Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Spatial Temporal Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Comparison and analysis of aircraft measurements and mesoscale atmospheric chemistry model simulations of tropospheric ozone

The Regional Acid Deposition Model (RADM) has been applied to several of the field experiments which were part of the Acid Models Operational and Diagnostic Evaluation Study (Acid MODES). The experiment which was of particular interest with regards to ozone photochemistry involved horizontal zig-zag flight patterns (ZIPPER) over an area from the eastern Ohio River valley to the Adirondacks of New York. Model simulations by both the standard resolution RADM (delta x = 80 km) and the nested grid RADM (delta x = 26.7 km) compare well to measurements in the low emission regions in central Pennsylvania and upstate New York, but underestimate in the high emission upper Ohio River valley. The nested simulation does considerably better, however, than the coarse grid simulation in terms of horizontal pattern and concentration magnitudes. Analysis of NO(x) and HO(x) concentrations and photochemical products rates of ozone show that the model's response to large point source emissions is very unsystematic both spatially and temporally. This is due to the models instability to realistically simulate the small scale (subgrid) gradients in precursor concentrations in and around large point source plumes.

Pleim, Jonathan E.↗
NASA NTRS2001

The Numerical Analysis of a Turbulent Compressible Jet

A numerical method to simulate high Reynolds number jet flows was formulated and applied to gain a better understanding of the flow physics. Large-eddy simulation was chosen as the most promising approach to model the turbulent structures due to its compromise between accuracy and computational expense. The filtered Navier-Stokes equations were developed including a total energy form of the energy equation. Subgrid scale models for the momentum and energy equations were adapted from compressible forms of Smagorinsky's original model. The effect of using disparate temporal and spatial accuracy in a numerical scheme was discovered through one-dimensional model problems and a new uniformly fourth-order accurate numerical method was developed. Results from two- and three-dimensional validation exercises show that the code accurately reproduces both viscous and inviscid flows. Numerous axisymmetric jet simulations were performed to investigate the effect of grid resolution, numerical scheme, exit boundary conditions and subgrid scale modeling on the solution and the results were used to guide the three-dimensional calculations. Three-dimensional calculations of a Mach 1.4 jet showed that this LES simulation accurately captures the physics of the turbulent flow. The agreement with experimental data was relatively good and is much better than results in the current literature. Turbulent intensities indicate that the turbulent structures at this level of modeling are not isotropic and this information could lend itself to the development of improved subgrid scale models for LES and turbulence models for RANS simulations. A two point correlation technique was used to quantify the turbulent structures. Two point space correlations were used to obtain a measure of the integral length scale, which proved to be approximately 1/2 D(sub j). Two point space-time correlations were used to obtain the convection velocity for the turbulent structures. This velocity ranged from 0.57 to 0.71 U(sub j).

DeBonis, James R.↗
NASA NTRS2011

Earth as an Extrasolar Planet: Earth Model Validation Using EPOXI Earth Observations

The EPOXI Discovery Mission of Opportunity reused the Deep Impact flyby spacecraft to obtain spatially and temporally resolved visible photometric and moderate resolution near-infrared (NIR) spectroscopic observations of Earth. These remote observations provide a rigorous validation of whole disk Earth model simulations used to better under- stand remotely detectable extrasolar planet characteristics. We have used these data to upgrade, correct, and validate the NASA Astrobiology Institute s Virtual Planetary Laboratory three-dimensional line-by-line, multiple-scattering spectral Earth model (Tinetti et al., 2006a,b). This comprehensive model now includes specular reflectance from the ocean and explicitly includes atmospheric effects such as Rayleigh scattering, gas absorption, and temperature structure. We have used this model to generate spatially and temporally resolved synthetic spectra and images of Earth for the dates of EPOXI observation. Model parameters were varied to yield an optimum fit to the data. We found that a minimum spatial resolution of approx.100 pixels on the visible disk, and four categories of water clouds, which were defined using observed cloud positions and optical thicknesses, were needed to yield acceptable fits. The validated model provides a simultaneous fit to the Earth s lightcurve, absolute brightness, and spectral data, with a root-mean-square error of typically less than 3% for the multiwavelength lightcurves, and residuals of approx.10% for the absolute brightness throughout the visible and NIR spectral range. We extend our validation into the mid-infrared by comparing the model to high spectral resolution observations of Earth from the Atmospheric Infrared Sounder, obtaining a fit with residuals of approx.7%, and temperature errors of less than 1K in the atmospheric window. For the purpose of understanding the observable characteristics of the distant Earth at arbitrary viewing geometry and observing cadence, our validated forward model can be used to simulate Earth s time dependent brightness and spectral properties for wavelengths from the far ultraviolet to the far infrared.brightness

