Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PELLETING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

A compact flexible pellet injector for the TJ-II stellarator

A compact pellet injector is being built for the TJ-II stellarator. It is an upgraded version of the 'pellet injector in a suitcase' developed at Oak Ridge National Laboratory and installed on the Madison Symmetric Torus where it continues to be used in many plasma experiments. The design aim is to provide maximum flexibility at minimal cost, while allowing for future upgrades. It is a four-barrel system equipped with a cryogenic refrigerator for in situ hydrogen pellet formation, a combined mechanical punch/propellant valve system, pellet diagnostics, and an injection line, destined for use as an active diagnostic and for fueling. In order to fulfill both objectives it will be sufficiently flexible to permit pellets, with diameters from 0.4 to 1 mm, to be fabricated and accelerated to velocities from 150 to {approx}1000 m s{sup -1}.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The enhanced ASDEX Upgrade pellet centrifuge launcher

Pellets played an important role in the program of ASDEX Upgrade serving both for investigations on efficient particle fuelling and high density scenarios but also for pioneering work on Edge Localised Mode (ELM) pacing and mitigation. Initially designed for launching fuelling pellets from the magnetic low field side, the system was converted already some time ago to inject pellets from the magnetic high field side as much higher fuelling efficiency was found using this configuration. In operation for more than 20 years, the pellet launching system had to undergo a major revision and upgrading, in particular of its control system. Furthermore, the control system installed adjacent to the launcher had to be transferred to a more distant location enforcing a complete galvanic separation from torus potential and a fully remote control solution. Changing from a hybrid system consisting of PLC S5/S7 and some hard wired relay control to a state of the art PLC system allowed the introduction of several new operational options enabling more flexibility in the pellet experiments. This article describes the new system architecture of control hardware and software, the operating procedure, and the extended operational window. First successful applications for ELM pacing and triggering studies are presented as well as utilization for the development of high density scenarios.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impact of Sequential Ammonia Fiber Expansion (AFEX) Pretreatment and Pelletization on the Moisture Sorption Properties of Corn Stover

Combining ammonia fiber expansion (AFEX™) pretreatment with a depot processing facility is a promising option for delivering high-value densified biomass to the emerging bioenergy industry. However, because the pretreatment process results in a high moisture material unsuitable for pelleting or storage (40% wet basis), the biomass must be immediately dried. If AFEX pretreatment results in a material that is difficult to dry, the economics of this already costly operation would be at risk. This work tests the nature of moisture sorption isotherms and thin-layer drying behavior of corn (Zea mays L.) stover at 20°C to 60°C before and after sequential AFEX pretreatment and pelletization to determine whether any negative impacts to material drying or storage may result from the AFEX process. The equilibrium moisture content to equilibrium relative humidity relationship for each of the materials was determined using dynamic vapor sorption isotherms and modeled with modified Chung-Pfost, modified Halsey, and modified Henderson temperature-dependent models as well as the Double Log Polynomial (DLP), Peleg, and Guggenheim Anderson de Boer (GAB) temperature-independent models. Drying kinetics were quantified under thin-layer laboratory testing and modeled using the Modified Page's equation. Water activity isotherms for non-pelleted biomass were best modeled with the Peleg temperature-independent equation while isotherms for the pelleted biomass were best modeled with the Double Log Polynomial equation. Thin-layer drying results were accurately modeled with the Modified Page's equation. The results of this work indicate that AFEX pretreatment results in drying properties more favorable than or equal to that of raw corn stover, and pellets of superior physical stability in storage.

09 BIOMASS FUELS↗

Assessment of reduction behavior of hematite iron ore pellets in coal fines for application in sponge ironmaking

Studies on isothermal reduction kinetics (with F grade coal) in fired pellets of hematite iron ores, procured from four different mines of Orissa, were carried out in the temperature range of 850-1000C to provide information for the Indian sponge iron plants. The rate of reduction in all the fired iron ore pellets increased markedly with a rise of temperature up to 950C, and thereafter it decreased at 1000C. The rate was more intense in the first 30 minutes. All iron ores exhibited almost complete reduction in their pellets at temperatures of 900 and 950C in 2 hours' heating time duration, and the final product morphologies consisted of prominent cracks. The kinetic model equation 1-(1-a){sup 1/3}=kt was found to fit best to the experimental data, and the values of apparent activation energy were evaluated. Reductions of D. R. Pattnaik and M. G. Mohanty iron ore pellets were characterized by higher activation energies (183 and 150 kJ mol{sup -1}), indicating carbon gasification reaction to be the rate-controlling step. The results established lower values of activation energy (83 and 84 kJ mol{sup -1}) for the reduction of G. M. OMC Ltd. and Sakaruddin iron ore pellets, proposing their overall rates to be controlled by indirect reduction reactions.

