Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Range”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

An in-vacuum x-ray diffraction microscope for use in the 0.7-2.9 keV range

A dedicated in-vacuum coherent x-ray diffraction microscope was installed at the 2-ID-B beamline of the Advanced Photon Source for use with 0.7-2.9 keV x-rays. The instrument can accommodate three common implementations of diffractive imaging; plane wave illumination; defocused-probe (Fresnel diffractive imaging) and scanning (ptychography) using either a pinhole, focused or defocused probe. The microscope design includes active feedback to limit motion of the optics with respect to the sample. Upper bounds on the relative optics-to-sample displacement have been measured to be 5.8 nm(v) and 4.4 nm(h) rms/h using capacitance micrometry and 27 nm/h using x-ray point projection imaging. The stability of the measurement platform and in-vacuum operation allows for long exposure times, high signal-to-noise and large dynamic range two-dimensional intensity measurements to be acquired. Finally, we illustrate the microscope's stability with a recent experimental result.

43 PARTICLE ACCELERATORS↗

Characterizations of MCP performance in the hard x-ray range (6–25 keV)

MCP detector performance at hard x-ray energies from 6 to 25 keV was recently investigated using NSLS beamline X15A at BNL. Measurements were made with an NSTec Gen-II (H-CA-65) framing camera, based on a Photonis MCP with ∼10 μm in diameter pores, ∼12 μm center-center spacing, an L/D ratio of 46, and a bias angle of 8°. The MCP characterizations were focused on (1) energy and angle dependent sensitivity, (2) energy and angle dependent spatial resolution, (3) energy dependent gain performance, and (4) energy dependent dynamic range. These measurement corroborated simulation results using a Monte Carlo model that included hard x-ray interactions and the subsequent electron cascade in the MCP.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Range Fuels Inc/ Range Fuels Soperton Plant LLC Final Technical Report

Range Fuels Soperton Plant LLC (Recipient) signed an amended TIA with the DOE to help facilitate the design, construction, and operation of a commercial scale biorefinery for production of biofuels and other products in a replicable, commercial, integrated biorefinery process that will meet or exceed DOE requirement as required in the FOA for processing at least 700 dry (metric) tonnes per day (772 dry short tons per day) of lignocellulosic feedstocks from forestry waste and timber. Construction of the Project was to be carried out in two distinct phases. During Phase 1, a module with a Design Capacity of 125 dry tons per day was to be constructed and operated to demonstrate commercial scale operational and technological viability and provide data for Project design optimization. Phase 2 would consist of five additional modules with a combined Design Capacity of at least 650 dry tons per day incorporating Phase 1 into an integrated facility with a total Design Capacity of 775 dry tons per day meeting or exceeding DOE's commercial throughput requirements for the Project. This funding is intended to partially reimburse the initial construction, commissioning and startup, and operating costs for this first-of-its-kind integrated biorefinery and enable the development of a biofuels industry. This purpose is consistent with Section 932 of the Energy Policy Act of 2005. The plant was built on schedule and under budget.

09 BIOMASS FUELS↗

Advanced electrolytes for fast-charging high-voltage lithium-ion batteries in wide-temperature range

LiNixMnyCo1-x-yO2 (NMC) cathode materials with Ni=0.8 have attracted great interest for application in high energy-density lithium (Li)-ion batteries (LIBs) because of their high specific capacities at high voltages. However, the practical application of Ni-rich NMC in LIBs under high charge voltages (e.g. 4.4 V and above) still faces big challenges due to the severe capacity fading, which is directly related to the instability of the cathode/electrolyte interface. In this work, we develop new localized high-concentration electrolytes (LHCEs) based on carbonate solvents, which are compatible with graphite (Gr) anode and have a high oxidation potential over 4.9 V vs. Li/Li+. The optimal LHCE enables the Gr||NMC811 cells with 2.8 mAh cm-2 cathode areal capacity loading to achieve an excellent cycling stability over 600 cycles with a capacity retention of 94.2 % under a charge cut-off voltage of 4.4 V at 25 ?C, good rate capabilities under fast charging or discharging up to 3C rate, and superior low-temperature discharge performance down to -30 ?C with a capacity retention of 85.6% at C/5 rate. The findings in this work shed light a very promising strategy to develop new electrolytes for practical high-energy LIBs with Ni-rich NMC cathodes.

