Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Perspectives on intrinsic toughening strategies and passivation of perovskite films with organic additives

We report on the inclusion of 5-aminovaleric acid (5-AVA)—a bulky, long-chained organic molecule—as an additive to enhance the mechanical integrity of hybrid perovskite films. We studied a range of organic cation additives and found that 5-AVA was the most effective at improving cohesion energy, a key metric of mechanical reliability. MAPbI 3 films reinforced with 5-AVA added in 5% concentration increased cohesion energy 12-fold from 0.53 J/m 2 to 6.04 J/m 2 , an effect which is attributed to increased plasticity and crack deflection around grain boundaries of the additive-containing perovskite. The addition of 5-AVA also improves V oc in perovskite solar cells and carrier lifetimes with a minimal decrease in PCE, attributed to passivation reducing defect and trap densities. A Tauc plot analysis of the bandgap shows that 5-AVA increases the band gap of the perovskite, correlating with reduced film stress compared to MAPbI 3 . Finally, the usage of 5-AVA improves the intrinsic thermomechanical reliability, but this improvement comes at the penalty of slightly reduced device efficiency due to reduced charge extraction from the presence of the bulky, insulating organic additive.

14 SOLAR ENERGY↗
DOE OSTI2023

Green Needle Coke Production from Pyrolysis Biocrude toward Bio-based Anode Material Manufacture: Biochar Fines Addition Effect as “Physical Template” on the Crystalline Order

Here, a new method for producing green needle coke (GNC) is developed by replacing the “heavy fraction” of petroleum pitch delayed coking with fast pyrolysis biocrude. A series of alternative biocrude distillation, carbonization, and calcination conditions were investigated to determine the influence of these processing parameters onto the crystalline structure of the resulting graphitized material. For the first time, the addition of biochar fines was found to serve as a “physical template” to increase the graphitic nature of the final product. During the initial biocrude carbonization (350–450 °C), volatile compounds are released, and aromatics in pyrolysis biocrude experience condensation, resulting in GNC solids with carbon contents above 95 wt % and some early lamellar structure. In the second stage of the thermal process (25–1500 °C), there are additional thermal decomposition reactions with an increase in the aromatic nature of the graphitized solid. It was found that systematic addition of biochar fines induces a nucleating effect during the GNC development. Thermogravimetric analysis suggests that biochar fines promote polycondensation reactions by modifying the biopitch structure and molecular weight, while elemental analysis (CHN) shows a reduction in both H/C and O/C ratios which are consistent with the increase in aromaticity and removal of oxygenated compounds as thermal treatment evolves. The effects of different bio-based pitch materials (after distillation) and GNC intermediates were evaluated by pyrolysis-gas chromatography mass spectrometry and Fourier transform infrared, displaying slight changes on product yields and quality. X-ray diffraction patterns taken after graphitization evidence an increase in the graphitic order with the addition of biochar fines. Transmittance electron microscopy depicts an improvement on graphitic morphology as biochar fine content increases. The use of biochar fines showed a significant increase in graphitic ordering at addition levels above 0.01 wt %. These results show that thermally treated biocrude/biochar fine systems can produce graphitic structures (hard carbon-like) that might be suitable for the manufacture of sodium-ion batteries.

