Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SCANDIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Solid oxide fuel cell electrolytes produced by a combination of suspension plasma spray and very low pressure plasma spray.

Plasma spray coating techniques allow unique control of electrolyte microstructures and properties as well as facilitating deposition on complex surfaces. This can enable significantly improved solid oxide fuel cells (SOFCs), including non-planar designs. SOFCs are promising because they directly convert the oxidization of fuel into electrical energy. However, electrolytes deposited using conventional plasma spray are porous and often greater than 50 microns thick. One solution to form dense, thin electrolytes of ideal composition for SOFCs is to combine suspension plasma spray (SPS) with very low pressure plasma spray (VLPPS). Increased compositional control is achieved due to dissolved dopant compounds in the suspension that are incorporated into the coating during plasma spraying. Thus, it is possible to change the chemistry of the feed stock during deposition. In the work reported, suspensions of sub-micron diameter 8 mol.% Y2O3-ZrO2 (YSZ) powders were sprayed on NiO-YSZ anodes at Sandia National Laboratories (SNL) Thermal Spray Research Laboratory (TSRL). These coatings were compared to the same suspensions doped with scandium nitrate at 3 to 8 mol%. The pressure in the chamber was 2.4 torr and the plasma was formed from a combination of argon and hydrogen gases. The resultant electrolytes were well adhered to the anode substrates and were approximately 10 microns thick. The microstructure of the resultant electrolytes will be reported as well as the electrolyte performance as part of a SOFC system via potentiodynamic testing and impedance spectroscopy.

08 HYDROGEN↗

MATERIALS THAT SHRINK ON HEATING: PRESSURE-INDUCED PHASE TRANSITIONS IN NEGATIVE THERMAL EXPANSION MATERIALS, AND THEIR ENERGETICS

Despite the fact that all chemical bonds expand on heating, a small class of materials shrinks when heated. These, so called negative thermal expansion (NTE) materials, are a unique class of materials with some exotic properties. The present chapter offers insight into the structural aspects of pressure- (or temperature-) induced phase transformations, and the energetics of those changes in these fascinating materials, in particular NTE compound cubic ZrW2O8, orthorhombic Sc2W3O12 and Sc2Mo3O12, as well as other members of the 'scandium tungstate family'. In subsequent sections, (i) combined in situ high-pressure synchrotron XRD and XAS studies of NTE material ZrW2O8; (ii) an in situ high-pressure synchrotron XRD study of Sc2W3O12, Sc2Mo3O12, and Al2W3O12; and (iii) thermochemical studies of the above materials are presented and discussed. In all of these studies, chemical bonds change, sometimes break and new ones form. Correlations between structure, chemistry, and energetics are revealed. It is also shown that (iv) NTE materials are good candidates as precursors to make novel solid state materials, such as the conducting Sc0.67WO4, using high-pressure, high-temperature synthesis, through modification of bonding and electronic structure, and thus provide vast opportunities for scientific exploration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Unlocking AlN Piezoelectric Performance with Earth‐Abundant Dopants

Abstract The increasing demand for high‐performance piezoelectric materials and toxicity and thermal stability issues of the widely used lead zirconate titanates (PZT) have spurred a search for better alternatives in electronic devices. In comparison to PZT, group III nitrides such as aluminum nitride (AlN), are only weakly piezoelectric, but doping AlN with scandium (Sc) improves the piezoelectric response by nearly 500%. Relative to PZT, doped‐AlN piezoelectric materials are advantageous because they are far more compatible with complementary metal–oxide–semiconductor (CMOS) materials, and they maintain both piezoelectric and thermodynamic stability up to very high temperatures. Unfortunately, rare‐earth metals are notoriously expensive, and fabricating stable films with rare‐earth dopants is also challenging, limiting their use in industrial applications. In this work, ab initio calculations are combined with targeted fabrication and experimentation to identify alternative earth‐abundant dopants for AlN from the periodic table d‐block. Amongst the 23 elements screened, it is found that group IVB metals, titanium, zirconium, and hafnium induce large piezoelectric enhancements comparable to Sc. This improvement is traced to shifts in the atomic sublattice structure and changes in the local charge states. In demonstrating a highly accessible and affordable path for technological adaptation of AlN‐based piezoelectrics, this work provides the foundation for sustainable, next‐generation electronics.

