Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Recycling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

The Low-Recycling Lithium Boundary and Implications for Plasma Transport

Pumping of incident hydrogen and impurity ions by lithium enables control of the particle inventory and fueling profile in magnetic-confined plasmas, and may raise the plasma temperature near the wall. As a result, the density gradient is expected to contribute substantially to the free-energy, affecting particle and thermal transport from micro-turbulence which is typically the dominant transport mechanism in high-temperature fusion experiments. Transport in gyrokinetic simulations of density-gradient-dominated profiles is characterized by a small linear critical gradient, large particle flux, and preferential diffusion of cold particles. As a result, the heat flux is below 5/2 or even 3/2 times the particle flux, usually assumed to be the minimum for convection. While surprising, this result is consistent with increasing entropy. Coupled TEM-ITG (ion-temperature- gradient) simulations using ηe = ηi find η = ∇T /∇n∼0.8 maximizes the linear critical pressure gradient, which suggests that experiments operating near marginal ITG stability with larger η would increase the linear critical pressure gradient by transferring free-energy from the temperature gradient to the density gradient. Simulations were performed with profiles predicted for the Lithium Tokamak Experiment (LTX) if ion thermal transport was neoclassical, while electron thermal transport and particle transport were a fixed ratio above the neoclassical level. A robust TEM instability was found for the outer half radius, while the ITG was found to be driven unstable as well during gas puff fueling. This suggests that TEM transport will be an important transport mechanism in high-temperature low-recycling fusion experiments, and in the absence of stabilizing mechanisms, may dominate over neoclassical transport. A diagnostic suite has been developed to measure hydrogen and impurity emission in LTX in order to determine the lower bound on recycling that can be achieved in a small tokamak using solid lithium coatings, assess its dependence on the operating condition of the lithium surface, and evaluate its impact on the discharge. Coatings on the close-fitting stainless-steel substrate produce a significant reduction in recyling, so that the effective particle confinement times are as low as 1 ms. Measurements of particle inventory in the plasma and hydrogen Lyman-α emission indicate that hydrogen recycling at the surface increases as subsequent discharges are performed; nevertheless, strong pumping of hydrogen is observed even after almost double the cumulative fueling is applied that should saturate the lithium coating to the penetration depth of hydrogen ions. Probe measurements show that when external fueling is terminated, the scrape-off-layer of discharges with fresh coatings decays to lower density and rises to higher electron temperature than for discharges with a partially-passivated surface, consistent with reduced edge cooling from recycled particles. Near the end of the discharge, higher plasma current correlates with reduced τp * and hydrogen emission, suggesting that discharges with fresh coatings achieve higher electron temperature in the core. A novel approach using neutral modeling was developed for the inverse problem of determining the distribution of recycled particle flux from PFC surfaces given a large number of emission measurements, revealing that extremely low levels of recycling (Rcore∼0.6 and Rplate∼0.8) have been achieved with solid lithium coatings. Together with impurity emission measurements, modeling suggests that during periods of particularly low electron density, influx of impurities from the walls contributes substantially to the global particle balance.

magnetic confinement↗

Environmental and Economic Implications of Emerging Plastic Recycling Technologies

Recycling will play a crucial role in mitigating plastic pollution and promoting a circular economy for polymers. Quantitative analysis can help guide the optimization and implementation of these plastic management strategies, enabling increased circularity while minimizing costs, energy use, greenhouse gas emissions, and other environmental impacts. This talk will outline the Bio-Optimized Technologies to keep Thermoplastics out of Landfills and the Environment (BOTTLE) Consortium's approach to analysis-guided plastic recycling research. Stringent process modelling, life cycle assessment, and techno-economic analysis are used to benchmark the technical feasibility, environmental impacts, and costs of chemical and biological recycling technologies in comparison to conventional fossil fuel-based plastic manufacturing. Across emerging recycling strategies, several key challenges become apparent - including plastic feedstock pretreatment requirements, high energy or chemical use, and recycled plastic yields and quality - highlighting opportunities for future innovation. Through this consistent and in-depth analysis approach, BOTTLE aims to provide the plastics community with key metrics and insights to drive plastic recycling innovation towards a more sustainable and circular economy.

circular economy↗

PWR core design, neutronics evaluation and fuel cycle analysis for thorium-uranium breeding recycle

