Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SOOT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Progression of soot cake layer properties during the systematic regeneration of diesel particulate filters measured with neutron tomography

Although particulate filters (PFs) have been a key component of the emission control system for modern diesel engines, there remain significant questions about the basic regeneration behavior of the filters and how it changes with accumulation of increasing soot layers. This effort describes a systematic deposition and regeneration of particulate matter in 25-mm diameter × 76-mm long wall-flow PFs composed of silicon carbide (SiC) material. The initial soot distributions were analyzed for soot cake thickness using a nondestructive neutron imaging technique. With the PFs intact, it was then possible to sequentially regenerate the samples and reanalyze them, which was performed after nominal 20, 50, and 70 % regenerations. The loaded samples show a relatively uniform distribution of particulate with an increasing soot cake thickness and nearly identical initial density of 70 mg/cm 3 . Throughout regeneration, the soot cake thickness initially decreases significantly while the density increases to 80–90 mg/cm 3 . After ~50 % regeneration, the soot cake thickness stays relatively constant, but instead, the density decreases as pores open up in the layer (~35 mg/cm 3 at 70 % regeneration). Here, complete regeneration initially occurs at the rear of the PF channels. With this information, a conceptual model of the regeneration is proposed.

54 ENVIRONMENTAL SCIENCES↗

Flow Reactor Study of the Soot Precursors of Novel Cycloalkanes as Synthetic Jet Fuel Compounds: Octahydroindene, p -Menthane, and 1,4-Dimethylcyclooctane

Sustainable aviation fuels (SAFs) or Synthetic aviation turbine fuels (SATFs) derived from nonpetroleum sources are essential for energy security and a strong rural and agricultural economy. Airplanes operating on SAF can have lower particle emissions compared to those of conventional jet fuel, reducing air quality impacts near airports. Processing biobased isoprene or wood and agricultural waste can produce cycloalkane-rich fuels with properties meeting ASTM International’s SATF requirements. The unique structures of these cycloalkanes yield lower soot emissions because of their lack of aromatic rings. We measured the soot formation tendency as yield sooting index (YSI) and used laminar flow reactor experiments to evaluate soot precursors formed for isoprene-derived compounds p-menthane and 1,4-dimethylcyclooctane (DMCO), and octahydroindene (OHI)─ produced from woody biomass via catalytic fast pyrolysis. The combustion chemistry of the OHI and DMCO has not been previously studied. Experiments were conducted at 10 bar from 800 to 1200 K, equivalence ratios of 1.0 and 3.0, and residence times of 1.0 and 0.6 s, respectively. Experimentally detected species were used to elucidate the mechanisms of soot precursor formation. OHI exhibited the highest YSI (94.5) and formed a high concentration of benzene primarily by direct dehydrogenation of the six-membered ring. p-Menthane (YSI 92.0) and DMCO (YSI 85.0) oxidation products included fewer aromatic components but higher benzene precursors, including 1,3-butadiene, propyne, and allene. This suggests that the ring-opening pathway is dominant over the dehydrogenation pathway in the benzene formation for these compounds. This experimental speciation provides insight into the influence of the cycloalkane structure on the sooting tendencies of potential SAF blend components, thereby aiding in fuel design processes.

09 BIOMASS FUELS↗

Soot formation in aerodynamically strained methane-air and ethylene-air diffusion flames with chloromethane addition

The effects of chloromethane (CH{sub 3}Cl) addition on soot inception in methane-air and ethylene-air counterflow diffusion flames were investigated by varying the concentrations of chloromethane and nitrogen in the fuel stream. Experiments showed a monotonic increase in the critical sooting stretch rate for methane-air flames when methane was replaced by chloromethane, while ethylene and chloromethane flames exhibited a larger sooting tendency than flames under comparable conditions and burning either ethylene or chloromethane alone. For the conditions investigated, the critical sooting stretch rates of methane-chloromethane-nitrogen flames were shown to be primarily a function of the chloromethane loading in the fuel stream. The structure of these flames was modeled using detailed chemistry and transport. Modeling results suggested that the enhancement of soot formation in ethylene-chloromethane flames may be a combined result of increased concentrations of C{sub 2} species and chlorinated C{sub 1} radicals (CH{sub 2}Cl and CHCl). A large rate of the reactions among these species may be the first steps in the molecular growth processes, which leads to the inception of soot particles. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of radiation on spray flame characteristics and soot formation