01 COAL, LIGNITE, AND PEAT↗

Studies on the reduction kinetics of hematite iron ore pellets with noncoking coals for sponge iron plants

In the present investigation, fired pellets were made by mixing hematite iron ore fines of -100, -16+18, and -8+10 mesh size in different ratios and studies on their reduction kinetics in Lakhanpur, Orient OC-2 and Belpahar coals were carried out at temperatures ranging from 850{sup o}C to 1000{sup o}C with a view toward promoting the massive utilization of fines in ironmaking. The rate of reduction in all the fired iron ore pellets increased markedly with an increase in temperature up to 1000{sup o}C, and it was more intense in the first 30min. The values of activation energy, calculated from integral and differential approaches, for the reduction of fired pellets (prepared from iron ore fines of -100 mesh size) in coals were found to be in the range 131-148 and 130-181 kJ mol{sup -1} (for =0.2 to 0.8), indicating the process is controlled by a carbon gasification reaction. The addition of selected larger size particles in the matrix of -100 mesh size fines up to the extent studied decreased the activation energy and slightly increased the reduction rates of resultant fired pellets. In comparison to coal, the reduction of fired pellets in char was characterized by significantly lower reduction rates and higher activation energy.

01 COAL, LIGNITE, AND PEAT↗

Lightning arrestor connector lead magnesium niobate qualification pellet test procedures.

Enhanced knowledge preservation for DOE DP technical component activities has recently received much attention. As part of this recent knowledge preservation effort, improved documentation of the sample preparation and electrical testing procedures for lead magnesium niobate--lead titanate (PMN/PT) qualification pellets was completed. The qualification pellets are fabricated from the same parent powders used to produce PMN/PT lightning arrestor connector (LAC) granules at HWF&T. In our report, the procedures for fired pellet surface preparation, electrode deposition, electrical testing and data recording are described. The dielectric measurements described in our report are an information only test. Technical reasons for selecting the electrode material, electrode size and geometry are presented. The electrical testing is based on measuring the dielectric constant and dissipation factor of the pellet during cooling from 280 C to 220 C. The most important data are the temperature for which the peak dielectric constant occurs (Curie Point temperature) and the peak dielectric constant magnitude. We determined that the peak dielectric constant for our procedure would be that measured at 1 kHz at the Curie Point. Both the peak dielectric constant and the Curie point parameters provide semi-quantitative information concerning the chemical and microstructural homogeneity of the parent material used for the production of PMN/PT granules for LACs. Finally, we have proposed flag limits for the dielectric data for the pellets. Specifically, if the temperature of the peak dielectric constant falls outside the range of 250 C {+-} 30 C we propose that a flag limit be imposed that will initiate communication between production agency and design agency personnel. If the peak dielectric constant measured falls outside the range 25,000 {+-} 10,000 we also propose that a flag limit be imposed.

36 MATERIALS SCIENCE↗

Effects of Production of Woody Pellets in the Southeastern United States on the Sustainable Development Goals

Wood-based pellets are produced in the southeastern United States (SE US) and shipped to Europe for the generation of heat and power. Effects of pellet production on selected Sustainability Development Goals (SDGs) are evaluated using industry information, available energy consumption data, and published research findings. Challenges associated with identifying relevant SDG goals and targets for this particular bioenergy supply chain and potential deleterious impacts are also discussed. We find that production of woody pellets in the SE US and shipments to displace coal for energy in Europe generate positive effects on affordable and clean energy (SDG 7), decent work and economic growth (SDG 8), industry innovation and infrastructure (SDG 9), responsible consumption and production (SDG 12), and life on land (SDG 15). Primary strengths of the pellet supply chain in the SE US are the provisioning of employment in depressed rural areas and the displacement of fossil fuels. Weaknesses are associated with potential impacts on air, water, and biodiversity that arise if the resource base and harvest activities are improperly managed. The SE US pellet supply chain provides an opportunity for transition to low-carbon industries and innovations while incentivizing better resource management.

