Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Spatially dispersing Yu-Shiba-Rusinov states in the unconventional superconductor FeTe 0.55 Se 0.45

By using scanning tunneling microscopy (STM) we find and characterize dispersive, energy-symmetric in-gap states in the iron-based superconductor FeTe 0.55 Se 0.45 , a material that exhibits signatures of topological superconductivity, and Majorana bound states at vortex cores or at impurity locations. We use a superconducting STM tip for enhanced energy resolution, which enables us to show that impurity states can be tuned through the Fermi level with varying tip-sample distance. We find that the impurity state is of the Yu-Shiba-Rusinov (YSR) type, and argue that the energy shift is caused by the low superfluid density in FeTe 0.55 Se 0.45 , which allows the electric field of the tip to slightly penetrate the sample. We model the newly introduced tip-gating scenario within the single-impurity Anderson model and find good agreement to the experimental data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Validity of Machine Learning in the Quantitative Analysis of Complex Scanning Near-Field Optical Microscopy Signals Using Simulated Data

Scattering-type scanning near-field optical microscope (s-SNOM) is a modern technique for subdiffractional optical imaging and spectroscopy. Over the past two decades, tremendous efforts have been devoted to modeling complex tip-sample interactions in s-SNOM, aimed at understanding the electrodynamics of materials at the nanoscale. However, due to complexities in analytical methods and the limited computation power for fully numerical simulations, compromises must be made to facilitate the modeling of tip-sample interaction, such as using quasistatic approximation or unrealistic tip geometries. Here, we apply a variety of widely utilized machine-learning methods, including k nearest neighbor and feedforward neural network etc. to study the phase-resolved spectroscopic near-field response. With only a small set of training data, which is simulated using the finite-dipole model, we demonstrate that the relation between the experimental near-field signal and sample optical constant can be one to one mapped without the need for tip modeling: for a given material with a moderate dielectric function, its complex near-field spectrum can be accurately determined within the mid-IR spectral range, and vice versa. Our preliminary study sets the stage for future exploration using real experimental data. Our method is beneficial for processing the increasing amount of data accumulated across many research groups and especially useful for user facilities such as synchrotron-based national laboratories where a large amount of data is generated on a daily basis.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Inelastic relaxation processes in amorphous sodium silicates

During fracture amorphous oxides exhibit irreversible processes, including inelastic and nonrecoverable relaxation effects in the process zone surrounding the crack tip. Here, classical molecular dynamics simulations were used with a reactive forcefield to evaluate inelastic relaxation processes in five amorphous sodium silicate compositions. Overall, the 20% Na 2 O-SiO 2 (NS20) composition exhibited the most inelastic relaxation, followed by the 15% Na 2 O-SiO 2 (NS15) composition, the 25% Na 2 O-SiO 2 (NS25) composition, and finally the 10% (NS10) and 30% (NS30) Na 2 O-SiO 2 compositions. Coordination analysis of the Na + ions identified that during inelastic relaxation the Na+ ions were increasingly coordinated by nonbridging oxygens (NBOs) for the NS10 and NS15 compositions, which was supported by radial analysis of the O-Na-O bond angles surrounding the crack tip. Across the sodium silicate compositional range, two different inelastic relaxation mechanism were identified based on the amount of bridging oxygens (BOs) and NBOs in the Na+ ion coordination shell. At lower (NS10) and higher (NS30) sodium compositions, the entire structured relaxed toward the crack tip. In contrast at intermediate sodium concentrations (NS20) the Na + ion migrates toward the crack tip separately from the network structure. By developing a fundamental understanding of how modified silica systems respond to static stress fields, we will be able to predict how varying amorphous silicate systems exhibit slow crack growth.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Task Information Presentation System

Demonstrate a novel computer-based procedure solution for a multi-unit power plant. TIPS is developed to demonstrate a way to operate a highly automated plant. Currently, there are no plants (nuclear or non-nuclear) that can support this high level of automation. The purpose of TIPS is to help the industries think beyond the current conduct of operations. TIPS is designed to work with the GSE Systems' Combine-cycle gas turbine power plant simulator. TIPS uses the plant data from the simulator to make the user experience of the computer-based procedure more realistic.

