Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Particle Size”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Highly Durable and Active Pt/Sb-Doped SnO 2 Oxygen Reduction Reaction Electrocatalysts Produced by Atomic Layer Deposition

Platinum supported on mixed-metal oxides (MMOs) are a class of active and durable cathode catalysts for proton exchange membrane fuel cell (PEMFC) due to a combination of the high oxidative stability of the supports and strong-metal-support interactions (SMSI) that enable them to exceed the activity of Pt/C. Herein, we solve a significant remaining challenge with Pt/MMO systems, namely the relatively low surface area and porosity. This is achieved by dispersing nearly-uniform Pt clusters using atomic layer deposition (ALD) on highly conductive (6.2 S/cm) and stable antimony doped tin dioxide (ATO) support. ALD-Pt/ATO exhibited significantly higher electrochemically active surface area (ECSA) (74 m 2 /g) and oxygen reduction reaction (ORR) catalytic activity (102 mA/mg Pt at 0.9 V vs. RHE) compared to Pt/ATO synthesized using ethylene glycol (ECSA=31 m 2 /g Pt , mass activity=52 mA/mg Pt at 0.9 V vs. RHE) and formic acid reduction methods (ECSA=28 m 2 /g Pt , mass activity=46 mA/mg Pt at 0.9 V vs. RHE). Further characterization showed that wet chemical methods resulted in poorer Pt particle dispersion, poor control over Pt particle size distribution and chemical degradation of the support (during Pt deposition). Given the near-ideal Pt particle size distribution of the ALD-Pt/ATO, particle size growth and loss of ECSA was found to be minimal over the course of rigorous potential cycling. Thus, after 10,000 potential cycles between 1V and 1.5V vs. RHE, ALD-Pt/ATO and other Pt/ATOs were found to retain 100% of their initial ECSA compared to 57.6% retention for Pt/C. Upon testing in a H 2 /air PEMFC, following 1,000 potential cycles, the change in ALD-Pt/ATO performance was negligible while Pt/C exhibited a 68.2% loss of initial peak power density. Thus, ALD-Pt/ATO is an active and highly durable ORR electrocatalyst in PEMFCs under start-up-shut down conditions.

25 ENERGY STORAGE↗
DOE OSTI2024

Toward Rational Design of Nickel Catalysts for Thermocatalytic Decomposition of Methane for Carbon Dioxide-Free Hydrogen and Value-Added Carbon Co-Product: A Review

Thermocatalytic decomposition of methane provides opportunities for hydrogen (H2) production with no emission of carbon dioxide. However, high-value carbon products need to be produced for economic deployment of thermocatalytic decomposition and to achieve a minimum H 2 selling price below the U.S, Department of Energy target of $ 1/kg H 2 . In this review, we re-evaluate data on catalyst development reported in the literature and propose correlations between catalyst characteristics, catalytic stability, and properties of carbon co-products. In the first part of the review, growth mechanisms for carbon nanotubes using state-of-the-art chemical vapor deposition are reviewed to catalog the effects of catalyst characteristics, the influence of carbon sources, interactions between metal particles and supports, and metal particle sizes on carbon growth. In the second part, representative developments in mono-, bi-, and tri-metallic nickel catalysts are highlighted. We present kinetic analysis of reactions catalyzed by mono-metallic nickel catalysts, which generates a correlation between metal particle size and catalyst stability. Rational design of Ni-based catalysts for TCD of methane requires attention to the size of the metal particle and effective normalization of the reaction rates. Further attention to the distribution of the metal particle sizes may help identify catalyst properties that contribute longevity and selectivity to processes that use them. While it is tempting to focus on the highest valued carbon products (e.g., CNTs and CFs), analysis of the markets for other carbon products suggests that a more flexible approach may generate comparable returns without the risk associated with specialization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Steering the Methane Dry Reforming Reactivity of Ni/La 2 O 3 Catalysts by Controlled In Situ Decomposition of Doped La 2 NiO 4 Precursor Structures

