Results for “Unmanned Aerial” — Page 12

NASA NTRSDate not supplied

Enhancing Fault Isolation for Health Monitoring of Electric Aircraft Propulsion by Embedding Failure Mode and Effect Analysis into Bayesian Networks

This paper describes a fault isolation approach for electric powertrains of unmanned aerial vehicles. The approach leverages the combination of failure mode and effect analysis (FMEA) and Bayesian networks, thus introducing depend-ability structures into a diagnostic framework. Faults and failure events from the FMEA are mapped within a Bayesian network, where network edges replicate the links embedded within FMEAs. This framework helps the fault isolation process by identifying the probability of occurrence of specific faults or root causes given evidence observed through sensor signals. The framework is applied to an electric power-train system of a small, rotary-wing unmanned aerial vehicle, demonstrating how a Bayesian network enhanced by FMEA helps disambiguate between root causes of incipient failures, which would otherwise be considered as equally probable.

Fault Isolation↗

DOE OSTI2020

SPRUCE Experimental Plot Top View Aerial Images beginning June 2019

This data set provides a record of the aerial images of the SPRUCE experimental plots obtained periodically using an unmanned aerial vehicle (UAV) with attached camera from 2019-05-05- to 2022-08-25. New images of the plots will be added periodically. The initial RGB images may be used for studies of greenness and snow coverage and compared with ground-based measurements and chamber-based tree and shrub Phenocam images (e.g. Schädel et al., 2022). Also included are NDVI (Normalized Difference Vegetation Index) images showing calculated difference between visible near-infrared (NIR) light reflectance from vegetation, as well as infrared (IR) and multispectral images. Files are presented in JPEG (*.jpg) or PDF (*.pdf) format inside of 28 compressed (*.zip) files. Images were collected for the 10 plots with enclosures, the 7 unchambered plots, and the environmental monitoring instrument cluster area. Images are slightly off-plot center at 12 to 15 meters above ground level or approximately 2 meters above the top of an experimental chamber.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRSDate not supplied

Examining the Role of IMU Health Characterization and Monitoring in UAS Safety

Inertial measurement units (IMUs) can be vital for vehicle attitude and position estimation in unmanned aerial vehicles (UAVs). Degradation in these units could result in incorrect position estimates that are utilized in vehicle control, trajectory prediction, and other critical systems; however, the modes and effects of degradation in these IMUs are not well understood. In order to quantify the risk posed by degradation in these sensors, a study was conducted on the types of IMUs prevalent in the commercial market, their known failure modes, and the applicability to health monitoring methods for risk reduction and increased safety in an increasingly autonomous airspace. First, use cases and failure modes of the various types and reliability of commercially available IMUs were reviewed, and knowledge gaps and issues in the field were identified. Noting that inexpensive and lightweight MEMS (Microelectromechanical Systems) IMUs are some of the most commonly used but least reliable sensors in sUAS (small Unmanned Aerial Systems), five inexpensive MEMS IMUs were chosen for a performance evaluation study, selected from the Pixhawk autopilot systems, hobby sUAS, and prior NASA experimental studies. For each of these IMUs, a 10-minute bias test and a 12-hour drift test were performed for the accelerometers in a benchtop setting, using a BeagleBone Black for data collection. Using these results, the sensors’ performance is compared to their reported specifications, and the utility of implementing diagnostic methods for MEMS IMUs for research and commercial applications is evaluated. The paper concludes with a planned study for the evaluation of vibration-induced degradation for the selected sensors.

IMUs↗

NASA NTRS2019

Usability Test of a Prototype UAS Awareness Interface for Public Users

A tool to give the public a window into Unmanned Aerial Systems (UAS) Traffic Management (UTM) operations was created from an existing data collection tool. The interface included a map and a table showing details about UAS operations that could be queried in a number of ways. Eleven participants attended the study, successfully completing a 19-item task set in about 30 minutes. They correctly found information for 87% of the non-subjective tasks at a rate of around a minute per task, and rated the usability of the tool at the end of the session above the industry benchmark. Participants gave favorable reviews of the "public portal tool", even reporting that they would be satisfied with less information that it presented. There were one or two elements of the display that users found distracting and some navigation functions that need improvement, but on balance, the public representatives liked the features they saw in, and had few criticisms of, the public portal tool. One important issue for the small Unmanned Aerial System community to resolve will be how much or how little information should be available about UTM operations to members of the public.