Oxstrand, Johanna↗
DOE OSTI2022

Rapid simulations of hyperspectral near-field images of three-dimensional heterogeneous surfaces – part II

The modeling of the near-field interaction in the scattering-type scanning near-field optical microscope (s-SNOM) is rapidly advancing, although an accurate yet versatile modeling framework that can be easily adapted to various complex situations is still lacking. In this work, we propose a time-efficient numerical scheme in the quasi-electrostatic limit to capture the tip-sample interaction in the near field. This method considers an extended tip geometry, which is a significant advantage compared to the previously reported method based on the point-dipole approximation. Using this formalism, we investigate, among others, nontrivial questions such as uniaxial and biaxial anisotropy in the near-field interaction, the relationship between various experimental parameters (e.g. tip radius, tapping amplitude, etc.), and the tip-dependent spatial resolution. The demonstrated method further sheds light on the understanding of the contrast mechanism in s-SNOM imaging and spectroscopy, while also representing a valuable platform for future quantitative analysis of the experimental observations.

Chen, Xinzhong (ORCID:0000000261033848)↗
DOE OSTI2020

Technology Demonstration of a High-Pressure Swirl Oxy-Coal Combustor

This technical report presents the exploration of the design and prototyping of a High-Pressure Swirl Oxy-coal Combustor. Pressurized oxy-coal combustion systems have the potential to improve efficiency along with an increased carbon capture rate. Reduction of flue gas at higher pressure, smaller system size, and capital cost reductions render high-pressure oxy-coal systems particularly attractive as next-generation energy-producing systems. High-pressure oxy-coal combustion systems are a recent concept, and thus operability issues of combustor designs for such systems are not fully understood. Significant challenges exist to maintain oxy-coal combustion stability at elevated pressure and a high CO 2 diluent environment. Although a body of knowledge exists for high-pressure oxygen combustion in rocket engines (or similar applications), it is yet to be strategized how these fundamental concepts can be translated to low-temperature CO 2 diluent combustion regimes. The realization of the pressurized oxy-coal based systems requires combustor components to be designed and demonstrated for an operating pressure over 10 bar. However, pressurized oxy-coal combustor design information at this pressure range and scale relevant to validate those proposed systems is currently limited. Experimental data from MWth scale oxy-coal combustors are needed to identify the optimal trade-off between net efficiency and systems size. The proposed effort is aimed at demonstrating a 1 MWth down-fired swirl Oxy-Coal combustor and investigate the interrelation between combustor operating conditions (pressure; flame stability; flue gas recirculation ratio) and conversion efficiencies to minimize oxygen requirements. One of the key challenges is to configure burner design (i.e., swirl number and injector) and operating conditions for high-pressure oxy-coal combustion systems. These experiments differ from current systems partly due to the high theoretical flame temperature and related burner operability issues associated with oxy-combustion. An ASPEN PLUS® model study for 550 MWe TIPS and ENEL pressurized oxy-coal systems with CO 2 recirculation was performed to evaluate system design, subsystems sizing, and operating condition determination. The system analysis effort included TRL and technology gap determination of subsystems and critical components. This information was scaled to develop design requirements (design pressure and flue gas recirculation: RR Flue Gas = $\frac{m_{flue}}{m_{total}}$) for the 1 MWth combustor. The effects of a wide range of carbon dioxide recirculation ratios on the thermal efficiency of ENEL and TIPS cycles are studied. The pressure of 10 bar and 80 bar are used for ENEL and TIPS cycles, respectively. The thermal efficiency of ENEL is significantly higher than the efficiency of TIPS at a pressure of less than 10 bar. The insights from system analysis were then used to design a 1 MWth swirl oxy-coal combustor. Flame temperature analysis and material strength analysis was performed to determine the combustor thickness. The structural integrity of the combustor was validated by finite element analysis using Abacus® and Hypermesh®. Feasibility of igniters and secondary burners are investigated in successful high-pressure oxy-methane combustion. The secondary burners are designed in such a way that it can operate between 100 to 500 kW firing input. Three generations of the pintle injector were designed based on swirl numbers (S=0, 0.9, and 1.2). Key pintle injector parameters such as pintle size, pintle orifice size, spray pattern were investigated by cold flow tests. Information from these tests was used to modify injector design for smooth and successful operation. A 5 mm pintle orifice size was decided upon as the optimum size for oxy-coal operation for the combustor. Shadow sizing experiments were performed to identify the atomization rate of each injector. Different coal water slurry mixtures (30 – 50% coal by wt% in the mixture) at various total momentum ratios (TMR) were investigated for this purpose. These experiments provided decisive information to choose the best design of the injector. The injector with 1.2 swirl provided higher atomization in all cases than other designs. The mean equivalent droplet size of the jet was similar at different TMR and mixture ratios using this injector, thus making it suitable for use in most cases. Therefore, the 1.2 swirl-pintle injector was chosen for the shakedown test. The combustor and other sub-systems, including feed systems and control and data acquisition, have been manufactured, assembled, and integrated. The total system integration and installation began on July 1, 2020. The shake-down tests and initial operational capability demonstration are expected to be completed by September 30, 2020.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Characterizing Hydraulic Fracture Propagation Before Fracture Hits

