Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “UO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Direct isotopic analysis of solid uranium particulates on cotton swipes by microextraction-ICP-MS

Direct isotope ratio analysis of solid uranium particulates on cotton swipes was achieved using a solution-based microextraction technique, coupled to a quadrupole inductively coupled plasma - mass spectrometer (ICP-MS). This microextraction-ICP-MS methodology provides rapid isotopic analysis which could be applicable to nuclear safeguards measurements. Particulates of uranyl nitrate hexahydrate (UO 2 (NO 3 ) 2 ·6H 2 O) and uranyl fluoride (UO 2 F 2 ) ranging from 6 μm to 40 μm in length were transferred to cotton swipes with a particle manipulator. The microextraction probe then delivers a 5% nitric acid (HNO3) solvent onto the swipe surface to extract the uranium species. The extracted sample is then delivered to the ICP-MS for isotopic determination. The majority of uranium signal (~99% and ~94% for UO2(NO3)2·6H2O and UO 2 F 2 , respectively) was detected in the first 15 s extraction, while subsequent extractions on the same location had low or no U signal, suggesting near complete removal of the solid uranium compounds from the swipe surface. Ten samples (for each of the uranium compounds), were analyzed for their isotopic composition. For UO 2 (NO 3 ) 2 ·6H 2 O, the determined isotope ratios resulted in a % relative difference (% RD) from the referenced isotope ratios of 0.97, 1.0, and 7.3% for 234 U/ 238 U, 235 U/ 238 U, and 236 U/ 238 U, respectively. The % RD of the UO 2 F 2 isotope ratios were 1.9 and 0.60% for 234 U/ 238 U and 235 U/ 238 U, respectively. The preliminary limits of detection were determined to be 0.002, 0.4, and 60 pg for 234 U, 235 U and 238 U, respectively This work demonstrates that microextraction ICP-MS is a rapid and sensitive method that could directly determine uranium isotope ratios of UO 2 (NO 3 ) 2 ·6H 2 O and UO 2 F 2 particulates on cotton swipes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Nuclear fuels for transient test reactors

Transient test reactors with the ability to test fissile specimens under extreme conditions have been crucial tools in the development of nuclear technologies. Less than 10 unique facility designs have ever been constructed, most of which remain operational today and still use the original nuclear fuel constructed for them more than 40 years ago. Historic fuel systems for transient test reactors vary in significant ways which have marked influences on reactor capabilities. Eventually, new fuel will be needed to support the longevity of transient test reactor missions. This paper reviews precedent transient reactor fuel systems in the context of their unique requirements. A few key conclusions are illustrated by comparing and contrasting these transient test reactors. Fuel composites which are mostly graphite can enable transient reactors with very high neutron fluence capability (>2E16 n/cm 2 ) and are amenable to longer “shaped” transients but cannot achieve pulses <10 ms in duration. Reducing the graphite-to-uranium ratio can yield a very narrow pulse capability but delivers less fluence and requires cores with considerably more fissile material. Designs based on uranium dioxide (UO 2 ) make use of readily available materials to create compact cores with narrow pulse width capabilities but with moderate neutron fluence capabilities (~2E15 n/cm 2 ). Uranium zirconium hydride (U-ZrHx) is a well-established fuel system for pulsing reactors which has been intermittently manufactured throughout the decades. U-ZrHx offers similar capabilities to UO 2 designs in terms of nuclear kinetics, but with about half the fluence capability (~1E15 n/cm 2 ). An evolution of the UO 2 system, termed “ternary ceramic” fuel, shows that dispersing UO 2 in zirconium oxide and calcium oxide can increase fluence capability greatly (~7E15 n/cm 2 ), but is not presently a commonly available fuel form. A unique composite of UO 2 and beryllium oxide (UO 2 -BeO) can be used to create a core with similar kinetics and compact core geometry as U-ZrHx designs, but with significantly higher fluence capability (~6E15 n/cm 2 ). Like ternary ceramic fuel, newly fabricated UO 2 -BeO would require reestablishing its historic manufacturing process which would be further complicated by the health hazards associated with beryllium. In conclusion, like most engineering problems, there is no perfect solution, but this paper outlines the advantages and disadvantages of candidate fuel options to help guide detailed evaluations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Chromium-doped uranium dioxide fuels: A review