Two-dimensional numerical simulations are applied to spray flames formed in a laminar counterflow and the effects of radiation on spray flame characteristics and soot formation are studied. N-Decane (C{sub 10}H{sub 22}) is used as the liquid fuel, and the droplet motion is calculated by the Lagrangian method. A single-step global reaction is employed for the combustion reaction model. A kinetically based soot model with a flamelet model is used to predict soot formation. Radiation is taken into account using the discrete ordinate method. The results show that radiation strongly affects the spray flame behavior and soot formation. Without the radiation model, flame temperature and soot volume fraction are greatly overestimated. The soot is formed in the diffusion flame regime, and its radiation emission increases with the increase in the equivalence ratio of the droplet fuel. This trend is in good agreement with that of the luminous flame behavior observed in the experiments. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Planar measurements of soot volume fraction and OH in a JP-8 pool fire

The simultaneous measurement of soot volume fraction by laser induced incandescence (LII) and qualitative imaging of OH by laser induced fluorescence (LIF) was performed in a JP-8 pool fire contained in a 152 mm diameter pan. Line of sight extinction was used to calibrate the LII system in a laminar flame, and to provide an independent method of measuring average soot volume fraction in the turbulent flame. The presence of soot in the turbulent flame was found to be approximately 50% probable, resulting in high levels of optical extinction, which increased slightly through the flame from approximately 30% near the base, to approximately 50% at the tip. This high soot loading pushes both techniques toward their detection limit. Nevertheless, useful accuracy was obtained, with the LII measurement of apparent extinction in the turbulent flame being approximately 21% lower than a direct measurement, consistent with the influence of signal trapping. The axial and radial distributions of soot volume fraction are presented, along with PDFs of volume fraction, and new insight into the behavior of soot sheets in pool fires are sought from the simultaneous measurements of OH and LII. (author)

02 PETROLEUM↗

Analyzing the effects of temperature on soot formation with a joint volume-surface-hydrogen model

The intent of the current work is to present and further validate a new tri-variate model for the formation of soot particles, to apply this model in analyzing the effects of temperature on the formation and growth of soot, and to compare the findings with the present understanding derived from numerous experimental studies. In this novel model, a particle is represented as a fractal shaped aggregate and is described by three independent quantities: the volume, the surface area, and the number of hydrogenated sites (or active sites) on the surface. The introduction of this third variable allows for a better description of the surface reactivity at high temperatures. This approach is extended by a model for the total carbon-to-hydrogen (C/H) ratio of the particle. The model is validated first in high temperature premixed ethylene flames, premixed benzene flames, an acetylene counterflow diffusion flame, and toluene pyrolysis in shock-tubes. Then, the soot volume fraction is computed for a series of atmospheric laminar ethylene premixed flames with varying flame temperatures. The soot model is shown to reproduce the well known bell-shaped temperature dependence of soot volume fraction, which was found in many experiments. It is observed that nucleation is the largest contributor to soot volume fraction at low temperatures while growth by surface reactions is more important at higher temperatures. The surface reactivity and the volumetric carbon-to-hydrogen ratio (C/H) are also computed as a function of temperature. The surface reactivity is found to depend not only on the temperature but also on the particle size and the residence time in the flame. Finally, as observed experimentally, the C/H ratio is found to be essentially constant and close to unity for low temperature flames and increases with residence time in high temperature flames. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of a uniform electric field on soot in laminar premixed ethylene/air flames

