SEARCH · Engineering Papers

Results for “SAFETY MARGINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Wing contamination - Threat to safe flight

Attention is given to the initial results of systematic investigations of the potentially hazardous effect of heavy rain, ice, and frost accretion on aircraft wings. In the laminar region of an airfoil, roughness interferes with smooth flow and tends to encourage transition from laminar to turbulent flow upstream of its normal point of occurrence. In the airfoil's turbulent region, roughness considerably worsens the turbulent friction coefficient, thereby increasing the drag coefficient. Consequent dramatic decreases of maximum lift coefficient at high angles of attack lead to premature stall. Such decreases in stall angle destroy the safety margin of an aircraft approaching stall. An assessment is given to the state of knowledge in this field of research.

Luers, J. K.↗

NASA NTRS1986

Stability investigation of the quadripod structure for the NASA/JPL 70-meter antenna

A new, slim-profiled, low-blockage quadripod structure was designed to support the 7.7-m-diameter subreflector for the 70-m antenna. Detailed analyses of quadripod structural stability (in frequency and buckling) are presented. The results indicate that the new quadripod design has an adequate safety margin for buckling, and its lowest natural frequency is above the control system bandwidth. The analytical design frequencies were confirmed by actual field measurements made in Spain in February 1986.

Chian, C. T.↗

NASA NTRS1987

Buckling analysis of the quadripod structure for the NASA 70-meter antenna

As part of the effort to extend the diameter of three Deep Space Network large earth antennas from 64 meters to 70 meters, a slim profiled quadripod structure was designed to support a 7.7 meter diameter subreflector for the 70 meter antenna. The new quadripod design, which particularly emphasizes reduced radio frequency blockage, is achieved by means of a narrow cross sectional profile of the legs. Buckling analysis, using NASTRAN, was conducted in this study to verify the safety margin for the quadripod structural stability.

Chian, Chian T.↗

NASA NTRS1987

Propfan test assessment testbed aircraft flutter model test report

The PropFan Test Assessment (PTA) program includes flight tests of a propfan power plant mounted on the left wind of a modified Gulfstream II testbed aircraft. A static balance boom is mounted on the right wing tip for lateral balance. Flutter analyses indicate that these installations reduce the wing flutter stabilizing speed and that torsional stiffening and the installation of a flutter stabilizing tip boom are required on the left wing for adequate flutter safety margins. Wind tunnel tests of a 1/9th scale high speed flutter model of the testbed aircraft were conducted. The test program included the design, fabrication, and testing of the flutter model and the correlation of the flutter test data with analysis results. Excellent correlations with the test data were achieved in posttest flutter analysis using actual model properties. It was concluded that the flutter analysis method used was capable of accurate flutter predictions for both the (symmetric) twin propfan configuration and the (unsymmetric) single propfan configuration. The flutter analysis also revealed that the differences between the tested model configurations and the current aircraft design caused the (scaled) model flutter speed to be significantly higher than that of the aircraft, at least for the single propfan configuration without a flutter boom. Verification of the aircraft final design should, therefore, be based on flutter predictions made with the test validated analysis methods.

Jenness, C. M. J.↗

NASA NTRS1987

Comparison of measured temperatures, thermal stresses and creep residues with predictions on a built-up titanium structure

Temperature, thermal stresses, and residual creep stresses were studied by comparing laboratory values measured on a built-up titanium structure with values calculated from finite-element models. Several such models were used to examine the relationship between computational thermal stresses and thermal stresses measured on a built-up structure. Element suitability, element density, and computational temperature discrepancies were studied to determine their impact on measured and calculated thermal stress. The optimum number of elements is established from a balance between element density and suitable safety margins, such that the answer is acceptably safe yet is economical from a computational viewpoint. It is noted that situations exist where relatively small excursions of calculated temperatures from measured values result in far more than proportional increases in thermal stress values. Measured residual stresses due to creep significantly exceeded the values computed by the piecewise linear elastic strain analogy approach. The most important element in the computation is the correct definition of the creep law. Computational methodology advances in predicting residual stresses due to creep require significantly more viscoelastic material characterization.

