Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Structural beams”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Space fabrication demonstration system, technical volume

The automatic beam builder ABB was developed, fabricated, and demonstrated within the established contract cost and schedule constraints. The ABB demonstrated the feasibility of: producing lightweight beams automatically within the required rate of 1 to 5 ft of completed beam per minute and producing structurally sound beams with axial design load of 5538 N based on the Grumman photovoltaic satellite solar power system design reference structure.

Source record↗
DOE OSTI2025

LEBT Chopper System: System Design Document (SDD)

The Low Energy Beam Transport (LEBT) chopper creates a required beam time structure by chopping out (removing by deflecting from the beam path) unwanted parts of a continuous beam transported from the ion source to RFQ in LEBT. The unchopped parts of the beam propagate through the LEBT, while the deflected parts are deposited on an absorbing target. The chopper system in general consists of a deflecting structure, where the beam-deflecting fields are created, and a pulse generator that feeds this structure with voltage pulses having the required time pattern. The system should turn deflection on and off within a short time interval, because the beam parts within the pulse front and end will be only partially deflected and will form unwanted tails of the beam pulse downstream. This can be achieved with traveling slow-wave chopper structures where the field propagates with the same velocity as the beam, as illustrated in Fig. 1.

43 PARTICLE ACCELERATORS↗
NASA NTRS1984

Section 1. Method of determining mode shapes and natural frequencies of the NASA unmodified test structure. Section 2. Continuous beam closed from solution to the NASA-LSS astromast torsional vibration, appendix E

The methods used to determine the lower natural frequencies and their corresponding mode shapes of the NASA-LSS Astromast (Unmodified Test Structure), and the mass integrals associated with the mode shapes are illustrated. The test structure is modeled as a cantilever beam with 91 lumped masses and without the tip mass on the free end of the bram. This uncouples the torsion and bending modes and allows for them to be determined separately. The frequency range was limited to an upper bound of 100 rad/sec (15.92 Hz.). In this range from 0.-100. rad/sec, three bending frequencies and one torsion frequency was found.

Source record↗
NASA NTRS1984

Static shape determination and control for large space structures. I - The flexible beam. II - A large space antenna

A method for determining and controlling the shape of large, continuous space structures by means of discrete or pointwise observations and control devices is presented. The general linear boundary value problem satisfied by a one-dimensional shape function is defined, and the existence of solutions is studied. The static shape control problems for one-dimensional systems with and without rigid body modes and the static shape estimation problem are presented and solved. Eigenfunction expansions are presented which provide approximations to the algorithm terms when the associated Green's function is not known. An integral operator approach is applied to the multidimensional static problem, and the results are illustrated with a finite element model of the disk of a large space antenna which assumes no rigid body modes. It is shown that the shape control algorithm must be modified for systems with rigid body modes.

Weeks, C. J.↗
DOE OSTI2024

Finite element procedure for thermomechanical and structural integrity analysis of beam intercepting devices subjected to free electron laser

High-energy particles, including photons (x-ray, γ-ray, bremsstrahlung), electrons, and protons, possess the capability to penetrate materials and deposit energy within them. The degree of absorption depends on both the energy and type of particles, as well as the properties of the materials with which they interact. This energy deposition can manifest either at the material's surface or throughout its volume, potentially resulting in various failure modes. The primary aim of this paper is to establish a structured analysis methodology for evaluating the structural integrity of beam-intercepting devices when subjected to high-energy particles. Here, the paper also reviews some of the underlying physics, pertinent to the scope of the thermomechanical analysis, potential failure modes, and introduces verification and validation methodologies. Engineers and researchers can utilize the guidelines presented in this paper to effectively plan the development of beam intercepting devices, thereby ensuring their reliability and performance in the presence of high-energy particle exposure.

Finite element analysis↗
DOE OSTI2021

Generation of structured coherent extreme ultraviolet beams from an MgO crystal

Short wavelength high-harmonic sources are undergoing intense development for applications in spectroscopy and microscopy. Despite recent progress in peak and average power, spatial control over coherent extreme ultraviolet (XUV) beams remains a formidable challenge due to the lack of suitable optical elements for beam shaping and control. In this work, we demonstrate a robust and precise approach that structures XUV high-order harmonics in space as they are emitted from a nanostructured MgO crystal. Our demonstration paves the way for bridging the numerous applications of shaped light beams from the visible to the short wavelengths, with potential uses for applications in microscopy and nanoscale machining.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Reflection of light beams from a chirped dielectric plane-layered structure

The reflection of light beams with various widths of the angular spectrum from a chirped plane-layered dielectric structure is numerically studied. For wide beams, the total lateral shift of the reflected beam depends on the position of the photonic barrier inside the structure and the value of the Goos – Hänchen shift. For narrow beams, the region of the interaction with the structure increases, the profile broadens and the reflected beam wavefront becomes phase modulated. It is shown that the light reflected from a quasi-periodic structure with negative spatial dispersion undergoes focusing. (light beams)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1995

Compensation of Gravity-Induced Structural Deformations on a Beam- Waveguide Antenna Using a Deformable Mirror

At the NASA Deep Space Network (DSN) Goldstone Complex, a 34-meter- diameter beam-waveguide antenna, DSS-13, was constructed in 1988-1990 and has become an integral part of an advanced systems program and a test bed for technologies being developed to introduce Ka-band (32 GHz) frequencies into the DSN. A method for compensating the gravity- induced structural deformations in this large antenna is presented.

technologies DSN↗
NASA NTRS1978

Gamma ray facilities at the University of Maryland cyclotron

A special beam line was set up in a separate shielded experimental room to provide a low background station for gamma-ray measurements at the University of Maryland cyclotron. The transmitted beam leaving the target is gathered in by a magnetic quadrupole lens located 1.8 m further downstream and focused on a Faraday cup located on the far side of the 2.5 m thick concrete shielding wall of the experimental room. A software computer program permits timing information ot be obtained using the cyclotron beam fine structure as a time reference for the observed gamma-ray events. Measurements indicate a beam fine structure width of less than 1.2 nanoseconds repeated, for example, in the case of 140 MeV alpha particles every 90 nanoseconds. Twelve contiguous time channels of adjustable width may be set as desired with reference to the RF signal. This allows the creation of 12 separate 8192 channel analyzers.