Robinson, Tyler D.↗
DOE OSTI2020

Integrated Model of Models for Global Flood Alerting

A dramatic increase in frequency of minor to major flooding since 2000 has caused significant economic losses across the world. To mitigate and recover from these losses, actions have been taken to build resilient communities and infrastructures, specifically, by providing situational awareness in near real-time about flood impacts to enhance response and recovery efforts. Several hydrologic and hydraulic flood models are available at various spatial and temporal resolutions to forecast flood events at regional to global scale. Given the global coverage of two operational flood models – GloFAS (Global Flood Awareness System) and GFMS (Global Flood Monitoring System), the purpose of this project is to implement a Model of Models (MoM) approach to integrate the outputs from these two models to classify flood severity at watershed level worldwide, and send alerts based on severity similar to the USGS PAGER (used for severity alerting and impact analysis for earthquakes) to flood impacted communities. The alerts containing flood impacts and severity information will be disseminated through the DisasterAWARE platform, operated by the Pacific Disaster Center (PDC), that provides global multi-hazard alerting and Situational Awareness information to the emergency management community and public. The current version of the MoM approach was implemented for a case study flood event that occurred during January and February of 2020 in South and Central Africa. The findings of the case study event reveal that the approach is effective in identifying potential flood impact areas and the spatio-temporal variation of flood severity, flood depth and extent at watershed level, which will be used to assess infrastructure and societal impacts using earth-observation data and for alerting.

Kar, Bandana↗
DOE OSTI2023

Development of a molecularly informed biogeochemical framework for reactive transport modeling of subsurface carbon inventories, transformations and fluxes (Final Report)

The overall objective of the project was to combine new molecular-level characterization strategies with soil carbon flux measurements to develop and evaluate model representations of subsurface carbon cycling. We expanded on existing studies in the East River watershed, Colorado, in collaboration with the Berkeley Lab Watershed Function Scientific Focus Area (SFA), SLAC Groundwater Quality SFA, and Rocky Mountain Biological Laboratory (RMBL) to develop an elevation and vegetation gradient that is now the subject of long-term monitoring by the USGS. To achieve the overall objective, we combined field studies of soil respiration with laboratory analyses, ranging from spectroscopy to incubation studies. This combination of techniques enabled us to develop a new understanding of the drivers of high-elevation soil respiration. In the process, we developed three new modeling approaches that improve our ability to conceptualize and ultimately to represent soil respiration in numerical models. The first approach is a plot-scale transient inverse model that can be used to determine in situ CO 2 production rates from measured concentration profiles and surface fluxes. Application of this method revealed the importance of plant phenology and deep CO 2 production in moderating CO 2 fluxes to the atmosphere. The second modeling approach is a molecular-scale tool that enables spectroscopic and elemental data for carbon speciation to be transformed into functional group abundances, or the ‘SOC-fga model’. This method uniquely enables carbon speciation to be tracked within a reactive transport framework to partition carbon among different pathways and storage zones within the soil. The third modeling tool builds strongly on the previous approaches and captures the microbial processes driving heterotrophic respiration. This ‘dormancy model’ allows the native soil microbial population to respond transiently to the presence or absence of water in order to catalyze carbon respiration. This approach was also compared to the simpler and more widely used first-order model using two experimental datasets with different temporal and spatial resolutions. Our results illustrate that the simpler first order model provides a robust and efficient representation of deep (>1 meter) soil respiration, but that shallow soils, where most respiration occurs, require explicit representation of moisture-dependent activation and dormancy rates. By assessing soil organic carbon turnover at multiple scales, we see a complex array of controls emerge. Atte scale of a hillslope, spatial heterogeneity in soil respiration rates dominates and is uncorrelated with instantaneous soil moisture and plant community. At the profile scale, the balance between plant inputs and water availability is the dominant control. At the microbial to molecular scale, physiological processes associated with carbon use and carbon speciation are important controls. These scale-dependent controls emphasize the need for new modeling approaches that examine their interactions and hierarchies.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2023

