Results for “SRM” — Page 12

NASA NTRS1995

Marshall Space Flight Center surface modeling and grid generation applications

The Solid Rocket Motors (SRM) used by NASA to propel the Space Shuttle employ gimballing nozzles as a means for vehicular guidance during launch and ascent. Gimballing a nozzle renders the pressure field of the exhaust gases nonaxisymmetric. This has two effects: (1) it exerts a torque and side load on the nozzle; and (2) the exhaust gases flow circumferentially in the aft-dome region, thermally loading the flexible boot, case-to-nozzle joint, and casing insulation. The use of CFD models to simulate such flows is imperative in order to assess SRM design. The grids for these problems were constructed by obtaining information from drawings and tabulated coordinates. The 2D axisymmetric grids were designed and generated using the EZ-Surf and GEN2D surface and grid generation codes. These 2D grids were solved using codes such as FDNS, GASP, and MINT. These axisymmetric grids were rotated around the center-line to form 3D nongimballed grids. These were then gimballed around the pivot point and the gaps or overlaps resurfaced to obtain the final domains, which contained approximately 366,000 grid points. The 2D solutions were then rotated and manipulated as appropriate for geometry and used as initial guesses in the final solution. The analyses were used in answering questions about flight criteria.

Williams, Robert W.↗

NASA NTRS1999

Flow Simulation of Solid Rocket Motors: Injection Induced Water-Flow Tests from Porous Media - 1

Prior to selecting a proper porous material for use in simulating the internal port flow of a solid rocket motor (SRM), in cold-flow testing, the flow emerging from porous materials is experimentally investigated. The injection-flow emerging from a porous matrix always exhibits a lumpy velocity profile that is spatially stable and affects the development of the longitudinal port flow. This flow instability, termed pseudoturbulence, is an inherent signature of the porous matrix and is found to generally increase with the wall porosity and with the injection flow rate. Visualization studies further show that the flow from porous walls made from shaving-type material (sintered stainless-steel) exhibits strong recirculation zones that are conspicuously absent in walls made from nodular or spherical material (sintered bronze). Detailed flow visualization observations and hot-film measurements are reported from tests of injection-flow and a coupled cross-flow from different porous wall materials. Based on the experimental data, discussion is provided on the choice of suitable material for SRM model testing while addressing the consequences and shortcomings from such a test.

Ramachandran, N.↗

NASA NTRS1999

The 260: The Largest Solid Rocket Motor Ever Tested

Aerojet in the mid 1960s, under contract to NASA, built and static hot fire tested the largest solid rocket motor (SRM) in history for the purpose of demonstrating the feasibility of utilizing large SRMs for space exploration. This program successfully fabricated two high strength steel chambers, loaded each with approximately 1,68 million pounds of propellant, and static test fired these giants with their nozzles up from an underground silo located adjacent to the Florida everglades. Maximum thrust and total impulse in excess of 5,000,000 lbf and 3,470,000,000 lbf-sec were achieved. Flames from the second firing, conducted at night, were seen over eighty miles away. For comparative purposes: the thrust developed was nearly 100 times that of a Minuteman III second stage and the 260 in.-dia cross-section was over 3 times that of the Space Shuttle SRM.