Estimating the distance from hydraulic fracture tip to monitor well can be very useful for fracture characterization, well spacing optimization, and preventing parent-child well interference. Heart-shape signal is referred to as the extensional precursor of fracture hit recorded by cross-well strain measurements and can be served as a vital tool to make such estimation. This study incorporates the 3D Displacement Discontinuity Method to understand the impact of fracture geometry and monitor well offset on the heart-shape signal’s characteristics. Results from numerical simulation and analytical solutions reveal a strong linear correlation between the spatial extent of heart shape signal and fracture tip distance. This relationship was further developed to predict tip distance using field data from the Hydraulic Fracture Test Site 2. A reasonable approximation result from field data further validates the methodology. In addition, it is worth noting that the estimation accuracy depends on the ratio between fracture dimension and tip distance. The findings of this study offer a novel approach for real-time monitoring and characterizing hydraulic fracture propagation, which can be further used for well spacing optimization in unconventional and Enhanced Geothermal System reservoir development, as well as cap rock integrity monitoring for carbon sequestration projects.

Jin, Ge↗
DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence V - Raw Data

Sequence V: Tip Plate (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 25 m/s, and the yaw angle was held at 0°. The blade pitch angle was 3°. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pre-tensioned to 40,000 N. During post-processing, the probe channels were set to read -99999.99. The standard tip blocks were replaced with a tip plate to simulate the effect of an undeployed tip-mounted aerodynamic brake as shown in Appendix A. Note that the blade radius was not changed during post-processing so the pressure tap locations are at the same radial location, but the reference to 30% represents 30% of 5.029 m, not 4.943 m. Throughout this report, references to the blade span are made for the 5.029- m radius, not the 4.943-m radius.

17 WIND ENERGY↗
DOE OSTI2020

Systems and methods for nano-tribological manufacturing of nanostructures

The presently disclosed subject matter provides systems and methods for generating nanostructures from tribological films. A probe tip can be immersed in a liquid mixture comprising a plurality of ink particles suspended in a medium. A substrate on which the tribological film is to be generated can also be immersed in the liquid mixture. A processor controlling movement of the probe tip can be configured to cause the probe tip to slide along the substrate in a shape of a desired pattern of the nanostructure with a contact force to cause one or more ink particles of the plurality of ink particles compressed underneath the probe tip to be transformed into a tribological film onto the substrate in the shape of the desired pattern of the nanostructure.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Design and Operability of a Pressurized Oxy Combustion System

Fossil fuel powers more than two-thirds of the world’s electricity, a significant share of which is derived from coal power plants. Despite coal being an abundant and energy-rich fuel, the major halt to its progress is greenhouse gas emissions. Pressurized oxy-combustion cycles can achieve theoretically high thermal efficiencies along with a 90% carbon capture rate. Additionally, the high energy density allows smaller turbomachinery and save capital cost. Thus, the primary objective of this dissertation is to present the design and operability of a pressurized oxy-combustor system. The initial part of the dissertation investigates different thermodynamic cycles and presents a model that can be adapted for existing power plants. The thermodynamic model will be used in the later part to design the proposed combustor. The two cycles analyzed are ENEL and TIPS. This study focuses on qualitative analyses of the cycles using a commercially available software called Aspen Plus®. A detailed benchmark study has been performed to validate the modeling process. ENEL and TIPS cycles are designed in the software, adopting the same principles. Recirculation ratio and pressures are varied to find the efficiency range of the cycles. Power calculations are done to find overall and net efficiency for a fixed recirculation ratio. The efficiencies of the cycles are compared to select an optimum cycle. A recirculation ratio of 50% is selected for implementation. The comparison shows that ENEL is marginally efficient over TIPS, at the cost of a pressure difference of about 70bars. Technology Readiness Level analysis is performed to present the availability of the specialized equipment for the cycles. From the TRL analysis, it is seen that the cost and availability of high viii pressure equipment surmount the edge of TIPS over ENEL. Thus, ENEL is chosen as the better cycle for investigating a scaled experiment considering efficiency and viability. The later part of the dissertation focuses on developing the combustor's design for a pressurized oxy-combustion cycle. The proposed combustor is a powerhead-mounted design aimed to produce 1MW of thermal outputThe different aspects of the design of a down-fired pressurized swirl combustor are presented in this dissertation.

