Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transmission Electron Microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Electron petrography of Apollo 14 and 15 breccias and shock-produced analogs

Six lunar breccias were studied in detail by optical and transmission electron microscopy and separated into two classes on the basis of presence or absence of recovery and recrystallization textures: Class A breccias with no recrystallization include samples 14063, 14301, and 15498; Class B breccias with recrystallization include samples 14321, 15455, and 15418. Samples of Apollo 16 soil (65010) experimentally shocked to 50, 100, and 250 kilobars pressure were sectioned and studied for comparison with the breccias. It is concluded that the Class A breccias were formed from unconsolidated lunar regolith by deformation due to shock waves of a few tens of kilobars. The Class B breccias could also have been produced from unconsolidated material at higher shock stresses, the annealing being achieved by the heating resulting from the shock deformation.

Christie, J. M.↗
NASA NTRS1974

The resistance to embrittlement by a hydrogen environment of selected high strength iron-manganese base alloys

Fe-16Mn and Fe-25Mn base alloys, which had been cold worked to yield strength levels of 201 and 178 KSI, were resistant to degradation of mechanical properties in a one atmosphere hydrogen environment at ambient temperature under the loading conditions employed in this investigation. Transmission electron microscopy established that bands of epsilon phase martensite and fcc mechanical twins were formed throughout the fcc matrix when these alloys were cold worked. In the cold worked alloys a high density of crystal defects were observed associated with both types of strain induced structures, which should contribute significantly to the strengthening of these alloys. High strength iron base alloys can be produced which appear to have some resistance to degradation of mechanical properties in a hydrogen environment under certain conditions.

Benson, R. B., Jr.↗
NASA NTRS1974

Surface recrystallization theory of the wear of copper in liquid methane

Copper was subjected to sliding against 440C in liquid methane. The normal load range was from 1/4 to 2 kilograms, and the sliding velocity range was from 3.1 to 25 meters per second. Over this range of experimental parameters, the wear rate of the copper rider was found to be proportional to the sliding velocity squared and to the normal load. Transmission electron microscopy was used to study the dislocation structure in the copper very near the wear scar surface. It was found that near the wear scar surface, the microstructure was characterized by a fine-cell recrystallized zone in which individual dislocations could be distinguished in the cell walls. The interiors of the cells, about 0.5 micrometer in diameter, were nearly dislocation free. Below the recrystallized layer was a zone that was intensely cold worked by the friction process. With increasing depth, this intensely cold worked zone gradually became indistinguishable from the partially cold worked bulk of the copper, representative of the initial condition of the material.

Bill, R. C.↗
NASA NTRS1975

Direct observation of small cluster mobility and ripening

Direct evidence is reported for the simultaneous occurrence of Ostwald ripening and short-distance cluster mobility during annealing of discontinuous metal films on clean amorphous substrates. The annealing characteristics of very thin particulate deposits of silver on amorphized clean surfaces of single crystalline thin graphite substrates were studied by in-situ transmission electron microscopy (TEM) under controlled environmental conditions (residual gas pressure of 10 to the minus 9th power torr) in the temperature range from 25 to 450 C. Sputter cleaning of the substrate surface, metal deposition, and annealing were monitored by TEM observation. Pseudostereographic presentation of micrographs in different annealing stages, the observation of the annealing behavior at cast shadow edges, and measurements with an electronic image analyzing system were employed to aid the visual perception and the analysis of changes in deposit structure recorded during annealing. Slow Ostwald ripening was found to occur in the entire temperature range, but the overriding surface transport mechanism was short-distance cluster mobility.

Heinemann, K.↗
NASA NTRS1975

Structure-property relationships in thermomechanically treated beryllia dispersed nickel alloys

BeO dispersed nickel alloys, produced by powder metallurgy techniques, were studied extensively in stress rupture at 815, 982, and 1093 C (1088, 1255, and 1366 K) and by transmission electron microscopy. The alloys were subjected to a variety of thermomechanical treatments (TMT) to determine the benefits of TMT on properties. It is shown that the use of intermediate annealing treatments after 10 pct reduction steps is highly beneficial on both low and high temperature properties. It is indicated that the high temperature strength is not primarily dependent on the grain aspect ratio or texture but depends strongly on the dislocation density and distribution of dislocations in a stable substructure which is pinned by the fine oxide dispersion.