This paper was focused on core design, neutronics evaluation and fuel cycle analysis for Thorium-Uranium Breeding Recycle in current PWRs, without any major change to the fuel lattice and the core internals, but substituting the UOX pellet with Thorium-based pellet. The fuel cycle analysis indicates that Thorium-Uranium Breeding Recycle is technically feasible in current PWRs. A 4-loop, 193-assembly PWR core utilizing 17 x 17 fuel assemblies (FAs) was taken as the model core. Two mixed cores were investigated respectively loaded with mixed reactor grade Plutonium-Thorium (PuThOX) FAs and mixed reactor grade {sup 233}U-Thorium (U{sub 3}ThOX) FAs on the basis of reference full Uranium oxide (UOX) equilibrium-cycle core. The UOX/PuThOX mixed core consists of 121 UOX FAs and 72 PuThOX FAs. The reactor grade {sup 233}U extracted from burnt PuThOX fuel was used to fabrication of U{sub 3}ThOX for starting Thorium-. Uranium breeding recycle. In UOX/U{sub 3}ThOX mixed core, the well designed U{sub 3}ThOX FAs with 1.94 w/o fissile uranium (mainly {sup 233}U) were located on the periphery of core as a blanket region. U{sub 3}ThOX FAs remained in-core for 6 cycles with the discharged burnup achieving 28 GWD/tHM. Compared with initially loading, the fissile material inventory in U{sub 3}ThOX fuel has increased by 7% via 1-year cooling after discharge. 157 UOX fuel assemblies were located in the inner of UOX/U{sub 3}ThOX mixed core refueling with 64 FAs at each cycle. The designed UOX/PuThOX and UOX/U{sub 3}ThOX mixed core satisfied related nuclear design criteria. The full core performance analyses have shown that mixed core with PuThOX loading has similar impacts as MOX on several neutronic characteristic parameters, such as reduced differential boron worth, higher critical boron concentration, more negative moderator temperature coefficient, reduced control rod worth, reduced shutdown margin, etc.; while mixed core with U{sub 3}ThOX loading on the periphery of core has no visible impacts on neutronic characteristics compared with reference full UOX core. The fuel cycle analysis has shown that {sup 233}U mono-recycling with U{sub 3}ThOX fuel could save 13% of natural uranium resource compared with UOX once through fuel cycle, slightly more than that of Plutonium single-recycling with MOX fuel. If {sup 233}U multi-recycling with U{sub 3}ThOX fuel is implemented, more natural uranium resource would be saved. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sustained Recycle in Light Water and Sodium-Cooled Reactors

From a physics standpoint, it is feasible to sustain recycle of used fuel in either thermal or fast reactors. This paper examines multi-recycle potential performance by considering three recycling approaches and calculating several fuel cycle parameters, including heat, gamma, and neutron emission of fresh fuel; radiotoxicity of waste; and uranium utilization. The first recycle approach is homogeneous mixed oxide (MOX) fuel assemblies in a light water reactor (LWR). The transuranic portion of the MOX was varied among Pu, NpPu, NpPuAm, or all-TRU. (All-TRU means all isotopes through Cf-252.) The Pu case was allowed to go to 10% Pu in fresh fuel, but when the minor actinides were included, the transuranic enrichment was kept below 8% to satisfy the expected void reactivity constraint. The uranium portion of the MOX was enriched uranium. That enrichment was increased (to as much as 6.5%) to keep the fuel critical for a typical LWR irradiation. The second approach uses heterogeneous inert matrix fuel (IMF) assemblies in an LWR - a mix of IMF and traditional UOX pins. The uranium-free IMF fuel pins were Pu, NpPu, NpPuAm, or all-TRU. The UOX pins were limited to 4.95% U-235 enrichment. The number of IMF pins was set so that the amount of TRU in discharged fuel from recycle N (from both IMF and UOX pins) was made into the new IMF pins for recycle N+1. Up to 60 of the 264 pins in a fuel assembly were IMF. The assembly-average TRU content was 1-6%. The third approach uses fast reactor oxide fuel in a sodium-cooled fast reactor with transuranic conversion ratio of 0.50 and 1.00. The transuranic conversion ratio is the production of transuranics divided by destruction of transuranics. The FR at CR=0.50 is similar to the CR for the MOX case. The fast reactor cases had a transuranic content of 33-38%, higher than IMF or MOX.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Delamination recycling of multilayer plastic films: Solvent-assisted separation pathways and recovery of solid polyolefins