The influence of A- and/or B-site doping of Ruddlesden-Popper perovskite materials on the crystal structure, stability, and dry reforming of methane (DRM) reactivity of specific A 2 BO 4 phases (A = La, Ba; B = Cu, Ni) has been evaluated by a combination of catalytic experiments, in situ X-ray diffraction, X-ray absorption spectroscopy (XAS), X-ray photoelectron spectroscopy (XPS), and aberration-corrected electron microscopy. At room temperature, B-site doping of La 2 NiO 4 with Cu stabilizes the orthorhombic structure ( Fmmm ) of the perovskite, while A-site doping with Ba yields a tetragonal space group ( I 4/ mmm ). We observed the orthorhombic-to-tetragonal transformation above 170 °C for La 2 Ni 0.9 Cu 0.1 O 4 and La 2 Ni 0.8 Cu 0.2 O 4 , slightly higher than for undoped La 2 NiO 4 . Loss of oxygen in interstitial sites of the tetragonal structure causes further structure transformations for all samples before decomposition in the temperature range of 400 °C-600 °C. Controlled in situ decomposition of the parent or A/B-site doped perovskite structures in a DRM mixture (CH 4 :CO 2 = 1:1) in all cases yields an active phase consisting of exsolved nanocrystalline metallic Ni particles in contact with hexagonal La 2 O 3 and a mixture of (oxy)carbonate phases (hexagonal and monoclinic La 2 O 2 CO 3 , BaCO 3 ). Differences in the catalytic activity evolve because of (i) the in situ formation of Ni-Cu alloy phases (in a composition of >7:1 = Ni:Cu) for La 2 Ni 0.9 Cu 0.1 O 4 , La 2 Ni 0.8 Cu 0.2 O 4 , and La 1.8 Ba 0.2 Ni 0.9 Cu 0.1 O 4 , (ii) the resulting Ni particle size and amount of exsolved Ni, and (iii) the inherently different reactivity of the present (oxy)carbonate species. Based on the onset temperature of catalytic DRM activity, the latter decreases in the order of La 2 Ni 0.9 Cu 0.1 O 4 ~ La 2 Ni 0.8 Cu 0.2 O 4 ≥ La 1.8 Ba 0.2 Ni 0.9 Cu 0.1 O 4 > La 2 NiO 4 > La 1.8 Ba 0.2 NiO 4 . Simple A-site doped La 1.8 Ba 0.2 NiO 4 is essentially DRM inactive. The Ni particle size can be efficiently influenced by introducing Ba into the A site of the respective Ruddlesden-Popper structures, allowing us to control the Ni particle size between 10 nm and 30 nm both for simple B-site and A-site doped structures. Hence, it is possible to steer both the extent of the metal-oxide-(oxy)carbonate interface and its chemical composition and reactivity. Counteracting the limitation of the larger Ni particle size, the activity can, however, be improved by additional Cu-doping on the B-site, enhancing the carbon reactivity. Exemplified for the La 2 NiO 4 based systems, we show how the delicate antagonistic balance of doping with Cu (rendering the La 2 NiO 4 structure less stable and suppressing coking by efficiently removing surface carbon) and Ba (rendering the La 2 NiO 4 structure more stable and forming unreactive surface or interfacial carbonates) can be used to tailor prospective DRM-active catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Realistic operation of two residential cordwood-fired outdoor hydronic heater appliances—Part 2: Particle number and size