The effect of a nominally uniform electric field on the initially uniform distribution of soot has been assessed for laminar premixed ethylene/air flames from a McKenna burner. An electrophoretic influence on charged soot particles was measured through changes to the deposition rate of soot on the McKenna plug, using laser extinction (LE). Soot volume fraction was measured in situ using laser-induced incandescence (LII). Particle size and morphologies were assessed through ex situ transmission electron microscopy (TEM) using thermophoretic sampling particle diagnostics (TSPD). The results show that the majority of these soot particles are positively charged. The presence of a negatively charged plug was found to decrease the particle residence times in the flame and to influence the formation and oxidation progress. A positively charged plug has the opposite effect. The effect on soot volume fraction, particles size and morphology with electric field strength is also reported. Flame stability was also found to be affected by the presence of the electric field, with the balance of the electrophoretic force and drag force controlling the transition to unstable flame flicker. The presence of charged species generated by the flame was found to reduce the dielectric field strength to one seventh that of air. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Measuring the soot onset temperature in high-pressure n-dodecane spray pyrolysis

In this paper, soot formation in pyrolyzing sprays of n-dodecane is visualized and quantified in a high-pressure, high-temperature, constant-volume spray chamber at 38 bar, 76 bar, and 114 bar. Sprays of n-dodecane are injected at 500 bar from a single-hole, 186-µm orifice diameter fuel injector. We quantify the temporal evolution of the soot optical thickness and the total soot mass formed in the pyrolyzing sprays using a high-speed extinction imaging diagnostic. The vessel ambient temperature and pressure are varied independently to identify the soot onset temperature for n-dodecane pyrolysis. Linear extrapolation of the maximum soot formation rates as a function of ambient temperature reveals a soot onset temperature near 1450 K. Finally, the onset temperature determined here for n-dodecane is within 50 K of those previously measured along the centerline of atmospheric pressure coflow diffusion flames for smaller alkane fuels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

CARS thermometry in laminar sooting ethylene-air co-flow diffusion flames with nitrogen dilution

Temperature measurements were performed in nonpremixed, sooting jet flames using coherent anti-Stokes Raman scattering (CARS). The jet fluid was ethylene diluted with different concentrations of nitrogen, and the co-flow fluid was dry air. The flames were stabilized on a Yale burner, also known as Smooke/Long burner, and the operating conditions were chosen to match previous experiments on the burner by the Yale group and other research groups. The selected flames have also been identified as target flames by the International Sooting Flame Workshop. CARS measurements of temperature provide insight into the structure of these sooting flames and serve as benchmark data for comparison with computations. A dual-pump vibrational CARS system was used here in order to avoid soot interferences. We were able to obtain high quality CARS spectra in all regions of the flame including the highly sooting regions and near the exit of the fuel nozzle, where the nonresonant modulation of the nitrogen CARS spectrum is strong due to the high ethylene concentrations. The measurements are compared with CFD results in literature and discussed in context of measured soot volume fraction, also, from literature.

42 ENGINEERING↗

Role of fuel properties and piston shape in influencing soot oxidation in heavy-duty low swirl diesel engine combustion

The presented study evaluated effects on soot emissions of important diesel fuel properties (e.g. volatility T95, hydrogen to-carbon ratio H/C and oxygen content O/C) in a heavy-duty, low-swirl, direct injection diesel engine operated with cooled exhaust gas recirculation to control the emissions of nitrogen oxides. Variation of injection pressure was conducted in three representative operation points in the single-cylinder engine including conventional and wave piston bowl types. Additionally, detailed optical combustion studies were performed in a high pressure/high temperature combustion chamber with an engine-like flame-wall interaction geometry. The fuel properties mainly influenced parameters relating to events near the nozzle, such as the ignition delay, flame lift-off distance and spray air entrainment. Oxygenation of the fuel reduced soot formation (a known effect of spray-jet dilution), but the fuels’ H/C and T95 also influenced soot emissions. Viscosity, heating value and density, treated as secondary fuel parameters, affected the injected fuel’s kinetic energy, and hence mean flow field and local turbulent mixing late in the combustion cycle. The results suggested that fuel effects on soot oxidation during late phases of combustion are mainly governed by parameters related to the fuel injection profile under the specific cylinder gas conditions. With an oxygenated fuel, flow structures (local turbulent side vortices) which are typical for the investigated engine type were found to form in a similar way as with a reference fuel. Hence, improved internal flow using a wave piston in combination with a low-sooting oxygenated fuel gave additional reductions in net soot emissions.