Multilayer plastic films are excellent packaging materials due to the bound layers of multiple polymers, with each different polymer contributing to the film properties. Desirable properties lead to continuously growing demand for multilayer films. Multilayer plastic films are typically single-use and, as such, their increased production and disposal have led to waste management problems. Multilayer films are not currently recyclable primarily due to the multiple bound polymers. This work advances delamination as a recycling process to separate and sequester valuable polymers from multilayer films, facilitating the incorporation of these polymers into the circular economy. We effect delamination in a physical process that preserves targeted polymers as solid film, hence retaining their embodied energy. This work documents three different pathways of inducing delamination of multilayer films, with appropriate solvents disrupting adhesion between adjacent layers or dissolving a minor component of the film in less than an hour and at temperatures below 90°C, and where all initial polyethylene is maintained in its solid form throughout the process and is recovered at high purity. Solvent-based delamination is exemplified on commercial multilayer films with majority polyethylene (PE), and polyethylene terephthalate (PET) or ethylene vinyl alcohol copolymer (EVOH) or nylon also present. Solvent-based delamination is an energy-efficient and environmentally friendly recycling process that improves upon dissolution-precipitation recycling, since delamination involves very little dissolution and no precipitation, and is superior to pyrolysis which breaks down the polymers, while delamination keeps polymer chains intact. Furthermore, delamination recycling can contribute to the sustainable use of multilayer films as they continue to protect our food and medicine.

Chemical Recycling↗

Closed‐Loop Recycling of Poly(pentylene Adipate‐ co ‐Terephthalate) via Amine‐Catalyzed Methanolysis

Advancing circularity through effective chemical recycling strategies is essential for enabling the sustainable use of emerging biodegradable polyesters in film applications. In this context, poly(pentylene adipate-co-terephthalate) with a 40/60 adipate-to-terephthalate ratio (PPeAT60), a significantly stiffer and partially biobased copolyester recently reported by our team, offers improved mechanical performance and processability compared to commercial poly(butylene adipate-co-terephthalate), while providing a platform to evaluate advanced recycling approaches for film applications. Here, this study describes depolymerization of PPeAT60 through amine-catalyzed methanolysis, followed by the repolymerization of the recovered monomers. The resulting repolymerized material exhibited a molar mass distribution, chemical structure, and thermal stability comparable to the virgin polymer, confirming the technical feasibility of the methanolysis-based recycling route. Both polymers displayed nearly identical melting, glass transition, and decomposition temperatures, crystallinity, and modulus, demonstrating full structural and mechanical reproducibility after recycling. Variations in crystallization kinetics, elongation at break, and barrier properties likely arise from trace impurities (<1%) introduced during processing acting as nucleating and stress-inducing agents. Overall, these results demonstrate that PPeAT60 retains its key properties after chemical recycling, establishing methanolysis as a promising platform for recycling of this partially biobased polymer that may be able to replace both conventional polyolefins and PBAT in flexible packaging applications.

09 BIOMASS FUELS↗

Solventless Dual‐Cure Liquid Resins Via Circular Use of Phthalic Anhydride for Recyclable Composite Applications

Abstract Fiber‐reinforced composites (FRCs) possess a remarkable strength‐to‐weight ratio, making them ideal light‐weighing alternative materials of metals used in automotive, aerospace, and outdoor equipment applications, but their recycling is challenging. Chemically recyclable thermoset polymers can enable fiber recovery and reuse; however, challenges remain in the separation and purification of depolymerized small molecules for efficient polymer recycling. To this end, a series of liquid resins for chemically recyclable polymer networks is designed based on phthalic anhydride, a widely produced and inexpensive chemical. The straightforward sublimation of phthalic anhydride is leveraged to enable a simple and efficient separation process for polymer recycling. To liquefy phthalic anhydride, five mono‐acryloyl‐phthalates are synthesized to obtain stable liquid resins together with phthalic diglycidyl ester. These liquid resins undergo dual‐cure reactions that comprise photopolymerization of acrylate and, subsequently, heat‐mediated epoxy‐acid polymerization reactions. These liquid resins exhibit moderate viscosities (2600–6400 cP @ 22 °C), fast curing, and robust thermomechanical properties (T g s from 71 to 116 °C). It is demonstrated that hydrolysis of the dual‐cured polymers completes within 2 h at 80 °C, and direct sublimation produces phthalic anhydride with 82% yield. This resin system is expected to provide a cost‐competitive, highly efficient platform for recyclable FRCs.

