Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SURFACE ROUGHNESS EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Multifrequency measurements of the effects of soil moisture, soil texture, and surface roughness

An experiment on remote sensing of soil moisture content was conducted over bare fields with microwave radiometers at the frequencies of 1.4, 5, and 10.7 GHz, during July-September of 1981. Three bare fields with different surface roughnesses and soil textures were prepared for the experiment. The experimental results show that the effect of surface roughness is to increase the soil's brightness temperature and to reduce the slope of regression between brightness temperature and moisture content. The slopes of regression for soils with different textures are found to be comparable and the effect of soil texture is reflected in the difference of regression line intercepts at brightness-temperature axis. Measurements on wet smooth bare fields give lower brightness temperatures at 5 than at 1.4 GHz. This phenomenon is not expected from current radiative transfer theory, using laboratory measurements of the relationship between permittivity and moisture content for different soil-water mixtures at frequencies of not greater than 5 GHz.

Wang, J. R.↗
NASA NTRS1987

Backscatter from a periodic rough surface at near grazing incidence

The effect of periodic surface roughness on the radar cross section (RCS) was studied. The surface roughness was formed by a small sinusoidal variation in a planar surface. RCS measurements were obtained for two different sinusoidal variations near grazing incidence for both principle polarizations. Significant grating lobes were observed in the measurements which directly correspond to the roughness characteristics. A physical optics solution was generated and compared to the measurements with reasonable agreement.

Dominek, A. K.↗
NASA NTRS1986

Preliminary evaluation of the SIR-B response to soil moisture, surface roughness, and crop canopy cover

Two predawn ascending data-takes by the Shuttle Imaging Radar-B (SIR-B) were used to evaluate the effects of surface roughness, crop canopy, and soil moisture on radar backscatter. The two images, separated by three days, were both obtained at 30-deg local angle of incidence, but with opposite azimuth viewing directions. The imagery was externally calibrated with respect to the radar backscattering coefficient sigma(0) via response to arrays of point and area-extended targets of known radar cross section. Three land-cover classes: (1) corn, (2) corn stubble and plowed bare soil, and (3) disked bare soil, soybeans, soybean stubble, alfalfa, and clover could be readily separated for either observation date on the basis of image tone alone. The dependence of sigma(0) on the surface roughness and canopy brightness inhibits the capability of SIR to globally estimate the near-surface soil moisture from the value of sigma(0) for single date observations, unless the surface roughness or canopy cover conditions are accounted for. However, within given ranges of these conditions, the sigma(0) was found to be highly correlated with the soil moisture.

Dobson, M. C.↗
NASA NTRS2019

The Effect of Stainless Steel 304 Surface Roughness on Ice Adhesion Shear Strength of Accreted Impact Ice

Aircraft in-flight icing is problematic due to the ad-verse effect on vehicle performance. It occurs when supercooled water droplets (SCWD) present in clouds, under the appropriate environmental conditions, col-lide with the aircraft surface resulting in accretion of ice (i.e., impact icing). Impact ice can range from clear/glaze to rime or a combination of the two (i.e., mixed) with the type determined by the air temperature (0 to -20°C), liquid water content (LWC, 0.3-0.6 g/cu.m), and droplet size [median volumetric diameter (MVD) of 15-40 µm] present during accretion.1 These impact icing events generally occur at temperatures ranging from 0 to -20°C. Below -20°C, ice crystals dominate the environment and typically do not adhere to the aircraft surface. A main difference between an impact icing occurrence and a slow growth icing (i.e., freezer ice) one is the speed of the icing event. Besides environmental conditions, ice adhesion strength (IAS) to a metallic substrate depends upon surface roughness. It is known that increasing surface roughness and decreasing temperature lead to in-creases in IAS.

Smith, Joseph G., Jr.↗
DOE OSTI2020

Surface engineering to enhance heat generation and joint strength in dissimilar materials AZ31 and DP590 ultrasonic welding

A multiscale simulation approach was developed and employed to optimize the sheet surface conditions for higher interfacial temperature and joint strength in ultrasonic welding of magnesium alloy AZ31 and dual-phase steel DP590. First, a mesoscale model was used to study the relationship between friction coefficient and surface roughness, which can be modified by various engineering methods. Then a macroscopic process model was employed to study the effects of surface roughness on heat generation, indicating that a temperature increase can be achieved with rougher surfaces on two sides of both DP590 and AZ31 sheets. Samples prepared by sanding and filing, as well as grinding, were first characterized for surface roughness and then welded under ultrasonic vibration. An infrared camera was used to measure temperatures in situ for model validation. Overall, lap shear test results for the welded joint showed that the joint strength can be improved by 10~25% using filing and round grinding methods as a result of the enhanced heat generation and mechanical interlocking on the interface.

