Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

High-pressure behavior of A 2 B 2 O 7 pyrochlore (A=Eu, Dy; B=Ti, Zr)

In situ high-pressure X-ray diffraction and Raman spectroscopy were used to determine the influence of composition on the high-pressure behavior of A 2 B 2 O 7 pyrochlore (A=Eu, Dy; B=Ti, Zr) up to ~50GPa. Based on X-ray diffraction results, all compositions transformed to the high-pressure cotunnite structure. The B-site cation species had a larger effect on the transition pressure than the A-site cation species, with the onset of the phase transformation occurring at ~41 GPa for B=Ti and ~16 GPa B=Zr. However, the A-site cation affected the kinetics of the phase transformation, with the transformation for compositions with the smaller ionic radii, i.e., A=Dy, proceeding faster than those with a larger ionic radii, i.e., A=Eu. These results were consistent with previous work in which the radius-ratio of the A- and B-site cations determined the energetics of disordering, and compositions with more similarly sized A- and B-site cations had a lower defect formation energy. Raman spectra revealed differences in the degree of short-range order of the different compositions. Due to the large phase fraction of cotunnite at high pressure for B=Zr compositions, Raman modes for cotunnite could be observed, with more modes recorded for A=Eu than A=Dy. These additional modes are attributed to increased short-to-medium range ordering in the initially pyrochlore structured Eu 2 Zr 2 O 7 as compared with the initially defect-fluorite structured Dy 2 Zr 2 O 7 .

36 MATERIALS SCIENCE↗

Wisconsin In Situ Penning (WISP) gauge: A versatile neutral pressure gauge to measure partial pressures in strong magnetic fields

A new type of in-vessel Penning gauge, the Wisconsin In Situ Penning (WISP) gauge, has been developed and successfully operated in the Wendelstein 7-X (W7-X) island divertor baffle and vacuum vessel. The capacity of the quantitative measurements of the neutral reservoir for light impurities, in particular, helium, is important for tokamaks as well as stellarator divertors in order to avoid fuel dilution and radiative energy loss. Penning gauges assisted by spectroscopy are a powerful tool to obtain the total neutral pressure as well as fractional neutral pressures of specific impurities. The WISP gauge is a miniaturized Penning gauge arrangement, which exploits the ambient magnetic field of magnetic confinement fusion experiments to establish the Penning discharge. Then, in situ spectroscopy is conducted to separate the fractional neutral pressures of hydrogen, helium, and possibly also other impurities. The WISP probe head was qualified using the magnetic field of the Magnetized Dusty Plasma Experiment at Auburn University between 0.25 T and 3.5 T [E. Thomas et al ., J. Plasma Phys. 81, 345810206 (2015)]. The in-depth quantitative evaluation for hydrogen and helium will be shown as well as an exploration of nitrogen, argon, and neon. A power law scaling between current I and pressure p, I = f (Gas,V) p n⁽Gas, B⁾ , was shown. The factor f is gas and anode potential dependent, while n is gas and magnetic field strength dependent. Pressure measurements from 0.1 mbar and down to 1 × 10 -5 mbar were achieved, demonstrating a reliable operating range for relevant pressure levels in the divertor and main vessel regions in current and future fusion devices, with a time resolution of up to 1 kHz. The lowest achievable pressure measurement increases with an increase in B and can be shifted with the anode potential V . At W7-X, the WISP probe head was mounted on an immersion tube setup that passes through the cryostat and places the probe head close to the plasma. Two probe heads were positioned in different divertor pump gaps, top and bottom, and one close to the plasma on the midplane in one module. The gauges were in situ calibrated together with the ASDEX pressure gauges [G. Haas and H.-S. Bosch, Vacuum 51, 39 (1998)]. Data were taken during the entire operation phase 1.2b, and measurements were coherent with other neutral gas pressure gauges. For the spectroscopic partial pressure measurements, channels of a spectroscopic detection system based on photo-multipliers, a so-called filterscope [R. J. Colchin et al ., Rev. Sci. Instrum. 74, 2068 (2003)], provided by the Oak Ridge National Lab were used.