09 BIOMASS FUELS↗

Development of laboratory studies on the off-gassing of wood pellets

In the present study three sealed containers (304.8 mm inside diameter and 609.6 mm height) were developed to investigate the concentration of off-gases accumulated in the headspace as well as changes in some of the physical properties of wood pellets during storage. Pellets occupied 75% of the container volume leaving 25% headspace. The outside wall of the steel containers was wrapped with electric heating tapes and fiber glass insulation. The storage studies were carried out at room temperature of about 22 degrees C and at elevated temperatures of 30, 40 and 50 degrees C. The off-gases were collected and analyzed using micro gas chromatography. The accumulations of CO (5000 ppmv) and CO2 (10000 ppmv) were relatively high at room temperature of about 22 degrees C for a storage period of 24 days. These accumulations increased sharply at storage temperatures greather than 30 degrees C. At 50 degrees C, the maximum measured concentration of CO, CO2 and CH4 was about17,000, 70,000 and 3,000 ppmv, respectively. Storage temperature had a significanteffect (PB0.01) on all of the pellet properties, including pellet durability, which dropped by about 20% at the end of 60 days of storage.

09 BIOMASS FUELS↗

Comparative analysis of temperature dependent properties of commercial nuclear fuel pellet and surrogates undergoing cracking: A review

A variety of normal and accident scenarios can generate thermal stresses enough to cause cracking in light water reactor (LWR) fuel. To better understand this behavior, cracking experiments have been carried out to induce thermal gradients in fuel pellets via induction heating and direct resistance heating. In this study, Ceria (CeO 2 ) and yttria stabilized zirconia (YSZ) pellets were chosen as a surrogate fuel material for uranium dioxide (UO 2 ). Induction heating was done using copper coils and molybdenum susceptors which heated the surrogates to a threshold temperature that is sufficiently high for the fuel material to conduct current. Thereafter, direct resistance heating was achieved by passing current through the specimen using a DC power supply to introduce volumetric heating to replicate reactor operating conditions. Simultaneous real-time dual imaging of the ceria pellet surface has been designed using optical and infra-red camera system to capture images of cracks and full-field temperature gradients on pellet. It was observed that YSZ pellets need a much higher voltage-current for volumetric heating and do not exhibit the cracking pattern as ceria and UO 2 , hence YSZ was ruled out for further consideration. Ceria was found to be an appropriate surrogate for UO 2 . Furthermore, the experimental set up and test conditions demand the need to primarily understand the thermo-physical, mechanical and optical properties of UO 2 and the surrogates. Thus, it is essential to have an in-depth knowledge about the various temperature dependent properties of UO 2 and CeO 2 for establishing a comparative analysis between the surrogate and UO 2 for conducting experiments.

36 MATERIALS SCIENCE↗

Isotopic Heterogeneity Imaged in a Uranium Fuel Pellet with Extreme Ultraviolet Laser Ablation and Ionization Time-of-Flight Mass Spectrometry

We use extreme ultraviolet laser ablation and ionization time-of-flight mass spectrometry (EUV TOF) to map uranium isotopic heterogeneity at the nanoscale (=100 nm). Using low-enriched uranium fuel pellets that were made by blending two isotopically distinct feedstocks, we show that EUV TOF can map the 235U/238U content in 100 nm-sized pixels. The two-dimensional (2D) isotope maps reveal U ratio variations in sub-microscale to =1 µm areas of the pellet that had not been fully exposed by microscale or bulk mass spectrometry analyses. Compared to the ratio distribution measured in a homogeneous U reference material, the ratios in the enriched pellet follow a ~3× wider distribution. These results indicate U heterogeneity in the fuel pellet from incomplete blending of the different source materials. EUV TOF results agree well with those obtained on the same enriched pellets by nanoscale secondary ionization mass spectrometry (NanoSIMS), which reveals a comparable U isotope ratio distribution at the same spatial scale. EUV TOF’s ability to assess and map isotopic heterogeneity at the nanoscale makes it a promising tool in fields such as nuclear forensics, geochemistry, and biology that could benefit from uncovering sub-microscale sources of chemical modifications.