Fine particulate concentrations over East Asia derived from aerosols measured by the Advanced Himawari Imager using machine learning

Fine particulate matter with a diameter below 2.5 μm (PM 2.5 ) is deleterious to the cardiovascular and respiratory systems. It is often difficult to assess the effects of PM 2.5 on human health over regions with limited ground monitoring sites, especially in East Asia. As an alternative, we estimated near-surface PM 2.5 concentrations by analyzing Advanced Himawari Imager (AHI) Yonsei Aerosol Retrieval (YAER) products. This study incorporates daytime data for East Asia covering the Korean Peninsula, China, Japan, Southeast Asia, and southern Mongolia. We collocated AHI YAER product pixels with meteorological, land-cover, and other ancillary data for the period from March 2018 to February 2019. To estimate PM 2.5 concentrations over wide areas spanning many countries displaying various relationships between aerosol optical depth and PM 2.5 , monthly models were developed by considering both the spatial and temporal characteristics of ground-based PM 2.5 measurements. Random forest machine learning model estimated ground-level mass concentrations of PM 2.5 ; subsequent 10-fold cross validation (CV) yielded a CV R 2 value of 0.81 and a CV root mean squared error (RMSE) of 12.3 μg m -3 . We investigated the spatial pattern of PM 2.5 concentrations over multiple countries and seasonal variation in PM 2.5 concentrations. Diurnal variation of a severe PM 2.5 event in the Korean Peninsula was investigated as a case study. The model captured the extremely heterogeneous spatial distribution of PM 2.5 concentrations peaked around local noon. To measure the capability of the developed model to estimate PM 2.5 concentrations in areas with few in-situ data, its predictive performance was evaluated using a dataset independent of the training process with an R 2 of 0.60 and RMSE of 8.18 μg m −3 . This study demonstrates the potential for satellite-based PM 2.5 estimation for areas with insufficient measuring stations.

Pm2.5↗
NASA NTRS2003

Observed and Modeled Trends in Southern Ocean Sea Ice

Conceptual models and global climate model (GCM) simulations have both indicated the likelihood of an enhanced sensitivity to climate change in the polar regions, derived from the positive feedbacks brought about by the polar abundance of snow and ice surfaces. Some models further indicate that the changes in the polar regions can have a significant impact globally. For instance, 37% of the temperature sensitivity to a doubling of atmospheric CO2 in simulations with the GCM of the Goddard Institute for Space Studies (GISS) is attributable exclusively to inclusion of sea ice variations in the model calculations. Both sea ice thickness and sea ice extent decrease markedly in the doubled CO, case, thereby allowing the ice feedbacks to occur. Stand-alone sea ice models have shown Southern Ocean hemispherically averaged winter ice-edge retreats of 1.4 deg latitude for each 1 K increase in atmospheric temperatures. Observations, however, show a much more varied Southern Ocean ice cover, both spatially and temporally, than many of the modeled expectations. In fact, the satellite passive-microwave record of Southern Ocean sea ice since late 1978 has revealed overall increases rather than decreases in ice extents, with ice extent trends on the order of 11,000 sq km/year. When broken down spatially, the positive trends are strongest in the Ross Sea, while the trends are negative in the Bellingshausen/Amundsen Seas. Greater spatial detail can be obtained by examining trends in the length of the sea ice season, and those trends show a coherent picture of shortening sea ice seasons throughout almost the entire Bellingshausen and Amundsen Seas to the west of the Antarctic Peninsula and in the far western Weddell Sea immediately to the east of the Peninsula, with lengthening sea ice seasons around much of the rest of the continent. This pattern corresponds well with the spatial pattern of temperature trends, as the Peninsula region is the one region in the Antarctic with a strong record of temperature increases. Still, although the patterns of the temperature and ice changes match fairly well, there is a substantial ways to go before these patterns are understood (and can be modeled) in the full context of global change.