Polymer Science↗

Metal Powder Recyclability in Binder Jet Additive Manufacturing

The recyclability of 316L stainless steel powder in the binder jetting process has been determined. The powder characterization results demonstrated a 22% increase in the number of coarse particles (> 30 µm) and an 18.2% reduction in the number of small particles (< 10 µm) after recycling up to 16 times. A few elongated and irregular-shaped particles were found after recycling, possibly due to particle agglomeration during handling and sieving. Here, a negligible increase in the oxygen content by 0.036% was detected in the recycled powder. The density of sintered parts produced using recycled powder was approximately 1.5% lower than when using fresh powder due to the changes in the particle size distribution and the flowability of the powder caused by the changes in morphology. Final parts built using fresh and recycled powder showed similar hardness (155 ± 3 HV and 165 ± 9 HV) and yield strength (206 ± 16 MPa and 192 ± 10 MPa), respectively.

36 MATERIALS SCIENCE↗

Compressive strength and hydration processes of concrete with recycled aggregates

This paper deals with the correlation between the time evolution of the degree of hydration and the compressive strength of Recycled Aggregate Concrete (RAC) for different water to cement ratios and initial moisture conditions of the Recycled Concrete Aggregates (RCAs). Particularly, the influence of such moisture conditions is investigated by monitoring the hydration process and determining the compressive strength development of fully dry or fully saturated recycled aggregates in four RAC mixtures. Hydration processes are monitored via temperature measurements in hardening concrete samples and the time evolution of the degree of hydration is determined through a 1D hydration and heat flow model. The effect of the initial moisture condition of RCAs employed in the considered concrete mixtures clearly emerges from this study. In fact, a novel conceptual method is proposed to predict the compressive strength of RAC-systems, from the initial mixture parameters and the hardening conditions. -- Highlights: •The concrete industry is more and more concerned with sustainability issues. •The use of recycled aggregates is a promising solution to enhance sustainability. •Recycled aggregates affect both hydration processes and compressive strength. •A fundamental approach is proposed to unveil the influence of recycled aggregates. •Some experimental comparisons are presented to validate the proposed approach.

42 ENGINEERING↗

Impact of informal electronic waste recycling on metal concentrations in soils and dusts

Highlights: • Metal concentrations at e-waste sites exceeded concentrations at control sites. • Burning as an e-waste activity has the most negative environmental impact. • The type of activity at the sites is the main factor that influences metal concentrations. • E-waste recycling is a major source of metal pollution in Nigeria. • There is need to develop strategies to enforce existing e-waste regulations. Electronic and electrical equipment contains over 1000 different substances, including metals. During informal e-waste recycling some of these substances such as metals, are released into the environment causing environmental pollution. This study assessed the impact of different informal e-waste recycling activities (burning, dismantling, and repairing) on metal concentrations in top soils and various dust. A comparative cross-sectional study design was adopted to assess metal concentrations in top soils and in various dust samples from multiple e-waste recycling sites. Metal concentrations at e-waste recycling sites were compared to the concentrations at control sites in three study locations in Nigeria (Lagos, Ibadan, and Aba). In the three study locations, mean metal concentrations at the e-waste recycling sites exceeded the concentrations at the control sites and the Nigerian standard guideline values by 100 s to 1000 s times. Burning sites showed the highest pollution level, followed by dismantling sites, then repair sites. Our findings show serious environmental and public health concerns. The metal concentrations were also higher than levels reported in other studies at the same locations in Nigeria, indicating that the situation is worsening. This study provides scientific evidence for an urgent need to develop effective strategies to strengthen enforcement of existing e-waste regulations in Nigeria.