Martin, Lynne H.↗

NASA NTRS2019

Usability Test of a Prototype UAS (Unmanned Aircraft Systems) Awareness Interface for Public Users

A tool to give the public a window into Unmanned Aerial Systems (UAS) Traffic Management (UTM) operations was created from an existing data collection tool. The interface included a map and a table showing details about UAS operations that could be queried in a number of ways. Eleven participants attended the study, successfully completing a 19-item task set in about 30 minutes. They correctly found information for 87% of the non-subjective tasks at a rate of around a minute per task, and rated the usability of the tool at the end of the session above the industry benchmark. Participants gave favorable reviews of the "public portal tool", even reporting that they would be satisfied with less information that it presented. There were one or two elements of the display that users found distracting and some navigation functions that need improvement, but on balance, the public representatives liked the features they saw in, and had few criticisms of, the public portal tool. One important issue for the small Unmanned Aerial System community to resolve will be how much or how little information should be available about UTM operations to members of the public.

Martin, Lynne H.↗

NASA NTRS2017

UAV Inspection of Electrical Transmission Infrastructure with Path Conformance Autonomy and Lidar-Based Geofences NASA Report on UTM Reference Mission Flights at Southern Company Flights November 2016

Flights at low altitudes in close proximity to electrical transmission infrastructure present serious navigational challenges: GPS and radio communication quality is variable and yet tight position control is needed to measure defects while avoiding collisions with ground structures. To advance unmanned aerial vehicle (UAV) navigation technology while accomplishing a task with economic and societal benefit, a high voltage electrical infrastructure inspection reference mission was designed. An integrated air-ground platform was developed for this mission and tested in two days of experimental flights to determine whether navigational augmentation was needed to successfully conduct a controlled inspection experiment. The airborne component of the platform was a multirotor UAV built from commercial off-the-shelf hardware and software, and the ground component was a commercial laptop running open source software. A compact ultraviolet sensor mounted on the UAV can locate 'hot spots' (potential failure points in the electric grid), so long as the UAV flight path adequately samples the airspace near the power grid structures. To improve navigation, the platform was supplemented with two navigation technologies: lidar-to-polyhedron preflight processing for obstacle demarcation and inspection distance planning, and trajectory management software to enforce inspection standoff distance. Both navigation technologies were essential to obtaining useful results from the hot spot sensor in this obstacle-rich, low-altitude airspace. Because the electrical grid extends into crowded airspaces, the UAV position was tracked with NASA unmanned aerial system traffic management (UTM) technology. The following results were obtained: (1) Inspection of high-voltage electrical transmission infrastructure to locate 'hot spots' of ultraviolet emission requires navigation methods that are not broadly available and are not needed at higher altitude flights above ground structures. (2) The sensing capability of a novel airborne UV detector was verified with a standard ground-based instrument. Flights with this sensor showed that UAV measurement operations and recording methods are viable. With improved sensor range, UAVs equipped with compact UV sensors could serve as the detection elements in a self-diagnosing power grid. (3) Simplification of rich lidar maps to polyhedral obstacle maps reduces data volume by orders of magnitude, so that computation with the resultant maps in real time is possible. This enables real-time obstacle avoidance autonomy. Stable navigation may be feasible in the GPS-deprived environment near transmission lines by a UAV that senses ground structures and compares them to these simplified maps. (4) A new, formally verified path conformance software system that runs onboard a UAV was demonstrated in flight for the first time. It successfully maneuvered the aircraft after a sudden lateral perturbation that models a gust of wind, and processed lidar-derived polyhedral obstacle maps in real time. (5) Tracking of the UAV in the national airspace using the NASA UTM technology was a key safety component of this reference mission, since the flights were conducted beneath the landing approach to a heavily used runway. Comparison to autopilot tracking showed that UTM tracking accurately records the UAV position throughout the flight path.

Moore, Andrew J.↗

DOE OSTI2025

Optimizing Deep Learning Models for Climate-Related Natural Disaster Detection from UAV Images and Remote Sensing Data

This research study utilized artificial intelligence (AI) to detect natural disasters from aerial images. Flooding and desertification were two natural disasters taken into consideration. The Climate Change Dataset was created by compiling various open-access data sources. This dataset contains 6334 aerial images from UAV (unmanned aerial vehicles) images and satellite images. The Climate Change Dataset was then used to train Deep Learning (DL) models to identify natural disasters. Four different Machine Learning (ML) models were used: convolutional neural network (CNN), DenseNet201, VGG16, and ResNet50. These ML models were trained on our Climate Change Dataset so that their performance could be compared. DenseNet201 was chosen for optimization. All four ML models performed well. DenseNet201 and ResNet50 achieved the highest testing accuracies of 99.37% and 99.21%, respectively. This research project demonstrates the potential of AI to address environmental challenges, such as climate change-related natural disasters. This study’s approach is novel by creating a new dataset, optimizing an ML model, cross-validating, and presenting desertification as one of our natural disasters for DL detection. Three categories were used (Flooded, Desert, Neither). Our study relates to AI for Climate Change and Environmental Sustainability. Drone emergency response would be a practical application for our research project.