42 ENGINEERING↗

Drastically different restructuring of airborne and surface-anchored soot aggregates

Combustion soot particles are fractal aggregates of hydrophobic spherules. Mixing of soot particles with other chemicals during atmospheric processing may partially offset their hydrophobicity, promoting water uptake and structural compaction. Here, we investigated morphological changes in fractal soot particles coated by sulfuric acid and then humidified, both in airborne and surface-bound states. Airborne soot was probed by tandem differential mobility analysis. Surface-bound soot was studied in a controlled microenvironment of a closed cell, using environmental transmission electron microscopy. After humidification, the airborne particles became fully compact, but the deposited particles showed only minor morphological changes despite significant water uptake. Although minor, those changes were detected during both water condensation and evaporation, indicating that condensation-evaporation cycles play an important role in atmospheric soot compaction. Lesser restructuring of deposited aggregates was caused by surface anchoring and coating loss, making anchoring an indispensable tool for preserving morphology of aggregates against changing experimental environment.

54 ENVIRONMENTAL SCIENCES↗

Soot formation and growth with palladium acetylacetonate-toluene injection in ethylene base flames investigated by in situ synchrotron small-angle X-ray scattering

Organo-Pd compounds as fuel additives are proven to have distinct catalytic effects on enhancing ignition and combustion performance. However, their effects on soot emission and the mechanism are not well-established. In this study, the effect of palladium acetylacetonate (Pd(C 5 H 7 O 2 ) 2 , Pd(acac) 2 ) on soot formation and growth was investigated experimentally. Different concentrations of Pd(acac)2 were added in the ethylene flames. Synchrotron small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM) were used to detect the soot particles to obtain the size, shape and morphology information. The results show that the Pd(acac) 2 addition with low concentration (100 ppm) suppresses the formation and growth of the primary soot particles at each height above the burner. As the addition concentration increases to 200 and 300 ppm, the size and volume fraction of the soot particles are decreased at the low flame region, and increased at the high flame region. Furthermore, detailed size distribution, morphology and nanostructure information of the soot particles at different flame heights are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Poly(oxymethylene) Ethers as a High Cetane, Low Sooting Biofuel Blendstock for Use in Medium to Heavy Duty Mixing Controlled Compression Ignition Engines