Jenkins, Jerald M.↗

NASA NTRS1988

Orbiter environment at S- and Ku-band frequencies

Detailed measurements of the electric field strength associated with the Ku-band radar and S-band communication link were made by the Plasma Diagnostics Package (PDP) on STS 51F. These measurements were made while the PDP was attached to the Remote Manipulation System arm and again while the PDP was released as a subsatellite. The results indicate that cargo elements that remain inside of the scan limits of the radar should experience fields less than 2 V/m and that elements that may encounter the main beam can use 300 V/m as a design guideline with adequate safety margin. S-band fields tended to be several dB lower than worst-case predictions. Safe design practice indicates that an electric field E = 100/r (r in meters) should be used as a guideline for deployable systems. S-band electric fields within the cargo bay envelope should be less than 2 V/m even with edge diffraction effects and reflections from other payloads taken into account. The absolute accuracy of these measurements is about 2 dB.

Murphy, G. B.↗

NASA NTRS1988

Spacecraft flight simulation: A human factors investigation into the man-machine interface between an astronaut and a spacecraft performing docking maneuvers and other proximity operations

The anticipated increase in rendezvous and docking activities in the various space programs in the Space Station era necessitates a renewed interest in manual docking procedures. Ten test subjects participated in computer simulated docking missions in which the influence of initial velocity was examined. All missions started from a resting position of 304.8 meters (1000 feet) along the space station's +V-bar axis. Test subjects controlled their vehicle with a translational hand controller and digital auto pilot which are both virtually identical to their space shuttle counterparts. While the 0.1 percent rule (range rate is equal to 0.1 percent of the range) used by space shuttle pilots is comfortably safe, it is revealed to be extremely inefficient in terms of time and not justifiable in terms of marginal safety. Time is worth money, not only because of training and launch costs, but because the sooner a pilot and spacecraft return from a mission, the sooner they can begin the next one. Inexperienced test subjects reduced the costs of simulated docking by close to a factor of 2 and achieved safe dockings in less than 4 percent of the time the baseline approach would entail. This reduction in time can be used to save lives in the event of an accident on orbit, and can tremendously reduce docking costs if fuel is produced from waste water on orbit.

Brody, Adam R.↗

NASA NTRS1990

SPOT 4 space magnetic recorder mechanisms

The design of the SPOT 4 satellite will be quite different from the previous ones. The design of the new magnetic tape recorder, which was derived from industrial knowledge and mission requirements; the main technical characteristics of the recorder; and the mechanical subsystems of the recorder and their locations and contributions to the final performance are all discussed. The philosophy of the development program, required to achieve the desired performance and reliability for each flight model, is described, and information on the schedule and current development is presented. The components of the tape plate system, (the transmission belts, tape rollers of the recorders, and reel hub ball bearings) which are subjected to heavy mechanical operation, fatigue, and wear in the thermal environment of the mission, are discussed. For each of the components, a description of its function in the recorder is given, as well as the mechanical stress imposed during the various operational phases. The quality testing program, which was used to verify the design safety margins, is described. Finally, the first test results of a functioning model of the flight system are presented.

Borrien, A.↗

NASA NTRS1991

An airborne FLIR detection and warning system for low altitude wind shear

It is shown through some preliminary flight measurement research that a forward looking infrared radiometer (FLIR) system can be used to successfully detect the cool downdraft of downbursts (microbusts/macrobursts) and thunderstorm gust front outflows that are responsible for most of the low altitude wind shear (LAWS) events. The FLIR system provides a much greater safety margin for the pilot than that provided by reactive designs such as inertial air speed systems. Preliminary results indicate that an advanced airborne FLIR system could provide the pilot with remote indication of microburst (MB) hazards along the flight path ahead of the aircraft. Results of a flight test of a prototype FLIR system show that a minimum warning time of one to four minutes (5 to 10 km), depending on aircraft speed, is available to the pilot prior to the microburst encounter.