Crimmins, P.↗

NASA NTRS2000

Internal Flow Analysis of Large L/D Solid Rocket Motors

Traditionally, Solid Rocket Motor (SRM) internal ballistic performance has been analyzed and predicted with either zero-dimensional (volume filling) codes or one-dimensional ballistics codes. One dimensional simulation of SRM performance is only necessary for ignition modeling, or for motors that have large length to port diameter ratios which exhibit an axial "pressure drop" during the early burn times. This type of prediction works quite well for many types of motors, however, when motor aspect ratios get large, and port to throat ratios get closer to one, two dimensional effects can become significant. The initial propellant grain configuration for the Space Shuttle Reusable Solid Rocket Motor (RSRM) was analyzed with 2-D, steady, axi-symmetric computational fluid dynamics (CFD). The results of the CFD analysis show that the steady-state performance prediction at the initial burn geometry, in general, agrees well with 1-D transient prediction results at an early time, however, significant features of the 2-D flow are captured with the CFD results that would otherwise go unnoticed. Capturing these subtle differences gives a greater confidence to modeling accuracy, and additional insight with which to model secondary internal flow effects like erosive burning. Detailed analysis of the 2-D flowfield has led to the discovery of its hidden 1-D isentropic behavior, and provided the means for a thorough and simplified understanding of internal solid rocket motor flow. Performance parameters such as nozzle stagnation pressure, static pressure drop, characteristic velocity, thrust and specific impulse are discussed in detail and compared for different modeling and prediction methods. The predicted performance using both the 1-D codes and the CFD results are compared with measured data obtained from static tests of the RSRM. The differences and limitations of predictions using ID and 2-D flow fields are discussed and some suggestions for the design of large L/D motors and more critically, motors with port to throat ratios near one, are covered.

Laubacher, Brian A.↗

NASA NTRS2010

Space Shuttle Reusable Solid Rocket Motor

RSRM is a highly reliable human-rated Solid Rocket Motor: a) Largest diameter SRM to achieve flight status; b) Only human-rated SRM. RSRM reliability achieved by: a)Applying special attention to Process Control, Testing, and Postflight; b) Communicating often; c) Identifying and addressing issues in a disciplined approach; d) Identifying and fully dispositioning "out-of-family" conditions; e) Addressing minority opinions; and f) Learning our lessons.

Moore, Dennis↗

NASA NTRS2011

5 Percent Ares I Scale Model Acoustic Test: Overpressure Characterization and Analysis

During the ignition of a ducted solid rocket motor (SRM), rapid expansion of injected hot gases from the motor into a confined volume causes the development of a steep fronted wave. This low frequency transient wave propagates outward from the exhaust duct, impinging the vehicle and ground structures. An unsuppressed overpressure wave can potentially cause modal excitation in the structures and vehicle, subsequently leading to damage. This presentation details the ignition transient f indings from the 5% Ares I Scale Model Acoustic Test (ASMAT). The primary events of the ignition transient environment induced by the SRM are the ignition overpressure (IOP), duct overpressure (DOP), and source overpressure (SOP). The resulting observations include successful knockdown of the IOP environment through use of a Space Shuttle derived IOP suppression system, a potential load applied to the vehicle stemming from instantaneous asymmetrical IOP and DOP wave impingement, and launch complex geometric influences on the environment. The results are scaled to a full-scale Ares I equivalent and compared with heritage data including Ares I-X and both suppressed and unsuppressed Space Shuttle IOP environments.

Alvord, David↗

NASA NTRS2011

Reusable Solid Rocket Motor - Accomplishment, Lessons, and a Culture of Success

The Reusable Solid Rocket Motor (RSRM) represents the largest solid rocket motor (SRM) ever flown and the only human-rated solid motor. High reliability of the RSRM has been the result of challenges addressed and lessons learned. Advancements have resulted by applying attention to process control, testing, and postflight through timely and thorough communication in dealing with all issues. A structured and disciplined approach was taken to identify and disposition all concerns. Careful consideration and application of alternate opinions was embraced. Focus was placed on process control, ground test programs, and postflight assessment. Process control is mandatory for an SRM, because an acceptance test of the delivered product is not feasible. The RSRM maintained both full-scale and subscale test articles, which enabled continuous improvement of design and evaluation of process control and material behavior. Additionally RSRM reliability was achieved through attention to detail in post flight assessment to observe any shift in performance. The postflight analysis and inspections provided invaluable reliability data as it enables observation of actual flight performance, most of which would not be available if the motors were not recovered. RSRM reusability offered unique opportunities to learn about the hardware. NASA is moving forward with the Space Launch System that incorporates propulsion systems that takes advantage of the heritage Shuttle and Ares solid motor programs. These unique challenges, features of the RSRM, materials and manufacturing issues, and design improvements will be discussed in the paper.