47 OTHER INSTRUMENTATION↗

Structural transitions of 4:1 methanol–ethanol mixture and silicone oil under high pressure

A 4:1 (volume ratio) methanol–ethanol (ME) mixture and silicone oil are two of the most widely used liquid pressure-transmitting media (PTM) in high-pressure studies. Their hydrostatic limits have been extensively studied using various methods; however, the evolution of the atomic structures associated with their emerging nonhydrostaticity remains unclear. Here, we monitor their structures as functions of pressure up to ∼30 GPa at room temperature using in situ high-pressure synchrotron x-ray diffraction (XRD), optical micro-Raman spectroscopy, and ruby fluorescence spectroscopy in a diamond anvil cell. No crystallization is observed for either PTM. The pressure dependence of the principal diffraction peak position and width indicates the existence of a glass transition in the 4:1 ME mixture at ∼12 GPa and in the silicone oil at ∼3 GPa, beyond which a pressure gradient emerges and grows quickly with pressure. There may be another liquid-to-liquid transition in the 4:1 ME mixture at ∼5 GPa and two more glass-to-glass transitions in the silicone oil at ∼10 GPa and ∼16 GPa. By contrast, Raman signals only show peak weakening and broadening for typical structural disordering, and Raman spectroscopy seems to be less sensitive than XRD in catching these structural transitions related to hydrostaticity variations in both PTM. These results uncover rich pressure-induced transitions in the two PTM and clarify their effects on hydrostaticity with direct structural evidence. The high-pressure XRD and Raman data on the two PTM obtained in this work could also be helpful in distinguishing between signals from samples and those from PTM in future high-pressure experiments.

Chen, Xiehang (ORCID:0000000168541506)↗

THE RELATION BETWEEN MID-PLANE PRESSURE AND MOLECULAR HYDROGEN IN GALAXIES: ENVIRONMENTAL DEPENDENCE

Molecular hydrogen (H{sub 2}) is the primary component of the reservoirs of cold, dense gas that fuel star formation in our Galaxy. While the H{sub 2} abundance is ultimately regulated by physical processes operating on small scales in the interstellar medium (ISM), observations have revealed a tight correlation between the ratio of molecular to atomic hydrogen in nearby spiral galaxies and the pressure in the mid-plane of their disks. This empirical relation has been used to predict H{sub 2} abundances in galaxies with potentially very different ISM conditions, such as metal-deficient galaxies at high redshifts. Here, we test the validity of this approach by studying the dependence of the pressure-H{sub 2} relation on environmental parameters of the ISM. To this end, we follow the formation and destruction of H{sub 2} explicitly in a suite of hydrodynamical simulations of galaxies with different ISM parameters. We find that a pressure-H{sub 2} relation arises naturally in our simulations for a variety of dust-to-gas ratios or strengths of the interstellar radiation field in the ISM. Fixing the dust-to-gas ratio and the UV radiation field to values measured in the solar neighborhood results in fair agreement with the relation observed in nearby galaxies with roughly solar metallicity. However, the parameters (slope and normalization) of the pressure-H{sub 2} relation vary in a systematical way with ISM properties. A particularly strong trend is the decrease of the normalization of the relation with a lowering of the dust-to-gas ratio of the ISM. We show how this trend and other properties of the pressure-H{sub 2} relation arise from the atomic-to-molecular phase transition in the ISM caused by a combination of H{sub 2} formation, destruction, and shielding mechanisms.

79 ASTRONOMY AND ASTROPHYSICS↗

Prediction of crystal structures and motifs in the Fe–Mg–O system at Earth’s core pressures

Abstract Fe, Mg, and O are among the most abundant elements in terrestrial planets. While the behavior of the Fe–O, Mg–O, and Fe–Mg binary systems under pressure have been investigated, there are still very few studies of the Fe–Mg–O ternary system at relevant Earth’s core and super-Earth’s mantle pressures. Here, we use the adaptive genetic algorithm (AGA) to study ternary Fe x Mg y O z phases in a wide range of stoichiometries at 200 GPa and 350 GPa. We discovered three dynamically stable phases with stoichiometries FeMg 2 O 4 , Fe 2 MgO 4, and FeMg 3 O 4 with lower enthalpy than any known combination of Fe–Mg–O high-pressure compounds at 350 GPa. With the discovery of these phases, we construct the Fe–Mg–O ternary convex hull. We further clarify the composition- and pressure-dependence of structural motifs with the analysis of the AGA-found stable and metastable structures. Analysis of binary and ternary stable phases suggest that O, Mg, or both could stabilize a BCC iron alloy at inner core pressures.