09 BIOMASS FUELS↗
DOE OSTI2022

Strong yet ductile nanolamellar high-entropy alloys by additive manufacturing

Additive manufacturing produces net-shaped components layer by layer for engineering applications. The additive manufacture of metal alloys by laser powder bed fusion (L-PBF) involves large temperature gradients and rapid cooling, which enables microstructural refinement at the nanoscale to achieve high strength. However, high-strength nanostructured alloys produced by laser additive manufacturing often have limited ductility. In this work, we use L-PBF to print dual-phase nanolamellar high-entropy alloys (HEAs) of AlCoCrFeNi 2.1 that exhibit a combination of a high yield strength of about 1.3 gigapascals and a large uniform elongation of about 14 percent, which surpasses those of other state-of-the-art additively manufactured metal alloys. The high yield strength stems from the strong strengthening effects of the dual-phase structures that consist of alternating face-centred cubic and body-centred cubic nanolamellae; the body-centred cubic nanolamellae exhibit higher strengths and higher hardening rates than the face-centred cubic nanolamellae. The large tensile ductility arises owing to the high work-hardening capability of the as-printed hierarchical microstructures in the form of dual-phase nanolamellae embedded in microscale eutectic colonies, which have nearly random orientations to promote isotropic mechanical properties. The mechanistic insights into the deformation behaviour of additively manufactured HEAs have broad implications for the development of hierarchical, dual- and multi-phase, nanostructured alloys with exceptional mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure and properties of additively manufactured Al–Ce–Mg alloys

Additive manufacturing of aluminum alloys is largely dominated by a near-eutectic Al-Si compositions, which are highly weldable, but have mechanical properties that are not competitive with conventional wrought Al alloys. In addition, there is a need for new Al alloys with improved high temperature properties and thermal stability for applications in the automotive and aerospace fields. In this work, we considered laser powder bed fusion additive manufacturing of two alloys in the Al–Ce–Mg system, designed as near-eutectic (Al–11Ce–7Mg) and hyper-eutectic (Al–15Ce–9Mg) compositions with respect to the binary L → Al + Al 11 Ce eutectic reaction. The addition of magnesium is used to promote solid solution strengthening. A custom laser scan pattern was used to reduce the formation of keyhole porosity, which was caused by excessive vaporization due to the high vapor pressure of magnesium. The microstructure and tensile mechanical properties of the alloys were characterized in the as-fabricated condition and following hot isostatic pressing. The two alloys exhibit significant variations in solidification structure morphology. These variations in non-equilibrium solidification structure were rationalized using a combination of thermodynamic and thermal modeling. Both alloys showed higher yield strength than AM Al-10Si-Mg for temperatures up to 350 °C and better strength retention at elevated temperatures than additively manufactured Scalmaloy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Catalytic deconstruction of organic additive-containing plastics

Plastics waste ends up in landfills, oceans, and incinerators, posing major environmental and human health threats. Catalytic deconstruction is emerging as a key technological solution to handle complex plastics and has successfully converted virgin polymers into various products. Here, we investigate the resilience of chemical deconstruction technologies to organic additives, which are ubiquitous in plastics. We study catalyst-additive interactions experimentally and via first-principles calculations for plastics additives representative of entire classes. We reveal two deactivation mechanisms and demonstrate that many recently developed catalysts are inadequate for polyolefin conversion due to poisoning caused by the strong adsorption of most additives or their small fragments. Furthermore, we also identify conditions and catalysts that can circumvent the challenge of deconstruction in the presence of additives challenge.

10 SYNTHETIC FUELS↗
DOE OSTI2021

Toxicity of hydraulic fracturing wastewater from black shale natural-gas wells influenced by well maturity and chemical additives

Hydraulic fracturing of deep shale formations generates large volumes of wastewater that must be managed through treatment, reuse, or disposal. Produced wastewater liberates formation-derived radionuclides and contains previously uncharacterized organohalides thought to be generated within the shale well, both posing unknown toxicity to human and ecological health. Here, we assess the toxicity of 42 input media and produced fluid samples collected from four wells in the Utica formation and Marcellus Shale using two distinct endpoint screening assays. Broad spectrum acute toxicity was assessed using a bioluminescence inhibition assay employing the halotolerant bacterium Aliivibrio fischeri, while predictive mammalian cytotoxicity was evaluated using a N-acetylcysteine (NAC) thiol reactivity assay. The acute toxicity and thiol reactivity of early-stage flowback was higher than later produced fluids, with levels diminishing through time as the natural gas wells matured. Acute toxicity of early stage flowback and drilling muds were on par with the positive control, 3,5-dichlorophenol (6.8 mg L -1 ). Differences in both acute toxicity and thiol reactivity between paired natural gas well samples were associated with specific chemical additives. Samples from wells containing a larger diversity and concentration of organic additives resulted in higher acute toxicity, while samples from a well applying a higher composition of ammonium persulfate, a strong oxidizer, showed greater thiol reactivity, predictive of higher mammalian toxicity. Both acute toxicity and thiol reactivity are consistently detected in produced waters, in some cases present up to nine months after hydraulic fracturing. These results support that specific chemical additives, the reactions generated by the additives, or the constituents liberated from the formation by the additives contribute to the toxicity of hydraulic fracturing produced waters and reinforces the need for careful consideration of early produced fluid management.