Parkinson, Claire L.↗
NASA NTRS2011

Gas Generator Feedline Orifice Sizing Methodology: Effects of Unsteadiness and Non-Axisymmetric Flow

Engine LH2 and LO2 gas generator feed assemblies were modeled with computational fluid dynamics (CFD) methods at 100% rated power level, using on-center square- and round-edge orifices. The purpose of the orifices is to regulate the flow of fuel and oxidizer to the gas generator, enabling optimal power supply to the turbine and pump assemblies. The unsteady Reynolds-Averaged Navier-Stokes equations were solved on unstructured grids at second-order spatial and temporal accuracy. The LO2 model was validated against published experimental data and semi-empirical relationships for thin-plate orifices over a range of Reynolds numbers. Predictions for the LO2 square- and round-edge orifices precisely match experiment and semi-empirical formulas, despite complex feedline geometry whereby a portion of the flow from the engine main feedlines travels at a right-angle through a smaller-diameter pipe containing the orifice. Predictions for LH2 square- and round-edge orifice designs match experiment and semi-empirical formulas to varying degrees depending on the semi-empirical formula being evaluated. LO2 mass flow rate through the square-edge orifice is predicted to be 25 percent less than the flow rate budgeted in the original engine balance, which was subsequently modified. LH2 mass flow rate through the square-edge orifice is predicted to be 5 percent greater than the flow rate budgeted in the engine balance. Since CFD predictions for LO2 and LH2 square-edge orifice pressure loss coefficients, K, both agree with published data, the equation for K has been used to define a procedure for orifice sizing.

Rothermel, Jeffry↗
DOE OSTI2025

Investigation of Main Bearing Fatigue Estimate Sensitivity to Synthetic Turbulence Models Using a Novel Drivetrain Model Implemented in OpenFAST

ABSTRACT A coupled medium‐fidelity drivetrain model is developed and implemented in OpenFAST for a 10‐MW land‐based reference turbine. The implementation is verified against a fully coupled multibody wind turbine model, including a detailed drivetrain. The new model can simultaneously and accurately estimate main bearing loads and represent elastic bending of the drivetrain. It has low computational cost and is useful for early design phases, sensitivity analyses and complex systems like wind farms (where computational expense must be expended elsewhere). Here, the model is implemented for a monopile offshore wind turbine and used to investigate the sensitivity of main bearing basic rating life to different synthetic turbulence models. Large‐eddy simulations (LES) targeting stable, neutral, and unstable atmospheric conditions at below‐, near‐ and above‐rated wind speeds are used as a reference. The turbulence models recommended by the International Electrotechnical Commission, the Mann spectral tensor model, and the Kaimal spectral model with exponential coherence are fitted to the LES data. Additionally, a constrained turbulence generator, PyConTurb (short for Python Constrained Turbulence ), based on LES data, is applied in the aero‐hydro‐servo‐elastic simulations. Taking PyConTurb as the baseline, the Kaimal model significantly underestimates fatigue of the downwind main bearing, with between 10% and 40% less damage. The Mann model also underestimates the downwind main bearing fatigue by up to 30%. The upwind main bearing damage is driven by mean loads, and differences between models are less significant, although the trends are similar. Reasons for these discrepancies are investigated and attributed to differences in spatial and temporal variations among the turbulence models.