Sinclair, Peter C.↗

NASA NTRS1991

Protection of electrical and electronic equipment against lightning indirect effects on the Airbus A340 wing

The provisions applied to the Airbus A340 wing wiring against lightning indirect effects are presented. The construction and installation of the wiring's shielding systems are described, and the analysis and tests performed to determine the effectiveness of the measures taken are discussed. A first evaluation of the results of the theoretical analysis together with the provisional results of tests indicate a sufficient safety margin between required and achieved protection levels.

Spiller, Olaf↗

NASA NTRS1990

Manifest - Payloads and accommodations

Developing a long-range manifest begins with the assessment of flight rate capability for the next 6 years. Payloads priorities, launch readiness, and service needs are reviewed and compatible mixed cargo flights are determined and integrated with the dedicated missions to become the manifest. Manifest development must also address Orbiter upgrades to assure that payload-related enhancements meet need dates and that new hardware integration does not adversely affect flight rate capability. A series of Space Shuttle upgrades and new capabilities are in development driven by a continuing effort to improve safety margins, support recognized payload needs, and unique SSF requirements. These enhancements include extended mission duration capability, ASRM development, extended middeck payload support capability, and improved attitude control systems.

Hedin, Dan↗

NASA NTRS1991

Multi-reactor power system configurations for multimegawatt nuclear electric propulsion

A modular, multi-reactor power system and vehicle configuration for piloted nuclear electric propulsion (NEP) missions to Mars is presented. Such a design could provide enhanced system and mission reliability, allowing a comfortable safety margin for early manned flights, and would allow a range of piloted and cargo missions to be performed with a single power system design. Early use of common power modules for cargo missions would also provide progressive flight experience and validation of standardized systems for use in later piloted applications. System and mission analysis are presented to compare single and multi-reactor configurations for piloted Mars missions. A conceptual design for the Hydra modular multi-reactor NEP vehicle is presented.

George, Jeffrey A.↗

NASA NTRS1989

Advanced Solid Rocket Motor (ASRM)

The principal phases and the current status of the ASRM program studies are briefly reviewed. The 150-in. diameter ASRM segmented motor design incorporates substantive changes to improve the reliability and design safety margins of the Space Shuttle system. The motor thrust characteristics are tailored to preclude the necessity for throttling the Space Shuttle Main Engines during the period of maximum dynamic pressure, thus reducing or eliminating about 175 criticality 1/1R failure modes of the shuttle system. The ASRM is designed to provide a 12,000-pound payload improvement to support Space Station development and other critical NASA missions. The first ASRM Shuttle development flight is tentatively scheduled for late 1994.

Jones, Kenneth W.↗

NASA NTRS1993

The Mini-Mast CSI testbed: Lessons learned

The Mini-Mast testbed was one of the first large scale Controls-Structure-Interaction (CSI) systems used to evaluate state-of-the-art methodology in flexible structure control. Now that all the testing at Langley Research Center has been completed, a look back is warranted to evaluate the program. This paper describes some of the experiences and technology development studies by NASA, university, and industry investigators. Lessons learned are presented from three categories: the testbed development, control methods, and the operation of a guest investigator program. It is shown how structural safety margins provided a realistic environment to simulate on-orbit CSI research, even though they also reduced the research flexibility afforded to investigators. The limited dynamic coupling between the bending and torsion modes of the cantilevered test article resulted in highly successful SISO and MIMO controllers. However, until accurate models were obtained for the torque wheel actuators, sensors, filters, and the structure itself, most controllers were unstable. Controls research from this testbed should be applicable to cantilevered appendages of future large space structures.