Wang, Renhai↗

Magnetic ordering at anomalously high temperatures in Dy at extreme pressures

In an attempt to destabilize the magnetic state of the heavy lanthanide Dy, extreme pressures were applied in an electrical resistivity measurement to 157 GPa over the temperature range 1.3 - 295 K. The magnetic ordering temperature T o and spin-disorder resistance R sd of Dy, as well as the superconducting pair-breaking effect ΔT c in Y(1 at.% Dy), are found to track each other in a highly non-monotonic fashion as a function of pressure. Above 73 GPa, the critical pressure for a 6% volume collapse in Dy, all three quantities increase sharply (dT o =dP≃5.3 K/GPa), T o appearing to rise above ambient temperature for P > 107 GPa. In contrast, T o and ΔT c for Gd and Y(0.5 at.% Gd), respectively, show no such sharp increase with pressure (dT o =dP≃ 0.73 K/GPa). Altogether, these results suggest that extreme pressure transports Dy into an unconventional magnetic state with an anomalously high magnetic ordering temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Hall effect in LaCrGe 3 at pressures up to 24 kbar and a 𝐻−𝑇 phase diagram of the pressure-induced magnetic phase

LaCrGe 3 is a metallic, itinerant ferromagnet with 𝑇 𝐶 ≈ 86K and an easy magnetic direction along its hexagonal 𝑐 axis. Here we present studies of the 𝐻 ∥ 𝑐 Hall effect in LaCrGe 3 at ambient pressure and under pressures up to 24 kbar. At ambient pressure the anomalous Hall conductivity in the ferromagnetic state reaches a large value of ∼520 Ω − 1 cm −1 . The overall data are consistent with the behavior expected for a ferromagnet with magnetic field applied along its easy axis. Measurements under pressure yield an 𝐻 = 0, 𝑃−𝑇 phase diagram consistent with earlier publications with 𝑇 𝐶 being suppressed with pressure and nonferromagnetic phases appearing for 𝑃 >15 kbar. The data suggest that the observed 𝑇 𝐶 suppression is due to the pressure-dependent exchange interactions rather than suppression of the size of the magnetic moment. Field-dependent Hall resistivity in the higher-pressure, nonferromagnetic state is consistent with the net moment being zero for 𝐻=0. In a finite field there is a sharp anomaly comparable to the one associated with a spin-flip metamagnetic transition. The 𝐻−𝑇 phase diagrams corresponding to a pressure-induced magnetic phase are constructed for several pressures. In conclusion, the Hall data suggest the possibility of the pressure-induced nonferromagnetic phase being a combination of multiple small regions of antiferromagnetic phases with different wave vectors.

Bud'ko, Sergey L. [Ames Laboratory, and Iowa State↗

Flight Investigation of the Effects of Pressure-Belt Tubing Size on Measured Pressure Distributions

The pressure-belt technique is commonly used to measure pressure distributions on lifting and nonlifting surfaces where flush, through-the-surface measurements are not possible. The belts, made from strips of small-bore, flexible plastic tubing, are surface-mounted by a simple, nondestructive method. Additionally, the belts require minimal installation time, thus making them much less costly to install than flush-mounted pressure ports. Although pressure belts have been used in flight research since the early 1950s, only recently have manufacturers begun to produce thinner, more flexible tubing, and thin, strong adhesive tapes that minimize the installation-induced errors on the measurement of surface pressures. The objective of this investigation was to determine the effects of pressure-belt tubing size on the measurement of pressure distributions. For that purpose, two pressure belts were mounted on the right wing of a single-engine, propeller-driven research airplane. The outboard pressure belt served as a baseline for the measurement and the comparison of effects. Each tube had an outer diameter (OD) of 0.0625 in. The inboard belt was used to evaluate three different tube sizes: 0.0625-, 0.1250-, and 0.1875-in. OD. A computational investigation of tube size on pressure distribution also was conducted using the two-dimensional Multielement Streamtube Euler Solver (MSES) code.