Grewal, M. S.↗
NASA NTRS1974

Solar wind and micrometeorite alteration of the lunar regolith

Developments in the understanding of reduction processes which occur in the lunar regolith as a result of solar-wind bombardment and micrometeorite impacts are discussed. The mechanism is described by which water released during reduction is removed from the lunar surface, and the possible contribution of solar-wind sputtering to the reduction process is considered. It is shown that the overall reduction efficiency of incoming hydrogen ions may reach several per cent, which is sufficient to produce all the metallic iron observed in the regolith. Mossbauer spectroscopic data on the amount of metallic iron present as isolated atoms or small clusters in reduced grain surfaces are presented together with data on the metallic iron content of fines samples obtained by Mossbauer spectroscopy, ferromagnetic resonance, and scanning as well as transmission electron microscopy. A portable magnetic probe is described which has been designed for determining surface-exposure age profiles in intact lunar core and drive-tube samples.

Housley, R. M.↗
NASA NTRS1975

Precipitation of silicon from splat-cooled Al-Si alloys

Splat cooled Al-Si solid solutions with 1 to 11 at.% Si were prepared and their precipitation kinetics were studied by transmission electron microscopy. The time required for appearance of particles visible at a magnification of 35,000 times was determined at temperatures between 248 K and 573 K. The resulting Arrhenius plots yielded activation energies ranging from 55 to 40 plus or minus 2kJ/mol over the composition range. Precipitate densities were higher and denuded zones of 100 to 150 nm were narrower than in comparable solid quenched samples. The activation energies are explained in terms of excess point defect concentrations.

Matyja, H.↗
NASA NTRS1976

Rolling-contact deformation of MgO single crystals

Magnesium oxide single crystals were used as a model bearing material and deformed by rolling contact with a steel ball 0.64 cm in diameter. A dependence of depth of slip on rolling velocity which persisted with increasing numbers of rolling-contact cycles was discovered. The track width, track hardness and dislocation interactions as observed by transmission electron microscopy all increased in a consistent manner with increasing cycles. The rolling-contact state of stress produces a high density of dislocations in a localized zone. Dislocation interaction in this zone produces cleavage-type cracks after a large number of rolling-contact cycles. The orientation of the crystal influences the character of dislocation accumulation.

Dufrane, K. F.↗
NASA NTRS1976

The influence of growth rate and temperature on high cycle fatigue of Al-Al3Ni

High-cycle fatigue tests have been conducted on specimens of an Al-Al3Ni eutectic alloy, unidirectionally solidified at selected rates from 0.000139 to 0.3 cm/sec. Tests were conducted in air at 298, 458 and 683 K. Room temperature fatigue lives were independent of growth rate at low solidification rates but were markedly improved in samples grown at 0.3 cm/sec. Materials grown at 0.00833 cm/sec exhibited fatigue lives similar to those of the lower growth rates, despite gross misalignment due to cellular growth. The dependence of fatigue life on growth rate at elevated temperatures appears to be due primarily to differences in cyclic creep rates as a result of varying interfiber spacings. Crack initiation and propagation mechanisms were established by metallographic and fractographic examination. Dislocation substructure-fiber interactions were studied by transmission electron microscopy.

Maurer, G. E.↗
NASA NTRS1976

Direct observation of small cluster mobility and ripening

Direct evidence is reported for the simultaneous occurrence of Ostwald ripening and short-distance cluster mobility during annealing of discontinuous metal films on clean amorphous substrates. The annealing characteristics of very thin particulate deposits of silver on amorphized clean surfaces of single-crystalline thin graphite substrates have been studied by in situ transmission electron microscopy (TEM) under controlled environmental conditions in the temperature range from 25 to 450 C. It was possible to monitor all stages of the experiments by TEM observation of the same specimen area. Slow Ostwald ripening was found to occur over the entire temperature range, but the overriding surface transport mechanism was short-distance cluster mobility. This was concluded from in situ observations of individual particles during annealing and from measurements of cluster size distributions, cluster number densities, area coverages, and mean cluster diameters.

Heinemann, K.↗
NASA NTRS1976

In situ investigation of the mobility of small gold clusters on cleaved MgO surfaces

The mobility of small clusters of gold (about 10 A in diameter) on electron-beam-cleaved MgO surfaces was studied by in situ transmission electron microscopy under controlled vacuum and temperature conditions. During the first 10 min following a deposition at room temperature, over 10 per cent of the crystallites moved over short distances (about 20 A) discontinuously, with a velocity greater than 150 A/sec. Eighty per cent of the mobility events were characterized by the avoidance of proximity of other crystallites, and this was tentatively explained as the result of repulsive elastic forces between the interacting crystallites.