Startt, Jacob↗

Interpretable Machine Learning Models for Practical Antimonate Electrocatalyst Performance

Computationally predicting the performance of catalysts under reaction conditions is a challenging task due to the complexity of catalytic surfaces and their evolution in situ, different reaction paths, and the presence of solid-liquid interfaces in the case of electrochemistry. We demonstrate here how relatively simple machine learning models can be found that enable prediction of experimentally observed onset potentials. Inputs to our model are comprised of data from the oxygen reduction reaction on non-precious transition-metal antimony oxide nanoparticulate catalysts with a combination of experimental conditions and computationally affordable bulk atomic and electronic structural descriptors from density functional theory simulations. From human-interpretable genetic programming models, we identify key experimental descriptors and key supplemental bulk electronic and atomic structural descriptors that govern trends in onset potentials for these oxides and deduce how these descriptors should be tuned to increase onset potentials. Here, we finally validate these machine learning predictions by experimentally confirming that scandium as a dopant in nickel antimony oxide leads to a desired onset potential increase. Macroscopic experimental factors are found to be crucially important descriptors to be considered for models of catalytic performance, highlighting the important role machine learning can play here even in the presence of small datasets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of epitaxial Al x Sc 1-x N for artificially structured metal/semiconductor superlattice metamaterials

Epitaxial nitride rocksalt metal/semiconductor superlattices are emerging as a novel class of artificially structured materials that have generated significant interest in recent years for their potential application in plasmonic and thermoelectric devices. Though most nitride metals are rocksalt, nitride semiconductors in general have hexagonal crystal structure. We report rocksalt aluminum scandium nitride (Al,Sc)N alloys as the semiconducting component in epitaxial rocksalt metal/semiconductor superlattices. The Al x Sc 1-x N alloys when deposited directly on MgO substrates are stabilized in a homogeneous rocksalt (single) phase when x < 0.51. Employing 20 nm TiN as a seed layer on MgO substrates, the homogeneity range for stabilizing the rocksalt phase has been extended to x < 0.82 for a 120 nm film. The rocksalt Al x Sc 1-x N alloys show moderate direct bandgap bowing with a bowing parameter, B = 1.41 ± 0.19 eV. The direct bandgap of metastable rocksalt AlN is extrapolated to be 4.70 ± 0.20 eV. The tunable lattice parameter, bandgap, dielectric permittivity, and electronic properties of rocksalt Al x Sc 1-x N alloys enable high quality epitaxial rocksalt metal/Al x Sc 1-x N superlattices with a wide range of accessible metamaterials properties.

36 MATERIALS SCIENCE↗

The Efficacy of Replacing Metallic Cerium in Aluminum–Cerium Alloys with LREE Mischmetal

The ongoing development of aluminum–cerium alloys has produced materials exhibiting elevated temperature mechanical property retention, long term microstructural stability, and flexible processability compared to traditional aluminum alloys, accommodating the growing demand for high temperature aluminum alloys not requiring the use of high-cost elements like scandium. To date, reported Al–Ce alloy compositions contain large amounts of elemental cerium. Mischmetal (MM), a mixture of lanthanum, cerium, and other light rare earth elements (LREE) is less expensive and more available than pure cerium. The chemical similarity of the LREEs means there is possibility to use MM as the primary alloy addition, lowering alloy cost. This talk will report the effect of using MM instead of cerium in a 12 wt% binary alloy on mechanical properties, phase constituency, thermal stability, and load sharing. Results will show that MM can be substituted completely for cerium with a mostly positive impact on alloy performance.