Rush, Lydia A.↗

Influence of Pelletization and Moisture Content of Oil Palm Empty Fruit Bunches (EFBs) on Dynamic Gasification Performance

Wet-ground empty fruit bunches (EFBs), dry-ground EFB, and pelletized EFB were gasified in a laboratory-scale updraft fixed-bed reactor at differing temperatures and equivalent ratios (ERs) between 0.19 and 0.78 to evaluate the performance and quality of the syngas under autothermal operating conditions. In addition, the theoretical estimation of the key performance indicator of the ashes on the performance of the gasification process was obtained. The results show that for ERs > 0.4 the autothermal operating condition was achieved for pretreatments with pelletized and dry-ground EFBs, with reactor operating temperatures T > 700 °C. With wet EFB, this condition is achieved at any ER value. The average composition of the syngas from pelletized EFB presented the best average concentrations of the combustible species CO, H2, and CH4 when the ER values were between 0.25 and 0.40. The highest hot and cold thermal efficiency values were obtained for the gasification of EFB pellets with ER values between 0.25 and 0.40. For ground EFB, increases in the ER value led to improvements in hot thermal efficiency. Finally, during the EFB pellet gasification tests, no agglomeration and sintering problems were evidenced in comparison with wet-ground and dry-ground EFBs that showed slag formation, especially at ER < 0.46.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Quantifying Impacts of Biomass Pelletization on Fast Pyrolysis Using a Single-Particle Reactor, X-ray Computed Tomography, and Computational Modeling

The pore structure and density of lignocellulosic feedstocks dictate intraparticle transport phenomena and thereby play an important role in thermochemical conversion processes such as fast pyrolysis for biofuel and biochemical production. Variations in microstructure are inherent from different biomass species and can be introduced by preprocessing techniques such as cutting and pelletization. Morphological changes also occur during conversion and lead to vastly different pore structures and behavior during pyrolysis, which impact required conversion times and product distributions. The current work presents a comprehensive comparison of fast pyrolysis of neat and pelletized pine feedstocks, which includes single-particle experiments, modeling, and 3D imaging by X-ray computed tomography (XCT). The particle-scale model included anisotropic heat and mass transport in a shrinking particle with pyrolysis reactions based on the CRECK mechanism with boundary conditions informed by reactor-scale simulations of the single-particle reactor. The models were validated by measurements of the temperature and mass loss from single-particle pyrolysis experiments of neat and pelletized pine. Quantitative analysis of XCT geometries revealed that pyrolytic conversion yielded chars with increased porosity and permeability compared to the unpyrolyzed materials, along with decreased tortuosity and anisotropy. Pelletization of the pine feedstock resulted in a much denser, less permeable material, which converted slower and produced more residual char after pyrolysis compared to neat pine. The results from particle modeling revealed that accounting for the dynamic and anisotropic heat and mass transport caused by differences in pore structure is critical to achieving agreement with experimental results. Overall, this study highlights the dramatic differences in conversion behavior imparted by pelletization and the importance of capturing microstructural attributes in computational models to guide the design and optimization of pyrolysis processes for specific biomass feedstocks.

09 BIOMASS FUELS↗

A reduced model for edge localized mode control by supersonic molecular beam injection and pellet injection

We develop a diffusive, bistable, tri-unstable cellular automata (CA) model to study the dynamics of H-mode pedestal with edge localized modes (ELMs) and their control by supersonic molecular beam injection (SMBI) and pellet injection (PI). It is shown that the new CA model can reproduce the key features of H-mode pedestals with various types of ELM, including Type-I ELM. SMBI and PI are modeled as additional grain injections into pedestal with varying degrees of injected materials and profiles. It is found that H-mode pedestal responds to SMBI differently depending on the baseline fueling. If the baseline fueling is large enough to allow Type-I ELM, SMBI enhances large transport avalanches caused by ballooning instabilities. These avalanches prevent the total pedestal current from reaching the boundary for peeling instability. On the other hand, if the baseline fueling is low to avoid Type-I ELM, SMBI enhances small scale avalanches, which prevent the pedestal from growing to profiles globally vulnerable to ballooning instabilities. These imply that SMBI can mitigate different types of ELM by converting them to more benign types. From CA modeling of pellet injection, it is shown that Type-I ELM can be triggered by pellet injection with sufficient strength and depth. Scanning the frequency of pellet injection, it is found that a maximum efficiency of pellet pacing is achieved when the injection frequency is approximately ten times the natural frequency of Type-I ELM.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurement and simulation of small cryogenic neon pellet Ne-I 640 nm photon efficiency during ablation in DIII-D plasma