54 ENVIRONMENTAL SCIENCES↗

Sustainability-inspired cell design for a fully recyclable sodium ion battery

Large-scale applications of rechargeable batteries consume nonrenewable resources and produce massive amounts of end-of-life wastes, which raise sustainability concerns in terms of manufacturing, environmental, and ecological costs. Therefore, the recyclability and sustainability of a battery should be considered at the design stage by using naturally abundant resources and recyclable battery technology. Herein, we design a fully recyclable rechargeable sodium ion battery with bipolar electrode structure using Na 3 V 2 (PO 4 ) 3 as an electrode material and aluminum foil as the shared current collector. Such a design allows exceptional sodium ion battery performance in terms of high-power correspondence and long-term stability and enables the recycling of ~ 100% Na 3 V 2 (PO 4 ) 3 and ~ 99.1% elemental aluminum without the release of toxic wastes, resulting in a solid-component recycling efficiency of >98.0%. The successful incorporation of sustainability into battery design implies that closed-loop recycling and the reutilization of battery materials can be achieved in next-generation energy storage technologies.

25 ENERGY STORAGE↗

Recycling lead and transparent conductors from perovskite solar modules

Abstract Perovskite photovoltaics are gaining increasing common ground to partner with or compete with silicon photovoltaics to reduce cost of solar energy. However, a cost-effective waste management for toxic lead (Pb), which might determine the fate of this technology, has not been developed yet. Here, we report an end-of-life material management for perovskite solar modules to recycle toxic lead and valuable transparent conductors to protect the environment and create dramatic economic benefits from recycled materials. Lead is separated from decommissioned modules by weakly acidic cation exchange resin, which could be released as soluble Pb(NO 3 ) 2 followed by precipitation as PbI 2 for reuse, with a recycling efficiency of 99.2%. Thermal delamination disassembles the encapsulated modules with intact transparent conductors and cover glasses. The refabricated devices based on recycled lead iodide and recycled transparent conductors show comparable performance as devices based on fresh raw materials. Cost analysis shows this recycling technology is economically attractive.

14 SOLAR ENERGY↗

Closed Loop Recycling of Electric Vehicle Batteries to Enable Ultra-high Quality Cathode Powder

The lithium-ion battery (LIB) recycling market is becoming increasingly important because of the widespread use of LIBs in every aspect of our lives. Mobile devices and electric cars represent the largest application areas for LIBs. Vigorous innovation in these sectors is spurring continuous deployment of LIB powered devices, and consequently more and more LIBs will become waste as they approach end of life. Considering the significant economic and environmental impacts, recycling is not only necessary, but also urgent. The WPI group has successfully developed a closed-loop recycling process, and has previously demonstrated it on a relatively small scale 1 kg spent batteries per experiment. Here, we show that the closed-loop recycling process can be successfully scaled up to 30 kg of spent LIBs from electric vehicle recycling streams, and the recovered cathode powder shows similar (or better) performance to equivalent commercial powder when evaluated in both coin cells and single layer pouch cells. All of these results demonstrate the closed-loop recycling process has great adaptability and can be further developed into industrial scale.

36 MATERIALS SCIENCE↗

A green closed-loop process for selective recycling of lithium from spent lithium-ion batteries

As the economy started to recover from the COVID pandemic, the price of Li 2 CO 3 skyrocketed to its highest. This situation has aggravated concerns about the supply chain for lithium-ion batteries (LIBs). Recycling spent LIBs is a potential solution to alleviate the bottleneck of the supply chain and prevent environmental pollution, and has attracted lots of attention. However, lithium recycling is generally disregarded because of the complex recycling process and its low recycling efficiency. Here, in this work we developed a sustainable lithium recovery process, which can selectively leach and recover lithium with formic acid before recycling valuable metals. With the reported method, lithium can be 99.8% recovered from layered oxide cathode materials with 99.994% purity. In addition, this lithium recovery process is affordable, compared to the typical hydrometallurgical process, by saving 11.15% per kilogram of spent LIBs. Therefore, this research provided a new solution to eliminating the effects of lithium ions on valuable metal separation and the co-precipitation reaction and precluding the influence of other metal ions on lithium recovery. Finally, this simplified lithium recovery process provides new opportunities for sustainable recycling of LIBs and economical restoration of the lithium supply chain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Active Recycling Control Through Lithium Injection in EAST

