Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1936

Boosted performance of a compression-ignition engine with a displaced piston

Performance tests were made using a rectangular displacer arranged so that the combustion air was forced through equal passages at either end of the displacer into the vertical-disk combustion chamber of a single-cylinder, four-stroke-cycle compression-ignition test engine. After making tests to determine optimum displacer height, shape, and fuel-spray arrangement, engine-performance tests were made at 1,500 and 2,000 r.p.m. for a range of boost pressures from 0 to 20 inches of mercury and for maximum cylinder pressures up to 1,150 pounds per square inch. The engine operation for boosted conditions was very smooth, there being no combustion shock even at the highest maximum cylinder pressures. Indicated mean effective pressures of 240 pounds per square inch for fuel consumptions of 0.39 pound per horsepower-hour have been readily reproduced during routine testing at 2,000 r.p.m. at a boost pressure of 20 inches of mercury.

Moore, Charles S↗
NASA NTRS1946

Performance of 19XB-2A Gas Turbine: Effect of Pressure Ratio and Inlet Pressure on Turbine Performance for an Inlet Temperature of 800 degree R - 1

An investigation of the 19XB-2A gas turbine is being conducted at the Cleveland laboratory to determine the effect on turbine performance of various inlet pressures, inlet temperatures, pressure ratios, and wheel speeds. The engine of which this turbine is a component is designed to operate at an air flow of 30 pounds per second at a compressor rotor speed of 17,000 rpm at sea-level conditions. At these conditions the total-pressure ratio is 2.08 across the turbine and the turbine inlet total temperature is 2000 degrees R. Runs have been made with turbine inlet total pressures of 20, 30, 40, and 45 inches of mercury absolute for a constant total pressure ratio across the turbine of 2.40, the maximum value that could be obtained. Additional runs have been made with total pressure ratios of 1.50 and 2.00 at an inlet total pressure of 45 inches of mercury absolute. All runs were made with an inlet total temperature of 800 degrees R over a range of corrected turbine wheel speeds from 40 to 150 percent of the corrected speed at the design point. The turbine efficiencies at these conditions are presented.

Kohl, Robert C.↗
NASA NTRS1994

Method development for compensating temperature effects in pressure sensitive paint measurements

Pressure sensitive luminescent paints (PSP) have recently emerged as a viable technique for aerodynamic pressure measurements. The technique uses a surface coating which contains probe molecules that luminesce when excited by light of an appropriate wavelength. The photoluminescence of these materials is known to be quenched by the presence of molecular oxygen. Since oxygen is a fixed mole fraction of the air, the coating's luminescence intensity varies inversely with air pressure. Digital imaging of the luminescence varying across a coated surface produces a pressure distribution map over that surface. One difficulty encountered with this technique is the temperature effect on the luminescence intensity. Present PSP formulations have significant sensitivity to temperature. At the moment, the most practical way of correcting for temperature effects is to calibrate the paint in place at the operating temperatures by using a few well-placed pressure taps. This study is looking at development of temperature indicating coatings that can be applied and measured concurrently with PSP, and use the temperature measurement to compute the correct pressure. Two methods for this dual paint formulation are proposed. One method will use a coating that consists of temperature sensitive phosphors in a polymer matrix. This is similar in construction to PSP, except that the probe molecules used are selected primarily for their temperature sensitivity. Both organic phosphors (e.g., europium thenoyltrifluoroacetonate, bioprobes) and inorganic phosphors (e.g., Mg4(F)GeO6:Mn, La2O2S:Eu, Radelin Type phosphors, Sylvania Type phosphors) will be evaluated for their temperature sensing potential. The next method will involve a novel coating composing of five membered heterocyclic conducting polymers which are known to show temperature dependent luminescence (e.g., poly(3-alkylthiopene), poly(3-alkylselenophene), poly(3-alkylfuran)). Both methods will involve applying a bottom layer of temperature sensitive coating followed by a top coating of PSP. An oxygen-impermeable polymer can be used as the temperature sensitive coating matrix, or it can be layered in between the coatings to prevent oxygen quenching of the bottom coating's luminescence. The probe molecules of the coatings will be excited by a broad band of light, with the different emissions detected and measured at their distinct wavelengths. Developmental research of these coatings is still in progress; however, preliminary results look very promising.