Sims, Zachary↗

Synthesis of N-Guanidinium-Chitosan/Silica Hybrid Composites: Efficient Adsorbents for Anionic Pollutants

A new chitosan derivative, N-guanidinium chitosan acetate, has been synthesized by direct guanylation of chitosan by cyanamide in presence of scandium(III) triflate under mild acidic condition. Starting from this material, N-guanidinium chitosan/silica microhybrids were prepared via a sol gel method using 3-glycidoxypropyl trimethoxysilane as silica precursor. Both N-guanidinium chitosan and the N-guanidinium chitosan/silica hybrid were characterized by a range of analytical techniques such as {sup 29}Si/{sup 13}C solid state NMR, FT-IR, scanning electron microscopy, thermogravimetry and elemental analysis. The characterization of the chitosan/silica hybrid indicated that this material is a highly hydrophilic nanocomposite material containing an organic core and a highly condensed silica shell. The N-guanidinium chitosan/silica microhybrids display excellent adsorption properties for anionic dyes such as methyl orange (MO) with very high capacities up to 917 mg/g. The fixation of MO as anionic dye was investigated in detail as a function of contact time, pH and the MO concentration. The adsorption kinetics of MO on N-guanidinium chitosan/silica microhybrids was more accurately described by pseudo second-order model. Langmuir isotherm model exhibited a better fit with adsorption data than Freundlich isotherm model. This work opens new possibilities for using N-guanidinium chitosan as a reusable adsorbent for water purification. Graphical Abstract: .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Role of Surface Termination in the Structural and Electronic Properties of Sc$_2$CT$_\textrm{x}$ MXene

Graphene-like layered transition metal carbides, nitrides, or carbonitrides, called MXenes, obey the stoichiometric formula of M n+1 X n T x , where M is an early transition metal such as scandium (Sc), n is a natural number, X is C, N, or CN, and T x is a functional group such as –O, –F, or –OH that passivates the surface of the MXene. The electronic structure of bare Sc 2 C and functionalized Sc 2 CT x MXenes are explored by performing first-principles density functional theory (DFT) calculations. The bare Sc 2 C is metallic, but less stable than its passivated structure. The Sc 2 C MXene has an interlayer 2D electron gas not bound to Sc or C atoms but free to move, making it an electride. DFT calculations show that functionalization can open an energy gap in Sc 2 CT x MXenes. The size and type (direct versus indirect) of the bandgap vary with the functional groups, which provides a means for opening and tuning of the band gap.

DFT↗

A Field Survey of Rare Earth Element Concentrations in Process Streams Produced by Coal Preparation Plants in the Eastern USA

I this work, a field study was undertaken to experimentally measure the concentrations of rare earth elements (REEs) contained in the process streams generated by a group of 20 coal preparation plants located in the eastern USA. For each site, representative samples of clean coal product, coarse refuse, and fine refuse were collected. Each sample was then partitioned into preselected size and density classes by wet screening/sieving and float-sink testing. The resultant products were dried and subjected to laboratory analyses to determine ash contents and rare earth element concentrations including Yttrium and Scandium. A detailed analysis of the database generated by this exercise showed that coal-based products from these preparation plants contained significant quantities of rare earth elements. In particular, the coarse refuse streams currently discarded by the 20 plants examined were found to contain a sufficient tonnage of REEs to satisfy the current domestic demand for these important elements. The data also showed a strong positive correlation between ash content and REE concentration, which suggested that the primary association of REEs in eastern USA bituminous coal sources is likely within fractions containing inorganic impurities. This association was well described using a simple power equation relating ash content and REE concentration. The ratio of heavy-to-light rare earth elements was discovered to be significantly higher in organically rich fractions of clean coal, suggesting that mineral impurities intimately associated with carbonaceous matter have elevated concentrations of heavy rare earth elements. A similar trend was observed for a grouping of rare earth elements (Y, Nd, Eu, Tb, and Dy) that are likely subject to near-term supply shortages. Finally, the database showed that a linear correlation existed between La for many REEs of interest, although there were several notable exceptions for some high-value REEs (Lu, Pr, and Tb).