Hornyak, W. F.↗
DOE OSTI2017

Generation of Ramped Current Profiles in Relativistic Electron Beams Using Wakefields in Dielectric Structures

We show that temporal pulse tailoring of charged-particle beams is essential to optimize efficiency in collinear wakefield acceleration schemes. In this Letter, we demonstrate a novel phase space manipulation method that employs a beam wakefield interaction in a dielectric structure, followed by bunch compression in a permanent magnet chicane, to longitudinally tailor the pulse shape of an electron beam. This compact, passive, approach was used to generate a nearly linearly ramped current profile in a relativistic electron beam experiment carried out at the Brookhaven National Laboratory Accelerator Test Facility. Here, we report on these experimental results including beam and wakefield diagnostics and pulse profile reconstruction techniques.

43 PARTICLE ACCELERATORS↗
NASA NTRS1988

Molecular beam epitaxial growth and structural characterization of ZnS on (001) GaAs

The effect of surface nucleation processes on the quality of ZnS layers grown on (001) GaAs substrates by molecular beam epitaxy is reported. Reflection high energy electron diffraction indicated that nucleation at high temperatures produced more planar surfaces than nucleation at low temperatures, but the crystalline quality as assessed by X-ray double crystal diffractometry is relatively independent of nucleation temperature. A critical factor in layer quality was the initial roughness of the GaAs surfaces.

Benz, R. G., II↗
DOE OSTI2016

Giant amplification in degenerate band edge slow-wave structures interacting with an electron beam

We propose a new amplification regime based on a synchronous operation of four degenerate electromagnetic (EM) modes in a slow-wave structure and the electron beam, referred to as super synchronization. These four EM modes arise in a Fabry-Pérot cavity when degenerate band edge (DBE) condition is satisfied. The modes interact constructively with the electron beam resulting in superior amplification. In particular, much larger gains are achieved for smaller beam currents compared to conventional structures based on synchronization with only a single EM mode. We demonstrate giant gain scaling with respect to the length of the slow-wave structure compared to conventional Pierce type single mode traveling wave tube amplifiers. We construct a coupled transmission line model for a loaded waveguide slow-wave structure exhibiting a DBE, and investigate the phenomenon of giant gain via super synchronization using the Pierce model generalized to multimode interaction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1983

Design procedures for fiber composite structural components: Rods, columns and beam columns

Step by step procedures are described which are used to design structural components (rods, columns, and beam columns) subjected to steady state mechanical loads and hydrothermal environments. Illustrative examples are presented for structural components designed for static tensile and compressive loads, and fatigue as well as for moisture and temperature effects. Each example is set up as a sample design illustrating the detailed steps that are used to design similar components.

Chamis, C. C.↗
DOE OSTI2016

Hollow structure formation of intense ion beams with sharp edge in background plasmas

The transport of intense ion beams with sharp radial beam edge in plasmas has been studied with two-dimensional electromagnetic particle simulations. The initial solid beam evolves into a hollow beam due to the nonlinear sharp transverse force peak in the regions of beam edge. The magnitude and nonlinearity of this peak are enhanced as the ion beam travels further into the plasma, due to the self-consistent interactions between the beam ions and the plasma electrons. This structure formation is shown to be independent on the beam radius.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1988

Electric potential structures and propagation of electron beams injected from a spacecraft into a plasma

One-dimensional Vlasov simulations are used to study the propagation of electron beams injected from a spacecraft into an ambient plasma and the associated potential structures. It is shown that, for a given beam velocity, the propagation velocity and the potential structure depends on the beam density. In the case of moderate beams, a double layer forms near the beam head which propagates into the ambient plasma much more slowly than the initial beam velocity.

Singh, Nagendra↗
DOE OSTI2024

Efficient generation and amplification of intense vortex and vector laser pulses via strongly-coupled stimulated Brillouin scattering in plasmas

The past decade has seen tremendous progress in the production and utilization of vortex and vector laser pulses. Although both are considered as structured light beams, the vortex lasers have helical phase fronts and phase singularities, while the vector lasers have spatially variable polarization states and polarization singularities. In contrast to the vortex pulses that carry orbital angular momentum (OAM), the vector laser pulses have a complex spin angular momentum (SAM) and OAM coupling. Despite many potential applications enabled by such pulses, the generation of high-power/-intensity vortex and vector beams remains challenging. Here, we demonstrate using theory and three-dimensional simulations that the strongly-coupled stimulated Brillouin scattering (SC-SBS) process in plasmas can be used as a promising amplification technique with up to 65% energy transfer efficiency from the pump beam to the seed beam for both vortex and vector pulses. We also show that SC-SBS is strongly polarization-dependent in plasmas, enabling an all-optical polarization control of the amplified seed beam. Additionally, the interaction of such structured lasers with plasmas leads to various angular momentum couplings and decouplings that produce intense new light structures with controllable OAM and SAM. This scheme paves the way for novel optical devices such as plasma-based amplifiers and light field manipulators.

Physics↗