03 NATURAL GAS↗
DOE OSTI2022

Optimizing Multi-Robot Placements for Wire Arc Additive Manufacturing

Wire arc additive manufacturing is a metal additive manufacturing process in which the material is deposited using arc welding technology. It is gaining popularity due to high material deposition rates and faster build time. It is en-abled using robotic manipulators and can build relatively large-scale parts faster when compared with other metal additive manufacturing processes. However, the size of the large-scale parts is limited by the size of the industrial manipulator being used for the process. This limitation is overcome by using a fixed configuration multi-robot cell in which manipulators work cooperatively to build large-scale parts quickly. A fixed multi-robot cell with closely spaced industrial manipulators has high flexibility, but it restricts the part size that can be built. If the manipulators are spread out, the cell loses its flexibility but can build relatively larger parts. This issue can be avoided by using larger size manipulators, which are expensive, or by moving the modest size manipulators based on the part geometries. This paper presents a novel algorithm to generate multi-robot placements for different part geometries to be built using wire arc additive manufacturing. Furthermore, the algorithm hierarchically optimizes the build time and the inverse kinematics consistency in robot paths to improve the process efficiency and part quality. We compare the results with fixed multi-robot cells and provide insights to users to make an informed decision on whether to use a fixed or a flexible multi-robot cell for wire arc additive manufacturing.

Bhatt, Prahar↗
DOE OSTI2021

Convection in Scaled Turbine Internal Cooling Passages With Additive Manufacturing Roughness

Abstract Additive manufacturing processes, such as direct metal laser sintering (DMLS), enable the creation of novel turbine cooling internal passages and systems. However, the DMLS method produces a significant and unique surface roughness. Previous work in scaled passages analyzed pressure losses and friction factors associated with the rough surfaces, as well as investigated the velocity profiles and turbulent flow characteristics within the passage. In this study, the heat transfer characteristics of scaled additively manufactured surfaces were measured using infrared (IR) thermography. Roughness panels were CNC machined from plates of aluminum 6061 to create near isothermal roughness elements when heated. Fluid resistance differences between the aluminum roughness panels and roughness panels constructed from ABS plastic using the same roughness patterns from McClain et al. (2020, “Flow in a Simulated Turbine Blade Cooling Channel With Spatially Varying Roughness Caused by Additive Manufacturing Orientation,” ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, Virtual Conference, Sept. 21–25, GT2020-16069) were investigated. Finally, the overall thermal performance enhancements and friction losses were assessed through the calculation of surface averaged “global thermal performance” ratios. The global thermal performance characterizations indicate results in-line with those found for traditional commercial roughness and slightly below traditional internal passage convection enhancement methods such as swirl chambers, dimples, and ribs. The passages investigated in this study do not include compressibility effects or the long-wavelength artifacts and channel geometric deviations observed by Wildgoose et al. (2020, “Impact of Additive Manufacturing on Internal Cooling Channels with Varying Diameters and Build Directions,” ASME Turbo Expo 2020, Turbomachinery Technical Conference and Exposition, Virtual Conference, Sept. 21–25, GT2020-15049). However, the results of this study indicate that, based on the roughness augmentation alone, artificial convective cooling enhancers such as turbulators or dimples may still be required for additively manufactured turbine component cooling.