Moore, D. R.↗

NASA NTRS2006

Quantity Distance for the Kennedy Space Center Vehicle Assembly Building for Solid Propellant Fueled Launchers

The NASA KSC VAB was built to process Apollo launchers in the 1960's, and later adapted to process Space Shuttles. The VAB has served as a place to assemble solid rocket motors (5RM) and mate them to the vehicle's external fuel tank and Orbiter before rollout to the launch pad. As Space Shuttle is phased out, and new launchers are developed, the VAB may again be adapted to process these new launchers. Current launch vehicle designs call for continued and perhaps increased use of SRM segments; hence, the safe separation distances are in the process of being re-calculated. Cognizant NASA personnel and the solid rocket contractor have revisited the above VAB QD considerations and suggest that it may be revised to allow a greater number of motor segments within the VAB. This revision assumes that an inadvertent ignition of one SRM stack in its High Bay need not cause immediate and complete involvement of boosters that are part of a vehicle in adjacent High Bay. To support this assumption, NASA and contractor personnel proposed a strawman test approach for obtaining subscale data that may be used to develop phenomenological insight and to develop confidence in an analysis model for later use on full-scale situations. A team of subject matter experts in safety and siting of propellants and explosives were assembled to review the subscale test approach and provide options to NASA. Upon deliberations regarding the various options, the team arrived at some preliminary recommendations for NASA.

Stover, Steven↗

NASA NTRS2017

Validation of a Solid Rocket Motor Internal Environment Model

In a prior effort, a thermal/fluid model of the interior of Penn State University's laboratory-scale Insulation Test Motor (ITM) was constructed to predict both the convective and radiative heat transfer to the interior walls of the ITM with a minimum of empiricism. These predictions were then compared to values of total and radiative heat flux measured in a previous series of ITM test firings to assess the capabilities and shortcomings of the chosen modeling approach. Though the calculated fluxes reasonably agreed with those measured during testing, this exercise revealed means of improving the fidelity of the model to, in the case of the thermal radiation, enable direct comparison of the measured and calculated fluxes and, for the total heat flux, compute a value indicative of the average measured condition. By replacing the P1-Approximation with the discrete ordinates (DO) model for the solution of the gray radiative transfer equation, the radiation intensity field in the optically thin region near the radiometer is accurately estimated, allowing the thermal radiation flux to be calculated on the heat-flux sensor itself, which was then compared directly to the measured values. Though the fully coupling the wall thermal response with the flow model was not attempted due to the excessive computational time required, a separate wall thermal response model was used to better estimate the average temperature of the graphite surfaces upstream of the heat flux gauges and improve the accuracy of both the total and radiative heat flux computations. The success of this modeling approach increases confidence in the ability of state-of-the-art thermal and fluid modeling to accurately predict SRM internal environments, offers corrections to older methods, and supplies a tool for further studies of the dynamics of SRM interiors.

Martin, Heath T.↗

NASA NTRS2017

Validation of a Solid Rocket Motor Internal Environment Model

In a prior effort, a thermal/fluid model of the interior of Penn State University's laboratory-scale Insulation Test Motor (ITM) was constructed to predict both the convective and radiative heat transfer to the interior walls of the ITM with a minimum of empiricism. These predictions were then compared to values of total and radiative heat flux measured in a previous series of ITM test firings to assess the capabilities and shortcomings of the chosen modeling approach. Though the calculated fluxes reasonably agreed with those measured during testing, this exercise revealed means of improving the fidelity of the model to, in the case of the thermal radiation, enable direct comparison of the measured and calculated fluxes and, for the total heat flux, compute a value indicative of the average measured condition. By replacing the P1-Approximation with the discrete ordinates (DO) model for the solution of the gray radiative transfer equation, the radiation intensity field in the optically thin region near the radiometer is accurately estimated, allowing the thermal radiation flux to be calculated on the heat-flux sensor itself, which was then compared directly to the measured values. Though the fully coupling the wall thermal response with the flow model was not attempted due to the excessive computational time required, a separate wall thermal response model was used to better estimate the average temperature of the graphite surfaces upstream of the heat flux gauges and improve the accuracy of both the total and radiative heat flux computations. The success of this modeling approach increases confidence in the ability of state-of-the-art thermal and fluid modeling to accurately predict SRM internal environments, offers corrections to older methods, and supplies a tool for further studies of the dynamics of SRM interiors.