Demandante, Carlo Greg N.↗
NASA NTRS1987

Pressure scaling effects in a scramjet combustion chamber

The test results obtained for a model scramjet over a range of pressure levels corresponding to different flight altitudes involve enthalpies that vary from the ignition limit, at the low temperature end, to temperatures where the dissociation of combustion products severely limits heat release. The minimum temperature is noted to be highly pressure-sensitive; above the ignition limit, the amount of heat release increased markedly with pressure and with combustion chamber length. A FEM computer code has been used to model the mixing and combustion processes.

Morgan, R. G.↗
NASA NTRS1988

Thermal and pressure diffusion effects in high altitude flows

An apparently anomalous change in composition adjacent to a non-catalytic surface in an earlier DSMC calculation of a non-reacting gas mixture is shown to have been due to thermal diffusion. Both thermal and pressure diffusion can lead to species separation effects in the flow of gas mixtures, but are not generally included in Navier-Stokes formulations. Additional DSMC calculations are made for blunt-body and plume expansion flows using both a simple gas and an otherwise identical gas mixture. These test calculations indicate that the pressure distribution on the forward face of a blunt body is largely unaffected by the species separation in the stagnation region. The gas density in this region is significantly affected and there is a slight change in the heat transfer to the surface. The pressure distribution around the shoulder of the body is affected. Very large separations occur in the plume expansion of the gas mixtures and there is an order of magnitude increase in density in the backflow region for the mixture.

Bird, G. A.↗
NASA NTRS1987

Experimental evaluation of blockage ratio and plenum evacuation system flow effects on pressure distribution for bodies of revolution in 0.1 scale model test section of NASA Lewis Research Center's proposed altitude wind tunnel

An experimental investigation was conducted in the slotted test section of the 0.1-scale model of the proposed Altitude Wind Tunnel to evaluate wall interference effects at tunnel Mach numbers from 0.70 to 0.95 on bodies of revolution with blockage rates of 0.43, 3, 6, and 12 percent. The amount of flow that had to be removed from the plenum chamber (which surrounded the slotted test section) by the plenum evacuation system (PES) to eliminate wall interference effects was determined. The effectiveness of tunnel reentry flaps in removing flow from the plenum chamber was examined. The 0.43-percent blockage model was the only one free of wall interference effects with no PES flow. Surface pressures on the forward part of the other models were greater than interference-free results and were not influenced by PES flow. Interference-free results were achieved on the aft part of the 3- and 6-percent blockage models with the proper amount of PES flow. The required PES flow was substantially reduced by opening the reentry flaps.

Burley, Richard R.↗
NASA NTRS1955

Preliminary Results of the Determination of Inlet-Pressure Distortion Effects on Compressor Stall and Altitude Operating Limits of the J57-P-1 Turbojet Engine

During an investigation of the J57-P-1 turbojet engine in the Lewis altitude wind tunnel, effects of inlet-flow distortion on engine stall characteristics and operating limits were determined. In addition to a uniform inlet-flow profile, the inlet-pressure distortions imposed included two radial, two circumferential, and one combined radial-circumferential profile. Data were obtained over a range of compressor speeds at an altitude of 50,000 and a flight Mach number of 0.8; in addition, the high- and low-speed engine operating limits were investigated up to the maximum operable altitude. The effect of changing the compressor bleed position on the stall and operating limits was determined for one of the inlet distortions. The circumferential distortions lowered the compressor stall pressure ratios; this resulted in less fuel-flow margin between steady-state operation and compressor stall. Consequently, the altitude operating Limits with circumferential distortions were reduced compared with the uniform inlet profile. Radial inlet-pressure distortions increased the pressure ratio required for compressor stall over that obtained with uniform inlet flow; this resulted in higher altitude operating limits. Likewise, the stall-limit fuel flows required with the radial inlet-pressure distortions were considerably higher than those obtained with the uniform inlet-pressure profile. A combined radial-circumferential inlet distortion had effects on the engine similar to the circumferential distortion. Bleeding air between the two compressors eliminated the low-speed stall limit and thus permitted higher altitude operation than was possible without compressor bleed.

