Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Superconducting magnet”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Magnetic Levitators With Superconductive Components

Magnetic noncontact levitators that include superconductive components provide vibration-damping suspension for cryogenic instruments, according to proposal. Because superconductive components attached to levitated cryogenic instruments, no additional coolant liquid or refrigeration power needed. Also because vibration-damping components of levitators located outside cold chambers, in ambient environment, not necessary to waste coolant liquid or refrigeration power on dissipation of vibrational energy. At least three levitating magnets and three superconductors necessary for stable levitation.

Dolgin, Benjamin P.↗
DOE OSTI2022

Multi-scale nonlinear stress analysis of Nb 3 Sn superconducting accelerator magnets

A multi-scale nonlinear procedure to analyze the stress in Nb 3 Sn superconducting accelerator magnets is presented to address one of the most challenging obstacles currently facing the successful development of high-field superconducting magnets—the issue of stress management. The study demonstrates that gaskets (special nonlinear materials) are capable of modeling the complex nonlinear deformation behavior of insulation layers within the Nb 3 Sn coil block and that Hill materials (orthotropic materials utilizing the Hill yield criterion) are suitable to enable homogenization of the filamentary regions and the resin-impregnated Nb 3 Sn Rutherford cables. With the whole magnet under preload, cool-down, and Lorentz forces, the nonlinear behavior of the Nb 3 Sn coil was simulated, in three orthongonal axes, by the combined properties of the gaskets (insulation layers) and Hill materials (resin-impreganted cable). The procedure entailes minimal material assumptions because it incorporated measured stress-strain curves in the analysis. The coil was simulated to a high level of detail consisting of the insulation layers and resin-impregnated cables. The computed compressive azimuthal stresses of the cables were used to assess the stress-induced performance degradation. Through submodeling, the area-weighted average axial strains of the strands were computed and employed to evaluate the strain-induced performance degradation. The overall performance degradation of the Nb 3 Sn coil was thus obtained, and this information was subsequently used to guide the design of the overall magnet. Besides Nb 3 Sn magnets, this procedure can also be employed in the design of LTS, HTS, and room temperature magnets or in any composite structures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Distributed fiber-optic sensing in a subscale high-temperature superconducting dipole magnet

High-temperature superconductors, such as REBa2Cu3O7−x (REBCO, RE = rare earth), are becoming pivotal for high-field magnet technology for future circular colliders and compact fusion reactors. The U.S. Magnet Development Program, in collaboration with industry, is developing REBCO magnet technology using round conductors consisting of multiple REBCO tapes. For these multi-tape cables, traditional instrumentation, such as voltage taps and resistive strain gauges, become insufficient to help measure and understand the performance-limiting factors in these model magnets. Distributed fiber-optic sensing (DFOS) is a potential solution to address this challenge. Although DFOS is well established for various applications, measuring temperature and strain in high-temperature superconducting magnets is in its infancy. Here we report the detailed implementation and test results of DFOS based on Rayleigh scattering in a subscale canted cosθ (CCT) dipole magnet using high-temperature superconducting CORC® wires. We co-wound optical fibers in each layer of the CCT magnet and compared different types of commercial fibers and mold-release agents to reduce the power attenuation in the fibers. The DFOS allowed us to measure mechanical deformation and temperature along the conductor during tests at 77 and 4.2 K. The measured strain agreed quantitively with a finite-element mechanical model of the subscale magnet. Our results indicate that DFOS can effectively identify locations of strain and temperature changes, offering unique insight into magnet performance that can advance our understanding and development of the REBCO magnet technology for high-energy physics and fusion applications.

Luo, Linqing↗
NASA NTRSDate not supplied

Evaluation of Magnet Configurations for Magnetohydrodynamic Trajectory Control during Planetary Entry

Magnetohydrodynamics is a phenomenon that can be harnessed during planetary entry to augment aerodynamic drag and may enable higher mass payloads to safely reach the surface. The magnetohydrodynamic force is quantified over a wide range of freestream conditions using computational fluid dynamics results from a previous study. The force is calculated for an array of small electromagnets, a large non-superconducting magnet, a large superconducting magnet, and a uniform field. The superconducting magnet produces a magnetohydrodynamic force within an order of magnitude of aerodynamic drag for velocities higher than 10 km/s, indicating that it may have a reasonable impact on the trajectory for some cases. The array of small magnets and non-superconducting magnet produced a magnetohydrodynamic force that is less than 1% of the aerodynamic drag, so their magnetic fields are not strong enough to affect an entry trajectory. Additionally, the magnet placement plays an important role in magnetohydrodynamic force magnitude, with a magnet located near the shoulder producing approximately eight times more force than a magnet placed on the axis of symmetry. A mass and power budget for each magnet configuration is given assuming current state-of-the-art magnet technology. This study also discusses implementation challenges for each type of magnet on a spacecraft.

