Gas-Density Gage
Lightweight density gage that operates over broad pressure range accurately measures gas pressures.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Lightweight density gage that operates over broad pressure range accurately measures gas pressures.
This paper describes the Hot Gas Facility, a unique, reliable, and cost-effective high-heat-flux facility for testing hypersonic engine components developed at the NASA Lewis Research Center. The Hot Gas Facility is capable of providing heat fluxes ranging from 200 Btu/sq ft per sec on flat surfaces up to 8000 Btu/sq ft per sec at a leading edge stagnation point. The usefulness of the Hot Gas Facility for the NASP community was demonstrated by testing hydrogen-cooled structures over a range of temperatures and pressures. Ranges of the Reynolds numbers, Prandtl numbers, enthalpy, and heat fluxes similar to those expected during hypersonic flights were achieved.
Effective thermal conductivity of a high porosity unbonded silica fibrous insulation specimen was measured over a pressure range of 0.001 to 750 torr (0.1 to 101.3 x 10(exp 3) Pa), and with large temperature gradients maintained across the sample thickness: hot side temperature range of 360 to 1360 K, with the cold side at room temperature. The measurements were compared with the theoretical solution of combined radiation/conduction heat transfer. The previously developed radiation heat transfer model used in this study is based on a modified diffusion approximation, and uses deterministic parameters that define the composition and morphology of the medium: distributions of fiber size and orientation, fiber volume fractions, and the spectral complex refractive index of the fibers. The close agreement between experimental and theoretical data further verifies the theoretical model over a wide range of temperatures and pressures.
A new Direct Numerical Simulation (DNS) of Couette-Poiseuille flow at a higher Reynolds number is presented and compared with DNS of other wall-bounded flows. It is analyzed in terms of testing semi-theoretical proposals for universal behavior of the velocity, mixing length, or eddy viscosity in pressure gradients, and in terms of assessing the accuracy of two turbulence models. These models are used in two modes, the traditional one with only a dependence on the wall-normal coordinate y, and a newer one in which a lateral dependence on z is added. For pure Couette flow and the Couette-Poiseuille case considered here, this z-dependence allows some models to generate steady streamwise vortices, which generally improves the agreement with DNS and experiment. On the other hand, it complicates the comparison between DNS and models.
We have stabilized two new cubic (3C structured) A{sub 2}B′B′′O{sub 6}-type double-perovskite phases, Ba{sub 2}CoSbO{sub 6} and Ba{sub 2}ZnTeO{sub 6}, by means of a high-pressure heat-treatment of corresponding hexagonal (6H and 12R structured, respectively) non-perovskite phases at 4 GPa and 1000 °C. Similar treatments on hexagonal Ba{sub 2}TiMnO{sub 6} (12R) and Ba{sub 2}NiTeO{sub 6} (12R) phases did not yield the 3C double-perovskite structure but converted the 12R structure to the 6H structure. The pressure-induced phase conversion in each A{sub 2}B′B′′O{sub 6} system apparently goes from the 12R structure towards the 6H and 3C structures with increasing pressure, where the pressure ranges required most likely depend (among other possible factors) on the tolerance factor for the particular combination of A, B′ and B′′. We foresee that yet a number of novel B-site ordered double-perovskite compounds are to be discovered through the high-pressure high-temperature treatment. - Graphical abstract: High-pressure (HP) heat-treatment is an efficient tool to synthesize novel B-site ordered double-perovskite materials. This is demonstrated for two new cubic (3C structured) perovskite phases, Ba{sub 2}CoSbO{sub 6} and Ba{sub 2}ZnTeO{sub 6}, obtained through a HP conversion of corresponding hexagonal (6H and 12R structured, respectively) non-perovskite phases at 4 GPa and 1000 °C. Similar treatments on hexagonal Ba{sub 2}TiMnO{sub 6} (12R) and Ba{sub 2}NiTeO{sub 6} (12R) phases yield the intermediate 6H structure.
