Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aerodynamic modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Aerodynamic detuning for aeroelastic control of stability and forced response of supersonic rotors

An unsteady aerodynamic model is developed to analyze flutter and aerodynamically forced response of aerodynamically detuned supersonic axial flow rotors. Alternate blade aerodynamic detuning is considered, accomplished by alternating the circumferential spacing of adjacent blades as small solidity variations which do not have a dominant effect on the steady performance of a rotor. The unsteady aerodynamics are determined by developing an influence coefficient technique which is appropriate for both aerodynamically tuned and detuned rotor configurations. Torsion mode rotor stability and aerodynamically forced response are then analyzed with this unsteady aerodynamic model by combining it with a single-degree-of-freedom structural model. The effects of this detuning on the flutter and forced response characteristics of supersonic axial flow rotors is then demonstrated by considering baseline twelve bladed rotors.

Spara, Karen M.↗
NASA NTRS2019

Unsteady Model Estimation for Generic T-Tail Transport Aircraft Using Computational Data

Models including nonlinear and unsteady behaviors are developed for the longitudinal axis of the NASA Generic T-Tail Aircraft over a large range of angle of attack. These models are based on computational simulations of forced-oscillation tests in a wind tunnel. This work continues a recent study and an ongoing effort by NASA to improve aircraft simulations for pilot training in loss-of-control and stalled conditions. The objective of this work is to develop appropriate aerodynamic models that provide representative responses in simulation for a given class of aircraft. In the stall region, nonlinear unsteady responses are often present and may require an extended aerodynamic model compared to that used in the conventional flight envelope. In this study, two objectives are addressed. The first is to obtain representative models for the NASA Generic T-Tail aircraft over a wide range of angle of attack and the second is to continue development of a specialized CFD test technique that uses Schroeder sweeps to create information rich responses for unsteady aerodynamic model identification.

Murphy, Patrick C.↗
NASA NTRS2020

An Overview of NASA’s Learn-to-Fly Technology Development

“Learn-to-Fly” (L2F) is an advanced technology development effort within the Modeling and Control for Agile Aircraft Development (MCAAD) group, a part of the NASA Transformative Aeronautics Concepts Program’s (TACP) Transformational Tools and Technologies (TTT) project. The goal of L2F is to develop technologies for enabling self-learning flight vehicles, using both ground- and flight-test approaches. Specifically, research has been conducted to demonstrate the potential to merge two enabling technologies, real-time aerodynamic modeling and adaptive flight controls, to substantially reduce the typical ground- and flight-testing time requirements for air vehicle design. This effort involved development of real-time, on-board algorithms to demonstrate key L2F technologies including aerodynamic modeling and control for an aircraft with minimal a priori knowledge. This research included both ground-based wind tunnel experiments utilizing modern design of experiments (DOE) techniques, as well as a flight test campaign, and was intended to rapidly advance these technologies and demonstrate key capabilities of the L2F approach. This paper presents the overview of the methods used to develop L2F technologies in NASA Langley Research Center’s 12-Foot Low Speed Tunnel, as well as in flight experiments. These methods include efficient wind tunnel data collection, real-time global nonlinear aerodynamic modeling in both the time and frequency domains, and the integration of the modeling techniques with adaptive flight controls, all of which were demonstrated using experimental validation.

Stephen E Riddick↗
NASA NTRSDate not supplied

Comparison of Entry Descent and Landing Aerodynamic Databases with Uncertainty Quantification Developed Using Machine Learning Techniques

When developing the aerodynamic databases for use in trajectory simulations, it is important to develop a system of metrics to qualify which aerodynamic models are best to use. Since aerodynamics are just one input into trajectory simulations, the results of these simulations do not reflect on the quality of the aerodynamic database used. This means that aerodynamic database comparisons must be done offline. While traditional metrics that focus on mean/nominal predictions are a good first step, more robust estimates of the prediction interval become important as more focused uncertainty models are developed. We explore the limitations of evaluating aerodynamic models based purely on nominal-centered response surfaces. Before elaborating and evaluating metrics based on distributed models, the value of evaluating prediction interval and confidence interval are discussed to conclude that prediction intervals are more relevant to the use of trajectory analysis. Several metrics to evaluate the prediction interval are introduced with a focus on the standard calibration metric. Finally, we compare candidate models using both mean and distributed metrics. A finalized candidate model developed using state of the art machine learning methods is compared to a baseline model developed using traditional aerodynamic database modeling techniques.