Engineering↗
DOE OSTI2022

Design of a Scavenging Pyrrole Additive for High Voltage Lithium-Ion Batteries

We report 1-(dimethylamino) pyrrole (PyDMA) as an electrolyte additive for high voltage lithium-ion batteries based on LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622)//Graphite with an upper cutoff voltage of 4.4 V. Density Functional Theory (DFT) modeling indicates that the unique structure of PyDMA could be effective in preventing the hydrolysis of LiPF 6 in a carbonate electrolyte, mitigating issues related to HF formation. The calculations also indicated that the additive would oxidize at lower potentials than typical electrolyte solvents, which could lead to protective films at the cathode surface. These expectations were tested using Nuclear Magnetic Resonance (NMR) and extensive electrochemical characterization. NMR studies confirmed the superb dehydrating capability of PyDMA, which successfully prevents HF formation even at high water content. Addition of 0.5 wt% PyDMA resulted in improved capacity retention in full-cells, and also in lower levels of transition metal dissolution from the cathode. Incremental capacity (dQ/dV) analysis indicates that benefits of PyDMA at low concentration (0.5–1 wt%) are associated with decreased rates of Li + -trapping reactions, and that higher concentrations of the additive can lead to isolation of cathode domains. Furthermore, our study indicates that PyDMA could be a promising electrolyte additive for high voltage lithium-ion batteries at a low concentration.

25 ENERGY STORAGE↗
DOE OSTI2022

Performance of a Novel In-Situ Converted Additive for High Voltage Li-ion Pouch Cells

In search for new classes of additives for high voltage NMC/graphite lithium-ion cells, the precursor additive bis(trimethylsilyl) malonate (bTMSM) is shown to be activated via a spontaneous reaction with LiPF 6 and LiBF 4 salts in carbonate-based electrolyte to form lithium tetrafluoro(malonato)phosphate (LiTFMP), and lithium difluoro(malonato)borate (LiDFMB), respectively. The reaction schemes and rates were studied via NMR spectroscopy and GCMS. The effects of LiTFMP and LiDFMB on high voltage electrochemical performance were then examined up to 4.5 V in Li[Ni 0.4 Mn 0.4 Co 0.16 ]O 2 (NMC442)/graphite and Li[Ni 0.6 Mn 0.4 Co 0.0 ]O 2 (NMC/640)/graphite pouch cells using aggressive voltage-hold cycling, long-term charge/discharge cycling, storage experiments, electrochemical impedance spectroscopy, and gas evolution measurements. While in situ converted additives suffer from gassing issues due to the presence of trimethylfluorosilane (TMSF) gas, a side product of the in situ reaction of bTMSM with LiPF 6 , the cycling and storage capability for the activated additives under study shows competitive performance and controlled impedance when compared to other well-known high voltage additives. Micro X-ray fluorescence spectroscopy (μXRF) confirmed that LiTFMP successfully minimizes the rate of transition metal deposition on the surface of graphite apparently by forming a protective agent at the cathode surface, hence allowing for improved cycling performance at high voltages.

25 ENERGY STORAGE↗
DOE OSTI2020

Impacts of the Addition of Sodium Reactor Experiment (SRE) and DR-3 Fuel from H-Canyon to Tank 40 on Acid Stoichiometry and Hydrogen Production

H-Canyon plans to discard Sodium Reactor Experiment (SRE) material that is currently stored in Tanks 16.3 and 16.4. Savannah River Remediation (SRR) determined that a portion of the SRE material can be added to Sludge Batch 9 (SB9) in Tank 40 and the remainder will be added to Sludge Batch 10 (SB10) that is currently being prepared in Tank 51. A processing flowsheet for both the nitric-formic acid flowsheet and the nitric-glycolic acid flowsheet were previously developed for SB9 sludge-only and coupled operation with the Actinide Removal Process – Modular Caustic Side Solvent Extraction Unit (ARP-MCU) and the Salt Waste Processing Facility (SWPF). Due to the compositional change in Tank 40 after the addition of SRE material, it is necessary to determine the influence on the acid stoichiometry operating window and hydrogen production for SB9 processing. An assessment was completed to address the influence of an addition of SRE and DR-3 Fuel from H-Canyon on the chemistry of Tank 40, the defined acid stoichiometry window (with and without SWPF streams) for the nitric-formic and nitric-glycolic acid flowsheets, and the resulting influence of the hydrogen production. Hydrogen production during the SRAT/SME cycles consists of thermolytic, radiolytic, and catalytic hydrogen. For the nitric-formic acid flowsheet, catalytic hydrogen dominates the hydrogen production during DWPF operation mode for the SRAT and SME vessels. This report was written to summarize that assessment. No SRNL testing is needed prior to adding up to 7,100 additional gallons of SRE and DR-3 Fuel from H-Canyon to Tank 40. Also, the addition of SRE will not exceed the Shielded Cells reported values for catalytic hydrogen for either the nitric-formic acid flowsheet (Technical Safety Requirement (TSR) limit of 0.15 lb/h) or the nitric-glycolic acid flowsheet (TSR limit 0.024 lb/h). The addition of the ARP stream from SWPF and the use of the nitric-glycolic acid flowsheet are both expected to decrease hydrogen generation, leading to a larger safety margin in the CPC.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Assessment of the 3420 Building Filtered Exhaust Stack Sampling Probe Location: Stack Verification Following Fan and Air Blender Additions