17 WIND ENERGY↗
NASA NTRS2017

Monitoring Land Surface Albedo and Vegetation Dynamics Using High Spatial and Temporal Resolution Synthetic Time Series from Landsat and the MODIS BRDF/NBAR/Albedo Product

Seasonal vegetation phenology can significantly alter surface albedo which in turn affects the global energy balance and the albedo warmingcooling feedbacks that impact climate change. To monitor and quantify the surface dynamics of heterogeneous landscapes, high temporal and spatial resolution synthetic time series of albedo and the enhanced vegetation index (EVI) were generated from the 500-meter Moderate Resolution Imaging Spectroradiometer (MODIS) operational Collection V006 daily BRDF (Bidirectional Reflectance Distribution Function) / NBAR (Nadir BRDF-Adjusted Reflectance) / albedo products and 30-meter Landsat 5 albedo and near-nadir reflectance data through the use of the Spatial and Temporal Adaptive Reflectance Fusion Model (STARFM). The traditional Landsat Albedo (Shuai et al., 2011) makes use of the MODIS BRDFAlbedo products (MCD43) by assigning appropriate BRDFs from coincident MODIS products to each Landsat image to generate a 30-meter Landsat albedo product for that acquisition date. The available cloud free Landsat 5 albedos (due to clouds, generated every 16 days at best) were used in conjunction with the daily MODIS albedos to determine the appropriate 30-meter albedos for the intervening daily time steps in this study. These enhanced daily 30-meter spatial resolution synthetic time series were then used to track albedo and vegetation phenology dynamics over three Ameriflux tower sites (Harvard Forest in 2007, Santa Rita in 2011 and Walker Branch in 2005). These Ameriflux sites were chosen as they are all quite nearby new towers coming on line for the National Ecological Observatory Network (NEON), and thus represent locations which will be served by spatially paired albedo measures in the near future. The availability of data from the NEON towers will greatly expand the sources of tower albedometer data available for evaluation of satellite products. At these three Ameriflux tower sites the synthetic time series of broadband shortwave albedos were evaluated using the tower albedo measurements with a Root Mean Square Error (RMSE) less than 0.013 and a bias within the range of 0.006. These synthetic time series provide much greater spatial detail than the 500 meter gridded MODIS data, especially over more heterogeneous surfaces, which improves the efforts to characterize and monitor the spatial variation across species and communities. The mean of the difference between maximum and minimum synthetic time series of albedo within the MODIS pixels over a subset of satellite data of Harvard Forest (16 kilometers by 14 kilometers) was as high as 0.2 during the snow-covered period and reduced to around 0.1 during the snow-free period. Similarly, we have used STARFM to also couple MODIS Nadir BRDF-Adjusted Reflectances (NBAR) values with Landsat 5 reflectances to generate daily synthetic times series of NBAR and thus Enhanced Vegetation Index (NBAR-EVI) at a 30-meter resolution. While normally STARFM is used with directional reflectances, the use of the view angle corrected daily MODIS NBAR values will provide more consistent time series. These synthetic times series of EVI are shown to capture seasonal vegetation dynamics with finer spatial and temporal details, especially over heterogeneous land surfaces.

Vegetation Index↗
DOE OSTI2021

Predicting Nugget Size of Resistance Spot Welds Using Infrared Thermal Videos With Image Segmentation and Convolutional Neural Network

Resistance spot welding (RSW) is a widely adopted joining technique in automotive industry. Recent advancement in sensing technology makes it possible to collect thermal videos of the weld nugget during RSW using an infrared (IR) camera. The effective and timely analysis of such thermal videos has the potential of enabling in situ nondestructive evaluation (NDE) of the weld nugget by predicting nugget thickness and diameter. Deep learning (DL) has demonstrated to be effective in analyzing imaging data in many applications. However, the thermal videos in RSW present unique data-level challenges that compromise the effectiveness of most pre-trained DL models. We propose a novel image segmentation method for handling the RSW thermal videos to improve the prediction performance of DL models in RSW. The proposed method transforms raw thermal videos into spatial-temporal instances in four steps: video-wise normalization, removal of uninformative images, watershed segmentation, and spatial-temporal instance construction. The extracted spatial-temporal instances serve as the input data for training a DL-based NDE model. The proposed method is able to extract high-quality data with spatial-temporal correlations in the thermal videos, while being robust to the impact of unknown surface emissivity. Overall, our case studies demonstrate that the proposed method achieves better prediction of nugget thickness and diameter than predicting without the transformation.