UO 2 doped with parts per million CR 2 O 3 powder is considered a potential near term accident tolerant fuel candidate. Here, the results of decades of industry and academic research into Cr-doped UO 2 are analyzed and their shortcomings are critiqued. Focusing on the incorporation mechanisms of Cr into the fuel matrix, we explore a mechanistic understanding of the characteristic properties of Cr-doped UO 2 , notably, enhanced fission gas retention attributed to enlarged grain sizes following sintering, along with marginal improvements in the thermophysical properties. The findings of recent X-ray Adsorption Near Edge Spectroscopy studies were compared and put into conversation with historic data regarding the incorporation of Cr in UO 2 . On the basis of defect mechanisms, the case is made for the substitutional incorporation of Cr governing the lattice solubility but not the enhanced U diffusivity. Instead, Cr/CR 2 O 3 redox chemistry in a well-defined oxygen potential explains the differences in the U diffusivity and O/M ratio. The primary mechanism of doping enhanced grain growth is found to be liquid assisted sintering due to a CRO (1) eutectic phase at the grain boundaries. The role of inhomogeneities in Cr concentration in UO 2 at various length scales across the materials microstructure is highlighted and connected to promising experimental and modeling work to fill in the gaps in the current understanding of Cr-doped UO 2 . The review considers both the open scientific questions and engineering applications to illustrate the deep connections between the practice and theory in the design of accident tolerant nuclear fuels. In conclusion, the review ends with an outline of future works that combine meticulous irradiation studies and high resolution experiments with next generation modeling and simulations techniques empowered by machine learning advances to accelerate the fabrication and adoption of Cr-doped UO 2 light water reactors.

Cleveland, Mack Wesley [Massachusetts Inst. of Tec↗
DOE OSTI2025

Morphological Characterization of Uranyl Fluoride Particles via Atomic Force Microscopy

Uranium hexafluoride (UF 6 ) undergoes a rapid hydrolysis reaction when exposed to atmospheric water. In addition to producing hazardous HF gas, the hydrolysis reaction produces uranyl fluoride (UO 2 F 2 ), a radioactive solid phase particulate material. Because of the technological utility of UF 6 in the nuclear fuel cycle, understanding the transport properties of UO 2 F 2 aerosol produced via UF 6 hydrolysis is important for accident scenarios. Moreover, the fundamental chemical and physical properties of the UF 6 hydrolysis reaction are not completely understood. Recently, several experiments on the aerosol phase properties of UO 2 F 2 produced in this way have shown that under most relevant conditions, the particle size distribution (PSD) of UO 2 F 2 can be extremely small, approximately 3 to 5 nm, which is well below the threshold that can be routinely observed via scanning electron microscopy (SEM). Although readily observable in the aerosol phase, observation of nanometer-sized particles in the condensed phase (i.e. deposited on surfaces) remains a challenge. Here, in this study, we have used atomic force microscopy (AFM) to study the PSD and morphological characteristics of UO 2 F 2 deposited at low and high concentrations under different humidity conditions, a primary variable in the hydrolysis reaction. Here, we find strong agreement between PSD measured in the aerosol phase via scanning mobility particle sizing and PSD measured via AFM, with particle sizes peaked below 4 nm for low-humidity conditions. At higher humidity, the distribution is centered around 5 to 10 nm but extends up to 20 nm. These results are in stark contrast to previous measurements using SEM that show PSD on the order of 300- to 1000-nm particle sizes; moreover, these are the first direct measurements of individual particles of UO 2 F 2 having been produced via UF 6 hydrolysis deposited on surfaces. These measurements, therefore, open a new avenue for collecting and detecting UO 2 F 2 in the condensed phase and further refine the PSD, which is critical for environmental transport determinations.