Rivers, Natale A.↗

Experimental Investigation of Oscillatory Flow Pressure and Pressure Drop Through Complex Geometries

A series of experiments have been performed to investigate the oscillatory flow pressure and pressure drop through complex geometries. These experiments were conducted at the CSU-SLRE facility which is a horizontally opposed, two-piston, single-acting engine with a split crankshaft driving mechanism. Flow through a rectangular duct, with no insert (obstruction), was studied first. Then four different inserts were examined: Abrupt, Manifold, Diverging Short and Diverging Long. The inserts were mounted in the center of the rectangular duct to represent different type of geometries that could be encountered in Stirling machines. The pressure and pressure drop of the oscillating flow was studied for: 1) different inserts, 2) different phase angle between the two pistons of the engine (zero, 90 lead, 180, and 90 lag), and 3) for different piston frequencies (5, 10, 15, and 20 Hz). It was found that the pressure drop of the oscillatory flow increases with increasing Reynolds number. The pressure drop was shown to be mainly due to the gas inertia for the case of oscillatory flow through a rectangular duct with no insert. On the other hand, for the cases with different inserts into the rectangular duct, the pressure drop has three sources: inertia, friction, and local losses. The friction pressure drop is only a small fraction of the total pressure drop. It was also shown that the dimensionless pressure drop decreases with increasing kinetic Reynolds number.

Ibrahim, Mounir B.↗

Pressure-induced high-temperature superconductivity retained without pressure in FeSe single crystals

To raise the superconducting-transition temperature (T c ) has been the driving force for the long-sustained effort in superconductivity research. Recent progress in hydrides with T c s up to 287 K under pressure of 267 GPa has heralded a new era of room temperature superconductivity (RTS) with immense technological promise. Indeed, RTS will lift the temperature barrier for the ubiquitous application of superconductivity. Unfortunately, formidable pressure is required to attain such high T c s. The most effective relief to this impasse is to remove the pressure needed while retaining the pressure-induced T c without pressure. Here, we show such a possibility in the pure and doped high-temperature superconductor (HTS) FeSe by retaining, at ambient pressure via pressure quenching (PQ), its T c up to 37 K (quadrupling that of a pristine FeSe at ambient) and other pressure-induced phases. We have also observed that some phases remain stable without pressure at up to 300 K and for at least 7 d. The observations are in qualitative agreement with our ab initio simulations using the solid-state nudged elastic band (SSNEB) method. We strongly believe that the PQ technique developed here can be adapted to the RTS hydrides and other materials of value with minimal effort.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Modeling Self-Pressurization and Spray Bar Pressure Control of A Cryogenic Storage Tank in Normal Gravity

This paper presents computational fluid dynamics (CFD) models for simulating self-pressurization and spray-bar pressure control processes in a large-scale liquid hydrogen storage tank under normal gravity conditions. For self-pressurization, the model employs the kinetics-based Schrage equation alongside the volume-of-fluid (VOF) method to account for interfacial mass transfer. The CFD predictions of pressure and temperature are compared with experimental data from the Multipurpose Hydrogen Test Bed (MHTB) experiment, and the predicted interfacial mass transfer rates are also presented. A CFD model simulating pressure control using a spray bar has also been developed. An Eulerian-Lagrangian approach models the interactions between discrete droplets and the continuous ullage (vapor) phase. The spray model is coupled with the VOF method by tracking droplets in the ullage and removing them when they reach the liquid interface. The T-sat model calculates droplet-ullage heat and mass transfer, where droplets warm up to the saturation temperature corresponding to the ullage vapor pressure before evaporating while remaining at the saturation temperature. The evolution of tank pressure, vapor temperature, and liquid temperature predicted by the CFD model is validated against data from the MHTB spray-bar mixing experiment. Overall, the CFD models agree with experimental data, demonstrating their capability to simulate self-pressurization and pressure control processes in large-scale cryogenic storage tanks. These models can be valuable tools for designing and optimizing cryogenic fluid management systems in future applications.