The use of wood as a fuel for home heating is a concern from an environmental health and safety perspective as biomass combustion appliances emit high concentrations of particulate matter. Wood burning significantly contributes to wintertime particulate matter concentrations in many states in the northern United States. Of particular concern are outdoor wood-fired hydronic heaters. These devices are concerning as they tend to have very large combustion chambers and typical use patterns can result in long periods of low output, which result in an increased particulate matter emission rate relative to high heat output operating conditions. In this study, the performance of two hydronic heaters operating under different combustion conditions, including four different heat output categories approximately corresponding to categories I–IV denoted in Environmental Protection Agency Method 28 Outdoor Wood-fired Hydronic Heaters, and during start-up and reloading events were investigated. Measurements of flue gas particulate number concentration and size for particles with aerodynamic diameters between 0.006 and 10 µm were made using a dilution sampling system. The measured particle number concentration in the flue gas was between 0.71 and 420 million particles per cubic centimeter and was dependent on fuel loading and heat output. For each hydronic heater tested, the highest average particle concentration was found at the beginning of each test during the cold-start condition. Additionally, the majority of the particles had aerodynamic diameters less than 0.100 µm (particles of this size made up between 64% and 97% of all particles) and less than 1% of all particles had aerodynamic diameters greater than 1 µm for all phases. For particles in the accumulation mode, between 0.100 and 1 µm, the mean particle diameter was dependent on fuel loading and heat output.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Elucidating Processes Controlling Arctic Atmospheric Aerosol Sources, Aging, and Mixing States (Final Report)

Atmospheric aerosols play critical roles in the Earth’s energy budget, directly by scattering or absorbing solar and terrestrial radiation and indirectly by serving as seeds (nuclei) for cloud droplet and ice crystal formation and by depositing on snow and ice surface, thereby changing the surface albedo. These effects are dependent on aerosol particle size and chemical composition and impact the hydrological cycle as well. This project provided single-particle size and chemical composition measurements across the entire annual cycle in the high Arctic and in the Alaskan Arctic during fall – winter, addressing the most significant gaps in Arctic aerosol observational data. These needs were based on recent rapid sea ice loss across the entire Arctic, as well as the major annual delays in sea ice freeze-up during fall in the Chukchi Sea and increased wintertime sea ice fracturing in the Beaufort Sea, both off the North Slope of Alaska. Two DOE Atmospheric Radiation Measurement (ARM) field campaigns were conducted for atmospheric aerosol sampling. The Aerosols during the Polar Utqiagvik Night (APUN – ‘snow on ground’ in Iñupiaq) ARM field campaign at Utqagivik, Alaska was conducted from Oct. 28 – Dec. 22, 2018. Aerosol sizing instrumentation and a single-particle mass spectrometer were successfully deployed for size-resolved number concentration measurements and measurements of individual particle size and chemical composition, respectively. These results show the influence of locally-produced sea spray aerosol, with high cloud-forming potential, due to delayed sea ice freeze-up in the fall. During the 2019‐2020 international Multidisciplinary drifting Observatory for the Study of Arctic Climate (MOSAiC) expedition, daily atmospheric aerosol particles were collected aboard the German icebreaker Polarstern in the Central Arctic from Nov. 2019 – Oct. 2020. Sea salt aerosol and marine organics were observed year-round during MOSAiC with varying morphologies and sources. These findings are important because most Arctic models do not include a sea spray aerosol source, despite this source increasing with declining sea ice extent. In addition to collecting new samples and data, this project also conducted further analysis of previously collected single-particle chemical composition measurements within the North Slope of Alaska oil fields and at Utqiaġvik, AK, during Aug. – Sep. 2015 and 2016 field campaigns. This work resulted in the discovery of chemical reactions of oil field combustion emissions occurring within fog droplets across the North Slope of Alaska and forming secondary aerosol, showing the impact of Arctic oil field emissions beyond black carbon aerosol and greenhouse gases. In addition, the distribution of chemical species across the aerosol population within the oil fields was quantified, using these data and a previously development framework. We also presented the first ambient evidence of the collision of two atmospheric particles resulting in formation of an organic-coated ammonium sulfate particle of marine origin, which has implications for cloud formation with declining sea ice extent. Overall, this project has elucidated connections between seawater biogeochemistry, resource extraction activities, atmospheric composition, clouds, and the energy budget of the Arctic region. The results of this project are expected to improve weather and sea ice forecasting for security and development in the Arctic and beyond.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Nanoparticle Catalyst Formation and Subsequent Sintering: Size-Distribution Fundamental Understanding and Catalyst Control via Mechanism-Enabled Population Balance Modeling (Final Report)