42 ENGINEERING↗
DOE OSTI2022

Snow Albedo Feedbacks Enhance Snow Impurity-Induced Radiative Forcing in the Sierra Nevada

This study employs a fully coupled meteorology-chemistry-snow model to investigate the impacts of light-absorbing particles (LAPs) on snow darkening in the Sierra Nevada. After comprehensive evaluation with spatially and temporally complete satellite retrievals, the model shows that LAPs in snow reduce snow albedo by 0.013 (0-0.045) in the Sierra Nevada during the ablation season (April-July), producing a midday mean radiative forcing (RF) of 4.5 W m -2 which increases to 15-22 W m -2 in July. LAPs in snow accelerate snow aging processes and reduce snow cover fraction, which doubles the albedo change and radiative forcing caused by LAPs. The impurity-induced snow darkening effects decrease snow water equivalent and snow depth by 20 mm and 70 mm in June in Sierra Nevada bighorn sheep habitat. The earlier snowmelt reduces root zone soil moisture by 20%, deteriorating the forage productivity and playing a negative role in the survival of bighorn sheep.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Effects of Cloud Liquid-Phase Microphysical Processes in Mixed-Phase Cumuli Over the Tibetan Plateau

Numerical simulations often overpredict precipitation over the Tibetan Plateau (TP). To examine the factors causing precipitation overprediction, different parameterizations of liquid-phase microphysical processes (accretion, autoconversion, and entrainment-mixing) are implemented into the Morrison microphysics scheme to simulate a TP precipitation event in summer with the Weather Research and Forecasting (WRF) model. The general spatial distribution and temporal trend of precipitation are captured by all simulations, but the precipitation rate is overpredicted. The results from sensitivity experiments suggest that compared to other examined liquid-phase processes, the accretion process is more important in precipitation simulation over the TP region. Further investigation with the Heidke skill scores reveals that accretion parameterization that takes into account the raindrop size produces the most accurate results in terms of the total surface precipitation. This parameterization suppresses spurious accretion and does not produce liquid-phase precipitation until cloud droplets are big enough. Here, it is also confirmed that increasing the model resolution can reduce precipitation overprediction. Results from the case study are confirmed by the use of a one-month simulation.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1988

Characterizing forest ecosystem dynamics through modelling and remote sensing observations

To gain a better understanding of northern/boreal forest dynamics over a range of spatial and temporal scales, an approach to integrate models of forest growth, soil processes and radiative transfer with remote sensing observations was developed. The integrated model and remote sensing can be used to examine descriptors of ecosystem dynamics. To examine the scaling of vegetation pattern from the local to the regional domain, distributions of area and perimeters of vegetation community associations were determined from satellite and aircraft images. Relationships between computed fractal dimensions (1.5 to 1.8) and succession history for managed and unmanaged areas are being explored.

Ranson, K. J.↗
NASA NTRS1975

Auroral zone microbursts, substructures, and a model for microburst precipitation

The spatial and temporal characteristics of X-ray microbursts detected by collimated directional telescopes have been analyzed in detail. Results indicate the presence of a persistent periodicity of about 0.5 second and 1.2 seconds, respectively. In one event, microbursts exhibit fine structures similar to those observed by Lampton (1967). These substructures are poorly correlated in both space and time as indicated by the low correlation coefficients obtained in auto- and cross-correlation analyses between various pairs of telescopes. The source dimension of these substructures is deduced to be less than 18 km at ionospheric heights. By considering that microburst electrons are near regions of strong diffusion, we show that microburst precipitation can be generated if electric field turbulence is present in the magnetosphere. We argue that electrons of about 50 keV in bounce resonance with a parallel electric field of about 1 millivolt/meter at about 1 Hz can account for the microburst period as well as the precipitation lifetime of about 0.2 second.