Computational Fluid Dynamics↗

Modeling Self-Pressurization and Spray Bar Pressure Control of A Cryogenic Storage Tank in Normal Gravity

This paper presents computational fluid dynamics (CFD) models for simulating self-pressurization and spray-bar pressure control processes in a large-scale liquid hydrogen storage tank under normal gravity conditions. For self-pressurization, the model employs the kinetics-based Schrage equation alongside the volume-of-fluid (VOF) method to account for interfacial mass transfer. The CFD predictions of pressure and temperature are compared with experimental data from the Multipurpose Hydrogen Test Bed (MHTB) experiment, and the predicted interfacial mass transfer rates are also presented. A CFD model simulating pressure control using a spray bar has also been developed. An Eulerian-Lagrangian approach models the interactions between discrete droplets and the continuous ullage (vapor) phase. The spray model is coupled with the VOF method by tracking droplets in the ullage and removing them when they reach the liquid interface. The T-sat model calculates droplet-ullage heat and mass transfer, wherein droplets warm up to the saturation temperature corresponding to the ullage vapor pressure before evaporating while remaining at the saturation temperature. The evolution of tank pressure, vapor temperature, and liquid temperature predicted by the CFD model is validated against data from the MHTB spray-bar mixing experiment. Overall, the CFD models agree with experimental data, demonstrating their capability to simulate self-pressurization and pressure control processes in large-scale cryogenic storage tanks. These models can be valuable tools for designing and optimizing cryogenic fluid management systems in future applications.

Self-Pressurization↗

Simultaneous ultrasonic and synchrotron x-ray studies on pressure induced {alpha}-{omega} phase transition in zirconium

Compressional and shear wave velocities as well as unit-cell volumes across the {alpha}-{omega} transition of Zr have been measured up to 10.5 GPa at room temperature using ultrasonic interferometry in conjunction with synchrotron x radiation. In the pressure range of 5.0 to 6.2 GPa, a mixture of {alpha} and {omega} phase is clearly identified and the {alpha} phase is completely transformed to {omega} phase at 6.8 GPa. The measured velocity jumps across the {alpha}-{omega} transition are 9.6% and 13.1% for P and S waves, respectively. Negative pressure dependence for the shear modulus of {alpha}-Zr has been found at pressures from 1.4 to 2.9 GPa, which may be ascribed to the shear instability of the {alpha} phase prior to transition. According to velocity data, the onset pressure of the {alpha}-{omega} transition is determined to be {approx}4.0 GPa.

36 MATERIALS SCIENCE↗

Low-Pressure Electrochemical Synthesis of Complex High-Pressure Superconducting Superhydrides

There is great current interest in multicomponent superhydrides due to their unique quantum properties under pressure. A remarkable example is the ternary superhydride Li 2 MgH 16 computationally identified to have an unprecedented high superconducting critical temperature T c of ~470 K at 250 GPa. However, the very high synthesis pressures required remains a significant hurdle for detailed study and potential applications. In this Letter, we evaluate the feasibility of synthesizing ternary Li-Mg superhydrides by the recently proposed pressure-potential (P 2 ) method that uniquely combines electrochemistry and applied pressure to control synthesis and stability. Furthermore, the results indicate that it is possible to synthesize Li-Mg superhydrides at modest pressures by applying suitable electrode potentials. Using pressure alone, no Li-Mg ternary hydrides are predicted to be thermodynamically stable, but in the presence of electrode potentials, both Li 2 MgH 16 and Li 4 MgH 24 can be stabilized at modest pressures. Three polymorphs are predicted as ground states of Li 2 MgH 16 below 300 GPa, with transitions at 33 and 160 GPa. The highest pressure phase is superconducting, while the two at lower pressures are not. Our findings point out the potentially important role of the P 2 method in controlling phase stability of complex multicomponent superhydrides.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Probing and modeling of pressure-induced coordination transformation in borate glasses: Inelastic x-ray scattering study at high pressure

