Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SWELLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Characterization of high thermal conductivity fuel surrogates before and after ion irradiation

High thermal conductivity nuclear fuels offer important potential advantages over traditional oxide-based fuels such as higher burnup, reduction in fission gas release, and better overall safety of the system. One proposed approach to high thermal conductivity fuels utilizes high thermal conductivity nonfissile additives with UO 2 fuel to lower the fuel operating temperature and thereby take advantage of the highly favorable radiation resistance of UO 2 at lower operating temperatures. However, differential swelling in the matrix and high conductivity additive phases during high dose irradiation could lead to internal cracking and poor performance. In the current study, ceria (CeO 2 ) and zirconia (ZrO 2 ) surrogate matrices were used to model UO2 behavior. Additives of 10 vol. % Al 2 O 3 or SiC in the form of short fibers or platelets were used for the high conductivity second phase. The nuclear fuel surrogates were sintered to achieve densities greater than 93% of the ideal values. Scanning electron microscopy (SEM) imaging and X-ray diffraction confirmed the uniform distribution of the second phase and that no intermetallic second phase was formed during sintering. The thermal conductivity of the sintered samples was measured from 50 °C to 900 °C and confirmed the desirable increase compared to pure CeO 2 /ZrO 2 pellets. Samples were irradiated with 20 MeV Ni 6+ ions at midrange doses ranging from 1 to 15 displacements per atom (dpa) and temperatures from 300 °C to 700 °C. Post irradiation characterization revealed a good stability of the samples at low to medium doses with matrix lattice parameter swelling of < 0.14 % but showed a significant microstructural deterioration and decrease of the mechanical properties at 15 dpa.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Interpreting experimental measurements of helium bubbles using stochastic cluster dynamics models of heterogeneous nucleation and growth in irradiated ferritic alloys

Among a number of other advantageous features, ferritic/martensitic steels are being considered as fusion reactor structural materials due to their low intrinsic swelling under irradiation. However, under high-energy neutron irradiation, He produced through (n, α) reactions stabilizes vacancy clusters, which then act as seeds for bubble formation and growth, negating the intrinsic swelling resistance of these alloys. Standard models of irradiation damage accumulation and microstructural evolution consider homogeneous nucleation as the basis for bubble formation and growth. However, this generally does not explain the large bubble densities and sizes observed experimentally under a number of different conditions. Here, we propose a more realistic physical model of bubble nucleation, formation, and growth designed to capture recent experimental measurements of He-bubble formation and evolution during co-implantation of He and Fe ions in model ferritic alloys. We find that experimental results are explained only when the following three features are considered simultaneously: (i) heterogeneous nucleation of He-vacancy bubbles at defect sinks (e.g., dislocations, grain boundaries, and second-phase precipitates), (ii) nucleation and growth of bubbles via the ‘trap mutation’ mechanism (i.e., spontaneous production of Frenkel pairs due to absorption of He atoms), and (iii) transition from a growth-limited, He-stabilized bubble regime to a ‘runaway’ void-type growth scenario. The model is implemented into a stochastic cluster dynamics framework that takes advantage of cluster size grouping methods to accelerate the simulations, allowing us to reach 10 dpa of simulated irradiated dose, and to capture cluster sizes in excess of 20 nm. Further, a careful extrapolation exercise conducted assuming classical nucleation theory leads to excellent agreement with the experimental measurements at 50 dpa of irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermo-mechanical deterioration and molecular degradation of 3D-printed methacrylate-based polymer in various chemical environments