AI↗

NASA NTRS2017

Center Overview and UAV Highlights at NASA Ames Research Center

The PowerPoint presentation gives an overview of NASA Ames Research Center and its core competencies, as well as some of the highlights of Unmanned Aerial Vehicle (UAV) and Unmanned Aircraft Systems (UAS) accomplishments and innovations by researchers at Ames.

Unmanned Aircraft Systems↗

NASA NTRSDate not supplied

Achieving Equilibrium for Dense, Integrated, Vehicle Navigation

Drone usage has proliferated in recent years with many applications that have market-changing potential. Applications that include parcel delivery, wildlife protection, precision farming, law enforcement, and industrial inspection, just to name a few. In this paper, the term drone is used to mean both Unmanned Aerial Vehicle and small Unmanned Aircraft System vehicles. Flight infrastructure can currently only support a few thousand aircraft flying over the United States National Airspace System (NAS) at any given time. A delay atone airport sends ripple effects through the system, causing more delays and missed connections. Once regulations and safety policies are put in place to allow for the widespread use of unmanned drones, the number of aircraft in the NAS is expected to skyrocket to millions, potentially congesting the airspace resulting in possible separation violations. In air traffic control, separation is the concept of keeping an “ownship” aircraft outside a minimum distance from “intruder” aircraft to reduce the risk of the aircraft colliding, as well as preventing accidents due to secondary factors, such as wake turbulence. Maintaining proper separation is a safety critical property for drones in the airspace. This paper addresses separation in time and in distance for high volume corridors (en-route) and lanes(on ground). The requirements and necessary conditions for maintaining proper separation and reaching maximum throughput for a given corridor/lane are addressed assuming unidirectional corridors/lanes where an aircraft arrives from one side and departs from the opposite side. Simulation results are presented that show the presented solution guarantees a set of drones to reach the equilibrium state by adjusting their speed based on their distance to the aircraft in front of them. The equilibrium state is defined as a state when a set of n aircraft moving at a relatively constant speed and uniform spacing from each other in a congested system. A congested system is defined as a state when the aircraft cannot move at their maximum allowed speed. Unlike existing centralized and pre-planned approaches, the proposed solution is fully distributed and enables autonomous aircraft to decide to adjust their speed and distance with respect to the preceding aircraft, dynamically. Simulation results are presented that assess the feasibility of the approach using a large number of drones and evaluate the scalability of the proposed solution.

Mahyar R. Malekpour↗

NASA NTRS2022

Preliminary Airfoil Design for Low Reynolds Numbers

Advances in the fields of electronics, batteries, and electric motors have enabled broad adoption of small-scale aircraft for various terrestrial applications. Numerous Micro Aerial Vehicles (MAVs) and small Unmanned Aerial Vehicles (UAVs), both civil and military, are in use today. Operation at their design flight condition often requires rotors, propellers, or wings to perform at Reynolds numbers significantly below 500,000 [1]. Airfoil performance at low Reynolds numbers is generally characterized by low aerodynamic performance (i.e. the attainable lift-to-drag ratio) compared to performance of airfoils at higher Reynolds numbers. The critical chord-based Reynolds number for conventional airfoils lies around Rec = 100,000 to Rec = 500,000 [2]. Below this critical Reynolds number, laminar separation of the boundary layer is usually the cause for poor performance. Researchers have found that below the critical Reynolds number, flat and cambered plates can outperform smooth airfoils. Circular-arc cambered plates especially have remarkable performance advantages compared to conventional airfoil shapes [3].