01 COAL, LIGNITE, AND PEAT↗

Differentiating the bonding states in calcium carbonate polymorphs by low-loss electron-energy-loss spectroscopy

Calcium carbonate is one of the important building components in organisms, especially the two most common polymorphs, calcite and aragonite. Here, to understand the difference in bonding state, the two polymorphs are characterized by valence (low-loss) electron energy loss spectroscopy. It is found that the difference in Ca M 23 edge originating from 3p to 3d states is consistent with the change of Ca-O bonds in the two studied polymorphs. Surprisingly, the measured Ca M 23 edge is in qualitative agreement with the calculated partial density of states (PDOS) of Ca-d states in contrast to their L edges (from 2p to 3d states) which are strongly influenced by atomic multiplet effect (spin-orbit coupling). This is because the atomic multiplet effect is much reduced for the Ca 3p orbital, which permits the corresponding Ca M 23 edge to be compared with the PDOS results. Our findings show insights that PDOS can potentially be used to interpret the M 23 edge of lighter 3d transition metals such as scandium, titanium, vanadium and chromium when such interpretation may not be achieved for their L edges.

36 MATERIALS SCIENCE↗

Leaching Behavior of Rare Earth Elements in Fort Union Lignite Coals of North America

Rare earth elements are crucial materials in an incredible array of consumer goods, energy system components and military defense applications. However, the global production and entire value chain for rare earth elements is dominated by China, with the U.S. currently 100% import reliant for these critical materials. Traditional mineral ores including those previously mined in the U.S., however, have several challenges. Chief among these is that the content of the most critical and valuable of the rare earths are deficient, making mining uneconomical. Further, the supply of these most critical rare earths is nearly 100% produced in China from a single resource that is only projected to last another 10 to 20 years. The U.S. currently considers the rare earths market an issue of national security. It is imperative that alternative domestic sources of rare earths be identified and methods developed to produce them. Recently, coal and coal byproducts have been identified as one of these promising alternative resources. This paper details the results of a study on characterization of North Dakota lignite and lignite-related feedstocks as an assessment of their feasibility for rare earth element recovery. The abundance, distribution and modes of occurrence of the rare earth elements in the samples collected were determined in this initial study to inform the selection of appropriate extraction and concentration methods to recover the rare earth elements. Materials investigated include the lignite coals, clay-rich sediments associated with the coal seams, and materials associated with a lignite beneficiation system and power plant. The results show that high rare earth element levels exist both in lignite coals and associated sediments. The form of the rare earth elements in the clay materials is primarily as ultra-fine mineral grains. In the lignite coals, approximately 80-95% of the rare earths content is organically associated, primarily as coordination complexes.

Laudal, Daniel A.↗

Distribution of rare earth and other critical elements in lignites from the Eocene Jackson Group, Texas

Coal is increasingly evaluated as a source of rare earth elements (REEs) in the United States to address the overreliance on imported REEs. The objective of this study was to assess the distribution of REEs in lignites from selected mining areas in the Texas Gulf Coastal Plain region. Thirty-one archived lignite and rock samples previously collected by the U.S. Geological Survey were analyzed for their rare earth element and critical mineral content. These include samples from one core (5400 and 5500 lignite horizons) and two opencast lignite mines (Gibbons Creek 3500 and 4500 horizons, and San Miguel horizons A to D) in the Eocene Jackson Group of the Texas Gulf of Mexico Coastal Plain. Some lithologies in the Gibbons Creek 3500 and 4500 lignite-bearing sections have high total rare earth, yttrium (Y), and scandium (Sc) (REYSc) values, up to 7800 ppm (ash basis) REYSc. The lignite lithologies show an enrichment in rare earths, [samarium (Sm) through gadolinium (Gd)]. The basal Gibbons Creek 3500 lignite bench shows a heavy rare earth element enrichment pattern resembling that often seen in peats through high volatile A bituminous coals. The 5500 lignite sequence, overlying the latter lignite sections, shows a light rare earth enrichment. The San Miguel lignite benches have heavy rare earth enrichments with a negative europium (Eu) anomaly.