The advancement of additive manufacturing (AM) has accelerated the development of stereolithographic (SLA) photo-curable resins, particularly methacrylate-based polymers, due to the ability to their high-resolution, robust mechanical properties, and suitability. However, their long-term performance in chemical environments remains poorly understood. This study investigates the extent and mechanisms of degradation on an SLA-printed methacrylate-based polymer subjected to various chemicals, including polar and non-polar solvents, as well as strongly acidic aqueous solutions over a 12-week accelerated aging period. A comprehensive analytical approach incorporating swelling kinetics, surface morphology, tensile and dynamic mechanical analysis (DMA), Fourier-transform infrared (FTIR) spectroscopy, and mass spectrometry (MS) was employed to characterize chemical absorption, structural integrity, and leached products. Results reveal that degradation severity is governed by both the polarity and reactivity of the chemical environment. Notably, exposure to 6 mol L -1 HNO₃ induced the most severe deterioration, with over threefold higher swelling compared to other media, and significant reductions in tensile strength, tensile modulus, and glass transition temperature (T g ). In contrast, specimens aged in non-polar solvents (xylene and dodecane) exhibited negligible chemical interaction and retained mechanical performance. FTIR and MS analyses identified acid-catalyzed hydrolysis of ester groups as prominent degradation pathways in acidic media, while diffusion-controlled plasticization prevailed in polar solvents. Furthermore, this study provides valuable insights into the chemical stability of SLA-printed polymers and develops predictive degradation profiles that are crucial for designing durable polymer systems for advanced industrial use.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Characterizing and modeling the mechanical behavior of an anion exchange membrane for carbon capture applications

A new direct air capture (DAC) technology uses a moisture swing (MS) process with anion exchange membranes, potentially offering a more energy-efficient way to remove CO₂ from the air. In this MS process, the membrane absorbs CO₂ as it dries and releases it when water is added. Understanding the mechanical behavior of these membranes is essential for improving the design and efficiency of DAC systems and prolonging sorbent lifetime. This study tested one anion exchange membrane, Fumasep’s FAA-3, under mechanical loading and various temperature and humidity conditions to measure its swelling, stiffness, strength, plastic deformation, and stress relaxation. Experimental results were used to identify a mechanical model for FAA-3 that can be used to predict the material’s nonlinear viscous behavior under various loads and environments. Unlike prior studies that assumed linear elastic behavior, this work incorporates humidity-dependent swelling, thermal expansion, and nonlinear viscoelasticity of FAA-3 in both the experiments and the model.

Direct air capture↗
DOE OSTI2024

Development of a MOOSE-based crystal plasticity model with irradiation defect evolution for irradiation creep in 316

Irradiation creep and irradiation swelling are two of the lifetime limiting factors for structural materials in nuclear reactors. These mechanical effects are driven by irradiation defect evolution and the interaction of those defects with dislocations in the microstructure. We present here a coupled cluster dynamics – crystal plasticity approach to model irradiation swelling and creep behavior in 316 SS. The time-dependent evolution of irradiation defects is calculated with a cluster dynamics approach and passed to the crystal plasticity model to compute the dislocation evolution. We show the impact of the irradiation defect evolution on the stress state in the material, which drives inelastic deformation through dislocation motion. The inelastic deformation in the 316 SS is dependent on the dose rate, where the inelastic deformation driven by the early-stage irradiation defect evolution determines the mechanical behavior of the 316 SS.

316 Stainless Steels↗
DOE OSTI2026

Dynamic Evaluation of the Upper Tyler Formation and Well Stimulation Fluid Interactions Using Micro-CT Imaging

Abundant concentrations of swelling clays in the oil-bearing upper Tyler Formation inhibit unconventional well stimulation techniques and associated long-term oil and gas production success. Laboratory evaluation of the geochemical interactions between the formation material and various stimulation fluids may help identify innovative approaches that provide a solution to successful well stimulation and subsequent oil production. The objective of this research was to understand the complexities of well stimulation fluid and clay mineral interactions within the Tyler Formation and identify potential fracturing fluid formulations that mitigate swelling properties of the clays in the reservoir to enhance stimulation success and promote long-term oil and gas production. Collaboration with the National Energy Technology Laboratory (NETL), utilizing their Tescan DynaTOM micro-CT analysis instrumentation, provided an innovative approach to understand real-time, dynamic interactions of the formation material and various potential stimulation fluids. Results are anticipated to identify key mechanisms occurring at the micro-scale level and provide insight into modified stimulation techniques uniquely suited for successful production applications.

enhanced oil recovery↗
DOE OSTI2020

Experimental Investigation of Inhibitive Drilling Fluids Performance: Case Studies from United States Shale Basins