Magnetohydrodynamics↗
NASA NTRS1979

Space applications of superconductivity - High field magnets

The paper discusses developments in superconducting magnets and their applications in space technology. Superconducting magnets are characterized by high fields (to 15T and higher) and high current densities combined with low mass and small size. The superconducting materials and coil design are being improved and new high-strength composites are being used for magnet structural components. Such problems as maintaining low cooling temperatures (near 4 K) for long periods of time and degradation of existing high-field superconductors at low strain levels can be remedied by research and engineering. Some of the proposed space applications of superconducting magnets include: cosmic ray analysis with magnetic spectrometers, energy storage and conversion, energy generation by magnetohydrodynamic and thermonuclear fusion techniques, and propulsion. Several operational superconducting magnet systems are detailed.

Fickett, F. R.↗
NASA NTRS1993

The role of superconductivity in magnetic bearings for high-load applications

Slewing of large payloads will require control torque and angular momentum storage capacities that are large in comparison to the capabilities of available control moment gyros (CMG's). SatCon Technology Corporation is currently designing a CMG which may be employed as a slew actuator for large spacecraft or other payloads. The slew actuator employs a type of magnetic bearing which may be used in high load applications. The magnetic bearing is also used to fully gimbal the suspended rotor of the slew actuator. The use of magnetic bearings in angular momentum exchange actuators has the primary advantage that physical contact between the rotor and stator is eliminated. This leads to greatly extended life, increased reliability, and reduced vibrations. Several actuators operating on magnetic bearings have been demonstrated in previous research efforts. These were sized for use in small satellites. For conventional magnetic bearings, which employ magnetic cores, high torsional loading may require that the magnetic structure be excessively massive. An alternative magnetic bearing design which employs a superconducting coil and eliminates conventional magnetic structures is discussed. The baseline approach is to replace the field coil of a conventional magnetic bearing with the superconducting coil.

Downer, James↗
DOE OSTI2022

Fiber-optic diagnostic system for future accelerator magnets

The next generation high energy physics accelerators will require magnetic fields at ~20 T. HTS coils will be an essential component of future accelerator magnets and several efforts are currently dedicated on designing 20 T HTS- LTS hybrid magnets. Among the existing challenges, there is the lack of a robust quench detection system for hybrid magnet technology. Another big challenge is represented by the high number of training quenches required by Nb3Sn magnets to reach performance level. In this framework it is important to find a tool that allow local real-time monitoring of magnet strain and temperature. In this paper, we propose the use of fiber optics sensors for diagnostic and quench detection in future accelerator superconducting magnets. Discrete and distributed fiber optic sensors have demonstrated to be a promising tool. The goal is to instrument hundreds of accelerator superconducting magnets and to move beyond the proof-of-concept level. Significant developments are still needed. Here, we are going to present the most recent results and discuss the most urgent technical developments in order to make those sensors a robust and reliable diagnostic tool for accelerator superconducting magnets over the next 10 year. We foresee that discrete fiber sensors will be a stable diagnostic probe for superconducting magnets over the next 3 to 5 years. More R&D work will be necessary for distributed fibers. The most urgent needs are the increase of sample rate and sensitivity. Close collaboration with vendors will be necessary to improve mechanical properties and fabrication processes in order to produce hundreds of meters of fiber and instrument a large number of accelerator superconducting magnets. Those R&D efforts will last up to 10 years with a founding level that spans between 5-10 M$.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Superconductivity and magnetic and transport properties of single-crystalline CaK ( Fe 1 – x Cr x ) 4 As 4