The supercritical water mixing phenomenon is investigated with a wide range of conditions, i.e. the inlet temperature of the streams ranges from 323.15 K to 723.15 K and the pressure ranges from 25 MPa to 45 MPa. A sensitivity study is carried out for the jet and main flow velocity ratio (VR) which is varying from 1 to 40. In addition, the effect of the inject angles of branch flow to main flow on the mixing is conducted by varying the inject angle from 80 deg. to 100 deg.. The results show that the maximum temperature gradient appears on the wall of the upstream side in all the cases, and the inclined angles can be optimized to mitigate the thermal stress. (authors)
Tritium is generated by the interaction of neutrons with the lithium and beryllium in the molten salt reactors (MSRs), which use FLiBe as one of solvents of fluoride fuel. Tritium as by-product in the MSRs is an important safety issue because it could easily diffuse into environment through high temperature heat exchangers. The experimental technique of gas driven permeation has been used to investigate the transport parameter of hydrogen in Hastelloy C-276 which is considered as one of the candidate for structure materials. The measurements were carried out at the temperature range of 400-800 Celsius degrees with hydrogen loading pressures ranging from 5*10{sup 3} to 4*10{sup 4} Pa. The H diffusive transport parameters for Hastelloy C-276 follow an Arrhenius law in this temperature range. Regarding diffusivity and Sieverts' constant, Hastelloy C-276 has lower values compared with Ni201 alloy. The possible reason may be the trapping effects, which were formed by the alloying elements of Mo and Cr in the matrix. At the same time, the thin oxidation layer formed by the high Cr content could lead to a slower dissociation process of H{sub 2} at the surface. (authors)
Films of LiMn{sub 2}O{sub 4} prepared by pulsed laser ablation deposition are typically lithium deficient when grown at background pressures ranging between 10{sup -4} and 20 Pa. The deficiency of light atomic species such as lithium in LiMn{sub 2}O{sub 4} thin films occurs as a result of the different behavior of the species during plume expansion and the deposition of the film at elevated deposition temperatures. The plasma plume evolution in vacuum and 20 Pa oxygen pressure are studied using two spectroscopic techniques: emission spectroscopy and plume imaging. Higher velocities and a wider spatial distribution of lithium atoms are observed in vacuum when compared with manganese and oxygen species. Plume species are slowed down due to collisions with gas molecules when ablating LiMn{sub 2}O{sub 4} in an oxygen atmosphere. As a result, a strong deceleration of the plasma front occurs, and the effect is more pronounced for the light species, e.g., Li. Comparing the spatial manganese and lithium distribution within the plasma, the lithium species are again scattered into a wider angular range. These similar spatial distributions of Li atoms detected in the pressure range between 10{sup -4} and 20 Pa suggest that it is not possible to achieve a congruent lithium transfer to a growing film if the target contains heavier elements besides lithium. The general implications for the ablation of materials containing a combination of light and heavy elements are that as-grown films are inherently deficient with respect to the content of the light elements. If the mass ratio between the light and the heavy elements is not too different, is should be possible to find a set of deposition parameters which will result in the growth of a film with the desired composition.
The elastic behavior of H-ZSM-5 was investigated by in-situ synchrotron X-ray powder diffraction, using both silicone oil (s.o.) and (16:3:1) methanol:ethanol:water (m.e.w.) as 'non-penetrating' and 'penetrating' pressure transmitting media, respectively. From P{sub amb} to 6.2 GPa the volume reduction observed in s.o. is 16.6%. This testifies that H-ZSM-5 is one of the most flexible microporous materials up to now compressed in s.o. Volume reduction observed in m.e.w. up to 7.6 GPa is 14.6%. A strong increase in the total electron number of the extraframework system, due to the penetration of water/alcohol molecules in the pores, is observed in m.e.w. This effect is the largest up to now observed in zeolites undergoing this phenomenon without cell volume expansion. The higher compressibility in s.o. than in m.e.w. can be ascribed to the penetration of the extra-water/alcohol molecules, which stiffen the structure and contrast the channel deformations. - Graphical abstract: High-pressure behavior of H-ZSM-5 compressed in (16:3:1) methanol:ethanol:water: (a) projection of the structure along the [0 1 0] direction at P{sub amb}, 2 GPa and after pressure release to original ambient conditions (P{sub amb} (rev)), and (b) P-dependence of the extraframework content expressed as total number of electrons (gray square represents the number of the extraframework electrons at P{sub amb} after decompression). Highlights: > X-ray powder diffraction study of H-ZSM-5 compressibility. > H-ZSM-5 is one of the softest porous material compressed in silicon oil. > Penetration of additional water/alcohol molecules upon compression in m.e.w. > Extra molecules contribute to stiffen the structure and to contrast HP effects.