Wallner, L. E.↗
NASA NTRS1945

The Effect of Compression Ratio on Knock Limits of High-Performance Fuels in a CFR Engine II : Blends of 2,2,3-Trimethylpentane with 28-R

The knock-limited performance of blends of 0,50; and 100 percent by volume of 2,2,3-trimethylpentane in 28-R fuel determined with a modified F-4 engine at three sets of conditions varying from severe to mild at each of three compression ratios (6.0, 8.0, and 10.0). A comparison of the knock-limited performance of 2,2,3-trimethylpentane with that of triptane (2,2,3-trimethylbutane) is included. The knock-Limited performance of 2,2,3-trimethylpontane was usually more sensitive to either compression ratio or inlet-air temperature than 28-R fuel, but the ratio of the knock-limited indicated mean effective pressure of a given blend containing 2,2,3-trimethypentane and 28-R to the indicated mean effective pressure of 28-R alone was not greatly affected by compression ratio if the engine operating conditions were mild. Although 2,2,3-trimethylpentane in general had a lower knock-limited performance than triptane, the characteristics of the two fuels were somewhat similar.

FUELS, ANTIKNOCK↗
NASA NTRS1944

Compressibility and Heating Effects on Pressure Loss and Cooling of a Baffled Cylinder Barrel

Theoretical investigations have shown that, because air is compressible, the pressure-drop requirements for cooling an air-cooled engine will be much greater at high altitudes and high speeds than at sea level and low speeds. Tests were conducted by the NACA to obtain some experimental confirmation of the effect of air compressibility on cooling and pressure loss of a baffled cylinder barrel and to evaluate various methods of analysis. The results reported in the present paper are regarded as preliminary to tests on single-cylinder and multicylinder engines. Tests were conducted over a wide range of air flows and density altitudes.

Goldstein, Arthur W↗
NASA NTRS1944

Compressibility and Heating Effects on Pressure Loss and Cooling of a Baffled Cylinder Barrel

Theoretical investigations have shown that, because air is compressible, the pressure-drop requirements for cooling an air-cooled engine will be much greater at high altitudes and high speeds than at sea level and low speeds. Tests were conducted by the NACA to obtain some experimental confirmation of the effect of air compressibility on cooling and pressure loss of a baffled cylinder barrel and to evaluate various methods of analysis. The results reported in the present paper are regarded as preliminary to tests on single-cylinder and multi-cylinder engines. Tests were conducted over a wide range of air flows and density altitudes.

Goldstein, Arthur W.↗
NASA NTRS1991

Thermomolecular effect on pressure measurements with orifices in transitional flow

Results are presented of a study carried out in order to verify a version of the method (presented at the 7th International Rarefied Gas Dynamics Symposium) for calculating the influence of thermomolecular flow on the pressures measured by means of orifices in walls exposed to rarefied gases. In these experiments, the 'orifice effect' is examined under conditions that are significantly different from those for which the semiempirical (SE) method of Kinslow and Potter (1971) was shown to be successful. Comparisons between the predicted results with flight data and the results obtained in the laboratory, combined with limited DSMC calculations, indicate that the SE method remains a useful tool which is relatively easy to apply and which gives good results when an appropriate energy accommodation coefficient is used.

Potter, J. L.↗
NASA NTRS1980

Predicted and measured effects of pressure and crossflow velocity on composite propellant burning rate

A theoretical model for prediction of burning rates of composite (ammonium perchlorate oxidizer) solid propellants as a function of pressure and crossflow velocity was developed. Included in this model is the capability for treatment of multimodal oxidizer particle sizes and metalized formulations. In addition, an experimental device for measuring the effects of crossflow velocity on propellant burning rate was developed and used to characterize a series of AP/HTPB propellants with systematically varied formulation parameters. Model predictions of zero-crossflow burning rate versus pressure characteristics were found to be in agreement with data, while the agreement between erosive burning predictions and data is, in general, good. The experimental data indicate that the dominant factor influencing the sensitivity of composite propellant burning rate to crossflow is the base (no-crossflow) burning rate versus pressure characteristics of the propellant (lower base burning rate leading to increased crossflow sensitivity). Finally, the model was used to examine the effects of motor scaling on erosive burning: erosive burning is predicted to diminish with increasing motor size, in agreement with experience.

