics. In conclusion, the combination of high scintillation efficiency, PSD capabilities, and facile scale-up via melt-casting distinguishes this new class of amorphous materials from existing alternatives.

36 MATERIALS SCIENCE↗