Aerodynamic Database↗
NASA NTRS2000

Results From F-18B Stability and Control Parameter Estimation Flight Tests at High Dynamic Pressures

A maximum-likelihood output-error parameter estimation technique has been used to obtain stability and control derivatives for the NASA F-18B Systems Research Aircraft. This work has been performed to support flight testing of the active aeroelastic wing (AAW) F-18A project. The goal of this research is to obtain baseline F-18 stability and control derivatives that will form the foundation of the aerodynamic model for the AAW aircraft configuration. Flight data have been obtained at Mach numbers between 0.85 and 1.30 and at dynamic pressures ranging between 600 and 1500 lbf/sq ft. At each test condition, longitudinal and lateral-directional doublets have been performed using an automated onboard excitation system. The doublet maneuver consists of a series of single-surface inputs so that individual control-surface motions cannot be correlated with other control-surface motions. Flight test results have shown that several stability and control derivatives are significantly different than prescribed by the F-18B aerodynamic model. This report defines the parameter estimation technique used, presents stability and control derivative results, compares the results with predictions based on the current F-18B aerodynamic model, and shows improvements to the nonlinear simulation using updated derivatives from this research.

Moes, Timothy R.↗
NASA NTRS1995

One-Equation Turbulence Models in Aerodynamics

The present paper shows under which assumptions one-equation models can be derived from two-equation models. Based on that transformation a new one-equation turbulence model is derived that basically behaves like a two-equation model. The new model is compared in detail against existing models

Menter, F. R.↗
NASA NTRS2017

New Flutter Analysis Technique for Time-Domain Computational Aeroelasticity

A new time-domain approach for computing flutter speed is presented. Based on the time-history result of aeroelastic simulation, the unknown unsteady aerodynamics model is estimated using a system identification technique. The full aeroelastic model is generated via coupling the estimated unsteady aerodynamic model with the known linear structure model. The critical dynamic pressure is computed and used in the subsequent simulation until the convergence of the critical dynamic pressure is achieved. The proposed method is applied to a benchmark cantilevered rectangular wing.

HWB aircraft↗
NASA NTRSDate not supplied

High-Fidelity Simulations of Lift+Cruise VTOL Urban Air Mobility Concept Aircraft in Hover

This paper presents progress of high-fidelity multidisciplinary simulations for the NASA lift+cruise vertical takeoff and landing (VTOL) urban air mobility concept aircraft in hover. The study focuses on the unsteady flow solutions featuring strong wake interactions between rotors and the airframe. The simulations couple a high-fidelity aerodynamic model with a comprehensive rotorcraft aeromechanics tool with rotor rotation-speed trim. The aerodynamic model is based on the Reynolds-averaged Navier-Stokes equations using the one-equation Spalart-Allmaras turbulence model with rotation correction. Unsteady aerodynamic flows are computed on a dynamic, deformable, unstructured, overset grid system. An integrated overset-grid assembler is used to construct the composite grid from 23 component grids and facilitate communications between individual component grids. Rotor performance and airframe forces and moments are computed and compared on two unstructured grids. The study demonstrates capabilities of high-fidelity multidisciplinary analysis tools to capture the strong unsteady flowfield around this multi-rotor aircraft in hover.

CFD↗
NASA NTRSDate not supplied

High-Fidelity Simulations of Lift+Cruise VTOL Urban Air Mobility Concept Aircraft in Hover

This presentation presents progress of high-fidelity multidisciplinary simulations for the NASA lift+cruise vertical takeoff and landing (VTOL) urban air mobility concept aircraft in hover. The study focuses on the unsteady flow solutions featuring strong wake interactions between rotors and the airframe. The simulations couple a high-fidelity aerodynamic model with a comprehensive rotorcraft aeromechanics tool with rotor rotation-speed trim. The aerodynamic model is based on the Reynolds-averaged Navier-Stokes equations using the one-equation Spalart-Allmaras turbulence model with rotation correction. Unsteady aerodynamic flows are computed on a dynamic, deformable, unstructured, overset grid system. An integrated overset-grid assembler is used to construct the composite grid from 23 component grids and facilitate communications between individual component grids. Rotor performance and airframe forces and moments are computed and compared on two unstructured grids. The study demonstrates capabilities of high-fidelity multidisciplinary analysis tools to capture the strong unsteady flowfield around this multi-rotor aircraft in hover.