Uranium hexafluoride↗
DOE OSTI2025

Resonant x-ray emission across the L 3 edge of uranium compounds

A narrow bandwidth x-ray beamline and a multi-crystal von Hamos spectrometer were used to record x-ray absorption and x-ray emission (XES) across the uranium L 3 edge of UO 2 , UO 3 , Cs 2 UO 2 Cl 4 , and Cs 2 UCl 6 . Measurements were made over 17150–17250 eV with an instrumental resolution of ∼2 eV. This resolution allowed the use of Lorentzian peak fits to the L 3 N 4 and L 3 N 5 characteristic x-ray fluorescence lines that have ∼12–13 eV lifetime widths. The fluorescence yields of the four compounds display strong white lines near threshold and multiple scattering features at higher energies. The XES spectra were fit with three Lorentzians, two for the L 3 N 4 and L 3 N 5 lines and one for inelastic scattering by 2p–6d excitations and 4d–6d final states. The intensities of the white lines were largely due to the inelastic scattering component. To support the measurements, relativistic equation-of-motion coupled-cluster and restricted active space configuration interaction calculations were performed for uranium core-excitation energies in Cs 2 UO 2 Cl 4 and Cs 2 UCl 6 . These calculations with rigorous treatments of relativistic effects are shown to provide accurate uranium L 3 -edge binding energies, L 3 N 5 emission energies, as well as the energy losses in the inelastic scattering process. The measured and calculated results show variations between compounds with U(IV) oxidation states that contain 6d 0 5f 2 electrons in their ground configurations (UO 2 and Cs 2 UCl 6 ) compared with U(VI) compounds (UO 3 and Cs 2 UO 2 Cl 4 ) with empty 5f and 6d configurations.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

Computational and Experimental Investigation of Thermal-Mechanical- Chemical Mechanisms of High-burnup Spent Nuclear Fuel (SNF) Processes at Elevated Temperatures and Degradation Behavior in Geologic Repositories

The overarching goal of the combined computational and experimental R&D activities proposed in this project is to enhance understanding of the mechanisms and thermal-mechanical-chemical (TMC) parameters controlling the instant release fraction (IRF) and matrix dissolution of high-burnup (HB; burnup) spent nuclear fuels (SNFs) and the subsequent formation, stability, and phase transformations of SNF alteration products under long-term storage and geological disposal conditions. Uranium dioxide may undergo oxidative corrosion/alteration, and the IRF may be increased for HB SNF, both of which may affect environmental systems associated with SNF long-term storage and disposal. The oxidative matrix dissolution may form various complex uranyl-based phases, including a rich variety of oxides, silicates, carbonates and other secondary minerals in varied geological environments (e.g., studtite, metastudtite, amorphous uranyl peroxide, uranium trioxide, triuranium octoxide, schoepite, dehydrated schoepite, metaschoepite, becquerelite, soddyite, rutherfordine,...). These uranyl phases generally have higher mobility UO 2 +2 species than less soluble U 4+ phases. However, limited information on the thermodynamic properties and formation kinetics of these uranyl-bearing phases is available to predict explicitly paragenesis under the conditions relevant to long-term storage or disposal. The proposed project draws on complementary expertise and research backgrounds from the team members: (i) to apply a combined ab initio modeling (UNLV/UTEP and SNL) and experimental (UNLV) strategy investigating the high-temperature TMC mechanisms of alteration of SNF under α-radiolysis conditions; (ii) to investigate the mechanistic of phase transformations in UNF degradation products under various conditions expected in long-term storage systems (e.g. (UO 2 )O 2 (H 2 O) 4 → (UO 2 )O 2 (H 2 O) 2 → U 2 O 7 → UO 3 → U 3 O 8 ); (iii) to determine high-accuracy TMC parameters for complex uranyl-based phases formed in storage or geological disposal environments (e.g. UO 3 (H 2 O) 2 , Ca[(UO 2 ) 6 O 4 (OH) 8 ] 8 H 2 O, (UO 2 ) 2 (SiO 4 ) 3 2H 2 O,…). The unforeseen COVID-19 pandemic led to the laboratory/campus closure since March 2020, that resulted in a significant delay in reaching milestones in a satisfactory manner, due to (i) the statewide recommendation from stop-working to later limited work in the lab and work-from-home (WFH), (ii) no in-person interactions, and (iii) a hiring freeze at UNLV. Therefore, a no cost extension (10/01/2021- 9/30/2022) was requested to help make up the time we lost during the global pandemic in 2020-2021, leading to paradigm shifts in the focus of the project in the following three main tasks: Task 1 (Computational), Task 2 (Experimental), and Task 3 (Final report, due on 12/29/2022).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Comparative analysis of temperature dependent properties of commercial nuclear fuel pellet and surrogates undergoing cracking: A review