Martin, Heath T.↗

NASA NTRS2019

Mission Design for the Lunar Pallet Lander

Due to lighting conditions, the program decided to only fly to the north pole in June 2022 and south pole in December 2022. Starting with the June 2022 landing sites at the north pole, a trajectory scan was run for one landing per day for the latitudes from 85 up to 88 degrees at 0.5 degree increments. Each landing site was at lunar dawn, which determined the landing site’s longitude as described in the previous section. The results of the June 2022 scan showed that LPL had the capability to reach a landing site at least once per day for the region examined as see in in Figure 12. There appears to be a correlation between the landing site’s altitude and the propellant remaining above the lander’s FPR, Figure 13. This is most likely due to the >10 km altitude constraint at SRM burnout. This constraint was applied to keep the lander high above the lunar terrain to avoid mountains, but can be relaxed when the full terrain data is added. Figure 12. June 2022 Nominal Usable Propellant Remaining vs Landing Date/time Similarly, the December 2022 landing sites were run showing that LPL was also capable of reaching a landing site at the Moon at least once per day. Figure 14 shows the results of the December scan, however, there were 3 landing sites that LPL could not reach. Two were very low in altitude (-5 and -4 km in altitude), which looking at the altitude trends in Figure 15, indicates that these sites may not be feasible with the current mission design. It may be possible to achieve the low altitude landing sites by lowering the SRM burnout altitude constraint, but that requires detailed terrain modeling, planned for a future phase of the analysis. The third non-reachable landing site is most likely due to an optimization error, as its altitude was high enough, at -2 km, that it should not have been a problem for the lander to arrive there. More analysis is required to verify this observation.

Craig, Scott↗

NASA NTRS2019

Analyses and Methods of Solid Rocket Motor Material Irradiation at Marshall Space Flight Center

The search for life on other worlds is among humanity’s greatest endeavors. Europa represents the most probable location to discover extraterrestrial life in our solar system, owing to its surface composition of ice covering a liquid water ocean, warmed by the tidal forces of its orbit around Jupiter. Unfortunately, the Jovian system hosts the most intense planetary radiation environment in the solar system due to the charged particles, namely electrons and protons, trapped by Jupiter’s immense magnetic field. Any mission that attempts to approach or land on Europa must survive this radiation environment [Hand et al, 2017]. Radiation effects were identified as a priority risk to the successful development of a de-orbit stage and solid rocket motor (SRM) early in the Europa Lander De-orbit Stage project concept. The effects of primary concern tend to occur very near the outer surface of the SRM. The charged particles deposit their energy quickly and are mostly stopped in the outer metallic case, but a significant portion of radiation penetrates through the bondline and outer propellant regions. High doses of ionizing radiation are known to cause significant changes to mechanical properties of many materials, especially polymers. For polymers such as the rubber-like materials (elastomers) in a solid rocket motor, the primary damage mechanism is known as cross-linking, in which ionization causes the restructuring of the matrix of long polymer chains. Ionization energy breaks the long polymer chains and allows formation of new cross-linked bonding sites. This hardens and often strengthens the polymer, but at the cost of decreased flexibility (or modulus). Propellant, insulation, liner, and pyrotechnic materials were identified as higher risk items, and so were irradiated at Marshall Space Flight Center (MSFC) for investigation of changes in mechanical and ballistic properties. This process required significant levels of analysis to evaluate how the radiation environment evolves within the spacecraft during the mission, and also to evaluate how dose is delivered into test articles within the irradiating facilities.