airfoil↗

NASA NTRSDate not supplied

A Strategic Approach for Dense, Integrated, Vehicle Navigation

Drone usage has been on the rise in recent years with applications that include parcel delivery, wildlife protection, precision farming, law enforcement, and industrial inspection, just to name a few. Once regulations and safety policies are put in place to allow for the widespread use of unmanned drones, the number of aircraft in the National Airspace System (NAS) is expected to skyrocket to millions, potentially congesting the airspace which increases the likelihood of separation violations and possibly incidents. Currently, flight infrastructure can only support a few thousand aircraft flying over the United States National Airspace System (NAS) at any given time. A delay at one airport can send ripple effects throughout the system, causing more delays and missed connections. In air traffic control, separation is the concept of keeping an “ownship” aircraft outside a minimum distance from “intruder” aircraft to reduce the risk of the aircraft colliding, as well as preventing accidents due to secondary factors, such as wake turbulence. Maintaining proper separation is often a safety critical property for fixed-wing drones in the airspace. This paper addresses drone separation in time and distance for high volume corridors (en route) and lanes (on ground), merging as well as crossing intersections of multiple corridors/lanes. In this paper, the term drone is applied to both Unmanned Aerial Vehicle (UAV) and small Unmanned Aircraft System (UAS) vehicles operating autonomously. There exists a gamut of approaches to the merging and crossing problems. At one end of the extreme are the conservative yet low cost and verifiable solutions of today that deal with two drones at a time. At the other end are complex Machine Learning-based solutions with high computing requirements for fully autonomous drones of the future that are expected to handle all contentions. This paper presents a feasible and verifiable strategic approach to these problems that is based on distributed cooperation between the drones and the infrastructure. Three phases of the strategic approach (Prepare, Adjust, Commit) are presented. Simulation results are presented that show the proposed approach is stable and resilient to induced perturbations and guarantees a set of fixed-wing drones to merge and cross intersections by adjusting their speed based on their distance to the aircraft in front of them while remaining in the equilibrium state. The equilibrium state is defined as the state when a set of n aircraft move at a relatively constant speed and uniform spacing from each other in a congested system. A congested system is defined as the state when at least one aircraft cannot move at its maximum allowed speed. Unlike existing centralized and pre-planned approaches, the proposed solution is fully distributed and enables autonomous aircraft to decide to adjust their speed and distance with respect to the preceding aircraft, dynamically. Simulation results are presented that assess the feasibility of the approach.

Distributed↗

NASA NTRSDate not supplied

A Strategic Approach for Dense, Integrated, Vehicle Navigation

Drone usage has been on the rise in recent years with applications that include parcel delivery, wildlife protection, precision farming, law enforcement, and industrial inspection, just to name a few. Once regulations and safety policies are put in place to allow for the widespread use of unmanned drones, the number of aircraft in the National Airspace System (NAS) is expected to skyrocket to millions, potentially congesting the airspace which increases the likelihood of separation violations and possibly incidents. Currently, flight infrastructure can only support a few thousand aircraft flying over the United States National Airspace System (NAS) at any given time. A delay at one airport can send ripple effects throughout the system, causing more delays and missed connections. In air traffic control, separation is the concept of keeping an “ownship” aircraft outside a minimum distance from “intruder” aircraft to reduce the risk of the aircraft colliding, as well as preventing accidents due to secondary factors, such as wake turbulence. Maintaining proper separation is often a safety critical property for fixed-wing drones in the airspace. This paper addresses drone separation in time and distance for high volume corridors (en route) and lanes (on ground), merging as well as crossing intersections of multiple corridors/lanes. In this paper, the term drone is applied to both Unmanned Aerial Vehicle (UAV) and small Unmanned Aircraft System (UAS) vehicles operating autonomously. There exists a gamut of approaches to the merging and crossing problems. At one end of the extreme are the conservative yet low cost and verifiable solutions of today that deal with two drones at a time. At the other end are complex Machine Learning-based solutions with high computing requirements for fully autonomous drones of the future that are expected to handle all contentions. This paper presents a feasible and verifiable strategic approach to these problems that is based on distributed cooperation between the drones and the infrastructure. Three phases of the strategic approach (Prepare, Adjust, Commit) are presented. Simulation results are presented that show the proposed approach is stable and resilient to induced perturbations and guarantees a set of fixed-wing drones to merge and cross intersections by adjusting their speed based on their distance to the aircraft in front of them while remaining in the equilibrium state. The equilibrium state is defined as the state when a set of n aircraft move at a relatively constant speed and uniform spacing from each other in a congested system. A congested system is defined as the state when at least one aircraft cannot move at its maximum allowed speed. Unlike existing centralized and pre-planned approaches, the proposed solution is fully distributed and enables autonomous aircraft to decide to adjust their speed and distance with respect to the preceding aircraft, dynamically. Simulation results are presented that assess the feasibility of the approach.