CFD↗
DOE OSTI2023

Modeling the Yaw Behavior of Tail Fins for Small Wind Turbines: November 22, 2021 - May 21, 2024

This report describes the aerodynamic modelling of the yaw behavior of tail fins for small wind turbines (SWTs). The analysis is based on unsteady slender body theory (USBT) and is formulated to be used with the proposed tail fin module to be added to OpenFAST. Linearized USBT, which has been applied in the past to SWT tail fins, is developed in three main ways. First, USBT is extended to high yaw angles and aspect ratios by modelling the associated nonlinear vortex dynamics and the chordwise load distribution respectively. Second, we consider the effect of time-varying wind speed. The extended theory is compared to recent unpublished measurements at the University of Perugia, Italy, for the yaw behavior of delta, elliptical, and rectangular tail fins without a rotor and nacelle. The fins were released from initial yaw angles of -40 degrees and -80 degrees ; the latter is of sufficient magnitude to show the importance of the nonlinear yaw dynamics. Further, the friction in the model tail fin bearings was measured and modelled. The constants in the aerodynamic models were taken from the literature but significant improvement in accuracy is achieved by using system identification techniques to optimize the values. This leads to the third main finding: extended USBT is accurate for all generic tail fin shapes that we considered and is, therefore, very suitable for inclusion in aeroelastic codes for SWTs. The final development is of a general nonlinear equation for yaw response that is simpler than the extended USBT and is also suitable for inclusion in OpenFAST. The two nonlinear models are used to highlight the geometric requirements for good tail fin design.

distributed wind↗
NASA NTRSDate not supplied

Full-Envelope Aero-Propulsive Model Identification for Lift+Cruise Aircraft Using Computational Experiments

This paper describes a process utilizing computational fluid dynamics experiments to develop a reduced-order, integrated propulsion-airframe aerodynamic model for a lift+cruise electric vertical takeoff and landing (eVTOL) reference aircraft concept. eVTOL configurations exhibit aerodynamic characteristics of both fixed-wing and rotary-wing aircraft as well as complex phenomena, such as propulsion-airframe interactions. Consequently, conventional aircraft aerodynamic modeling strategies require modification when applied to these unique aircraft. A novel aero-propulsive modeling approach using design of experiments techniques and computational fluid dynamics simulations is postulated for modeling a lift+cruise aircraft configuration. Aero-propulsive models are developed throughout the operational flight envelope to enable continuous flight dynamics simulations from hover through forward flight. The model adequacy is assessed using validation data acquired separately from data used to identify the model and indicates that the models have sufficient predictive capability. Research findings are presented with a discussion of unique lift+cruise aircraft aerodynamic characteristics and practical strategies to inform future aero-propulsive modeling and simulation efforts for eVTOL aircraft.

lift+cruise↗
NASA NTRS2019

Performance Enhancement of the Flexible Transonic Truss-Braced Wing Aircraft Using Variable-Camber Continuous Trailing-Edge Flaps

Aircraft designers are to a growing extent using vehicle flexibility to optimize performance with objectives such as gust load alleviation and drag minimization. More complex aerodynamically optimized configurations may also require dynamic loads and perhaps eventually flutter suppression. This paper considers an aerodynamically optimized truss-braced wing aircraft designed for a Mach 0.745 cruise. The variable camber continuous trailing edge flap concept with a feedback control system is used to enhance aeroelastic stability. A linearized reduced order aerodynamic model is developed from unsteady Reynolds averaged Navier-Stokes simulations. A static output feedback controller is developed from that model. Closed-loop simulations using the reduced order aerodynamic model show that the controller is effective in stabilizing the vehicle dynamics.

Bartels, Robert E.↗
NASA NTRS2011

Development of the Dual Aerodynamic Nozzle Model for the NTF Semi-Span Model Support System

The recent addition of a dual flow air delivery system to the NASA Langley National Transonic Facility was experimentally validated with a Dual Aerodynamic Nozzle semi-span model. This model utilized two Stratford calibration nozzles to characterize the weight flow system of the air delivery system. The weight flow boundaries for the air delivery system were identified at mildly cryogenic conditions to be 0.1 to 23 lbm/sec for the high flow leg and 0.1 to 9 lbm/sec for the low flow leg. Results from this test verified system performance and identified problems with the weight-flow metering system that required the vortex flow meters to be replaced at the end of the test.