Members of the CaK (Fe 1–x Cr x ) 4 As 4 series have been synthesized by high-temperature solution growth in single-crystalline form and characterized by x-ray diffraction, elemental analysis, and magnetic and transport measurements. The effects of Cr substitution on the superconducting and magnetic ground states of CaKFe 4 As 4 (T c = 35 K) have been studied. These measurements show that the superconducting transition temperature decreases monotonically and is finally suppressed below 1.8 K as x is increased from 0 to 0.038. For x-values greater than 0.012, signatures of a magnetic transition can be detected in magnetic measurements with the associated features in the transport measurements becoming detectable for x ≥ 0.038. The magnetic transition temperature increases in a roughly linear manner as Cr substitution increases. A temperature-composition (T – x) phase diagram is constructed, revealing a half-dome of superconductivity with the magnetic transition temperature, T*, appearing near 22 K for x ~ 0.017 and rising slowly up to 60 K for x ~ 0.077. The T – x phase diagrams for CaK (Fe 1–x T x ) 4 As 4 for T = Cr and Mn are essentially the same despite the nominally different band filling; this is in marked contrast to T = Co and Ni series for which the T – x diagrams scale by a factor of 2, consistent with the different changes in band filling Co and Ni would produce when replacing Fe. Superconductivity of CaK (Fe 1–x Cr x ) 4 As 4 is also studied as a function of magnetic field. A clear change in $H^{'}_{c2}$ (T)/T c , where $H^{'}_{c2}$ (T) is dH c2 (T)/dT, at x ~ 0.012 is observed and probably is related to a change of the Fermi surface due to magnetic order. Further, coherence length and the London penetration depths are also calculated based on H c1 and H c2 data. Both of them as a function of x show changes near x = 0.012, again consistent with Fermi surface changes associated with the magnetic ordering seen for higher x-values.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Quantum Magnetic Properties and Metal‐to‐Insulator Transition in Chemically Doped Calcium Ruthenate Perovskite

Ruthenates provide a comprehensive platform to study a plethora of novel properties, such as quantum magnetism, superconductivity, and magnetic fluctuation mediated metal–insulator transition (MIT). Herein, an overview of quantum mechanical phenomenology in calcium ruthenium oxide with varying compositions is provided. While the stoichiometric composition of exhibits non‐fermi liquid (FL) behavior with quasi‐criticality, chemically doped compounds depict prominent signatures of quantum magnetic fluctuations at low temperature that in some cases are argued to mediate in metal–insulator transition. In the case of cobalt‐doped , an unusual continuum fluctuation is found to persist deep inside the glassy phase of the material. These observations reflect the richness of the ruthenate research platform in the study of quantum magnetic phenomena of fundamental importance.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

2 Kelvin helium distribution system for the Electron Ion Collider’s 10 o’clock satellite refrigerator

The Electron-Ion Collider (EIC) at Brookhaven National Laboratory (BNL) will involve superfluid helium cooling of superconducting magnets and Superconducting Radio Frequency (SRF) cavities at several sites around the existing Relativistic Heavy Ion Collider (RHIC) accelerator tunnel. While the majority of the cooling power for these loads is provided by BNL’s central cryogenic plant, Jefferson Lab is designing satellite equipment which augments the central plant and enables 2 Kelvin operation. The 2 K cryogenic distribution system for the collider’s 10 o’clock location (Interaction Region 10 or IR10) includes all necessary interfaces to the IR10 Satellite Refrigerator, to the overall EIC cryogenic distribution system, and to 12 SRF cryomodules for the electron and hadron storage rings. In addition to providing the required cooling capacities in all operating modes, the IR10 2 K cryogenic distribution system also stabilizes the supply temperature and enables safe connection and disconnection of individual IR10 cryomodules. Moreover, the layout of the IR10 2 K cryogenic distribution system copes with challenging spatial constraints and adapts to the process configuration and routing of existing RHIC cryogenic distribution components which will be re-used for EIC. This paper gives a full overview of the IR10 satellite cryogenic distribution system design, and highlights some of the challenges encountered.

Laverdure, Nathaniel [Thomas Jefferson National Ac↗
DOE OSTI2022

REBCO -- a silver bullet for our next high-field magnet and collider budget?

High-field superconducting magnets with a dipole field of 16 T and above enable future energy-frontier circular particle colliders. Although we believe these magnets can be built, none exists today. They can also be a showstopper for future high-energy machines due to a prohibitively high price tag based on the current conductor and magnet fabrication cost. The high-temperature superconducting REBCO coated conductor can address both the technical and cost issues, a silver bullet to lay both monsters to rest. The challenges and unknowns, however, can be too arduous to make the silver bullet. We lay out a potential road forward and suggest key action items. As a contribution from the accelerator community, we attempt to clarify for our theorist and experimenter colleagues a few aspects about the future high-field superconducting magnets. We hope to stimulate an effective plan for the 2023 P5 process that can lead to a cost-effective high-field magnet technology for future colliders and the exciting physics they can steward.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Study of Conduction-Cooled Superconducting Quadrupole Magnets Combined with Dipole Correctors for the ILC Main Linac