Distributed↗

DOE OSTI2021

Ensuring reliable connectivity to cellular-connected UAVs with up-tilted antennas and interference coordination

To integrate unmanned aerial vehicles (UAVs) in future large-scale deployments, a new wireless communication paradigm, namely, the cellular-connected UAV has recently attracted interest. However, the line-of-sight dominant air-to-ground channels along with the antenna pattern of the cellular ground base stations (GBSs) introduce critical interference issues in cellular-connected UAV communications. In particular, the complex antenna pattern and the ground reflection (GR) from the down-tilted antennas create both coverage holes and patchy coverage for the UAVs in the sky, which leads to unreliable connectivity from the underlying cellular network. To overcome these challenges, in this paper, we propose a new cellular architecture that employs an extra set of co-channel antennas oriented towards the sky to support UAVs on top of the existing down-tilted antennas for ground user equipment (GUE). To model the GR stemming from the down-tilted antennas, we propose a path-loss model, which takes both antenna radiation pattern and configuration into account. Next, we formulate an optimization problem to maximize the minimum signal-to-interference ratio (SIR) of the UAVs by tuning the up-tilt (UT) angles of the up-tilted antennas. Since this is an NP-hard problem, we propose a genetic algorithm (GA) based heuristic method to optimize the UT angles of these antennas. After obtaining the optimal UT angles, we integrate the 3GPP Release-10 specified enhanced inter-cell interference coordination (eICIC) to reduce the interference stemming from the down-tilted antennas. Our simulation results based on the hexagonal cell layout show that the proposed interference mitigation method can ensure higher minimum SIRs for the UAVs over baseline methods while creating minimal impact on the SIR of GUEs.

3GPP↗

NASA NTRS2008

Generic Helicopter-Based Testbed for Surface Terrain Imaging Sensors

To be certain that a candidate sensor system will perform as expected during missions, we have developed a field test system and have executed test flights with a helicopter-mounted sensor platform over desert terrains, which simulate Lunar features. A key advantage to this approach is that different sensors can be tested and characterized in an environment relevant to the flight needs prior to flight. Testing the various sensors required the development of a field test system, including an instrument to validate the truth of the sensor system under test. The field test system was designed to be flexible enough to cover the test needs of many sensors (lidar, radar, cameras) that require an aerial test platform, including helicopters, airplanes, unmanned aerial vehicles (UAV), or balloons. To validate the performance of the sensor under test, the dynamics of the test platform must be known with sufficient accuracy to provide accurate models for input into algorithm development. The test system provides support equipment to measure the dynamics of the field test sensor platform, and allow computation of the truth position, velocity, attitude, and time.

Alexander, James↗

DOE OSTI2024

A framework to enhance disaster debris estimation with AI and aerial photogrammetry

This study addresses the critical need to enhance disaster preparedness and response, focusing on hurricane impact assessment and debris estimation. Accurate assessments in this context are critical for post-event search-and-rescue (SAR) operations and resource distribution. Recent computing advancements are revealing the potential of unmanned aerial vehicles (UAVs) and artificial intelligence (AI) technologies in collecting data and assisting with post-hurricane reconnaissance. However, the use of AI and UAV photogrammetry for accurate disaster impact analysis remains underexplored. To this end, this study proposes a damage and debris analysis framework harnessing reality capture through aerial imagery and photogrammetry. Within this framework, a region-based neural network is leveraged to detect debris locations in aerial imagery with favorable performance. In a testbed within the Beaumont-Port Arthur region, in Southeast Texas, this study performs 3D reality captures of the built environment. Since the accuracy of the 3D reality capture is of importance in research areas associated with time-sensitive disaster response, we further investigate the optimal 2D aerial imagery overlap ratio required to generate a sufficiently accurate 3D model for disaster impact analysis and debris volume estimation. Results indicate that, in the case of aerial imagery for infrastructure systems, a minimum of 60 % overlap is recommended for damage assessment and debris analysis. In contrast, for flat green areas, a minimum of 50 % overlap is adequate. Overall, for disaster response applications, our study reveals that an overlap ratio between 60 % and 70 % is optimal for achieving a balance between time efficiency and data quality in aerial data collection. Furthermore, these quantitative recommendations are crucial for enabling efficient disaster response efforts. Additionally, our study outcomes will improve disaster impact analysis and facilitating timely and effective response strategies.

Artificial intelligence↗

DOE OSTI2021

ARM Aerial Facility (AAF) - Unmanned Aircraft Systems CO2/H2O Analyzer

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

ARM Aerial Facility (AAF) - Unmanned Aircraft Systems, Filter Sampler

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS2007

CIRA: Cooperative Institute for Research in the Atmosphere Newsletter, Volume 28, Fall 2007

The articles in this issue of the Cooperative Institute for Research in the Atmosphere (CIRA) Newsletter are: "Unmanned Aerial Systems: An Overview of NOAA's Unmanned Aircraft System Program," "International Activities: Weather Briefings and Training Via the Internet," "Cloudsat's One-Year Anniversary: An Abundance of Exciting New Cloud Observations," and "The Migration of NCAR'S Auto-Nowcaster into NWS AWIPS."

McInnis-Efaw, Mary↗