Small (~1 mm) neon pellet fragments are fired into DIII-D H-mode plasmas, and resulting trajectory-averaged photon efficiencies (neutral neon ionization events for every photon emitted) of S/XB ≈ 85 are estimated for Ne-I 640 nm by dividing the estimated initial pellet fragment mass by the measured number of emitted Ne-I photons. The experiments are modeled by running the Lagrangian particle (LP) fluid/magneto-hydrodynamic pellet code to estimate axial ablation plume neon density profiles and temperature profiles at each pellet position. These solutions are then fed into the PrismSPECT collisional-radiative code, which calculates resulting neon charge states and photon emission rates, giving a profile-average of S/XB ≈ 109. The burnthrough plasma minor radius predicted by LP (ρ ≈ 0.63) is reasonably close to the experimental observation ρ ≈ 0.6. Furthermore, the modeling indicates that local S/XB is not constant along the pellet trajectory but tends to increase with increasing ablation rate. Non-equilibrium kinetics are predicted to be very important, while line trapping is predicted to be relatively unimportant (for Ne-I 640 nm S/XB).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Lagrangian particle simulation of hydrogen pellets and SPI into runaway electron beam in ITER

Numerical studies of the ablation of pellets and shattered pellet injection (SPI) fragments into a runaway electron beam in ITER have been performed using a time-dependent pellet ablation code [Samulyak et al., Nucl. Fusion, 61(4), 046007 (2021)]. The code resolves detailed ablation physics near pellet fragments and large-scale expansion of ablated clouds. The study of a single-fragment ablation quantifies the influence of various factors, in particular, the impact ionization by runaway electrons and cross-field transport models, on the dynamics of ablated plasma and its penetration into the runaway beam. Simulations of SPI performed using different numbers of pellet fragments study the formation and evolution of the ablation clouds and their large-scale dynamics in ITER. In conclusion, the penetration depth of the ablation clouds is found to be of the order of 50 cm.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Shattered pellet injection technology design and characterization for disruption mitigation experiments

The technology to form and shoot high-Z cryogenic solid pellets mixed with deuterium using a gas gun that are shattered upon injection into a plasma has been developed at Oak Ridge National Laboratory for mitigating disruptions. This technology has been selected as the basis for the baseline disruption mitigation system on ITER. The development of shattered pellet injection systems has progressed to be able to accelerate large pellets of pure argon and neon with or without including deuterium. Impact studies have been carried out at shallow angles to determine funnel performance in guiding pellets from multiple barrels into a common injection line and across pumping breaks. The characterization of the shattered spray has also progressed with fragment size measurements as a function of pellet speed showing a strong inverse relationship. Results of these studies are reported with implications for applications on existing and future tokamak devices.

Baylor, Larry↗

Control of the hydrogen:deuterium isotope mixture using pellets in JET

Deuterium pellets are injected into initially pure hydrogen H-mode plasma in order to control H:D isotope mixture. The pellets are deposited in outer 20% of minor radius, similar to that expected in ITER creating transiently hollow electron density profiles. The isotope mixture of H:D ~ 45:55% is obtained in the core with pellet fuelling throughput of Φ pel = 0.045 P aux /T e,ped similar to previous pellet fuelling experiments in pure deuterium. Evolution of H:D mix in the core is reproduced using simple model although deuterium transport could be higher at the beginning of the pellet train compared to the flat top phase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Radial electric field and density fluctuations measured by Doppler reflectometry during the post-pellet enhanced confinement phase in W7-X

Radial profiles of density fluctuations and the radial electric field, Er, have been measured using Doppler reflectometry during the post-pellet enhanced confinement phase achieved, under different heating power levels and magnetic configurations, during the 2018 W7-X experimental campaign. A pronounced Er-well is measured with local values as high as -40 kV m -1 in the radial range ρ ~ 0.7–0.8 during the post-pellet enhanced confinement phase. The maximum Er intensity scales with both the plasma density and electron cyclotron heating power level, following a similar trend to the plasma energy content. A good agreement is found when the experimental Er profiles are compared to simulations carried out using the neoclassical codes, the drift kinetic equation solver (DKES) and kinetic orbit-averaging solver for stellarators (KNOSOS). The density fluctuation level decreases from the plasma edge toward the plasma core and the drop is more pronounced in the post-pellet enhanced confinement phase than in reference gas-fuelled plasmas. Besides, in the post-pellet phase, the density fluctuation level is lower in the high iota magnetic configuration than in the standard one. Therefore, to determine whether this difference is related to the differences in the plasma profiles or to the stability properties of the two configurations, gyrokinetic simulations have been carried out using the codes stella and EUTERPE. The simulation results point to the plasma profile evolution after the pellet injection and the stabilization effect of the radial electric field profile as the dominant players in the stabilization of the plasma turbulence.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