Here, we report on the in situ synchrotron inelastic x-ray scattering spectra of Na-borate glasses at high pressure up to 25 GPa. The pressure-induced boron coordination transformation from {sup [3]}B to {sup [4]}B is linear with pressure characterized by a single value of ({partial_derivative}{sup [3]}B/{partial_derivative}P){sub T}. Previous studies of Li-borate and pure-borate glasses show a nonlinear transformation with multiple ({partial_derivative}{sup [3]}B/{partial_derivative}P){sub T} values for different pressure ranges, revealing the important role cation field strength plays in densification and pressure-induced structural changes. Considering the distribution of the energy difference beween low- and high-pressure states ({Delta}{var_epsilon}) in the energy landscape and the variance of the ratio {Delta}{var_epsilon} to its pressure gradient ({partial_derivative}{Delta}{var_epsilon}/{partial_derivative}P){sub T} as a measure of network flexibility with pressure, an amorphous system with a large variance in {Delta}{var_epsilon} at 1 atm and/or a small ({partial_derivative}{Delta}{var_epsilon}/{partial_derivative}P){sub T} may undergo a gradual coordination transformation (e.g., Na borates). In contrast, a system with the opposite behavior (e.g., Li borates) undergoes an abrupt coordination transformation. The results and concepts of this study thus can shed light on opportunities to study the effect of composition on the nature of densification in low-z oxide and other archetypal glasses and melts.

43 PARTICLE ACCELERATORS↗

Sizing and Selection of Pressure Relief Valves for High-Pressure Thermal–Hydraulic Systems

This study covers the critical concerns related to the sizing, selection, installation, maintenance, and testing of pressure safety valves (PSVs). The aim is to ensure the safety of pressurized systems, hydrostatic transmission systems, and hydraulic plants, including process plants, thermal power plants, and nuclear reactor systems. PSVs are devices that ensure the safety and reliability of pressurized vessels, lines, and systems during overpressure events. The task of selecting which PSV features are of greatest value for a specific purpose is complex—especially in the design of a high-pressure experimental thermal–hydraulic facility for hydrostatic and transient testing of the reactor system—when the systems are in the design and development phases and require qualification and demonstration to prove that they have reached a given level of technological readiness. The present study highlights the required steps for users to follow the associated rules, guidelines, and recommendations. As a part of this research, case studies are presented to help readers better understand the applicable strategy and standards. A discussion and a review of PSV performance degradation and failure are summarized to provide a better understanding of varied process applications and conditions, including fluid flow dynamics, boundary-layer formation and pressure drops, gas bubble formation and collapse, geometric configurations, inlet/outlet piping, abrupt pressure fluctuations, and acoustic resonance. Moreover, this study discusses the servicing and testing of PSVs in a multiphase pressurized system. Overall, it provides a basic overview of how PSVs ensure the safety of pressurized systems, supported by case studies and industrial practices.

02 PETROLEUM↗

Pressure Effects on the Relaxation of an Excited Ethane Molecule in High-Pressure Bath Gases

Here, we use molecular dynamics to calculate the rotational and vibrational energy relaxation of C 2 H 6 in Ar, Kr, and Xe bath gases over a pressure range of 10 to 400 atm and at temperatures of 300 K and 800 K. The C 2 H 6 is instantaneously excited by 80 kcal/mol randomly distributed into both vibrational and rotational modes. The computed relaxation rates show little sensitivity to the identity of the noble gas in the bath. Vibrational relaxation rates show a non-linear pressure dependence at 300 K. At 800 K the reduced range of bath gas densities covered by the range of pressures do not yet show any non-linearity in the pressure dependence. Rotational relaxation is characterized with two relaxation rates. The slower rate is comparable to the vibrational relaxation rate. The faster rate has a linear pressure dependence at 300 K but an irregular, nonlinear pressure dependence at 800 K. To understand this, a model was developed based on approximating the periodic box used in the molecular dynamics simulations by an equal-volume collection of cubes where each cube is sized to allow only single occupancy by the noble gas or the molecule. Combinatorial statistics then leads to a pressure and temperature dependent analytic distribution of the bath gas species the molecule encounters in a collision. This distribution, the dissociation energy of molecule/bath gas complexes and bath gas clusters, and the computed energy release per collision combine to show that only at 300 K is the energy release sufficient to dissociate likely complexes and clusters. This suggests that persistent and pressure-dependent clusters and complexes at 800 K may be responsible for the non-linear pressure dependence of rotational relaxation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