58 GEOSCIENCES↗

Assessing Mg–Sc–(rare earth) ternary phase stability via constituent binary cluster expansions

The disordered Mg–Sc body-centered cubic (bcc) phase is both lightweight and strong; however, the system is impractical for general industrial use due to the high cost of scandium. Here we propose a computationally efficient metric that assesses ternary rare earth element additions that may stabilize the bcc phase at lower Sc concentrations. We find that the bcc phase is stabilized by the ternary addition of Y or Er, but not by La, Ce, or Nd, and we validate these predictions by experimental production and characterization of Mg–Sc–(Y,Er,Nd) alloys. The results suggest a computationally efficient method to anticipate integration of ternary elements into binary systems using cluster expansions of constituent binaries.

36 MATERIALS SCIENCE↗

Calcination pretreatment effects on acid leaching characteristics of rare earth elements from middlings and coarse refuse material associated with a bituminous coal source

The pretreatment of middlings and coarse refuse material collected from a Pocahontas No.3 coal source using calcination was investigated for the potential of improving the leaching recovery of rare earth elements. Calcination at 600 °C significantly and preferentially improved light REE (LREE) recovery to values in the range of 80-90% using 1.2 M HCl. The positive effect was due to the increased pore diameter and volume as well as thermal decomposition of the minerals associated with the LREEs. Heavy REE recovery was not increased after calcination at 600 °C due to the need for higher temperatures for the thermal decomposition of HREE minerals. Furthermore, some HREEs were also associated with sulfide minerals (e.g., pyrite) which were transformed into low-solubility oxides (e.g., hematite) after roasting at 600 °C. Based on the leaching characteristics of the major elements (Fe, Al, Ca and Mg) and REEs along with SEM EDX data, it was concluded that REEs in the two samples mainly occurred as phosphate minerals. In the middlings, some of the minerals were completely encapsulated by kaolinite, which was less apparent in the coarse refuse. In addition, it was found that a portion of the REEs (10-25%) in the samples were associated with micro-dispersed material in the organic matrix and was released after calcination and easily recovered using 0.1M (NH 4 ) 2 SO 4 solution at pH 5. In conclusion, Scandium primarily occurred in mineral forms with minimum amounts associated with ion-adsorbed clays and organic association.

01 COAL, LIGNITE, AND PEAT↗

Microstructural changes in NiO–ScSZ composite following reduction processes in pure and diluted hydrogen

A Ni–ScSZ cermet is widely used as the anode in a solid oxide fuel cell because it possesses the appropriate electrochemical properties. However, it is susceptible to degradation during operation. Samples of a NiO–ScSZ composite were reduced in pure and diluted hydrogen to determine the microstructural evolution and the degradation behavior of the material. The resulting changes in microstructure were investigated using scanning transmission electron microscopy, X-ray energy dispersive spectroscopy and electron energy loss spectroscopy. The resulting data revealed that the various conditions during the reduction processes had a significant effect on the microstructures. The high porosity of the reduced nickel phase and cracking between the Ni and the ZrO{sub 2} phases after reduction resulted in a reduction in the strength of the anode material. - Highlights: • Structure of NiO/Ni strongly depends on the concentration of reduction atmosphere • Scandium rich precipitations are visible in YSZ phase after reduction process • Nanopores and nanograins are formed in reduced Ni phase.