Caffrey, Jarvis↗

NASA NTRS2019

Analyses and Methods of Solid Rocket Motor Material Irradiation at Marshall Space Flight Center

The search for life on other worlds is among humanity’s greatest endeavors. Europa represents the most probable location to discover extraterrestrial life in our solar system, owing to its surface composition of ice covering a liquid water ocean, warmed by the tidal forces of its orbit around Jupiter. Unfortunately, the Jovian system hosts the most intense planetary radiation environment in the solar system due to the charged particles, namely electrons and protons, trapped by Jupiter’s immense magnetic field. Any mission that attempts to approach or land on Europa must survive this radiation environment [Hand et al, 2017]. Radiation effects were identified as a priority risk to the successful development of a de-orbit stage and solid rocket motor (SRM) early in the Europa Lander De-orbit Stage project concept. The effects of primary concern tend to occur very near the outer surface of the SRM. The charged particles deposit their energy quickly and are mostly stopped in the outer metallic case, but a significant portion of radiation penetrates through the bondline and outer propellant regions. High doses of ionizing radiation are known to cause significant changes to mechanical properties of many materials, especially polymers. For polymers such as the rubber-like materials (elastomers) in a solid rocket motor, the primary damage mechanism is known as cross-linking, in which ionization causes the restructuring of the matrix of long polymer chains. Ionization energy breaks the long polymer chains and allows formation of new cross-linked bonding sites. This hardens and often strengthens the polymer, but at the cost of decreased flexibility (or modulus). Propellant, insulation, liner, and pyrotechnic materials were identified as higher risk items, and so were irradiated at Marshall Space Flight Center (MSFC) for investigation of changes in mechanical and ballistic properties. This process required significant levels of analysis to evaluate how the radiation environment evolves within the spacecraft during the mission, and also to evaluate how dose is delivered into test articles within the irradiating facilities.

Caffrey, Jarvis↗

NASA NTRS2020

System Engineering a Solar Thermal Propulsion Mission Concept for Rapid Interstellar Medium Access

The interstellar medium (ISM) represents the next frontier in space exploration, with many new discoveries to be made. The challenge, being so far away from Earth, the ISM requires many decades to reach. To advance our knowledge of what exists beyond our Solar System, new approaches for rapid access are required. One such approach is solar thermal propulsion (STP). The approach uses several Venus and Earth gravity assists to fly to Jupiter and use its gravity well to dive towards the Sun. Approaching within 3 solar radii a perihelion burn would be performed, maximizing the spacecraft’s ΔV to achieve high Solar System escape velocities. A unique aspect of the STP mission concept is that the Sun is not only used as a gravity well for an Oberth manoeuvre, but also to heat the fuel to ultra-high-temperatures (>3000 K), enabling a monopropellant burn with high specific impulse (Isp). Prior preliminary studies indicated escape velocities of over 20 astronomical unit (AU)/yr would be possible. An in-depth modelling exercise was undertaken to determine how such a system would perform. The model in this paper showed the current STP design is capable of providing just under 9±1 AU/yr, but there are many technology developments that could increase escape velocity. The technologies vary from items that could be implemented in the near term, like turbo-pumps driven by the hydrogen, to items requiring more extensive development programs like thin coatings which do not erode in superheated hydrogen. After reviewing the STP approach, and comparing it to a solid rocket motor (SRM), it was found that with currently available technology, SRM outperforms STP with an escape velocity of approximately 10-12 AU/yr. However, future advances in heat exchanger lining materials, turbo pumps, and advanced heat exchanger geometries may enable solar thermal propulsion to provide higher escape velocities, providing one of the fastest ways to exit the solar system. Ultimately, if all technology paths could be implemented with minimal side effects, the performance in a best-case scenario could reach up to 16 AU/yr.

Alkalai, Leon↗

NASA NTRSDate not supplied

SLS Ignition Overpressure-Sound Suppression System Performance Evaluated Against Historical Configurations

During the start-up of a number of launch vehicles that include solid rocket motor (SRM), the ignition transient and acoustic environments are mitigated by the implementation of a water spray system located immediately below the SRM nozzle exit plane (NEP). For NASA’s Space Launch System (SLS), this water system is referred to as the Ignition Overpressure / Sound Suppression (IOP/SS) system. The SLS Induced Environments (IE) technical discipline conducted a comprehensive evaluation of the design and as-tested performance of the IOP/SS water that will operate underneath both Boosters during the Artemis I launch. As part of this evaluation, flow rates and imagery from a number of integrated launch pad / mobile launcher IOP/SS flow tests were studied. Additional insight was leveraged from the Shuttle heritage IOP/SS system that includes data and imagery from a number of Flight Readiness Firings (FRF) and water flow tests. Lastly, the IE study included a qualitive comparison of the Shuttle and SLS systems to the equivalent water flow systems for Titan and Atlas V and determined that the NASA water flow systems are substantially different than those supporting other launch vehicles.