Tanner, Sharon E.↗

NASA NTRS1994

Probabilistic progressive buckling of trusses

A three-bay, space, cantilever truss is probabilistically evaluated to describe progressive buckling and truss collapse in view of the numerous uncertainties associated with the structural, material, and load variables that describe the truss. Initially, the truss is deterministically analyzed for member forces, and members in which the axial force exceeds the Euler buckling load are identified. These members are then discretized with several intermediate nodes, and a probabilistic buckling analysis is performed on the truss to obtain its probabilistic buckling loads and the respective mode shapes. Furthermore, sensitivities associated with the uncertainties in the primitive variables are investigated, margin of safety values for the truss are determined, and truss end node displacements are noted. These steps are repeated by sequentially removing buckled members until onset of truss collapse is reached. Results show that this procedure yields an optimum truss configuration for a given loading and for a specified reliability.

PROBABILISTIC BUCKLING ANALYSI↗

NASA NTRS1992

Radiation health for a Mars mission

Uncertainties in risk assessments for exposure of a Mars mission crew to space radiation place limitations on mission design and operation. Large shielding penalties are imposed in order to obtain acceptable safety margins. Galactic cosmic rays (GCR) and solar particle events (SPE) are the major concern. A warning system and 'safe-haven' are needed to protect the crew from large SPE which produce lethal doses. A model developed at NASA Johnson Space Center (JSC) to describe solar modulation of GCR intensities reduces that uncertainty to less than 10 percent. Radiation transport models used to design spacecraft shielding have large uncertainties in nuclear fragmentation cross sections for GCR which interact with spacecraft materials. Planned space measurements of linear energy transfer (LET) spectra behind various shielding thicknesses will reduce uncertainties in dose-versus-shielding thickness relationships to 5-10 percent. The largest remaining uncertainty is in biological effects of space radiation. Data on effects of energetic ions in human are nonexistent. Experimental research on effects in animals and cell is needed to allow extrapolation to the risk of carcinogenesis in humans.

Robbins, Donald E.↗

NASA NTRS1995

Aircraft control in wake vortex wind shear

In the past, there have been a number of fatal incidents attributable to wake vortex encounters, involving both general aviation and commercial aircraft. In fact, the wake vortex hazard is considered to be the single dominant safety issue determining the aircraft spacing requirements at airports. As the amount of air traffic increases, the number of dangerous encounters is likely only to increase. It is therefore imperative that a means be found to reduce the danger. That is the purpose of this research: to use nonlinear inverse dynamic (NID) control methods in the design of an aircraft control system which can improve the safety margin in a wake vortex encounter.

Wold, Gregory R.↗

NASA NTRS1996

Implementation of Probabilistic Design Methodology at Tennessee State University

Engineering Design is one of the most important areas in engineering education. Deterministic Design Methodology (DDM) is the only design method that is taught in most engineering schools. This method does not give a direct account of uncertainties in design parameters. Hence, it is impossible to quantify the uncertainties in the response and the actual safety margin remains unknown. The desire for a design methodology tha can identify the primitive (random) variables that affect the structural behavior has led to a growing interest on Probabilistic Design Methodology (PDM). This method is gaining more recognition in industries than in educational institutions. Some of the reasons for the limited use of the PDM at the moment are that many are unaware of its potentials, and most of the software developed for PDM are very recent. The central goal of the PDM project at Tennessee State University is to introduce engineering students to the method. The students participating in the project learn about PDM and the computer codes that are available to the design engineer. The software being used of this project is NESSUS (Numerical Evaluation of Stochastic Structures Under Stress) developed under NASA probabilistic structural analysis program. NESSUS has three different modules which make it a very comprehensive computer code for PDM. A research in technology transfer through course offering in PDM is in effect a Tennessee State University. The aim is to familiarize students with the problem of uncertainties in engineering design. Included in the paper are some projects on PDM carried out by some students and faculty. The areas this method is being applied at the moment include, Design of Gears (spur and worm); Design of Shafts; Design of Statistically Indeterminate Frame Structures; Design of Helical Springs; and Design of Shock Absorbers. Some of the current results of these projects are presented.

Onwubiko, Chinyere↗