Shale formations are attractive prospects due to their potential in oil and gas production. Some of the largest shale formations in the mainland US, such as the Tuscaloosa Marine Shale (TMS), have reserves estimated to be around 7 billion barrels. Despite their huge potential, shale formations present major concerns for drilling operators. These prospects have unique challenges because of all their alteration and incompatibility issues with drilling and completion fluids. Most shale formations undergo numerous chemical and physical alterations, making their interaction with the drilling and completion fluid systems very complex to understand. In this study, a high-pressure, high-temperature (HPHT) drilling simulator was used to mimic real time drilling operations to investigate the performance of inhibitive drilling fluid systems in two major shale formations (Eagle Ford Shale and Tuscaloosa Marine Shale). A series of drilling experiments using the drilling simulator and clay swelling tests were conducted to evaluate the drilling performance of the KCl drilling fluid and cesium formate brine systems and their effectiveness in minimizing drilling concerns. Cylindrical cores were used to mimic vertical wellbores. It was found that the inhibitive muds systems (KCl and cesium formate) provided improved drilling performance compared to conventional fluid systems. Among the inhibitive systems, the cesium formate brine showed the best drilling performances due to its low swelling rate and improved drilling performance.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2024

The Role of Side Chains and Hydration on Mixed Charge Transport in n ‐Type Polymer Films

Abstract Introducing ethylene glycol (EG) side chains to a conjugated polymer backbone is a well‐established synthetic strategy for designing organic mixed ion‐electron conductors (OMIECs). However, the impact that film swelling has on mixed conduction properties has yet to be scoped, particularly for electron‐transporting (n‐type) OMIECs. Here, the authors investigate the effect of the length of branched EG chains on mixed charge transport ofn‐type OMIECs based on a naphthalene‐1,4,5,8‐tetracarboxylic‐diimide‐bithiophene backbone. Atomic force microscopy (AFM), grazing‐incidence wide‐angle X‐ray scattering (GIWAXS), and scanning tunneling microscopy (STM) are used to establish the similarities between the common‐backbone films in dry conditions. Electrochemical quartz crystal microbalance with dissipation monitoring (EQCM‐D) and in situ GIWAXS measurements reveal stark changes in film swelling properties and microstructure during electrochemical doping, depending on the side chain length. It is found that even in the loss of the crystallite content upon contact with the aqueous electrolyte, the films can effectively transport charges and that it is rather the high water content that harms the electronic interconnectivity within the OMIEC films. These results highlight the importance of controlling water uptake in the films to impede charge transport inn‐type electrochemical devices.

Chemistry↗
DOE OSTI2025

Solid‐State Prealkylation of Electrode Architectures (SPEAR): Direct Control of Prelithiation Levels in Silicon Anodes and Electrochemical Cycling

The Solid-state Prealkylation of Electrode ARchitectures (SPEAR) is different than traditional electrochemical prealkylation processes. Through SPEAR, alkylation is driven by solid-state diffusion without the simultaneous SEI formation concomitant with polarization. Here, we investigate the prelithiation of 80 wt. % Si-based anodes to varying amounts (up to Li 1.38 Si) to understand the trade-off between improved Li capacity and expansion-induced stress. Through dilatometry, we found that solid-state lithiation led to filling of the electrode pores through silicon expansion. This swelling changed the SEI formation process and accessibility of the silicon compared to an electrochemically lithiated electrode. Indeed, optimal prelithiation to Li 0.82 Si increases the initial C/3 cycling capacity post-SEI formation up to 43%, consistent with deeper Si activation through the electrode bulk. Prelithiation and cycling cells prelithiated beyond Li 0.82 Si results in a state of charge (SOC) close to 100% which facilitates parasitic degradation mechanisms and volume expansion of the Si electrode. The results demonstrate a pathway to modify silicon activation/SEI formation to enable high-energy electrodes.