The challenge of elucidating the chemical mechanisms by which nano- and other particles form, and then using those mechanisms to understand, analyze, and ideally predict particle-size and particle-size distributions, was undertaken. Thanks to multi-year, longer-term DOE support each of these challenges was successfully met. The community is now able to both predict, and control in cases where the underlying mechanism of particle formation has been determined, the key PS and PSD that are, in turn, critical properties that strongly influence the catalytic and other physical properties of nano- and larger particles across nature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Facile Interfacial Reduction Suppresses Redox Chemical Expansion and Promotes the Polaronic to Ionic Transition in Mixed Conducting (Pr,Ce)O 2−δ Nanoparticles

Mixed ionic/electronic conductors (MIECs) are essential components of solid-state electrochemical devices, such as solid oxide fuel/electrolysis cells. For efficient performance, MIECs are typically nanostructured, to enhance the reaction kinetics. However, the effect of nanostructuring on MIEC chemo-mechanical coupling and transport properties, which also impact cell durability and efficiency, has not yet been well understood. Here, in this work, Pr 0.2 Ce 0.8 O 2−δ (PCO20) nanopowders were prepared by coprecipitation, then sintered in a modified dilatometer at three different temperatures (600, 725, and 850 °C) for microstructure evolution, resulting in three samples with different average particle sizes (23, 30, and 53 nm). The chemical strain and electronic/ionic conductivity were then measured simultaneously on stable nanostructures in four isotherms from 550 to 400 °C with steps in pO 2 (1 to 10 –4 atm O 2 ). A microcrystalline bar was prepared and measured for comparison. Particle size reduction led to a monotonically decreasing isothermal redox chemical strain, confirmed by in situ high-temperature, controlled-atmosphere XRD measurements. The corresponding conductivity measurements provided defect chemical insight into the particle size-dependent chemical expansion behavior. The significant weakening of the pO 2 dependence and decreased activation energy for electrical conduction with decreasing particle size indicated a decrease in the reduction enthalpy of PCO, shifting the transition from (Pr) polaronic to ionic behavior to higher pO 2 . STEM-EELS measurements confirmed the majority of Pr was reduced to 3+ in the nanoparticles, while Ce remained 4+. These results demonstrate suppression of deleterious chemical expansion and tailoring of the dominant charge carrier simply through controlling the particle size, providing insights for MIEC microstructural design.

ceria↗
DOE OSTI2022

Characterization of the Emissions and Crystalline Silica Content of Airborne Dust Generated from Grinding Natural and Engineered Stones