A variety of normal and accident scenarios can generate thermal stresses enough to cause cracking in light water reactor (LWR) fuel. To better understand this behavior, cracking experiments have been carried out to induce thermal gradients in fuel pellets via induction heating and direct resistance heating. In this study, Ceria (CeO 2 ) and yttria stabilized zirconia (YSZ) pellets were chosen as a surrogate fuel material for uranium dioxide (UO 2 ). Induction heating was done using copper coils and molybdenum susceptors which heated the surrogates to a threshold temperature that is sufficiently high for the fuel material to conduct current. Thereafter, direct resistance heating was achieved by passing current through the specimen using a DC power supply to introduce volumetric heating to replicate reactor operating conditions. Simultaneous real-time dual imaging of the ceria pellet surface has been designed using optical and infra-red camera system to capture images of cracks and full-field temperature gradients on pellet. It was observed that YSZ pellets need a much higher voltage-current for volumetric heating and do not exhibit the cracking pattern as ceria and UO 2 , hence YSZ was ruled out for further consideration. Ceria was found to be an appropriate surrogate for UO 2 . Furthermore, the experimental set up and test conditions demand the need to primarily understand the thermo-physical, mechanical and optical properties of UO 2 and the surrogates. Thus, it is essential to have an in-depth knowledge about the various temperature dependent properties of UO 2 and CeO 2 for establishing a comparative analysis between the surrogate and UO 2 for conducting experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-gradient magnetic separation of colloidal uranium oxide particles from soil components in aqueous suspensions

The separation of uranium oxide (UO 2 ) particles from soil-surrogate particles in aqueous suspensions was achieved using filtration enhanced by a magnetic field. Enhanced attraction of paramagnetic UO 2 colloids to a ferromagnetic stainless-steel filter placed in a strong magnetic field arises because of the positive magnetic susceptibility of the particles and the high-gradient field generated near ferromagnetic fibers. Enhanced uptake of smaller particles over larger ones occurs through Brownian motion that promotes the collision of particles with the ferromagnetic fibers of the filter. Hence, this work focused on UO 2 particles in the colloidal size range. Experiments used a water-cooled electromagnet and an array of permanent magnets. Chemical analysis showed that the magnetic field increased the capture efficiency of uranium particles from a range of 27–53% with the magnet off up to 98% with the magnet on after a single pass of the suspension through the filter. Further, the recovery of the UO 2 particles from the filter, however, was more difficult to achieve. Small amounts of UO 2 , together with significant amounts of background SiO 2 particles, were removed from the filter during a first flush with the magnetic field on. A much larger recovery of UO 2 was not observed until a second out-of-field flush was performed, which also released some SiO 2 . The degree to which particle separation was enhanced through the use of multi-stage filtration compared to single pass-through filtration was also examined. A design was suggested that could be used to optimize the separation efficiency for a continuous process.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

Performance of U 3 Si 2 in an LWR following a cladding breach during normal operation

High-density fuels have been proposed as a possible replacement for uranium-dioxide as a fuel for light water reactors (LWRs) due to their increased loading of fissionable material. The objectives of this proposal are (1) to increase reactor cycle length and reactor power, and (2) to offset any neutronic penalty associated with advanced cladding systems. Of the high-density fuels under consideration, there is particular interest in triuranium disilicide (U 3 Si 2 ) due to its increased metal density and favorable thermal properties as compared to UO 2 . However, there are concerns regarding the chemical compatibility of U 3 Si 2 with water and steam as used for LWR coolant.This paper summarizes research on fuel-coolant chemical compatibility for UO 2 LWR fuel during a cladding breach and highlights that generally, because of its chemical inertness, UO 2 -coolant reactions are of little consequence to reactor operation. However, the volumetric expansion associated with the reaction of UO 2 and oxygen is a concern for possible conditions encountered during air ingress of dry storage. These same concerns arise for U 3 Si 2 , which exhibits greater volumetric expansion than UO 2 when exposed to water or steam. These reactions ultimately result in increased fuel volume that the cladding must accommodate, as well as additional heat generated as the fuel reacts.The BISON fuel performance code was used to perform a comparative analysis on the behavior of UO 2 and U 3 Si 2 under normal operation. Silicide fuel simulations were then extended to demonstrate how varying thermodynamic and chemical kinetics influence fuel expansion and subsequent cladding performance during a cladding breach. These simulations were further extended to a 3D subsection of a fuel rod to demonstrate the characteristics of the resulting cladding crack.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Atomistic and cluster dynamics modeling of fission gas (Xe) diffusivity in TRISO fuel kernels