Musgrove, Amanda L. [Oak Ridge National Laboratory↗
DOE OSTI2022

Bioinspired Macrocyclic Molecule Supported Two‐Dimensional Lamellar Membrane with Robust Interlayer Structure for High‐Efficiency Nanofiltration

Abstract 2D lamellar membranes (2DLMs) are used for efficient desalination and nanofiltration. However, weak interactions between adjacent stacked nanosheets result in susceptibility to swelling that limits practical applicability. Inspired by the super adhesion of multi‐point suction cups on octopus tentacles, a 2DLM is constructed from Ti 3 C 2 T x MXene supported by the macrocyclic “multi‐point” molecule cucurbit[5]uril (CB5) and demonstrated for nanofiltration of methyl blue (MB) and enrichment of uranyl carbonate. Experimental results and density functional theory calculations indicate that CB5 rivets to the surface of the nanoflakes through strong stable interactions between its multiple binding sites and surface hydroxyl functional groups on MXene nanosheets. This novel 2DLM exhibits excellent nanofiltration performance (69 L m −2 h −1 bar −1 permeance with 93.6% rejection for MB) and can be recycled at least 30 times without significant degradation. The 2DLM exhibits excellent swelling resistance at high salinity, with a demonstration of selective enrichment of uranyl carbonate from artificial water and natural seawater. The results provide a new strategy for constructing highly stable 2DLMs with interlayer spacing controllable from sub‐nano to nanometer scales, for size‐selective sieving of molecules and ions, high‐efficiency nanofiltration, and other applications.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Network Polymer Properties Engineered Through Polymer Backbone Dispersity and Structure

Abstract Dispersity ( Ð or M w /M n ) is an important parameter in material design and as such can significantly impact the properties of polymers. Here, polymer networks with independent control over the molecular weight and dispersity of the linear chains that form the material are developed. Using a RAFT polymerization approach, a library of polymers with dispersity ranging from 1.2—1.9 for backbone chain‐length (DP) 100, and 1.4—3.1 for backbone chain‐length 200 were developed and transformed to networks through post‐polymerization crosslinking to form disulfide linkers. The tensile, swelling, and adhesive properties were explored, finding that both at DP 100 and DP 200 the swelling ratio, tensile strength, and extensibility were superior at intermediate dispersity (1.3—1.5 for DP 100 and 1.6—2.1 for DP 200) compared to materials with either substantially higher or lower dispersity. Furthermore, adhesive properties for materials with chains of intermediate dispersity at DP 200 revealed enhanced performance compared to the very low or high dispersity chains.

Raji, Ibrahim O.↗
DOE OSTI2024

The Influence of Alkyl Spacers and Molecular Weight on the Charge Transport and Storage Properties of Oxy‐Bithiophene‐Based Conjugated Polymers

Abstract Conjugated polymers (CPs) with polar side chains can conduct electronic and ionic charges simultaneously, making them promising for bioelectronics, electrocatalysis and energy storage. Recent work showed that adding alkyl spacers between CP backbones and polar side chains improved electronic charge carrier mobility, reduced swelling and enhanced stability, without compromising ion transport. However, how alkyl spacers impact polymer backbone conformation and, subsequently, electronic properties remain unclear. In this work, we design two oxy‐bithiophene‐based CP series, each featuring progressively extended alkyl spacer lengths and two distinct molecular weight (MW) distributions. Using operando characterisations, we evaluate the (spectro)electrochemical and swelling properties of the polymer thin films, and their performance in organic field‐effect transistors and organic electrochemical transistors. Surprisingly, alkyl spacers negatively impact the hole mobility of our polymers, with higher MW amplifying this effect. Using molecular dynamics simulations, we show that it is thermodynamically favourable for adjacent non‐polar alkyl spacers to aggregate in polar electrolytes, leading to backbone twisting. Further spectroscopic measurements corroborate this prediction. Our findings demonstrate the active interactions between side chain structure, MW and electrolyte/solvent polarity in influencing polymer performance, underscoring the importance of considering solvation environment effects on polymer conformation when designing new mixed conducting CPs for electrochemical applications.