Zhang, Xianhui↗

Pressure‐Tuneable Visible‐Range Band Gap in the Ionic Spinel Tin Nitride

Abstract The application of pressure allows systematic tuning of the charge density of a material cleanly, that is, without changes to the chemical composition via dopants, and exploratory high‐pressure experiments can inform the design of bulk syntheses of materials that benefit from their properties under compression. The electronic and structural response of semiconducting tin nitride Sn 3 N 4 under compression is now reported. A continuous opening of the optical band gap was observed from 1.3 eV to 3.0 eV over a range of 100 GPa, a 540 nm blue‐shift spanning the entire visible spectrum. The pressure‐mediated band gap opening is general to this material across numerous high‐density polymorphs, implicating the predominant ionic bonding in the material as the cause. The rate of decompression to ambient conditions permits access to recoverable metastable states with varying band gaps energies, opening the possibility of pressure‐tuneable electronic properties for future applications.

Kearney, John S. C.↗

Interplay between Short and Long-Ranged Forces Leading to the Formation of Ag Nanoparticle Superlattice

Nanoparticle (NP) superlattices have attracted increasing attention due to their unique properties. However, key questions remain for predicting the nanoparticle behavior from interparticle forces, especially the role of hydration force (Fhyd) and its correlation to other forces, regarding the transient and final superlattice configurations. Here we investigated the self-assembly of Ag NPs in aqueous solution by employing in situ liquid cell transmission electron microscopy, combined with atomic force microscopy based force measurements and theoretical calculations. In spite of instantaneous Brownian motion of NPs, a correlation between velocity and van der Waals force (FvdW) on average was observed during the later self-assembly process. In the post-assembly state, a delicate balance between Fhyd and FvdW gives rise to ~ 0.6~0.9 nm separation be-tween NPs in the superlattice. Our study demonstrates pivotal roles of interparticle forces, enabling the control of the separation which is critical for tailoring the properties of superlattices.

Lee, Jaewon↗

Potential Economic Values of Low-Vapor-Pressure Gasoline-Range Bio-Blendstocks: Property Estimation, and Blending Optimization

Adding non-traditional blendstocks derived from biomass into gasoline has gained renewed interest since it will reduce greenhouse gas emissions and potentially enhance fuel properties and boost engine efficiencies. A competitive bio-blendstock candidate should have either lower prices or superior properties or both relative to conventional gasoline blending components. Gasoline is a mixture of hundreds compounds specified by properties rather than compositions. The addition of bio-blendstocks, most likely oxygenates, will modify the property mixing rules due to the non-ideal interactions between polar and nonpolar components. This paper presents an equation-of-state-based model for predicting Reid vapor pressure, reduced order non-linear property blending models for computing key properties of final gasoline products, and a blending optimization approach to identify key economic drivers. This paper also evaluates the economic values of bio-blendstocks to petroleum refiners using those models. In additional to ethanol, six low-vapor-pressure bio-blendstock candidates were evaluated: i-propanol, n-propanol, i-butanol, diisobutylene, cyclopentanone, and a mixture of furans. Reid vapor pressure, distillation temperatures, and octane numbers were identified as the key economic drivers of adding bio-blendstock. The economic values of those bio-blendstocks range from 2.22 to 4.00 US dollar per gasoline gallon equivalent in 2013 to 2017 5-year averaged price basis. The bio-blendstocks with higher octane numbers may have higher economic values. The uncertainties in property predictions may lead to roughly 15% deviation in the economic value evaluation.