The Pacific Northwest National Laboratory (PNNL) 3420 Building, which is part of the Physical Sciences Facility (PSF), houses radiological capabilities that results in the requirement that emissions monitoring must be conducted for potential radionuclides in the exhaust air discharge of this building. The air monitoring system is required to conform to Title 40 of the Code of Federal Regulations part 61 (40 CFR 61) Subpart H, which in turns requires a sampling probe in the exhaust stream to conform to the criteria of American National Standards Institute / Health Physics Society (ANSI/HPS) N13.1-2011, Sampling and Monitoring Releases of Airborne Radioactive Substances from the Stack and Ducts of Nuclear Facilities. To support the air emissions permit for the 3420 Building on the PNNL campus, stack testing that used computational fluid dynamics (CFD) modeling as a surrogate stack and verification tests of velocity uniformity and flow angle on the retrofitted facility stack was performed. The ANSI/HPS N13.1-2011 criteria for the air monitoring probe location are that velocity uniformity, gaseous tracer uniformity, and particulate tracer uniformity must be less than or equal to 20%COV. Furthermore, no point in the sampling location may have a gaseous tracer concentration that varies from the mean concentration by more than 30%. Additionally, the flow angle at the sampling location must not be more than 20°. The CFD modeling of the stack, as reported by Recknagle et al. (2018) demonstrated that the stack meets the criteria at the probe location. The velocity uniformity and flow angle results from the 3420 stack verification tests, performed in October 2020, demonstrated that the CFD model results may be used to support the qualification of the stack sampling location. The measured velocity uniformity verification test result was 1.4%COV. This value is well within the uniformity criterion, which is that the velocity uniformity be =20%COV. Additionally, this value is well within the criterion that the actual stack measurement must be within 5% of the surrogate stack result of 2.1%COV when all four fans were operating. Additionally, the measured average flow angle at the 3420 stack monitor location was 15.5 degrees. Although this is higher than expected based on the CFD model, the result is =20 degrees, so the criterion is met. Based on these stack verification test results, the reconfigured 3420 Building filtered exhaust stack meets the qualification criteria given in the ANSI/HPS N13.1-2011 standard. Further changes to the system configuration or operating conditions that are outside the bounds described in this and the CFD report (Recknagle et al., 2018) may require additional tests and additional analysis to determine compliance with the standard.

3420 Building↗
DOE OSTI2020

Development of Ionic Liquid-Additized, GF-5/6 Compatible Low-Viscosity Oils for Automotive Engine and Rear Axle Lubrication for 4% Improved Fuel Economy