42 ENGINEERING↗
NASA NTRS1981

Remote sensing of soil moisture content over bare field at 1.4 GHz frequency

An algorithm for estimating moisture content of a bare soil from the observed brightness temperature at 1.4 GHz is discussed and applied to a limited data base. The method is based on a radiative transfer model calculation, which has been successfully used in the past to account for many observational results, with some modifications to take into account the effect of surface roughness. Besides the measured brightness temperatures, the three additional inputs required by the method are the effective soil thermodynamic temperature, the precise relation between moisture content and the smooth field brightness temperatures and a pair of parameters related to surface roughness. The procedures of estimating surface roughness parameters and of obtaining moisture content from observed brightness temperature are discussed. The algorithm is applied to observations from truck mounted and airborne radiometers. The estimated moisture contents compare favorably with the observations in the top 2 cm layer.

Wang, J. R.↗
NASA NTRS1980

Microwave radiometer measurements of soil moisture content

A unique set of radiometer measurements is presented, recorded during a 1000-h day and night monitoring of irrigated fields from fully saturated to completely dry. Radiometer measurements were recorded at 2.8-cm (X-band) and 21.4-cm (L-band) wavelengths for a range of incident angles from nadir to 50 deg. Soil moisture and soil temperature profile measurements were recorded to a depth of 15 cm. The test site was located in east-central Texas on a clay soil (Miller clay). Three bare-surface plots were used, each having a distinctly different surface roughness. Vegetated plots were also measured. The data quantify the sensitivity of microwave radiometer measurements to soil moisture variations, the effect of surface roughness on the measurement, and the influence of surface vegetation.

Newton, R. W.↗
NASA NTRS1999

Segmented Mirror Image Degradation Due to Surface Dust, Alignment and Figure

In 1996 an algorithm was developed to include the effects of surface roughness in the calculation of the point spread function of a telescope mirror. This algorithm has been extended to include the effects of alignment errors and figure errors for the individual elements, and an overall contamination by surface dust. The final algorithm builds an array for a guard-banded pupil function of a mirror that may or may not have a central hole, a central reflecting segment, or an outer ring of segments. The central hole, central reflecting segment, and outer ring may be circular or polygonal, and the outer segments may have trimmed comers. The modeled point spread functions show that x-tilt and y-tilt, or the corresponding R-tilt and theta-tilt for a segment in an outer ring, is readily apparent for maximum wavefront errors of 0.1 lambda. A similar sized piston error is also apparent, but integral wavelength piston errors are not. Severe piston error introduces a focus error of the opposite sign, so piston could be adjusted to compensate for segments with varying focal lengths. Dust affects the image principally by decreasing the Strehl ratio, or peak intensity of the image. For an eight-meter telescope a 25% coverage by dust produced a scattered light intensity of 10(exp -9) of the peak intensity, a level well below detectability.

Schreur, Julian J.↗
NASA NTRS2014

Distributed Roughness Effects on Blunt-Body Transition and Turbulent Heating

An experimental program has been conducted to obtain data on the effects of surface roughness on blunt bodies at laminar, transitional, and turbulent conditions. Wind tunnel models with distributed surface roughness heights from 0.06 mm to 1.75 mm were tested and heating data were obtained using global surface thermography. Heating rates of up to 85% higher than predicted, smooth-surface turbulent levels were measured.

Hollis, Brian R.↗
NASA NTRS1950

The effects of variations in Reynolds number between 3.0 x 10sub6 and 25.0 x 10sub6 upon the aerodynamic characteristics of a number of NACA 6-series airfoil sections

Results are presented of an investigation made to determine the two-dimensional lift and drag characteristics of nine NACA 6-series airfoil section at Reynolds numbers of 15.0 x 10sub6, 20.0 x 10sub6, and 25.0 x 10sub6. Also presented are data from NACA Technical Report 824 for the same airfoils at Reynolds numbers of 3.0 x 10sub6, 6.0 x 10sub6, and 9.0 x 10sub6. The airfoils selected represent sections having variations in the airfoil thickness, thickness form, and camber. The characteristics of an airfoil with a split flap were determined in one instance, as was the effect of surface roughness. Qualitative explanations in terms of flow behavior are advanced for the observed types of scale effect.

Loftin, Laurence K, Jr↗
NASA NTRS1986

Erosive burning research

A status report is given on the results for the completed tests in a series of motor firings being carried out to measure the effects of the parameters that are considered to most strongly influence the scaling to larger rocket motor sizes of the transition to/or threshold conditions for erosive burning rate augmentation. Propellant burning rates at locations along the axis of the test motors are measured with a newly developed plasma capacitance gauge technique. The measured results are compared with erosive-burning predictions from a supporting ballistics analysis. The completed motor firings have successfully demonstrated response to the designed test variables. The trends with varying propellant burning rate, chamber pressure, and mass flow rate are consistent with existing results, but no pronounced effect of surface roughness has been observed. Rather, the influence of propellant oxidizer particle size on erosive burning is through its effect on the base, no-corssflow burning rate.