Abstract In this study, we systematically characterized the airborne dust generated from grinding engineered and natural stone products using a laboratory testing system designed and operated to collect representative respirable dust samples. Four stone samples tested included two engineered stones consisting of crystalline silica in a polyester resin matrix (formulations differed with Stones A having up to 90wt% crystalline silica and Stone B up to 50wt% crystalline silica), an engineered stone consisting of recycled glass in a cement matrix (Stone C), and a granite. Aerosol samples were collected by respirable dust samplers, total dust samplers, and a Micro-Orifice Uniform Deposit Impactor. Aerosol samples were analyzed by gravimetric analysis and x-ray diffraction to determine dust generation rates, crystalline silica generation rates, and crystalline silica content. Additionally, bulk dust settled on the floor of the testing system was analyzed for crystalline silica content. Real-time particle size distributions were measured using an Aerodynamic Particle Sizer. All stone types generated similar trimodal lognormal number-weighted particle size distributions during grinding with the most prominent mode at an aerodynamic diameter of about 2.0-2.3 μm, suggesting dust formation from grinding different stones is similar. Bulk dust from Stone C contained no crystalline silica. Bulk dust from Stone A, Stone B, and granite contained 60, 23, and 30wt% crystalline silica, respectively. In Stones A and B, the cristobalite form of crystalline silica was more plentiful than the quartz form. Only the quartz form was detected in granite. The bulk dust, respirable dust, and total dust for each stone had comparable amounts of crystalline silica, suggesting that crystalline silica content in the bulk dust could be representative of that in respirable dust generated during grinding. Granite generated more dust per unit volume of material removed than the engineered stones, which all had similar normalized dust generation rates. Stone A had the highest normalized generation rates of crystalline silica, followed by granite, Stone B, and Stone C (no crystalline silica), which likely leads to the same trend of respirable crystalline silica (RCS) exposure when working with these different stones. Manufacturing and adoption of engineered stone products with formulations such as Stone B or Stone C could potentially lower or eliminate RCS exposure risks. Combining all the effects of dust generation rate, size-dependent silica content, and respirable fraction, the highest normalized generation rate of RCS consistently occurs at 3.2-5.6 µm for all the stones containing crystalline silica. Therefore, removing particles in this size range near the generation sources should be prioritized when developing engineering control measures.

Public, Environmental & Occupational Health↗
DOE OSTI2024

Evaluation of methods for characterizing the fine particulate matter emissions from aircraft and other diffusion flame combustion aerosol sources

The U. S. Environmental Protection Agency in collaboration with the U. S. Air Force Arnold Engineering Development Complex conducted the VAriable Response In Aircraft nvPM Testing (VARIAnT) 3 and 4 test campaigns to compare nvPM emissions measurements from a variety of diffusion flame combustion aerosol sources (DFCASs), including a Cummins diesel engine, a diesel powered generator, two gas turbine start carts, a J85-GE-5 turbojet engine burning multiple fuels, and a Mini-CAST soot generator. The VARIAnT research program has conducted four test campaigns to date with the VARIAnT 3 and 4 test campaigns focusing on BC mass instrument performance, use of gas turbine engine sources for BC mass instrument calibration, and the characterization of the aerosols produced from the combustion sources. Results from both campaigns revealed agreement of about 20% between the AVL Micro-Soot Sensor, the Cavity Attenuated Phase Shift (CAPS PMSSA) monitor and the thermal-optical reference method for elemental carbon (EC), independent of the calibration source used. For the Artium LII-300, the measured mass concentrations in VARIAnT3 fall within 18% and in VARIAnT4 fall within 32% of the reference EC mass concentration when calibrated on a combustor rig in VARIAnT3 and on a LGT-60 start cart in VARIAnT4, respectively. It was also found that the three mass instrument types (MSS, CAPS PMSSA, and LII-300) can exhibit different BC to reference EC ratios depending on the emission source that appear to correlate to particle geometric mean mobility diameter, morphology, or some other parameter associated with particle geometric mean diameter (GMD) with the LII-300 showing a slightly stronger apparent trend with GMD. Systematic differences in LII-300 measured mass concentrations have been reduced by calibrating with a turbine combustion source (combustor or turbine engine). With respect to the particle size measurements made, the sizing instruments (TSI SMPS, TSI EEPS, and Cambustion DMS 500) were found to be in general agreement in terms of size distributions and concentrations with some exceptions. Teflon filter measurements of the total aerosol mass produced by the various DFCASs differed from the reference EC, BC, and integrated particle sized distribution measured aerosol masses. The Teflon filter measured mass was 30 to 40% greater than the reference EC and 50 to 60% greater than the BC mass for the J85 in both test campaigns. The measurements of particle size distributions and single particle analysis by miniSPLAT indicated the presence of large particles (>100 nm) having more compact morphologies, higher effective density, and a composition dominated by OC and ash. This increased large particle fraction is also associated with higher values of single scattering albedo measured by the CAPS PMSSA instrument and higher OC/EC measurements. These measurements indicate gas turbine engine emissions can be a more heterogeneous mix of particle types beyond the original E31 assumption that it is mainly composed of black carbon.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Paper or Plastic? Multiscale Material Handling Properties of Two Model Municipal Solid Waste Streams