Metois, J. J.↗
NASA NTRS1976

Microscopic aspects of interfacial reactions in diffusion bonding processes

Microscopic aspects of interfacial reactions are discussed, such as interdiffusion, formation of intermetallic phases, generation and annihilation of lattice defects, effect of temperature, grain size, etc., which normally occur in diffusion bonding processes. Relationships between properties and microstructure in thin film couples are examined utilizing a unique combination of contact resistance measurements and characterization by transmission electron microscopy.

Shearer, M. P.↗
NASA NTRS1976

76535 - Thermal history deduced from pyroxene precipitation in anorthite

Plagioclase in the slowly cooled lunar troctolite 76535 contains abundant rows of inclusions shown by transmission electron microscopy, electron diffraction, and X-ray energy analysis to consist mainly of augite, pigeonite, orthopyroxene, pores, and an unidentified phase which is preferentially thinned out during sample preparation. A minor inclusion is Ni-Fe metal. The pyroxenes are interpreted to have exsolved from plagioclase in the solid state.

Nord, G. L., Jr.↗
NASA NTRS1977

Calorimetric studies of 7000 series aluminum alloys. I - Matrix precipitate characterization of 7075. II - Comparison of 7075, 7050, and RX720 alloys

Correlation between differential scanning calorimetry and high temperature transmission electron microscopy for the characterization of preexisting matrix precipitates in the highest-strength and overaged tempers of 7075 aluminum was demonstrated. The solid state reactions undergone by these tempers in the 20-500 C temperature range were elucidated and expressed in terms of thermodynamic and kinetic parameters. The dissolution parameters for each phase are distinguishable and serve as guidelines for a rapid characterization of the matrix microstructure of these alloys.

Deiasi, R.↗
NASA NTRS1978

Microstructure and mechanical properties of quenched and tempered 300M steel

Type 300M steel, which is being used for the landing gear on the space shuttle orbiter, was subjected to a wide range of quenched and tempered heat treatments. The plane-strain fracture toughness and the tensile ultimate and yield strengths were evaluated. Cryogenic mechanical properties were obtained for conventionally heat-treated steel. The microstructure of all heat-treated test coupons was studied both optically and by transmission electron microscopy. Fracture surfaces were studied by means of scanning electron microscopy. Results indicate that substantial improvement in toughness with no loss in strength can be accomplished in quenched and tempered steel by austenitizing at 1255 K or higher. Low fracture toughness in conventionally austenitized 300M steel (1144 K) appears to be caused by undissolved precipitates, seen both in the submicrostructure and on the fracture surface, which promote failure by quasi-cleavage. The precipitates appeared to dissolve in the range 1200 to 1255 K.

Youngblood, J. L.↗
NASA NTRS1977

Microstructure of hot-pressed Al2O3-Si3N4 mixtures as a function of holding temperature

Powder mixtures of 40 m/o Si3N4-60 m/o Al2O3 were hot-pressed at 4000 psi at various holding temperatures from 1100 C to 1700 C. Scanning and transmission electron microscopy results were correlated to X-ray phase analysis and density measurements. The progressively developed microstructure was used to interpret the densification behavior of SiAlON.

Yeh, H. C.↗
NASA NTRS1977

In situ oxidation studies on /001/ copper-nickel alloy thin films

High-resolution transmission electron microscopy studies are reported of (001)-oriented single crystalline thin films of Cu-3%Ni, Cu-4.6%Ni, and Cu-50%Ni alloy which were prepared by vapor deposition onto (001) NaCl substrates and subsequently annealed at around 1100 K and oxidized at 725 K at low oxygen partial pressure. At all alloy concentrations, Cu2O and NiO nucleated and grew independently without the formation of mixed oxides. The shape and growth rates of Cu2O nuclei were similar to rates found earlier. For low-nickel alloy concentrations, the NiO nuclei were larger and the number density of NiO was less than that of Cu-50%Ni films for which the shape and growth rates of NiO were identical to those for pure nickel films. Phenomena involving a reduced induction period, surface precipitation, and through-thickness growth are also described. The results are consistent with previously established oxidation mechanisms for pure copper and pure nickel films.

Heinemann, K.↗
NASA NTRS1978

TEM observations on grain boundaries in sintered silicon, part 1

Grain boundaries in silicon with a predetermined orientation were prepared by the sintering of two single crystals. A combination of standard transmission electron microscopy and lattice imaging was used to investigate the structure of the boundaries produced. Low angle grain boundaries on (100) and (111) planes, and twin boundaries on (111) planes are discussed in detail.

Ast, D. G.↗