Chowdhury, Mehrin↗
DOE OSTI2023

Triple bubbler system, fast-bubbling approach, and related methods

A triple bubbler system includes a first fluid probe, a second fluid probe, a third fluid probe, a gas source operably coupled to the first fluid probe, the second fluid probe, and the third fluid probe and configured to meter gas through the first fluid probe, the second fluid probe, and the third fluid probe to form bubbles at tips of each of the first fluid probe, the second fluid probe, and the third fluid probe, and a cover member disposed over the tips of the first, second, and third fluid probes and configured to at least partially prevent bubbles formed and escaping the tips of the first, second, and third fluid probes from interfering with other bubbles formed at each other tips. The bubbler system includes a thermocouple having a plurality of junctions disposed along an axis parallel to longitudinal axes of the first, second, and third fluid probes.

Galbreth, Gregory G.↗
DOE OSTI2025

Excitation Laser Energy Dependence of the Gap-Mode TERS Spectra of WS 2 and MoS 2 on Silver

In this work we present a systematic study of the dependence of the gap mode tip-enhanced Raman scattering (TERS) response of the mono- and bi-layer WS 2 and MoS 2 on silver as a function of the excitation laser energy in a broad spectral range from 473nm to 830 nm. For this purpose, we collected consecutive TERS maps of the same area in the sample containing mono-and bi-layer regions with the same TERS probe with 6 different excitation lasers. To decrease the number of collected TERS maps, we used for the first time to the best of our knowledge, concurrent excitation and collection with two lasers simultaneously. We found that the E 2g /A 1g peak intensity ratio for the bilayer WS 2 @Ag and the ratio of the A’/A 1g peak intensity of the out-of-plane mode for the mono- and the bilayer, change in a significantly non-monotonous way as the excitation laser energy is swept from 1.58 eV to 2.62 eV. The former ratio increases at energies corresponding to A and B excitons (~2.0 eV and 2.4 eV correspondingly) in bilayer WS 2 . The absolute intensity of the A’ peak in the monolayer, and correspondingly the A’/A 1g ratio, is surprisingly high at lower excitation energies, but dips dramatically at the energy corresponding to the A exciton, being restored partially in between A and B excitons, but still showing the descending trend as the excitation laser energy increases. A somewhat similar picture was observed in mono- and bi-layers of MoS 2 @Ag, though the existing set of excitation lasers did not match the excitonic profile of this material as nicely as for the case of WS 2 . We attribute the observed behavior to the presence of intermediate (Fano resonance) or strong (Rabi splitting) coupling between the excitons in transition metal dichalcogenides (TMDs) and the plasmons in the tip-substrate nanocavity. This is akin to the so-called Fano (Rabi) transparency experimentally observed in far field scattering from transition metal dichalcogenides between two plasmonic metals. The possibility of the formation of intermediate/strong coupling between the excitonic resonances in TMDs and the nanocavity re-evaluates the role of various resonances in the gap-mode TERS and should become an important factor to be considered by TERS practitioners during planning the experiments. Lastly, based on observed phenomena and its explanation, we propose the “ideal” substrate for efficient TERS and tip enhanced photoluminescence (TEPL) measurements.