This joint project among ORNL, GM, and DRO successfully developed ionic liquid-additized low viscosity lubricants, SAE 0W-12 and 70W-80, for both IC engine and rear axle lubrication, respectively, and demonstrated combined vehicle fuel economy improvement (FEI). Phosphonium-alkylphosphate ILs have been found to be the most effective among the candidates in protecting surface damage from both sliding wear and rolling contact fatigue, and optimal IL concentrations have been determined. The IL’s impact on three-way catalyst seems to be significantly less adverse than the conventional ZDDP. Oil formulations were optimized for both energy efficiency and wear protection. Tribological bench testing of the IL-additized low-viscosity oils showed at least 40% lower boundary friction, more than 60% lower elastohydrodynamic friction, and greater than 50% less wear compared with commercial baselines. IL-additized lubricants have demonstrated FEI by 9.9% in engine dynamometer tests under extreme conditions and 6.9% increased power output in gear rig tests. Prototype IL-additized engine oil and rear axle fluid exhibited combined FEI of 1.39% and 3.24% benchmarked against the state-of-the-art baselines in vehicle testing of fresh oils under the Federal Test Procedure (FTP) city cycle and Highway Fuel Economy Driving Schedule (HWFET), respectively. Used oil analysis suggested that the IL-additized low-viscosity oils produced less wear than the commercial baselines. The gained fundamental understanding and demonstrated FEI in this work pave the way for future development and implementation of the ionic liquid technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Study of Additive Manufacturing Applications to Geothermal Technologies Final Project Report

This report summarizes work performed to assess the potential for utilizing additive manufacturing (AM) to substantially improve either the availability, performance or cost basis for tools and components that are required for geothermal energy production. A systematic cataloging of geothermal activities, associated technologies, and current manufacturing methods was first undertaken. This included literature reviews as well as interviews with subject matter experts, service companies and OEMs. An industry workshop was held as part of this portion of the project to obtain input and concerns from a broad range of OEMs, service providers and end users. This workshop was also used to gage the current level of AM activity in industry, receptiveness to the use of AM manufactured parts, and any up front concerns that may exist. A summary of the workshop is presented in this report. Representative components and assemblies and their current manufacturing methods were then analyzed by additive manufacturing experts at a company called Senvol to determine the feasibility and required steps for producing parts by additive manufacturing. A step by step description of conventional manufacturing of the parts was also performed to establish a manufacturing baseline for comparison purposes. This analysis also considered and described the benefits of additively manufacturing the parts in terms of specific AM systems, material availability for AM, dimensional requirements and potential economic advantages. Details of the manufacturability assessment were summarized in a report which is included as a chapter in this document. The analysis of the AM subject matter experts was then be used by techno-economic analysts to perform a comparative economic evaluation of the manufacturing of select technologies by AM and conventional approaches. This activity leveraged ORNL expertise and prior experience in other applications. A framework based on assessing cost, volume production considerations, and time to manufacture was created to more easily discern the advantages or disadvantages of additive versus conventional manufacturing methods. The report concludes with a general assessment of the current applicability of AM for geothermal technologies, AM gaps and needs related to typical geothermal hardware, and the potential benefits and impacts of AM to geothermal energy production.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Computational Tools for Additive Manufacture of Tailored Microstructure and Properties

Additive manufacturing has the potential to revolutionize industrial hardware and unlock efficiency gains through the fabrication of geometries and architectures not possible by conventional processing. Currently most additive builds use a single set of process parameters (e.g. laser power and scan speed) which results in a part with a homogenous microstructure that provides a singular performance level. To move beyond this state, Raytheon Technologies Research Center worked to create a set of computational tools to track material evolution through each step of the additive process. Computational fluid dynamics and phase field models for microstructure evolution as a function of processing parameters, and crystal plasticity models fully coupling microstructure and mechanical properties for performance predictions were leveraged to establish a connection between additive parameters and the final microstructure. This framework was utilized to tailor spatially-varying mechanical properties in a part by appropriately controlling the microstructure evolution during the additive process. Specifically, a turbine blade was 3D printed from nickel superalloy IN718 using laser powder bed fusion with coarse grains in the airfoil section which experiences the highest temperatures and is creep limited while finer grains were printed in the root of the blade which experience higher stresses but at lower temperatures and is therefore fatigue limited. The benefit of being able to intentionally insert coarse grains in the high temperature region of the blade was showcased with a microstructure sensitive creep model that indicates longer creep life for coarser grains.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Integral Experiment Final Design for Thermal/Epithermal eXperiments (TEX) Plutonium Additional Mixed Spectrum Configurations