Purpose: Municipal Solid Waste (MSW) is a potentially valuable sustainable feedstock for fuel and chemical production due to its carbon-rich content and low cost. This study aims to assess the material handling properties of paperand plastic-rich MSW feedstocks to mitigate equipment failure and processing downtime. Methods: The material handling properties of crumbled MSW feedstocks were measured using apowder rheometer with mass flow hopper calculations to assess handling performance. Inverse gas chromatography was use to measure the surface energy differences between feedstocks. Electron microscopy and Raman spectroscopy was used to evaluate microscale features that may contribute to material handling differences. Results: Plastic and paper rich feedstocks crumbled to a nominal 2 mm particle size were observed to have similar flow and handling characteristics with reasonable hopper outlets. 2 mm plastic rich crumbles, with their higher bulk density, exhibited superior flow performance. By contrast, 4 mm material required significantly larger hopper outlets, indicating poor flowability. Paper rich and 4 mm plastic rich samples displayed broad particle size distributions, which contributed to particle interlocking, jamming, and other flow issues. Electron microscopy revealed that plastic rich samples were significantly smoother, enhancing their flowability compared to the rougher, paper rich materials. Conclusions: This study establishes critical material handling baselines for processing MSW as a viable feedstock for fuel and chemical production. The findings highlight the importance of optimizing particle size and feedstock composition to improve flowability and handling performance.

09 BIOMASS FUELS↗
DOE OSTI2025

Role of Pb/PbSO 4 Morphologies in Dynamic Charge Acceptance of Lead Acid Batteries

The dynamic charge acceptance (DCA) of negative pastes in lead acid batteries is studied using a continuum level model that is validated against in situ X-ray diffraction experiments. The model matches the current transient during a ten-minute, 2.4 V charge at 80% state of charge (SOC) using a distribution of PbSO 4 particles. <2% by volume of small, reactive particles is shown to provide ∼50% of the capacity during the first ten seconds. Increases in DCA with increasing carbon content are captured with increasing lead surface area. The increase in DCA when the 2.4 V charge is done after discharging to 80% SOC (vs charging to 80%) is captured by reducing the PbSO 4 particle sizes. It is hypothesized that the lower DCA after charging is caused by the absence of smaller particles that were consumed during the initial charge to 80% SOC, which is confirmed from X-ray measurements. Finally, two-particle case studies show that reducing the PbSO 4 particle size is more effective for increasing DCA than increasing the PbSO 4 dissolution rate alone. For a given lead surface area, the optimal DCA occurs when the particle sizes are large enough to avoid blocking the surface but small enough to provide dissolution/diffusion improvements.

Knehr, Kevin W. [Argonne National Laboratory (ANL)↗
DOE OSTI2025

Resonance-stabilized radical clustering bridges the gap between gaseous precursors and soot in the inception stage

Carbonaceous particles are widespread in combustion, atmospheric, extraterrestrial, and nanomaterials environments. Resonance-stabilized radicals (RSRs) are commonly identified in fuel combustion and pyrolysis processes and play an essential role in carbonaceous particle formation. Despite their importance, comprehensive experimental and mechanistic understanding of particle inception through RSR reactions is lacking. This work investigated particle size distribution, chemical composition, and thermal behavior of soot particles generated by the flow reactor pyrolysis reactions of typical RSRs, in particular, 1-indenyl, 1-methylnaphthyl, and 2-methylnaphthyl radicals, and by the pyrolysis of hydrocarbons with a variety of structures. Particle size distributions show soot particles with mobility diameters in an incipient-particle range of 1.3 to 1.6 nm. Laser desorption/ionization mass spectrometry results suggest that soot products consist of much larger covalently bound clusters (CBCs) than those observed in the gas phase. Under our experimental conditions, the CBCs exhibit a phase transition for particles with calculated molecular diameters of around 1.5 nm. Evaporation experiments and thermogravimetric analysis of the soot products reveal distinct thermal characteristics for small and large CBCs. These results implicate CBCs as bridges between gas-phase species and soot particles. The present work provides a soot-inception mechanism called RSR clustering (RSRC) that is characterized by the reactive clustering of RSRs. The RSRC mechanism contrasts with conventional soot formation models that attribute soot inception primarily to the aggregation of large-size polycyclic aromatic hydrocarbons.