We describe the development and test of an elevated pressure and temperature rotating disk electrode (RDE) system that allows measurements under well-defined mass transport conditions. As demonstrated for the oxygen reduction reaction on polycrystalline platinum (Pt) in 0.5M H{sub 2}SO{sub 4}, the setup can easily be operated in a pressure range of 1–101 bar oxygen, and temperature of 140 °C. Under such conditions, diffusion limited current densities increase by almost two orders of magnitude as compared to conventional RDE setups allowing, for example, fuel cell catalyst studies under more realistic conditions. Levich plots demonstrate that the mass transport is indeed well-defined, i.e., at low electrode potentials, the measured current densities are fully diffusion controlled, while at higher potentials, a mixed kinetic-diffusion controlled regime is observed. Therefore, the setup opens up a new field for RDE investigations under temperature and current density conditions relevant for low and high temperature proton exchange membrane fuel cells.
SF{sub 6} gas is widely used in the high voltage circuit breakers but considering its high global warming potential other substitutes are being sought. Among them CO{sub 2} was investigated and even has been used in some practical products. However, at room temperature, the dielectric properties of CO{sub 2} are relatively lower than SF{sub 6} and air. The goal of this work is to investigate a CO{sub 2}-based gas to improve the performance of the pure CO{sub 2}. In this paper, the dielectric properties of hot CO{sub 2}/O{sub 2} mixtures related to the dielectric recovery phase of the circuit breaker were investigated in the temperature range from 300 K to 4000 K and in the pressure range from 0.01 MPa to 1.0 MPa. The species compositions of hot CO{sub 2}/O{sub 2} were obtained based on Gibbs free energy minimization under the assumptions of local thermodynamic equilibrium and local chemical equilibrium. The reduced critical electric field strength of CO{sub 2}/O{sub 2} was determined by balancing electron generation and loss. These were calculated using the electron energy distribution function by solving the Boltzmann transport equation. The validity of the calculation method and the cross sections data was confirmed by comparing the measurements and calculations of the electron swarm data in previous work. The results indicate that in pure CO{sub 2} the critical electric field strength is higher only in higher temperature range. By adding the O{sub 2} into the CO{sub 2}, the critical electric field strength at lower temperature is effectively enhanced. CO{sub 2}/O{sub 2} mixtures have a much better dielectric strength than both the pure CO{sub 2} and air and thus have the potential to improve the CO{sub 2}-based gas circuit breakers. Similar conclusions can also be found in others’ work, which further confirm the validity of these results.
The self-diffusion of ice VII in the pressure range of 5.5–17 GPa and temperature range of 400–425 K was studied using micro Raman spectroscopy and a diamond anvil cell. The diffusion was monitored by observing the distribution of isotope tracers: D{sub 2}O and H{sub 2}{sup 18}O. The diffusion coefficient of hydrogen reached a maximum value around 10 GPa. It was two orders of magnitude greater at 10 GPa than at 6 GPa. Hydrogen diffusion was much faster than oxygen diffusion, which indicates that protonic diffusion is the dominant mechanism for the diffusion of hydrogen in ice VII. This mechanism is in remarkable contrast to the self-diffusion in ice I{sub h} that is dominated by an interstitial mechanism for the whole water molecule. An anomaly around 10 GPa in ice VII indicates that the rate-determining process for the proton diffusion changes from the diffusion of ionic defects to the diffusion of rotational defects, which was suggested by proton conductivity measurements and molecular dynamics simulations.
This work investigates the cold compaction behavior of Ti-6Al-4V powders produced by Armstrong Process . As-received as well as milled powders were characterized and these powders were uniaxially die-pressed at designated pressures up to 690 MPa to form disk samples with different aspect ratios. Samples with high aspect ratio exhibited non-uniform density along the pressing axis and the density distribution is in consistent with the result predicted by finite element analysis. The linear regression analysis on the experimental density data can be used to predict density of compacts with different aspect ratios. In the studied pressure range, an empirical powder compaction equation represents the green density pressure relationship very well for both the as-received and 1-hr milled Armstrong Ti-6Al-4V powders.