Jiang, Yuan↗

Continuous hydrodeoxygenation of lignin to jet-range aromatic hydrocarbons

Sustainable aviation fuel (SAF) is essential to decrease the carbon footprint of the aviation industry. Although many strategies have been developed to provide the branched, aliphatic components of SAF, few viable strategies have been demonstrated to supply the aromatic and cycloalkane fraction of SAF at the necessary scale from bio-based feedstocks. Lignin is the largest natural source of renewable aromatic compounds, yet major challenges in deoxygenation have prevented its use as a feedstock for SAF. Here we report a continuous, two-stage catalytic process using molybdenum carbide to deoxygenate lignin from poplar into aromatic hydrocarbons with 87.5% selectivity towards aromatic hydrocarbons at 86% of the theoretical carbon recovery. This work demonstrates an effective approach to convert lignin into aromatic SAF blendstocks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

One-dimensional nanoclustering of the Cu(100) surface under CO gas in the mbar pressure range

The bulk terminated Cu(100) surface becomes unstable in the presence of CO at room temperature when the pressure reaches the mbar range. Scanning tunneling microscopy images show that above 0.25 mbar the surface forms nanoclusters with CO attached to peripheral Cu atoms. At 20 mbar and above 3-atom wide one-dimensional nanoclusters parallel to < 001 > directions cover the surface, with CO on every Cu atom, increasing in density up to 115 mbar. Density functional theory explains the findings as a result of the detachment of Cu atoms from step edges caused by the stronger binding of CO relative to that on flat terraces.

Chemistry↗

Examination of How Well Long-Range-Corrected Density Functionals Satisfy the Ionization Energy Theorem

For this work, we calculated the vertical ionization energies (VIE) of 99 species in two ways to examine the accuracy of several long-range-corrected (LC) hybrid meta functionals in comparison with a gradient approximation (GA), global hybrids, and doubly hybrids. In the category of LC functionals, we examined both those with meta ingredients (i.e., that depend on the kinetic energy density) and those without them. The LC-hybrid meta functionals examined are M11, revM11, M11plus, and ωB97M-V. The reference data used to assess accuracy consist of 95 molecules and 4 atoms in the GW100 set. The two methods studied are the ΔSCF method (involving the difference of neutral and cation self-consistent field (SCF) energies) and the ionization energy theorem (involving the orbital energy of the highest occupied molecular orbital, HOMO). We calculated linear correlation coefficients (r 2 ) and mean absolute deviations (MADs) between each approach and the reference VIE value from the CCSD(T)/def2-TZVPP level of theory. We compared the new LC-hybrid meta calculations to calculations with the 10 functionals in a previous VIE study by Brémond et al. and to the calculations with LC-BLYP (LC-Becke, Lee–Yang–Parr), CAM-B3LYP (Coulomb-attenuating-method Becke-3-parameter Lee–Yang–Parr), LC-ωHPBE, and ωB97X-D. The results show that Minnesota LC-hybrid meta functionals have the smallest mean absolute deviation of ionization energy theorem VIEs with the reference data; the LC-ωHPBE functional also does quite well in this test. This is very encouraging and indicates that LC-hybrid meta functionals would be the best starting points for the tuning strategy that has been shown to be a very good procedure for improving time-dependent density functional calculations, and it also helps explain the good success of LC-hybrid meta functionals for molecular excitation energies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Measuring Long-Range 13 C– 13 C Correlations on a Surface under Natural Abundance Using Dynamic Nuclear Polarization-Enhanced Solid-State Nuclear Magnetic Resonance [Measuring Long Range 13 C– 13 C Correlations on Surface under Natural Abundance Using DNP-enhanced Solid-state NMR]

Here, we report that spatial (<1 nm) proximity between different molecules in solid bulk materials and, for the first time, different moieties on the surface of a catalyst, can be established without isotope enrichment by means of homonuclear CHHC solid-state nuclear magnetic resonance experiment. This 13 C– 13 C correlation measurement, which hitherto was not possible for natural-abundance solids, was enabled by the use of dynamic nuclear polarization. Importantly, it allows the study of long-range correlations in a variety of materials with high resolution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