Yu, Hang [Department of Physics and Centre for Pro↗
DOE OSTI2024

Network Polymer Properties Engineered Through Polymer Backbone Dispersity and Structure

Abstract Dispersity ( Ð or M w /M n ) is an important parameter in material design and as such can significantly impact the properties of polymers. Here, polymer networks with independent control over the molecular weight and dispersity of the linear chains that form the material are developed. Using a RAFT polymerization approach, a library of polymers with dispersity ranging from 1.2—1.9 for backbone chain‐length (DP) 100, and 1.4—3.1 for backbone chain‐length 200 were developed and transformed to networks through post‐polymerization crosslinking to form disulfide linkers. The tensile, swelling, and adhesive properties were explored, finding that both at DP 100 and DP 200 the swelling ratio, tensile strength, and extensibility were superior at intermediate dispersity (1.3—1.5 for DP 100 and 1.6—2.1 for DP 200) compared to materials with either substantially higher or lower dispersity. Furthermore, adhesive properties for materials with chains of intermediate dispersity at DP 200 revealed enhanced performance compared to the very low or high dispersity chains.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Influence of Alkyl Spacers and Molecular Weight on the Charge Transport and Storage Properties of Oxy‐Bithiophene‐Based Conjugated Polymers

Conjugated polymers (CPs) with polar side chains can conduct electronic and ionic charges simultaneously, making them promising for bioelectronics, electrocatalysis and energy storage. Recent work showed that adding alkyl spacers between CP backbones and polar side chains improved electronic charge carrier mobility, reduced swelling and enhanced stability, without compromising ion transport. However, how alkyl spacers impact polymer backbone conformation and, subsequently, electronic properties remain unclear. In this work, we design two oxy-bithiophene-based CP series, each featuring progressively extended alkyl spacer lengths and two distinct molecular weight (MW) distributions. Using operando characterisations, we evaluate the (spectro)electrochemical and swelling properties of the polymer thin films, and their performance in organic field-effect transistors and organic electrochemical transistors. Surprisingly, alkyl spacers negatively impact the hole mobility of our polymers, with higher MW amplifying this effect. Using molecular dynamics simulations, we show that it is thermodynamically favourable for adjacent non-polar alkyl spacers to aggregate in polar electrolytes, leading to backbone twisting. Further spectroscopic measurements corroborate this prediction. Our findings demonstrate the active interactions between side chain structure, MW and electrolyte/solvent polarity in influencing polymer performance, underscoring the importance of considering solvation environment effects on polymer conformation when designing new mixed conducting CPs for electrochemical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Preparation of pH ‐responsive cellulose nanofibril/sodium alginate based hydrogels for drug release

Abstract In this work, hydrogels composed of cellulose nanofibril (CNF) and sodium alginate (SA) were prepared as a pH‐responsive release system by controlling the amount of CNF and SA. Scanning electron microscopy, thermogravimetric analysis, and swelling rate methods were used to characterize. The results showed that when the mass ratio of CNF to SA was 2:1, CNF/SA hydrogels with better morphology were obtained. Due to the deprotonation or protonation of calcium alginate, as the pH changing from 1.5 to 11.0, the swelling ratio increased from 7 times to 19 times compared with its dry weight. The drug release behaviors of the CNF/SA hydrogels using ibuprofen (IBU) as a model drug were investigated in vitro. The release of IBU was faster in alkaline conditions and slower in acidic conditions. The drug release mechanism under pH stimulation could be interpreted by the Fickian diffusion and erosion effect based on Korsmeyer‐Peppas model.

Li, Yuhang↗
DOE OSTI2021

Toward predictive permeabilities: Experimental measurements and multiscale simulation of methanol transport in Nafion

A polymer membrane's permeability to solutes determines its suitability for various applications: a permeability value is essential for predicting performance in diverse contexts. Using aqueous methanol permeation through Nafion as an example, we describe a methodology for determining membrane permeability that accounts for boundary layer effects and the possibility of swelling. For the materials and apparatus used herein, analysis of a permeance measurement and computational fluid dynamics simulations show that the mass transfer boundary layer is on the order of ones to tens of microns. Additionally, the data are used to develop and validate a multiscale model describing solute permeation through a hydrated membrane as a series of physical mechanistic steps: reversible adsorption from solution at the membrane interface, diffusion driven by a concentration gradient within the membrane, and reversible desorption into solution at the opposite membrane interface. The validated model is used to predict methanol transport across a solar-driven CO 2 reduction device and to assess the impact of polymer changes on the measured value. The approach of combining experimental data, computational fluid dynamics, and the mechanistic multiscale model is expected to provide more accurate analysis of membrane permeation data in cases with polymer swelling or unusual device geometries, among others.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