Tbe spin-density-wave (SDW) anti ferromagnet CaFe{sub 2}As{sub 2} becomes superconducting under pressure. By measuring electrical resistivity and magnetic susceptibility under pressure, we show that bulk superconductivity is present in a narrow pressure range where a collapsed tetrgaonal structure is favored. At higher pressures, a new low-temperature structure appears, with the boundary between this new structure and the collapsed tetragonal structure strongly dependent on pressure history. Magnetic fluctuations in the collapsed phase appear to be important for superconductivity.
Accelerated carbonation is induced in pastes and mortars produced from alkali silicate-activated granulated blast furnace slag (GBFS)-metakaolin (MK) blends, by exposure to CO{sub 2}-rich gas atmospheres. Uncarbonated specimens show compressive strengths of up to 63 MPa after 28 days of curing when GBFS is used as the sole binder, and this decreases by 40-50% upon complete carbonation. The final strength of carbonated samples is largely independent of the extent of metakaolin incorporation up to 20%. Increasing the metakaolin content of the binder leads to a reduction in mechanical strength, more rapid carbonation, and an increase in capillary sorptivity. A higher susceptibility to carbonation is identified when activation is carried out with a lower solution modulus (SiO{sub 2}/Na{sub 2}O ratio) in metakaolin-free samples, but this trend is reversed when metakaolin is added due to the formation of secondary aluminosilicate phases. High-energy synchrotron X-ray diffractometry of uncarbonated paste samples shows that the main reaction products in alkali-activated GBFS/MK blends are C-S-H gels, and aluminosilicates with a zeolitic (gismondine) structure. The main crystalline carbonation products are calcite in all samples and trona only in samples containing no metakaolin, with carbonation taking place in the C-S-H gels of all samples, and involving the free Na{sup +} present in the pore solution of the metakaolin-free samples. Samples containing metakaolin do not appear to have the same availability of Na{sup +} for carbonation, indicating that this is more effectively bound in the presence of a secondary aluminosilicate gel phase. It is clear that claims of exceptional carbonation resistance in alkali-activated binders are not universally true, but by developing a fuller mechanistic understanding of this process, it will certainly be possible to improve performance in this area.
This article discusses the influence of compressive shock waves on the permeability of cementitious materials. Shock waves are generated in water by Pulsed Arc Electrohydraulic Discharges (PAED). The practical aim is to increase the intrinsic permeability of the specimens. The maximum pressure amplitude of the shock wave is 250 MPa. It generates damage in the specimens and the evolution of damage is correlated with the intrinsic permeability of the mortar. A threshold of pressure is observed. From this threshold, the increase of permeability is linear in a semi-log plot. The influence of repeated shocks on permeability is also discussed. Qualitative X Ray Tomography illustrates the evolution of the microstructure of the material leading to the increase of permeability. Comparative results from mercury intrusion porosimetry (MIP) show that the micro-structural damage process starts at the sub-micrometric level and that the characteristic size of pores of growing volume increases.
The purpose of this study is to evaluate the environment performance of high-strength concrete used in super tall buildings as material of environmental load reduction. To this end, this study proposed a plan for the evaluation of energy consumption and CO{sub 2} emission throughout the life cycle of the building, and calculated the energy consumption and CO{sub 2} emission throughout the life cycle of tall apartment building that was actually constructed using this plan. Then, we evaluated the energy consumption and CO{sub 2} emission reduction performance for the life cycle of the building by the decrease of concrete and reinforced rebar quantities and the increase of building lifespan obtained through conversion of existing building's concrete compressive strength to 40 MPa high-strength concrete. As a result, the life cycle energy consumption in case 3, a high-strength concrete building, decreased 15.53% and 2.95% respectively compared with cases 1 and 2. The evaluation of the general strength concrete buildings and the life cycle CO{sub 2} emission also decreased 16.70% and 3.37% respectively, compared with cases 1 and 2.