36 MATERIALS SCIENCE↗

Solute diffusion behavior during heat treatment and its impact in Sc-microalloyed Al-Cu system

Scandium (Sc) is a promising microalloying element that enhances the strength and thermal stability of aluminum (Al) alloys. However, these benefits are not fully realized in aluminum-copper (Al-Cu) systems, and corrosion resistance often declines due to the complex phase evolution and diffusion behavior of Cu and Sc. Here, to clarify this, solute diffusion behavior and Cu-Sc interaction during heat treatment (HT) were investigated using in situ synchrotron-based transmission x-ray microscopy (TXM), wide-angle x-ray scattering (WAXS), and x-ray absorption near-edge structure (XANES) spectroscopy. The results, supported by electron microscopy, reveal strong Cu-Sc bonding that significantly impedes solute diffusion, leading to inhomogeneous solute distribution and non-uniform precipitation. Moreover, the Al-Cu-Sc eutectic phase exhibits high thermal stability, resisting dissolution even near the matrix liquidus. These findings quantitatively elucidate the sluggish diffusion kinetics of Cu and Sc, which can help redesign HT schedules to improve both mechanical properties and corrosion resistance in Sc-microalloyed Al-Cu alloys.

36 MATERIALS SCIENCE↗

Hydrated doped-BaZrO 3 proton conductors studied by positron annihilation lifetime spectroscopy

The study of defect chemistry for doped BaZrO 3 proton conductors is of particular interest because of defect interactions that can affect the proton conductivity of the material. Protons incorporated due to the material's hydration can be trapped by negatively charged immobile dopants, reducing proton mobility. The reduction of the proton conduction impedes using BaZrO 3 materials in energy conversion applications at intermediate temperatures (300°C – 600°C). The probing of proton trapping in doped BaZrO 3 is hindered by the limited availability of techniques sensitive to defect chemistries. In this work, we used positron annihilation lifetime spectroscopy (PALS) to study the defect chemistry of Y-doped and Sc-doped BaZrO 3 . Using a two-state positron trapping model we showed that PALS can be used to study the defect chemistry of hydrated dense proton conductors. Positron trapping rates and lifetimes were correlated with doping levels of the materials. Probability significance t-tests were carried out for PALS parameters to verify whether there are differences/similarities for various populations: non-doped/doped, level and type of doping, high temperature, and surface effects. Further, the results revealed that the initial doping generates a significant number of traps available for positrons. Doping in yttrium increased the positron trapping rate, while this effect was not observed with scandium. Low-temperature hydration affects specimens significantly inhibiting positron trapping at undoped BaZrO 3 material and highly doped specimens. Positronium formation in rough surface layers, and highly doped specimens was detected but does not exceed 1%.

36 MATERIALS SCIENCE↗

Thickness dependence of Al 0.88 Sc 0.12 N thin films grown on silicon

The thickening behavior of aluminum scandium nitride (Al 0.88 Sc 0.12 N) films grown on Si(111) substrates has been investigated experimentally using X-ray diffraction (XRD), transmission electron microscopy (TEM), atomic force microscopy, and residual stress measurement. Al 0.88 Sc 0.12 N films were grown with thicknesses spanning 14 nm to 1.1 um. TEM analysis shows that the argon sputter etch used to remove the native oxide prior to deposition produced an amorphous, oxygen-rich surface, preventing epitaxial growth. XRD analysis of the films show that the A1ScN(002) orientation improves as the films thicken and the XRD A1ScN(002) rocking curve full width half maximum decreases to 1.34 q for the 1.1 pm thick film. XRD analysis shows that the unit cell is expanded in both the a- and c-axes by Sc doping; the a-axis lattice parameter was measured to be 3.172 ± 0.007 A and the c-axis lattice parameter was measured to be 5.000 ± 0.001 A, representing 1.96% and 0.44% expansions over aluminum nitride lattice parameters, respectively. The grain size and roughness increase as the film thickness increases. A stress gradient forms through the film; the residual stress grows more tensile as the film thickens, from -1.24 GPa to +8.5MPa.

36 MATERIALS SCIENCE↗