Compression ignition (CI) engines are currently the most common prime mover for medium and heavy duty vehicles; these engines contribute roughly a quarter of US greenhouse gas emissions from transportation, and even higher percentages of particulate and nitrogen oxide emissions. As a result, there have been significant efforts made to reduce these emissions, particularly through selection of low-emissions alternative fuels. Oxymethylene ethers (OMEs) are a class of molecule, typically structured R-O-(CH2O)n-R', which have been considered as a possible blendstock in CI fuels for the goal of soot reduction. Generally, past work has focused on methyl-terminated OMEs, CH3-O-(CH2O)n-CH3, which by virtue of containing no C--C bonds, produce negligible soot. These molecules show significant reductions in soot emission from engines when blended in moderate to high ratios with traditional diesels, however, they have been shown to have inferior physical properties and poor compatibility with some legacy systems. Recent theoretical work has shown that OMEs with non-methyl alkyl groups may have superior performance, albeit at the cost of increased soot formation. In this work, a variety of OMEs with terminating alkyl groups from methyl to butyl are considered for their suitability as CI fuels. The synthesis of these extended OMEs is studied, including formation of n=1 OMEs from common chemical sources, and extension of the chain length to heavier molecules, via reactions over acidic ion exchange resins. Following the synthesis, the properties of these OMEs are studied with respect to their engine applicability. It is found that heavier (propyl- and butyl-terminated) OMEs have superior properties for diesel compatibility, particularly in reactivity, volatility, and water solubility. Extended-alkyl OMEs are found to have higher soot production than methyl-terminated OMEs, but remain superior to diesel soot production on a per-unit-energy basis. A sample of a butyl-terminated OME mixture, n=2-4, is selected as the ideal OME blend for close compatibility with legacy diesel systems. This mixture is blended with certified diesel and tested for ASTM D975 compatibility, passing all required tests but lubricity; decreased heat of combustion is observed but not governed by the diesel standard. Fundamental combustion tests of various mid-weight OMEs are performed in a rapid compression machine, where it is shown that low-temperature chemistry causes a region of decreased dependence of ignition delay on temperature, consistent with methyl-terminated OME behavior. An isopropyl-terminated OME is observed to have low reactivity compared to other OMEs; this fuel is investigated via further rapid compression machine testing and CFR engine testing. It is found that this OME has strong negative-temperature-coefficient ignition behavior - a first for OMEs - and has reactivity lower than other OMEs, but insufficient for direct spark ignition engine testing.

09 BIOMASS FUELS↗

Investigating the Effects of Chemical Mechanism on Soot Formation Under High-Pressure Fuel Pyrolysis

We performed Computational Fluid Dynamics (CFD) simulations using a Reynolds-Averaged Navier-Stokes (RANS) turbulence model of high-pressure spray pyrolysis with a detailed chemical kinetic mechanism encompassing pyrolysis of n-dodecane and formation of polycyclic aromatic hydrocarbons. We compare the results using the detailed mechanism and those found using several different reduced chemical mechanisms to experiments carried out in an optically accessible, high-pressure, constant-volume combustion chamber. Three different soot models implemented in the CONVERGE CFD software are used: an empirical soot model, a method of moments, and a discrete sectional method. There is a large variation in the prediction of the soot between different combinations of chemical mechanisms and soot model. Furthermore, the amount of soot produced from all models is substantially less than experimental measurements. All of this indicates that there is still substantial work that needs to be done to arrive at simulations that can be relied on to accurately predict soot formation.

02 PETROLEUM↗

MODELING OF THERMOPHORETIC SOOT DEPOSITION ANDHYDROCARBON CONDENSATION IN EGR COOLERS

EGR coolers are effective to reduce NOx emissions from diesel engines due to lower intake charge temperature. EGR cooler fouling reduces heat transfer capacity of the cooler significantly and increases pressure drop across the cooler. Engine coolant provided at 40-90 C is used to cool EGR coolers. The presence of a cold surface in the cooler causes particulate soot deposition and hydrocarbon condensation. The experimental data also indicates that the fouling is mainly caused by soot and hydrocarbons. In this study, a 1-D model is extended to simulate particulate soot and hydrocarbon deposition on a concentric tube EGR cooler with a constant wall temperature. The soot deposition caused by thermophoresis phenomena is taken into account the model. Condensation of a wide range of hydrocarbon molecules are also modeled but the results show condensation of only heavy molecules at coolant temperature. Thermal properties of fouled layer are calculated based on mass fraction of deposited soot and hydrocarbons. The experiments with the same conditions ran to validate the model. Hot EGR gases flow through the inner pipe and the coolant circulates around it in the outer pipe to keep a constant wall temperature. Effectiveness, deposited soot mass, condensed hydrocarbon mass, and pressure drop across the cooler are the parameters that have been compared. The results of the model are in a reasonably good agreement with the experimental results although there are some fields that need to be studied in future to improve the model.