Ignition Overpressure↗

NASA NTRSDate not supplied

SLS Ignition Overpressure-Sound Suppression System Performance Evaluated Against Historical Configurations

During the start-up of a number of launch vehicles that include solid rocket motor (SRM), the ignition transient and acoustic environments are mitigated by the implementation of a water spray system located immediately below the SRM nozzle exit plane (NEP). For NASA’s Space Launch System (SLS), this water system is referred to as the Ignition Overpressure / Sound Suppression (IOP/SS) system. The SLS Induced Environments (IE) technical discipline conducted a comprehensive evaluation of the design and as-tested performance of the IOP/SS water that will operate underneath both Boosters during the Artemis I launch. As part of this evaluation, flow rates and imagery from a number of integrated launch pad / mobile launcher IOP/SS flow tests were studied. Additional insight was leveraged from the Shuttle heritage IOP/SS system that includes data and imagery from a number of Flight Readiness Firings (FRF) and water flow tests. Lastly, the IE study included a qualitive comparison of the Shuttle and SLS systems to the equivalent water flow systems for Titan and Atlas V and determined that the NASA water flow systems are substantially different than those supporting other launch vehicles.

Ignition Overpressure↗

DOE OSTI2025

ClimGen: Learning the Forcing-Response Relationship in Climate System

Solar Radiation Management (SRM) is emerging as a potential geoengineering strategy to address the anthropogenic impact on climate, but its effective implementation requires an iterative and large ensemble of highly accurate and efficient climate projections. Traditional climate projections rely on executing computationally demanding and time-consuming numerical climate models. Recent advances in machine learning (ML) aim to enhance these approaches by emulating traditional methods. In this work, we propose a novel framework for directly learning the relationship between solar radiation flux at the top of the atmosphere and the corresponding surface temperature response. To evaluate the feasibility of this direct ML-based projection, we developed a dataset using an intermediate complexity model, incorporating a comprehensive suite of different forcing patterns and evaluation metrics to rigorously assess the ML model’s performance. We introduce a Conditional Denoising Diffusion Probabilistic Model (cDDPM) for this task, which demonstrates encouraging skill in representing climate statistics under previously unseen forcing patterns. This approach provides a promising pathway for direct climate projections by accurately learning the forcing-response relationship, with a wide range of applications in impact mitigation, emissions policy design, and SRM strategies.

Chen, Tse-Chun [BATTELLE (PACIFIC NW LAB)] (ORCID:↗

DOE OSTI2020

Comprehensive Detection of Single Amino Acid Variants and Evaluation of Their Deleterious Potential in a PANC-1 Cell Line

Identifying single amino acid variants (SAAVs) in cancer is critical for precision oncology. Several advanced algorithms are now available to identify SAAVs but attempts to combine different algorithms and optimize them on large datasets to achieve a more comprehensive coverage of SAAVs have not been implemented. Herein we report an expanded detection of SAAVs in the PANC-1 cell line using three different strategies, which results in identification of 540 SAAVs in the mass spectrometry data, the most comprehensive coverage yet reported. Among the set of 540 SAAVs, 79 are evaluated as deleterious SAAVs based on analysis using novel AssVar software in which one of the driver mutations found in each protein of KRAS, TP53 and SLC37A4 is further validated using independent selected reaction monitoring (SRM) analysis. Our study represents the most comprehensive discovery of SAAVs to date and the first large-scale detection of deleterious SAAVs in the PANC-1 cell line. This work may serve as the basis for future research in pancreatic cancer and personal immunotherapy and treatment.

59 BASIC BIOLOGICAL SCIENCES↗