carbonaceous particle↗
DOE OSTI2023

Model-Free Approach for Profiling of Polydisperse Soft Matter Using Small Angle Scattering

A strategy for determining the size polydispersity of systems from their small angle coherent scattering is outlined. Here, using the method of moment expansion, we show that the various central moments representing the average particle size, variance of particle size, and skewness of size distribution function (SDF) for polydisperse systems can be extracted from spectral analysis without bias. When the degree of polydispersity is moderate, SDF can be further reconstructed based on the maximum entropy principle. Numerical benchmarking of a model study over a wide range of size nonuniformity demonstrates the validity of this analytical approach for quantifying the size distribution of general soft matter systems in a model-free manner. Furthermore, the efficacy of this method was validated by successfully applying it to the fitting of small-angle neutron scattering data obtained from L64 Pluronic micelles using various form factor models. The numerical and experimental verification underscores the reliability and versatility of this method in accurately characterizing the size distribution of complex soft matter systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Operando X-ray imaging reveals size-dependent evolution of cobalt oxide thermochemical material during thermal redox cycles

Multivalent metal oxides are promising thermochemical materials (TCMs) for energy storage and conversion owing to their high energy density, air compatibility, and high-temperature stability. Co 3 O 4 serves as a model system for examining particle-size- and structure-dependent redox behavior. While particle size and porosity are known to affect performance, their interplay and the kinetics of pore formation during cycling remain unclear. Here we show the chemical and 3D morphological evolution of Co 3 O 4 micro- and nanoparticles during redox cycles at 800–900 °C using thermal analysis, in-situ synchrotron transmission X-ray microscopy (TXM), and scanning electron microscopy. Thermal analysis shows that nanoparticles re-oxidize more rapidly than microparticles at 800 °C. In-situ nanotomography and chemical imaging reveals that nanoparticles undergo redox conversion without forming internal pores, whereas microparticles develop isolated porosity during reduction. These pores persist through re-oxidation, correlating to a lower conversion rate in subsequent cycles. Our results demonstrate distinct degradation kinetics in Co 3 O 4 micro- and nanoparticles, underscoring the critical role of particle size and porosity in redox performance and informing strategies to enhance the long-term efficiency of metal oxide TCMs.

25 ENERGY STORAGE↗
DOE OSTI2023

Particle number size distributions (10-461 nm) measured by SMPS at the ENA site during the AGENA campaign

During the Aerosol Growth in the Eastern North Atlantic (AGENA) campaign at the ENA site, particle number size distributions ranging from 10.6 to 461 nm were measured using SMPS with a time resolution of 4 minutes. The local pollution was identified and flagged by the “pollutionflag” field, where 0 denotes the clean periods and 1 denotes the polluted periods.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Spectral gratings-based phase-contrast imaging for materials characterization

Spectral X-ray detectors provide a direct observation of the energy spectrum of a transmitted X-ray beam, both for typical and phase-contrast gratings-based systems. The sensitivity of a gratings-based X-ray system to small-angle deflections from a given particle size is dependent on X-ray energy. Therefore, spectral (energy-sensitive) detectors could be sensitive to particle size, even with a broad spectrum from a commercial X-ray generator. Furthermore, these detectors allow direct observation of how the X-ray spectrum is changing as the beam is passing through an object and gratings, and how this affects grating visibilities used to determine the presence of small-angle deflections. This is a particular issue for higher-energy systems where artifacts from beam hardening are common. We present results exploring the particle-size dependent signatures that are available from a spectral gratings-based phase-contrast X-ray imaging system, and the feasibility of observing them with lab-based, broad-spectrum X-ray generators.