The coating of tokamak walls with thin layers of lithium has been demonstrated to reduce plasma recycling from the plasma-facing surfaces and to improve overall plasma performance. These effects, including reduced divertor D α emission, the elimination of edge-localized modes, and increased energy confinement have been observed in multiple experiments when lithium coatings are applied before plasma discharges. However, this coating technology does not extrapolate to future long-pulse devices, since the lithium coatings will be passivated by the continual plasma flux onto the surface. In order to provide active conditioning capability, a new technology has been developed that is capable of injecting lithium powder into the scrape-off layer plasma during plasma discharges, where it quickly liquefies and turns into an aerosol. The use of this “lithium dropper” is under study at the Experimental Advanced Superconducting Tokamak (EAST), where the potential benefits of real-time wall conditioning via lithium injection are being tested. Here, we present an analysis of the recycling characteristics during EAST experiments testing active lithium injection in order to assess recycling reduction and control. Lithium aerosol was injected from the top of the machine, with one system dropping lithium near the X-point and another into the low-field side divertor leg. The injection of lithium into the SOL reduced divertor recycling, as evidenced by reduced D α emission with ion flux measured by probes relatively unchanged. This effect is strongest in the active divertor, confirming the lithium is transported to strongly plasma-wetted areas. Furthermore, quantitative analysis of the recycling changes using the SOLPS edge plasma and neutral transport code indicated a ~20% reduction in recycling coefficient with lithium injection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recovery of postconsumer mechanically recycled polymers

Mechanical recycling plays a key role in reducing landfill bound plastics that pollute our environment. This process converts plastic waste into marketable pellets by sorting, cleaning, grinding into flakes, compounding in the molten state, and ultimately pelletizing. A primary restriction for the widescale usage of mechanical recycling is the highly variable quality and mechanical properties of the plastic waste feedstock. Degradation can occur during the plastic life cycle with the consumer, during the mechanical processing itself, or during the complex sorting process required to produce the feedstock. This study explores how rheological characterization can mitigate the batch-to-batch variability and identify a potential application for each batch. Shear and extensional rheology of “application-specific” virgin high-density polyethylene (HDPE) and virgin polypropylene (PP) was used as the control for this categorization process. Recycled HDPE and PP from three different streams were then measured and compared to the results from the control study. Rheological measurements proved to be very effective at providing sufficient differentiation to categorize the recycled polymer as suitable for different applications such as injection molding, blow molding, or thermoforming. Finally, the usage of an additional step to sort the recycled polymers by their initial use application was found to achieve a remarkably consistent recovery of application-specific material properties. Furthermore, this secondary sorting could provide significant added value for mechanically recycled polymers.

Differential scanning calorimetry↗

Manufacture and testing of biomass-derivable thermosets for wind blade recycling

Wind energy is helping to decarbonize the electrical grid, but wind blades are not recyclable, and current end-of-life management strategies are not sustainable. Here, to address the material recyclability challenges in sustainable energy infrastructure, we introduce scalable biomass-derivable polyester covalent adaptable networks and corresponding fiber-reinforced composites for recyclable wind blade fabrication. Through experimental and computational studies, including vacuum-assisted resin-transfer molding of a 9-meter wind blade prototype, we demonstrate drop-in technological readiness of this material with existing manufacture techniques, superior properties relative to incumbent materials, and practical end-of-life chemical recyclability. Most notable is the counterintuitive creep suppression, outperforming industry state-of-the-art thermosets despite the dynamic cross-link topology. Overall, this report details the many facets of wind blade manufacture, encompassing chemistry, engineering, safety, mechanical analyses, weathering, and chemical recyclability, enabling a realistic path toward biomass-derivable, recyclable wind blades.

17 WIND ENERGY↗

End-of-Life Plastics Management: A Review: Mechanical recycling, pyrolysis and hydrocracking methods

End-of-life plastics present a significant challenge to achieving a sustainable economy. It is crucial to develop environmentally friendly technologies to process the waste streams beyond landfilling. This review provides a detailed overview of end-of-life plastics management, covering mechanical recycling, pyrolysis and hydrocracking methods. Mechanical recycling is the predominant technique employed on a large scale in recycling end-of-life plastics, and this review discusses the technoeconomic assessment and life cycle assessment (LCA) of mechanical recycling. This review also summarises key studies concentrating on chemical recycling techniques for handling end-of-life plastics. Among these, pyrolysis and hydrocracking are discussed in depth. Recent advancements and fundamentals of these two techniques are covered, highlighting their significance in tackling the plastic waste challenge. The prospects of scaling up pyrolysis and hydrocracking technologies are interpreted in terms of technical and economic feasibility. The discussion concludes with recommendations for future research to commercialise chemical recycling of end-of-life plastics.

Chemistry↗