Parks, G. K.↗
NASA NTRS2009

Spatial and Temporal Extrapolation of Disdrometer Size Distributions Based on a Lagrangian Trajectory Model of Falling Rain

Methodologies to improve disdrometer processing, loosely based on mathematical techniques common to the field of particle flow and fluid mechanics, are examined and tested. The inclusion of advection and vertical wind field estimates appear to produce significantly improved results in a Lagrangian hydrometeor trajectory model, in spite of very strict assumptions of noninteracting hydrometeors, constant vertical air velocity, and time independent advection during the scan time interval. Wind field data can be extracted from each radar elevation scan by plotting and analyzing reflectivity contours over the disdrometer site and by collecting the radar radial velocity data to obtain estimates of advection. Specific regions of disdrometer spectra (drop size versus time) often exhibit strong gravitational sorting signatures, from which estimates of vertical velocity can be extracted. These independent wind field estimates become inputs and initial conditions to the Lagrangian trajectory simulation of falling hydrometeors.

Lane, John E.↗
NASA NTRS2021

Variabilities in Pm2.5 and Black Carbon Surface Concentrations Reproduced by Aerosol Optical Properties Estimated by In-Situ Data, Ground Based Remote Sensing and Modeling

Because of the increased temporal and spatial resolutions of the sensors onboard recently launched satellites, satellite-based surface aerosol concentration, which is usually estimated from the aerosol optical depth (AOD), is expected to become a strategic tool for air quality studies in the future. By further exploring the relationships of aerosol concentrations and their optical properties using ground observations, the accuracies of these products can be improved. Here, we analyzed collocated observations of surface mass concentrations of fine particulate matter (PM2.5) and black carbon (BC), as well as columnar aerosol optical properties from a sky radiometer and aerosol extinction profiles obtained by multi-axis differential optical absorption spectroscopy (MAX-DOAS), during the 2019–2020 period. We focused the analyses on a daily scale, emphasizing the role of the ultraviolet (UV) spectral region. Generally, the correlation between the AOD of the fine fraction (i.e., fAOD) and the PM2.5 surface concentration was moderately strong, regardless of considerations of boundary layer humidity and altitude. In contrast, the fAOD of the partial column below 1 km, which was obtained by combining sky radiometer and MAX-DOAS retrievals, better reproduced the variability of the PM2.5 and resulted in a linear relationship. In the same manner, we demonstrated that the absorption AOD of the fine fraction (fAAOD) of the partial column was related to the variability of the BC concentration. Analogous analyses based on aerosol products from the Modern-Era Retrospective analysis for Research and Applications, Version 2 (MERRA-2) confirmed these findings and highlighted the importance of the shape of the aerosol profile. Overall, our results indicated a remarkable consistency among the retrieved datasets, and between the datasets and MERRA-2 products. These results confirmed the well-known sensitivity to aerosol absorption in the UV spectral region; they also highlighted the efficacy of combined MAX-DOAS and sky radiometer observations.

Alessandro Damiani↗
NASA NTRSDate not supplied

Wake Vortex Interaction of Urban Air Mobility Aircraft

This paper presents a study of wake vortex interaction modeling for urban air mobility. Wake vortex modeling approaches for fixed-wing aircraft and rotorcraft are investigated. A wake age model is developed that accounts for the temporal and spatial dissipation of the wake-induced downwash. A wake vortex model is developed for rotorcraft that accounts for blade flapping motion and cyclic pitch control to reduce the lift asymmetry. This in turn results in an equal lift circulation strength on the advancing side and retreating side of the rotor. Two wake vortex interaction simulations are performed to illustrate the modeling approaches.

Wake Vortex↗