A superconducting rf (SRF) cryomodule for International Linear Collider(ILC) Main Linac equips focus/steering magnets. The magnets are "superferric" magnets with four superconducting (SC) race track coils conductively cooled from the cryomodule LHe supply pipe. The quadrupole field gradient and dipole field are 40 T/m and 0.1 T, respectively. The magnet length and iron-pole radius are 1 m and 0.045 m, respectively. It is known that dark current is generated at SRF cavities and accelerated through the following linac string. The dark current reaches and heats the SC magnets. It is estimated that the power deposition in the magnet may reach more than a few watts and temperature of the SC coils may locally reach to critical temperature of NbTi. It is important to make the magnet not reach quench with sufficient conduction cooling. We aim to realize the SC magnet which can stably operate under such condition. We plan to develop test coils made of three types of SC materials, NbTi, Nb₃Sn, and MgB₂ and study thermal characteristics and stability . We will develop a short model magnet, based on the test coil results. Here, we will present the magnet design study and the R&D plan.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Pulsed Power Supply for Magnet Quench Training

Superconducting magnets typically go through aseries of spontaneous “training” quenches as their current isincreased towards its design value. To decrease the number ofthese quenches, a device has been designed to boost the magnetcurrent at the moment a quench has been detected and beforemagnet protection has been initiated. The aim of the boost is todrive the magnet coil further along towards its maximum currentwith each training quench, and hence reduce the number ofquenches required.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

The Design of B1APF Dipole for the EIC

Brookhaven National Laboratory has been chosen to host the Electron-Ion Collider (EIC). Part of this is to install an additional electron ring to the existing RHIC tunnel. The electron hadron Interaction Region (IR) will host nine superconducting magnets on the forward side and six superconducting magnets on the rear side of the Interaction Point (IP). B1APF dipole is the last magnet of the near IR in the outgoing hadron direction. Further, the magnet has a physical aperture of 370 mm diameter and is 1.5 m long. This large aspect ratio makes this magnet particularly challenging. It is a collared magnet and uses a NbTi Rutherford cable with 15.1 mm X 1.9 mm. It is expected to operate at a maximum current of 13400 A at 2 K. The required integrated dipole field is 4.05 Tm. This paper discusses the current design status of the B1ApF dipole and presents the electromagnetic analysis and thermal quench propagation analysis.

43 PARTICLE ACCELERATORS↗
NASA NTRS2012

A Reversible Thermally Driven Pump for Use in a Sub-Kelvin Magnetic Refrigerator

A document describes a continuous magnetic refrigerator that is suited for cooling astrophysics detectors. This refrigerator has the potential to provide efficient, continuous cooling to temperatures below 50 mK for detectors, and has the benefits over existing magnetic coolers of reduced mass because of faster cycle times, the ability to pump the cooled fluid to remote cooling locations away from the magnetic field created by the superconducting magnet, elimination of the added complexity and mass of heat switches, and elimination of the need for a thermal bus and single crystal paramagnetic materials due to the good thermal contact between the fluid and the paramagnetic material. A reliable, thermodynamically efficient pump that will work at 1.8 K was needed to enable development of the new magnetic refrigerator. The pump consists of two canisters packed with pieces of gadolinium gallium garnet (GGG). The canisters are connected by a superleak (a porous piece of VYCOR glass). A superconducting magnetic coil surrounds each of the canisters. The configuration enables driving of cyclic thermodynamic cycles (such as the sub-Kelvin Active Magnetic Regenerative Refrigerator) without using pistons or moving parts.

Miller, Franklin K.↗
DOE OSTI2022

Current distribution monitoring enables quench and damage detection in superconducting fusion magnets

Abstract Fusion magnets made from high temperature superconducting ReBCO CORC ® cables are typically protected with quench detection systems that use voltage or temperature measurements to trigger current extraction processes. Although small coils with low inductances have been demonstrated, magnet protection remains a challenge and magnets are typically operated with little knowledge of the intrinsic performance parameters. We propose a protection framework based on current distribution monitoring in fusion cables with limited inter-cable current sharing. By employing inverse Biot-Savart techniques to distributed Hall probe arrays around CORC ® Cable-In-Conduit-Conductor (CICC) terminations, individual cable currents are recreated and used to extract the parameters of a predictive model. These parameters are shown to be of value for detecting conductor damage and defining safe magnet operating limits. The trained model is then used to predict cable current distributions in real-time, and departures between predictions and inverse Biot-Savart recreated current distributions are used to generate quench triggers. The methodology shows promise for quality control, operational planning and real-time quench detection in bundled CORC ® cables for compact fusion reactors.

47 OTHER INSTRUMENTATION↗