TRISO fuel particles are candidates for use in next generation reactors including gas reactors, fluoride salt-cooled high temperature reactors, and micro-reactors. The UCO fuel kernel consists of a uranium dioxide (UO) and uranium carbide mixture. The addition of UC helps suppress the formation of carbon monoxide gas, which led to failures during initial TRISO development. The addition of uranium carbide alters the chemistry of the UO kernel, which is known to influence performance parameters such as fission gas diffusivity, although the impact has not been quantified and no models exist that take the change in chemistry into account. Therefore, better understanding and more accurate models of the impact of chemistry on fuel performance are of high priority. In this paper, a first-principles density functional theory (DFT) and empirical potential based multi-scale study has been carried out to model the diffusivity of fission gas xenon (Xe) in UCO TRISO fuel kernels. The focus is on the UO component in the UCO fuel kernels, as that represents the largest volume fraction of the fuel kernels. The study relies on DFT and empirical potential calculations to determine Xe and point defect properties, which are then used in thermodynamic and kinetic models to predict diffusion for intrinsic conditions. In addition, the information is utilized in cluster dynamics simulations using the Centipede code to estimate the impact of irradiation on defect transport. Additionally, the presence of UC or UC in the UCO fuel kernels is shown to have a substantial impact on the UO non-stoichiometry by inducing oxygen vacancies and driving UO sub-stoichiometric, which causes much slower Xe diffusion in UCO compared to light water reactor UO fuel. The application of this model in fuel performance simulations using the Bison code is also demonstrated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Energetics of oxidation and formation of uranium mononitride

Uranium mononitride (UN) is an advanced nuclear fuel currently being considered for use in several generation IV fast and thermal neutron spectrum core designs, with additional applications to thermal and electric nuclear propulsion reactors. Here, to better understand the thermal behavior and thermodynamic stability of UN, we investigated the bulk thermal oxidation process and thermochemical reactions, including the enthalpy of oxidation and standard enthalpy of formation, by conducting thermalgravimetric analysis – differential scanning calorimetry coupled with mass spectrometry (TGA-DSC-MS), and high temperature transposed temperature drop and oxide melt drop solution calorimetry. The bulk oxidation of UN (containing a small amount of α-UN 1.5+x ) in air was found to follow a step-wise process characterized by consecutive oxidative reactions UN-UN 1.5+x -UO 2 → UO 2 -UO 3 —N k → UO 3 —N k → UO 3 → U 3 O 8 . TGA results support that the UO 2 – U 2 N 3+x passivating layer delays the onset of rapid bulk oxidation of UN in air up to 662 K. Synchrotron X-ray diffraction (XRD) and extended X-ray absorption fine structure (EXAFS) analyses were performed to characterize UN and its final oxidized product. The standard enthalpy of formation (ΔH° f ) of UN was determined to be –144.4 ± 5.9 kJ/mol·atom, in good agreement with previously determined values from Pt encapsulation and bomb calorimetric experiments. Lastly, a negative linear correlation between ΔH° f and the N/U molar ratio was established based on the thermochemical data obtained in this work and previously reported enthalpies of formations of β-UN 1.5-x and α-UN 1.5+x .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Influence of uranyl complexation on the reaction kinetics of the dodecane radical cation with used nuclear fuel extraction ligands (TBP, DEHBA, and DEHiBA)