33 ADVANCED PROPULSION SYSTEMS↗

Chemical influence of ammonia on suppressing soot formation pathways

There is interest in mixing ammonia (NH3) with hydrocarbons, as this decreases overall CO2 emissions from the fuel mixture when burned. Co-firing NH3 with hydrocarbons like methane (CH4) also enables stable combustion over a larger set of operating conditions in engines and gas turbines than firing only NH3 permits. When NH3 is co-fired with hydrocarbons, the influence of NH3 on soot formation chemistry becomes relevant. In this work, soot concentrations in laminar nonpremixed co-flow flames of NH3/CH4 and N2/CH4 were analyzed using color-ratio pyrometry. The concentrations of combustion species (CH4, CO2, H2O, O2, C2H2, C6H6, HCN) across the different flames were also determined using on-line electron-impact mass spectrometry. The flames were also interrogated with 2D CFD simulations, which employ a detailed chemical mechanism tailored to capturing fuel-nitrogen chemistry. Addition of NH3 to CH4 flames was found to decrease soot concentrations more significantly than N2-addition (Fig. 1). The NH3/CH4 flames were found to have higher flame temperatures than the N2/CH4 flames, implying the suppression of soot afforded by NH3 is due to a chemical influence of NH3, as opposed to thermal or dilution effects. Based on experimental and simulated soot volume fractions and species concentrations, soot formation pathways affected by NH3 are postulated.

10 SYNTHETIC FUELS↗

A multi-probe thermophoretic soot sampling system for high-pressure diffusion flames

Optical diagnostics and physical probing of the soot processes in high pressure combustion pose challenges that are not faced in atmospheric flames. One of the preferred methods of studying soot in atmospheric flames is in situ thermophoretic sampling followed by transmission electron microscopy imaging and analysis for soot sizing and morphology. The application of this method of sampling to high pressures has been held back by various operational and mechanical problems. In this work, we describe a rotating disk multi-probe thermophoretic soot sampling system, driven by a microstepping stepper motor, fitted into a high-pressure chamber capable of producing sooting laminar diffusion flames up to 100 atm. Innovative aspects of the sampling system design include an easy and precise control of the sampling time down to 2.6 ms, avoidance of the drawbacks of the pneumatic drivers used in conventional thermophoretic sampling systems, and the capability to collect ten consecutive samples in a single experimental run. Proof of principle experiments were performed using this system in a laminar diffusion flame of methane, and primary soot diameter distributions at various pressures up to 10 atm were determined. High-speed images of the flame during thermophoretic sampling were recorded to assess the influence of probe intrusion on the flow field of the flame.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Predicting the Cetane Number, Sooting Tendency, and Energy Density of Terpene Fuel Additives

Abstract Discovering renewable fuels and fuel additives is paramount in reducing carbon emissions from internal combustion engines. Terpenes, a group of compounds that can be synthesized from plant matter and microorganisms, have gained significant interest in recent years as promising candidates for fuels/additives. Terpenes are a diverse class of compounds that contain rings and methyl branches, resulting in high energy densities and optimal cold weather behavior. Their variation in bond order, carbon chains, and functional groups lead to varying degrees of soot formation and performance in existing engines. The present work leverages predictive models, namely artificial neural networks, to predict the cetane number (CN), sooting tendency (quantified with yield sooting index, YSI), and energy density (quantified with lower heating value, LHV) of terpenes and hydrogenated terpenes whose sooting propensities were previously determined through experimental means. Predicted sooting propensities of these terpenes are compared with experimental values, and predicted cetane numbers and energy densities are used to comment on the compounds’ ability to act as fuels/additives. Expected prediction errors for CN, YSI, and LHV, defined by blind test set median absolute error, are within 5.56 cetane units, 3.63 yield sooting index units, and 0.77 MJ/kg respectively. Additionally, the present work investigates a variety of correlation/dependence metrics for property-property relationships, furthering our understanding of how combustion-relevant properties are related.

09 BIOMASS FUELS↗