Raman spectroscopy↗
DOE OSTI2023

Use of Nucleating Agent NA11 in the Preparation of Polyvinylidene Fluoride Dual-Layer Hollow Fiber Membranes

Polyvinylidene fluoride (PVDF) dual-layer hollow fiber membranes were simultaneously fabricated by thermally induced phase separation (TIPS) and non-solvent induced phase separation (NIPS) methods using a triple orifice spinneret (TOS) for water treatment application. The support layer was prepared from a TIPS dope solution, which was composed of PVDF, gamma-butyrolactone (GBL), and N-methyl-2-pyrrolidone (NMP). The coating layer was prepared from a NIPS dope solution, which was composed of PVDF, N,N-dimethylacetamide (DMAc), and polyvinylpyrrolidone (PVP). In order to improve the mechanical strength of the dual-layer hollow fiber, a nucleating agent, sodium 2,2'-methylene bis-(4,6-di-tert-butylphenyl) phosphate (NA11), was added to the TIPS dope solution. The performance of the membrane was evaluated by surface and cross-sectional morphology, water flux, mechanical strength, and thermal property. Our results demonstrate that NA11 improved the mechanical strength of the PVDF dual-layer hollow fiber membranes by up to 42%. In addition, the thickness of the coating layer affected the porosity of the membrane and mechanical performance to have high durability in enduring harsh processing conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive Manufacturing of Poly(phenylene Sulfide) Aerogels via Simultaneous Material Extrusion and Thermally Induced Phase Separation

Abstract Additive manufacturing (AM) of aerogels increases the achievable geometric complexity, and affords fabrication of hierarchically porous structures. In this work, a custom heated material extrusion (MEX) device prints aerogels of poly(phenylene sulfide) (PPS), an engineering thermoplastic, via in situ thermally induced phase separation (TIPS). First, pre‐prepared solid gel inks are dissolved at high temperatures in the heated extruder barrel to form a homogeneous polymer solution. Solutions are then extruded onto a room‐temperature substrate, where printed roads maintain their bead shape and rapidly solidify via TIPS, thus enabling layer‐wise MEX AM. Printed gels are converted to aerogels via postprocessing solvent exchange and freeze‐drying. This work explores the effect of ink composition on printed aerogel morphology and thermomechanical properties. Scanning electron microscopy micrographs reveal complex hierarchical microstructures that are compositionally dependent. Printed aerogels demonstrate tailorable porosities (50.0–74.8%) and densities (0.345–0.684 g cm −3 ), which align well with cast aerogel analogs. Differential scanning calorimetry thermograms indicate printed aerogels are highly crystalline (≈43%), suggesting that printing does not inhibit the solidification process occurring during TIPS (polymer crystallization). Uniaxial compression testing reveals that compositionally dependent microstructure governs aerogel mechanical behavior, with compressive moduli ranging from 33.0 to 106.5 MPa.

Chemistry↗
DOE OSTI2024

Adaptive Scalpel Scanning Probe Microscopy for Enhanced Volumetric Sensing in Tomographic Analysis

Controlling nanoscale tip‐induced material removal is crucial for achieving atomic‐level precision in tomographic sensing with atomic force microscopy (AFM). While advances have enabled volumetric probing of conductive features with nanometer accuracy in solid‐state devices, materials, and photovoltaics, limitations in spatial resolution and volumetric sensitivity persist. This work identifies and addresses in‐plane and vertical tip‐sample junction leakage as sources of parasitic contrast in tomographic AFM, hindering real‐space 3D reconstructions. Novel strategies are proposed to overcome these limitations. First, the contrast mechanisms analyzing nanosized conductive features are explored when confining current collection purely to in‐plane transport, thus allowing reconstruction with a reduction in the overestimation of the lateral dimensions. Furthermore, an adaptive tip‐sample biasing scheme is demonstrated for the mitigation of a class of artefacts induced by the high electric field inside the thin oxide when volumetrically reduced. This significantly enhances vertical sensitivity by approaching the intrinsic limits set by quantum tunneling processes, allowing detailed depth analysis in thin dielectrics. The effectiveness of these methods is showcased in tomographic reconstructions of conductive filaments in valence change memory, highlighting the potential for application in nanoelectronics devices and bulk materials and unlocking new limits for tomographic AFM.