Specialized extractant ligands – such as tri-butyl phosphate (TBP), N,N-di-(2-ethylhexyl)butyramide (DEHBA), and N,N-di-2-ethylhexylisobutryamide (DEHiBA) – have been developed for the recovery of uranium from used nuclear fuel by reprocessing solvent extraction technologies. These ligands must function in the presence of an intense multi-component radiation field, and thus it is critical that their radiolytic behaviour be thoroughly evaluated. This is especially true for their metal complexes, where there is negligible information on the influence of complexation on radiolytic reactivity, despite the prevalence of metal complexes in used nuclear fuel reprocessing solvent systems. Here we present a kinetic investigation into the effect of uranyl (UO 2 2+ ) complexation on the reaction kinetics of the dodecane radical cation (RH˙ + ) with TBP, DEHBA, and DEHiBA. Complexation had negligible effect on the reaction of RH˙ + with TBP, for which a second-order rate coefficient (k) of (1.3 ± 0.1) × 10 10 M -1 s -1 was measured. For DEHBA and DEHiBA, UO 2 2+ complexation afforded an increase in their respective rate coefficients: k(RH˙ + + [UO 2 (NO 3 ) 2 (DEHBA) 2 ]) = (2.5 ± 0.1) × 10 10 M -1 s -1 and k(RH˙ + + [UO 2 (NO 3 ) 2 (DEHiBA) 2 ]) = (1.6 ± 0.1) × 10 10 M -1 s -1 . This enhancement with complexation is indicative of an alternative RH˙ + reaction pathway, which is more readily accessible for [UO 2 (NO 3 ) 2 (DEHBA) 2 ] as it exhibited a much larger kinetic enhancement than [UO 2 (NO 3 ) 2 (DEHiBA) 2 ], 2.6× vs. 1.4×, respectively. Complementary quantum mechanical calculations suggests that the difference in reaction kinetic enhancement between TBP and DEHBA/DEHiBA is attributed to a combination of reaction pathway (electron/hole transfer vs. proton transfer) energetics and electron density distribution, wherein attendant nitrate counter anions effectively ‘shield’ TBP from RH˙ + electron transfer processes.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Uranyl uptake into metal–organic frameworks: a detailed X-ray structural analysis

Metal–organic frameworks (MOF) are a subclass of porous framework materials that have been used for a wide variety of applications in sensing, catalysis, and remediation. Among these myriad applications is their remarkable ability to capture substances in a variety of environments ranging from benign to extreme. Among the most common and problematic substances found throughout the world's oceans and water supplies is [UO 2 ] 2+ , a common mobile ion of uranium, which is found both naturally and as a result of anthropogenic activities, leading to problematic environmental contamination. While some MOFs possess high capability for the uptake of [UO 2 ] 2+ , many more of the thousands of MOFs and their modifications that have been produced over the years have yet to be studied for their ability to uptake [UO 2 ] 2+ . However, studying the thousands of MOFs and their modifications presents an incredibly difficult task. As such, a way to narrow down the numbers seems imperative. In this work, we evaluate the binding behaviors as well as identify the specific binding sites of [UO 2 ] 2+ incorporated into six different Zr MOFs to elucidate specific features that improve [UO 2 ] 2+ uptake. In doing so, we also present a method for the determination and verification of these binding sites by Anomalous wide-angle X-ray scattering, X-ray fluorescence, and X-ray absorption spectroscopy. This research not only presents a way for future research into the uptake of [UO 2 ] 2+ into MOFs to be conducted but also a means to evaluate MOFs more generally for the uptake of other compounds to be applied for environmental remediation and improvement of ecosystems globally.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Suppressed thermal conductivity in hyperstoichiometric uranium dioxide controlled by phonon lifetimes

Thermal transport in nuclear fuels used for nuclear energy applications is directly tied to performance and reliability. Uranium dioxide (UO 2 ), one of the most important nuclear fuels, can accumulate excess oxygen atoms as interstitial defects, which significantly impacts thermal transport properties. In this study, thermal conductivities and inelastic neutron scattering (INS) measurements on UO 2+ x were performed at low temperatures (2–300K). The thermal conductivity of UO 2+ x (x = 0, 0.03, 0.04, and 0.11) is significantly suppressed compared to UO 2 except near the Néel temperature T N = 30.8 K, where it is independent of x. INS measurements demonstrate that the heat capacities and phonon group velocities of UO 2 and UO 2.08 are similar, and the suppressed thermal conductivity results from smaller phonon lifetimes. These perceptions advance our understanding of thermal transport properties in advanced nuclear fuels and guide safe and economic utilization of nuclear energy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Experimental study of the influence of gas puff locations on H-mode boundary plasmas with argon seeding on EAST