King, M. K.↗
NASA NTRS1980

Effect of pressure gradients on Gortler instability

Gortler instability for boundary-layer flows over generally curved walls is considered. The full linearized disturbance equations are obtained in an orthogonal curvilinear coordinate system. A perturbation procedure to account for second-order effects is used to determine the effects of the displacement thickness and the variation of the streamline curvature on the neutral stability of the Blasius flow. The pressure gradient in the mean flow is accounted for by solving the nonsimilar boundary-layer equations. Growth rates are obtained for the actual mean flow and the Falkner-Skan flows. The results demonstrate the strong influence of the pressure gradient and the nonsimilarity of the basic flow on the stability characteristics.

Ragab, S. A.↗
NASA NTRS1987

The effect of pressure and excitation energy on the isotopic fractionation in the formation of ozone by discharge of O2

Isotopic fractionation processes in the formation of O3 by discharge (at 20 kV and 3 MHz) of O2 in a fused silica container at 77 K are investigated experimentally, with a focus on the effects of changes in the isotopic abundances in the predischarge O2, the O2 pressure, and the excitation energy on the isotope abundances in the postdischarge O2 and O3. The results are presented in extensive tables and graphs and characterized in detail, and good general agreement is found with data obtained using 60-kHz excitation (Yang and Epstein, 1987). It is shown that O-17 and O-18 enrichment of the residual O2 (when the predischarge gas is enriched) or of the O3 (when atmospheric isotope abundances are used) can occur independently of one another. It is inferred that the rate of anharmonic predissociation of vibrationally hot O3 depends on the symmetry and mass of the O3 molecules. The significance of the present findings for studies of anomalous oxygen isotope abundances in meteorites is indicated.

Yang, Jongmann↗
NASA NTRS1973

Effect of sweep angle on the pressure distributions and effectiveness of the ogee tip in diffusing a line vortex

Low-speed wind tunnel tests were conducted to study the influence of sweep angle on the pressure distributions of an ogee-tip configuration with relation to the effectiveness of the ogee tip in diffusing a line vortex. In addition to the pressure data, performance and flow-visualization data were obtained in the wind tunnel tests to evaluate the application of the ogee tip to aircraft configurations. The effect of sweep angle on the performance characteristics of a conventional-tip model, having equivalent planform area, was also investigated for comparison with the ogee-tip configuration. Results of the investigation generally indicate that sweep angle has little effect on the characteristics of the ogee in diffusing a line vortex.

Balcerak, J. C.↗
NASA NTRS1991

Effect of pressure on electrostatic processes on Mars

Paschen's Law as illustrated by Paschen curves for various gases shows that the minimum breakdown voltage for gases for breakdown distances of interest, i.e., 1 to 1000 mm is at or near the surface pressure on Mars. This means that the physics of many electrostatic processes is markedly different on Mars than on Earth. The primary effect is that voltage potentials above 100 volts are subject to breakdown in the Martian atmosphere. Sharp electrodes, dusty atmospheric conditions, or other anomalies modify the breakdown voltage, usually causing lower breakdown voltages. Paschen's curves for most common pure gases were experimentally determined. A very small amount of mixing of different gases radically changes the curve as shown in the curve for neon plus 0.1 percent argon compared to either neon or argon. Paschen's curve for the exact composition of gases for Mars was not determined; thus, the breakdown voltages are not known. A second important effect is that the breakdown for most Martian cases is a glow discharge rather than a spark discharge. It would seem that simple measurements of breakdown manner and voltage should be included on a Mars lander vehicle.

Leach, Rodman N.↗