Gilbert, Andrew J.↗
DOE OSTI2021

Reduction of Ultrafine Hematite for a Spouting Bed Chemical Looping Process - Presentation

Chemical looping combustion research has been a topic of great interest since the mid-1990s, although the concept can be traced much further back. It is a combustion technology for fuel utilization that uses a two-reactor system to produce a carbon free effluent stream from the air reactor and a carbon dioxide rich stream from the fuel reactor with oxygen shuttled between the reactors with an oxygen carrier. Chemical looping combustion has been studied extensively because of this inherent separation of the carbon dioxide combustion product from the atmospheric nitrogen over that past 25 years with hundreds of research papers and tens of books. The oxygen carrier is, in general, a solid such as naturally occurring hematite or an engineered carrier like a copper and iron oxide supported on alumina. System technical and economic research activities conducted at the National Energy Technology Laboratory have shown that the costs associated with the carrier, initial and replacement, are a significant factor in the economic viability of the technology. To overcome this economic challenge, the work reported on in this paper investigates the use of a waste iron oxide as the chemical looping oxygen carrier. This waste material is quite unique as it has a particle size of 0.7 um. Given the particle size, the reactions are quite fast. However, the development of a contactor reactor to mix the fuel with the carrier is a fluidization challenge as the material is a Geldart group C material and highly cohesive. Normally, Geldart group C materials are fluidized with either a vibrating bed. This technique is acceptable for low temperature pharmaceuticals production but does not lend itself to much larger reactors used for power production or operation at temperatures in the order of 1100 to 1200 C. Therefore, a hydrodynamic solution was needed to break up the cohesive structures to replace the vibration. In this instance, it was hypothesized that a spouting bed of large Geldart group B or Geldart group D particles could provide the necessary energy to break up the cohesive structures of the Geldart group C material. This paper presents the reduction performance for this novel carrier material in a laboratory spouting bed reactor.

Breault, Ronald↗
DOE OSTI2024

Direct numerical simulation of open-channel flow over a heterogeneous particle bed at low relative submergence

In this article, this study investigates turbulent open-channel flows over beds of irregularly arranged particles, using direct numerical simulations at a friction Reynolds number of Re T = 300⁠. Two distinct cases are examined: a polydisperse bed (P800) composed of multiple layers of randomly distributed spheres of varying sizes, and a monodisperse bed (M1015) formed by a random distribution of uniform sized spheres, with a bottommost single layer of varied-sized particles to introduce realistic randomness. Our investigation unveils a rich network of low- and high-speed streaks within the flow field, exhibiting distinctive behaviors in different bed configurations. The P800 case presents a poorly organized flow pattern induced by the varied particle sizes and arrangements, while the M1015 case shows a more regular flow pattern, marked by larger streaks. We also observe that total wall shear stress is substantially influenced by surface roughness-induced drag, extending beyond the effects documented in existing studies of open-channel flows. The present study reveals intricate secondary flow patterns over irregular particle beds. Large-scale circulations are discerned around particle crests in the P800 case and localized circulations with increased turbulence in the M1015 case. Furthermore, analysis of Reynolds stress tensor components indicates that roughness disrupts coherent turbulent eddies, consequently mitigating peak stress. We quantify correlations between drag force and local fluid velocity fluctuations. Notably, a larger deviation in drag is observed in the P800 case compared to M1015, accentuating the influence of particle size and distribution on fluid–particle interactions.

42 ENGINEERING↗