Strand, L.↗
NASA NTRS1985

Calculations of microwave brightness temperature of rough soil surfaces: Bare field

A model for simulating the brightness temperatures of soils with rough surfaces is developed. The surface emissivity of the soil media is obtained by the integration of the bistatic scattering coefficients for rough surfaces. The roughness of a soil surface is characterized by two parameters, the surface height standard deviation sigma and its horizontal correlation length l. The model calculations are compared to the measured angular variations of the polarized brightness temperatures at both 1.4 GHz and 5 GHz frequences. A nonlinear least-squares fitting method is used to obtain the values of delta and l that best characterize the surface roughness. The effect of shadowing is incorporated by introducing a function S(theta), which represents the probability that a point on a rough surface is not shadowed by other parts of the surface. The model results for the horizontal polarization are in excellent agreement with the data. However, for the vertical polarization, some discrepancies exist between the calculations and data, particularly at the 1.4 GHz frequency. Possible causes of the discrepancy are discussed.

Mo, T.↗
NASA NTRS1985

Calculations of microwave brightness temperature of rough soil surfaces

A model for simulating the brightness temperatures of soils with rough surfaces is developed. The surface emissivity of the soil media is obtained by the integration of the bistatic scattering coefficients for rough surfaces. The roughness of a soil surface is characterized by two parameters, the surface height standard deviation sigma and its horizontal correlation length l. The model calculations are compared to the measured angular variations of the polarized brightness temperatures at both 1.4 GHz and 5 GHz frequencies. A nonlinear least-squares fitting method is used to obtain the values of delta and l that best characterize the surface roughness. The effect of shadowing is incorporated by introducing a function S(theta), which represents the probability that a point on a rough surface is not shadowed by other parts of the surface. The model results for the horizontal polarization are in excellent agreement with the data. However, for the vertical polarization, some discrepancies exist between the calculations and data, particularly at the 1.4 GHz frequency. Possible causes of the discrepancy are discussed.

Mo, T.↗
NASA NTRS1974

The effects of particle size on the optical properties and surface roughness of a glass-balloon-filled black paint

The effects of particle size on the optical properties and surface roughness of a glass-balloon-filled, carbon-pigmented paint were studied in order to develop a diffuse-reflecting, low-total-reflectance, low-outgassing black paint. Particle sizes ranged between 20 microns and 74 microns. Surface roughness was found to increase with increasing particle size. Relative total reflectance at near-normal incidence (MgO standard) of the filled paints was less than for the unfilled paint between 230 nm and 1800 nm. Total absolute reflectance at 546 nm decreased with increasing particle size at grazing angles of incidence. Near-normal, total emittance was greater for the filled paints than for the unfilled paint. Specularity decreased with increasing particle size over the range studied.

Heslin, T.↗
DOE OSTI2022

Fatigue performance of laser powder bed fusion hydride-dehydride Ti-6Al-4V powder

We report hydride-dehydride (HDH) Ti-6Al-4V alloy with particle size distribution of 50–120 µm is laser powder bed fusion (L-PBF) processed using optimum processing parameters and a near-fully dense structure with a density of 99.9 % is achieved. Microstructural observations and phase analyses indicate formation of columnar β grains with acicular α/α' phases in as-built condition. The roughness of the as-fabricated samples is significant with an average roughness of R a = 15.71 ± 3.96 µm and a root mean square roughness of R rms = 108.4 ± 24.9 µm, however, both values are reduced to R a = 0.19 ± 0.04 µm and R rms = 4.9 ± 0.6 µm after mechanical grinding. Mechanical tests are carried out on as-fabricated specimens followed by stress relief treatment. All samples are tested to failure in fatigue, under fully-reversed tension-compression conditions of R = –1. The as-built samples failed from the surface with crack initiation mainly at micro-notches, whereas after mechanically grinding, crack initiation changed to subsurface defects such as pores. Minimizing surface roughness by mechanically grinding eliminates surface micro-notches which improves fatigue strength in the high cycle fatigue region. Fatigue notch factor calculations showed that the effect of surface roughness was significantly lower when HDH powder is used compared to standard spherical powder. X-ray diffraction analysis revealed an in-plane compressive stress, micro-strain and grain refinement on the surface of the mechanically ground samples. Fractography observations (macroscale) revealed a fully brittle fracture in the first stage of crack growth with a transition to a dominantly ductile fracture in the third stage of crack growth. On the other hand, at the micro scale, even the brittle fracture regions showed evidence of ductile fracture within the α' martensite laths.

36 MATERIALS SCIENCE↗