Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rotor Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Rotor dynamic behaviour of a high-speed oil-free motor compressor with a rigid coupling supported on four radial magnetic bearings

The combination of a high-speed motor, dry gas seals, and magnetic bearings realized in this unit facilitates the elimination of oil. The motor is coupled with a quill shaft to the compressor. This yields higher natural frequencies of the rotor than with the use of a diaphragm coupling and helps to maintain a sufficient margin of the maximum speed to the frequency of the second compressor bending mode. However, the controller of each bearing then has to take the combined modes of both machines into account. The requirements for the controller to ensure stability and sufficient damping of all critical speeds are designed and compared with the implemented controller. The calculated closed loop behavior was confirmed experimentally, except the stability of some higher modes due to slight frequency deviations of the rotor model to the actual rotor. The influence of a mechanical damper as a device to provide additional damping to high models is demonstrated theoretically. After all, it was not necessary to install the damper, since all modes cold be stabilized by the controller.

Schmied, J.↗
NASA NTRS2006

Flight Acoustic Testing and Data Acquisition For the Rotor Noise Model (RNM)

Two acoustic flight tests have been conducted on a remote test range at Eglin Air Force Base in the panhandle of Florida. The first was the Acoustics Week flight test conducted in September 2003. The second was the NASA Heavy Lift Rotorcraft Acoustics Flight Test conducted in October-November 2005. Benchmark acoustic databases were obtained for a number of rotorcraft and limited fixed wing vehicles for a variety of flight conditions. The databases are important for validation of acoustic prediction programs such as the Rotorcraft Noise Model (RNM), as well as for the development of low noise flight procedures and for environmental impact assessments. An overview of RNM capabilities and a detailed description of the RNM/ART (Acoustic Repropagation Technique) process are presented. The RNM/ART process is demonstrated using measured acoustic data for the MD600N. The RNM predictions for a level flyover speed sweep show the highest SEL noise levels on the flight track centerline occurred at the slowest vehicle speeds. At these slower speeds, broadband noise content is elevated compared to noise levels obtained at the higher speeds. A descent angle sweep shows that, in general, ground noise levels increased with increasing descent rates. Vehicle orientation in addition to vehicle position was found to significantly affect the RNM/ART creation of source noise semi-spheres for vehicles with highly directional noise characteristics and only mildly affect those with weak acoustic directionality. Based on these findings, modifications are proposed for RNM/ART to more accurately define vehicle and rotor orientation.

Conner, David A.↗
NASA NTRS1978

Aerodynamic characteristics of a counter-rotating, coaxial, hingeless rotor helicopter model with auxiliary propulsion

A wind-tunnel model test at advance ratios from 0 to 0.3 with and without auxiliary jet engine thrust is reported. At each advance ratio and engine thrust, both the control power and the aircraft stability were measured. The results indicate that there is a cross-coupling for collective pitch and longitudinal cyclic pitch inputs. The control power for these inputs increased with advance ratio. There was also cross-coupling for differential collective pitch inputs. The airframe was longitudinally unstable, but the instability was less at the highest advance ratio tested. The airframe showed both positive effective dihedral and positive directional stability.

Phelps, A. E., III↗
NASA NTRS1984

Measured and calculated inplane stability characteristics for an advanced bearingless main rotor

A program of experimental and analytical research has been performed to demonstrate the effects of rotor and fuselage design parameters on rotor in-plane stability, including aeromechanical stability. The experimental data were obtained from hover and wind-tunnel tests of a scaled advanced bearingless main rotor model. Both isolated-rotor and free-hub conditions were tested. Test parameters included blade built-in cone and sweep angles; rotor inplane structural stiffness and damping; pitch link stiffness and location; and fuselage natural frequency, damping, and inertia. The results show that rotor blade structural damping is one of the most influential design parameters in obtaining acceptable aeromechanical stability margins. Other parameters, such as blade cone angle, pitch link location (rotor delta 3) and anisotropic hub damper configurations, may be used to improve stability margins, but their individual effects are subtle.

Weller, W. H.↗
NASA NTRS1984

Hovering model helicopter rotor testing

A relatively large test chamber, chosen to minimize room interference effects during helicopter hovering rotor tests, was found in initial operations to exhibit large, random variations of thrust, torque, and blade flapping. The source of these problems, unsteady recirculation of test chamber flow, was addressed by the addition of a 'flow straightener' that reduced these parameter variations to 1.5 percent of mean values. Rotor performance was then measured outside the chamber in calm, free air conditions and compared with chamber results obtained before and after modifications. Attention is given to wake flow visualization conducted in the test chamber, as well as outside.

Piziali, R. A.↗
NASA NTRS1986

Numerical modeling of rotor flows with a conservative form of the full-potential equations

A computer program has been developed to solve a three-dimensional conservative formulation of the full-potential equation. Its ability to solve transonic, unsteady rotor flows is demonstrated by comparison to forward flight non-lifting pressure data at low to moderate advance ratios. A 'split potential' formulation has been added to the code which incorporates known vorticity fields into the full-potential calculation. Using this methodology, rotor wake contributions have been incorporated into the computer code. Pressure results are presented for lifting rotors in hover. These results are compared to experimental data as well as to other predictions.

Strawn, R. C.↗
NASA NTRS1987

Comparing Test Data on Scale-Model Helicopter Rotors

Hovering data correlate well, but forward-flight data do not. Report compares acoustics and performance of small-scale helicopter rotor with those of full-scale rotor in both hovering and forward flight.

Kitaplioglu, Cahit↗
NASA NTRS1988

Acoustical Tests Of A Scale-Model Helicopter Rotor

Data obtained in simulated hovering flight in open environment. Report discusses measurements of sound generated in outdoor hoovering tests of 1/6-scale, four bladed helicopter rotor. Information of delineation between accoustic near field and far field and on effect of simple boundary-layer-tripping device. Also covers rotor accoustics at low thrust and at high thrust.

Kitaplioglu, Cahit↗