36 MATERIALS SCIENCE↗
DOE OSTI2024

3D‐Printed Carbon Nanoneedle Electrodes for Dopamine Detection in Drosophila

In vivo electrochemistry in small brain regions or synapses requires nanoelectrodes with long straight tips for submicron scale measurements. Nanoelectrodes can be fabricated using a Nanoscribe two-photon printer, but annealed tips curl if they are long and thin. We propose a new pulling-force strategy to fabricate a straight carbon nanoneedle structure. A micron-width bridge is printed between two blocks. The annealed structure shrinks during pyrolysis, and the blocks create a pulling force to form a long, thin, and straight carbon bridge. Parameterization study and COMSOL modeling indicate changes in the block size, bridge size and length affect the pulling force and bridge shrinkage. Electrodes were printed on niobium wires, insulated with aluminum oxide, and the bridge cut with focused ion beam (FIB) to expose the nanoneedle tip. Annealed needle diameters ranged from 400 nm to 5.25 μm and length varied from 50.5 μm to 146 μm. The electrochemical properties are similar to glassy carbon, with good performance for dopamine detection with fast-scan cyclic voltammetry. Nanoelectrodes enable biological applications, such as dopamine detection in a specific Drosophila brain region. Long and thin nanoneedles are generally useful for other applications such as cellular sensing, drug delivery, or gas sensing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Nonlinear Nano‐Imaging of Interlayer Coupling in 2D Graphene‐Semiconductor Heterostructures

The emergent electronic, spin, and other quantum properties of 2D heterostructures of graphene and transition metal dichalcogenides are controlled by the underlying interlayer coupling and associated charge and energy transfer dynamics. However, these processes are sensitive to interlayer distance and crystallographic orientation, which are in turn affected by defects, grain boundaries, or other nanoscale heterogeneities. This obfuscates the distinction between interlayer charge and energy transfer. Here, nanoscale imaging in coherent four‐wave mixing (FWM) and incoherent two‐photon photoluminescence (2PPL) is combined with a tip distance‐dependent coupled rate equation model to resolve the underlying intra‐ and inter‐layer dynamics while avoiding the influence of structural heterogeneities in mono‐ to multi‐layer graphene/WSe 2 heterostructures. With selective insertion of hBN spacer layers, it is shown that energy, as opposed to charge transfer, dominates the interlayer‐coupled optical response. From the distinct nano‐FWM and ‐2PPL tip‐sample distance‐dependent modification of interlayer and intralayer relaxation by tip‐induced enhancement and quenching, an interlayer energy transfer time of τ ET ≈ ( 0 . 35 − 0.15 + 0.65 ) $\tau _{\rm ET} \approx (0.35^{+0.65}_{-0.15})$ ps consistent with recent reports is derived. As a local probe technique, this approach highlights the ability to determine intrinsic sample properties even in the presence of large sample heterogeneity.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

Parked aeroelastic field rotor response for a 20% scaled demonstrator of a 13‐MW downwind turbine

Abstract Aeroelastic parked testing of a unique downwind two‐bladed subscale rotor was completed to characterize the response of an extreme‐scale 13‐MW turbine in high‐wind parked conditions. A 20% geometric scaling was used resulting in scaled 20‐m‐long blades, whose structural and stiffness properties were designed using aeroelastic scaling to replicate the nondimensional structural aeroelastic deflections and dynamics that would occur for a lightweight, downwind 13‐MW rotor. The subscale rotor was mounted and field tested on the two‐bladed Controls Advanced Research Turbine (CART2) at the National Renewable Energy Laboratory's Flatiron Campus (NREL FC). The parked testing of these highly flexible blades included both pitch‐to‐run and pitch‐to‐feather configurations with the blades in the horizontal braked orientation. The collected experimental data includes the unsteady flapwise root bending moments and tip deflections as a function of inflow wind conditions. The bending moments are based on strain gauges located in the root section, whereas the tip deflections are captured by a video camera on the hub of the turbine pointed toward the tip of the blade. The experimental results are compared against computational predictions generated by FAST, a wind turbine simulation software, for the subscale and full‐scale models with consistent unsteady wind fields. FAST reasonably predicted the bending moments and deflections of the experimental data in terms of both the mean and standard deviations. These results demonstrate the efficacy of the first such aeroelastically scaled turbine test and demonstrate that a highly flexible lightweight downwind coned rotor can be designed to withstand extreme loads in parked conditions.

17 WIND ENERGY↗