Jones, Greg S.↗
NASA NTRS1992

Improved two-equation k-omega turbulence models for aerodynamic flows

Two new versions of the k-omega two-equation turbulence model will be presented. The new Baseline (BSL) model is designed to give results similar to those of the original k-omega model of Wilcox, but without its strong dependency on arbitrary freestream values. The BSL model is identical to the Wilcox model in the inner 50 percent of the boundary-layer but changes gradually to the high Reynolds number Jones-Launder k-epsilon model (in a k-omega formulation) towards the boundary-layer edge. The new model is also virtually identical to the Jones-Lauder model for free shear layers. The second version of the model is called Shear-Stress Transport (SST) model. It is based on the BSL model, but has the additional ability to account for the transport of the principal shear stress in adverse pressure gradient boundary-layers. The model is based on Bradshaw's assumption that the principal shear stress is proportional to the turbulent kinetic energy, which is introduced into the definition of the eddy-viscosity. Both models are tested for a large number of different flowfields. The results of the BSL model are similar to those of the original k-omega model, but without the undesirable freestream dependency. The predictions of the SST model are also independent of the freestream values and show excellent agreement with experimental data for adverse pressure gradient boundary-layer flows.

Menter, Florian R.↗
NASA NTRS1993

Zonal Two Equation Kappa-Omega Turbulence Models for Aerodynamic Flows

Two new versions of the kappa-omega two-equation turbulence model will be presented. The new Baseline (BSL) model is designed to give results similar to those of the original kappa-omega model of Wilcox, but without its strong dependency on arbitrary freestream values. The BSL model is identical to the Wilcox model in the inner 50% of the boundary-layer but changes gradually to the standard kappa-epsilon model (in a kappa- omega formulation) towards the boundary-layer edge. The free shear layers. The second version of the model is called Shear-Stress Transport (SST) model. It is a variation of the BSL model with the additional ability to account for the transport of the principal turbulent shear stress in adverse pressure gradient boundary-layers. The model is based on Bradshaw's assumption that the principal shear-stress is proportional to the turbulent kinetic energy, which is introduced into the definition of the eddy-viscosity. Both models are tested for a large number of different flowfields. The results of the BSL model are similar to those of the original kappa-omega model, but without the undesirable freestream dependency. The predictions of the SST model are also independent of the freestream values but show better agreement with experimental data for adverse pressure gradient boundary-layer flows.

Menter, Florian R.↗
NASA NTRS1993

A model for rotorcraft flying qualities studies

This paper outlines the development of a mathematical model that is expected to be useful for rotorcraft flying qualities research. A computer model is presented that can be applied to a range of different rotorcraft configurations. The algorithm computes vehicle trim and a linear state-space model of the aircraft. The trim algorithm uses non linear optimization theory to solve the nonlinear algebraic trim equations. The linear aircraft equations consist of an airframe model and a flight control system dynamic model. The airframe model includes coupled rotor and fuselage rigid body dynamics and aerodynamics. The aerodynamic model for the rotors utilizes blade element theory and a three state dynamic inflow model. Aerodynamics of the fuselage and fuselage empennages are included. The linear state-space description for the flight control system is developed using standard block diagram data.

Mittal, Manoj↗
NASA NTRS1983

User's manual for master: Modeling of aerodynamic surfaces by 3-dimensional explicit representation

A system of computer programs was developed to model general three dimensional surfaces. Surfaces are modeled as sets of parametric bicubic patches. There are also capabilities to transform coordinates, to compute mesh/surface intersection normals, and to format input data for a transonic potential flow analysis. A graphical display of surface models and intersection normals is available. There are additional capabilities to regulate point spacing on input curves and to compute surface/surface intersection curves. Input and output data formats are described; detailed suggestions are given for user input. Instructions for execution are given, and examples are shown.

Gibson, S. G.↗
NASA NTRSDate not supplied

Validation of a Mid-Fidelity Approach for Aircraft Stability and Control Characterization

This paper describes an efficient computational approach for aircraft aerodynamic model development intended for use in flight dynamics simulations. A commercial surface-vorticity flow solver called FlightStream is employed to predict performance, stability, and control characteristics for a NASA subscale electric vertical takeoff and landing aircraft in its isolated-airframe configuration. A framework is described to rapidly convert OpenVSP geometry into a form compatible with the FlightStream software. FlightStream predictions for the variation of aerodynamic force and moment coefficients with airflow angles and control surface deflection angles are compared to static wind-tunnel data to illustrate the process and assess the accuracy of FlightStream solutions. The results and approach presented in this paper are encouraging for use in rapid aerodynamic modeling and flight dynamics simulation development early in the aircraft design process.

aerodynamic modeling↗