This report presents the final design (CED-2) for three additional mixed-spectra configurations for plutonium Thermal/Epithermal eXperiments (TEX) to target the intermediate energy region (IER-553). The baseline cases of IER-184 (PU-MET-MIXED-002 [2]) spanned the entire fission energy spectrum. Case 3, which had a median fission energy (MFE) of approximately 6E-5 MeV and had a fission fraction of about 42% in the intermediate energy range, resulted in a $k_{eff}$ overestimation of 1.1%. Compared to 749 previous ICSBEP plutonium benchmarks, the baseline cases accurately predicted the experiments in the thermal and fast regions where the majority of benchmarks inhabit. The benchmarks in the intermediate energy region to date are sparse and overestimate $k_{eff}$ with an average C/E between 1.02 and 1.03. The additional proposed configurations span the whole of the intermediate energy region. The experimental design utilizes the plutonium/aluminum metal alloy Zero Power Physics Reactor (ZPPR) Plutonium-Aluminum No-Nickel (PANN) plates with varying polyethylene moderator thicknesses to span the intermediate fission energy region. Each of the cases have varying fractions of thermal, intermediate, and fast fissions. The designs were chosen to maximize the intermediate energy fraction. The experiment will take place on the universal critical assembly machine, Planet. The layers will be split as equally as possible between the lower platen and the upper stationary platform of Planet. The upper half of the experimental configuration will also have an upper reflector of polyethylene of specified thicknesses to achieve criticality when the lower platen is raised fully. The previous IER-184 configurations, specifically Case 3, were used to determine the configurations for the additional experiments and neutronics calculations were used to fine-tune the configurations to ensure criticality. The quadrature sum uncertainty in Δ$k_{eff}$ for Case 3 in PU-MET-MIXED-002 was found to be 0.00219. Section 3.8 gives a detailed description of the uncertainties calculated. The additional configurations, which are based directly on Case 3, are expected to have similar uncertainties. However, it is possible to reduce the overall uncertainty of Δ$k_{eff}$ for the additional configurations using the knowledge obtained from the calculations in the benchmark.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Use of Modeling and Experiments to Assess the Effect of Minor Alloying Additions on Alumina Scale Formation during High-Temperature Oxidation

During the last decades, new generations of Ni-based superalloys have emerged with judiciously controlled chemistries. These alloys heavily rely on the addition of refractory elements to enhance their mechanical properties at elevated temperatures; however, a clear interpretation of the influence of these minor-element additions on the alloy's high-temperature oxidation behavior is still not well understood, particularly from the standpoint of predicting the transition from internal to external alumina formation. In this context, the present investigation describes a systematic study that addresses the intrinsic effects that minor element additions of Nb, Ta, and Re have on the oxidation behavior of alumina-scale forming γ-Ni alloys. By combining a novel simulation approach with high-temperature oxidation experiments, the present study evidences the generally positive effect associated with 2 at. % addition of Ta and Re as well as the detrimental consequences of Nb additions on the 1100 °C oxidation of (in at. %) Ni-6Al-(0,4,6,8)Cr alloys.

Rodriguez, Rafael↗
NASA NTRS1972

Effects of additives on volume change on melting, surface tension, and viscosity of liquid aluminum oxide

The effects of various oxide additives on the volume change on melting, the surface tension, and the viscosity of liquid Al2O3 were studied. Additives of Sm2O3, MgO, and Y2O3 which form solid solutions, compounds, and multiphase solids with Al2O3 were studied. A review of the property data for Al2O3 and Al2O3 containing oxide additives is presented. Oxide additives to Al2O3 reduce the volume change on melting and with the exception of SiO2 lower the viscosity; surface tensions change with oxide additives, but changes vary with different container material. Viscosity and volume change on melting appeared to be significantly more important for studying the properties of liquid oxides than surface tension. Supercooling of 270 K of yttrium aluminum garnet was observed.

Bates, J. L.↗