To investigate the optimal scenario of impurity seeding to obtain divertor plasma detachment for target protection, experiments with Ar&D 2 seeding from two different poloidal locations, the upper outer (UO) divertor target and lower outer (LO) target, were carried out on EAST. Partial energy detachment (the electron temperature near the strike point T e,spt ≤ 10 eV) were obtained with Ar&D 2 mixture puffing from the UO target and, for the first time, from the LO target into H-mode plasmas in the upper single null (USN) configuration. The peak heat flux q t on the UO target was significantly reduced (by ~80%). The rollover of ion flux density j s did not appear probably due to insufficient momentum loss, which is independent of the puff locations. The poloidal asymmetries of particle and heat fluxes on the targets have also been investigated. The UO-dominant asymmetry of particle flux was reversed, while the UO-dominant asymmetry of heat flux was mitigated but not reversed. The plasma confinement dropped by only 14% and 8.2% in the LO-puff case and UO-puff case, respectively, during detachment. The high level of C may contributed greatly to the higher radiation in the bulk plasma region and the greater decline in W MHD in the LO-puff case.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Demonstration of Electroreduction Technology to Convert GNF Uranium Oxide Powder to Metal

Global Nuclear Fuel – Americas LLC (GNF) has partnered with Argonne National Laboratory to demonstrate electroreduction of uranium oxides produced by deconversion of UF 6 to uranium metal through the Gateway for Accelerated Innovation in Nuclear (GAIN) program under the U.S. Department of Energy to accelerate the domestic production of metallic advanced reactor fuels. Electroreduction of uranium oxide was first demonstrated and patented by Argonne in the early 2000s as a technology to convert used oxide nuclear fuel from light water reactors to metal for further fuel reprocessing. More recently, electroreduction has been proposed as a front-end technology for metallization of uranium oxides produced by deconversion of UF 6 and for scrap recovery of oxide materials. During the electroreduction process, UO 2 powder is contained in a stainless-steel mesh basket with a cathode lead located in the center of the UO 2 bed. The basket is immersed in lithium chloride molten salt electrolyte containing 1 wt% lithium oxide along with a platinum anode and a nickel/nickel oxide (Ni/NiO) reference electrode. Current is applied to the cell between the cathode and anode to reduce the UO 2 to metallic uranium via a solid-state reduction reaction. Oxide ions released from the UO 2 during reduction are transported through the salt to the anode where oxygen gas is evolved. Once reduction is complete, the basket containing the metallicized uranium is removed from the salt and can be processed to remove the salt and consolidate the uranium into an ingot for use in metallic fuel fabrication. This project was performed to provide evidence of the electroreduction technology readiness level for metallization of UO 2 powder, identify and retire technical risks for industrialization of electroreduction, and accelerate the path to commercialization for metallic fast reactor fuel production. To that end, five electroreduction tests were performed with UO 2 provided by GNF and the resulting product was analyzed for the extent of conversion to metal and for impurity contents of the metal product to verify that electroreduction does not introduce impurities that would prevent use of the product in metallic fuel fabrication.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Induced Ferromagnetism in Epitaxial Uranium Dioxide Thin Films

Abstract Actinide materials have various applications that range from nuclear energy to quantum computing. Most current efforts have focused on bulk actinide materials. Tuning functional properties by using strain engineering in epitaxial thin films is largely lacking. Using uranium dioxide (UO 2 ) as a model system, in this work, the authors explore strain engineering in actinide epitaxial thin films and investigate the origin of induced ferromagnetism in an antiferromagnet UO 2 . It is found that UO 2+ x thin films are hypostoichiometric ( x <0) with in‐plane tensile strain, while they are hyperstoichiometric ( x >0) with in‐plane compressive strain. Different from strain engineering in non‐actinide oxide thin films, the epitaxial strain in UO 2 is accommodated by point defects such as vacancies and interstitials due to the low formation energy. Both epitaxial strain and strain relaxation induced point defects such as oxygen/uranium vacancies and oxygen/uranium interstitials can distort magnetic structure and result in magnetic moments. This work reveals the correlation among strain, point defects and ferromagnetism in strain engineered UO 2+ x thin films and the results offer new opportunities to understand the influence of coupled order parameters on the emergent properties of many other actinide thin films.

36 MATERIALS SCIENCE↗