Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PANEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Frequency Response Analysis to Monitor and Identify Changes in the Impedance of a Photovoltaic Panel Measured Online using a Power Optimizer

Photovoltaic (PV) cells are generally modeled as a current source due to photocurrent, p-n junction diodes with parasitic resistance, capacitance, and inductance. This paper proposes online frequency response analysis (FRA) to measure the impedance of a PV panel using an existing panel-level power optimizer in a PV system. The algorithm will actively perturb a small signal into a 300 W rooftop PV panel and compute its small signal impedance. The technology discussed is easy to incorporate, requires no additional hardware, doesn't alter the stability of the system, and is implemented at a steady-state point. The power optimizer initially stabilizes at an operating point and then perturbs the PV current via FRA and computes PV panel impedance. The relative standard deviation test conducted indoors under 300 W/m 2 illumination on a PV panel shows a less than 5% error rate in PV panel impedance magnitude and phase is measured using a power optimizer.

14 SOLAR ENERGY↗
DOE OSTI2023

High-Performance Coal-Based Commercial Facade Panels and Architectural Components (Phase I Final Report)

Semplastics has developed, tested, and documented the viability for commercialization of a new class of composite architectural panel materials that use coal as the primary constituent. This project produced sample panels using these novel materials that comprise 55% coal by mass (71% carbon by mass) and are comparable in dimensions to commercially available materials, while displaying superior mechanical strength, significant weight savings, and better insulating ability at a competitive cost. Phase I moved this coal-based composite materials technology from a Technology Readiness Level (TRL) of 3 to TRL 5. Semplastics’ new coal-based composite materials display an array of high-performance characteristics, including light weight, mechanical durability, temperature stability, and water resistance. These new materials require less energy to produce than comparable commercial products and could be manufactured on existing conventional plastic resin processing equipment in commercial quantities. The coal particles are completely encapsulated in ceramic from a polymer-derived ceramic (PDC) precursor, then bonded together by another inorganic resin. The material can be molded and cured to produce fireproof components such as ceiling panels, facades, and extruded underlayment, blocking, and backer boards, as well as other architectural design components such as moldings. The project included the production of sample panels for proof of concept, testing of the panels to show their improved characteristics, and development of a scale-up strategy to demonstrate the viability of the coal-based panels as a commercial alternative to existing building materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Overview of Solar Panel Recycling for Indigenous Communities

In recent years, Native tribes across the country have embraced solar energy to power their communities. However, in approximately 25-30 years after installation, the solar panels will enter end-of-life (EOL) status, meaning that they will begin to operate less efficiently than upon initial implementation. At this point, tribes can determine the outcome: they can continue to operate the array, or they can dispose of the panels. Recycling is an option that promotes the use of high-value recyclable materials in solar panels in the circular economy. There are several companies across the US that offer recycling of solar panels, but at various costs. It is important that a hazardous waste expert makes an initial assessment of the solar array to identify any solar panels that cannot be recycled. Currently, recycling solar panels is not cost-effective or environmentally sustainable, but significant research into improving the cost and carbon footprint is ongoing.

14 SOLAR ENERGY↗
NASA NTRS1974

A correlation study of finite-element modeling for vibrations of composite material panels

A correlation study has been made to evaluate the effectiveness of finite-element modeling for vibrations of composite material panels. The three types of composite material panels studied were: (1) symmetrically laminated cross-ply panels, (2) unsymmetrically laminated cross-ply panels, and (3) a 1/6-scale sandwich wing model. Correlations of finite-element predictions for frequencies and vibration modes were made with Rayleigh-Ritz analyses and experimental data. For the symmetrically laminated panels, the finite-element representation predicted vibration modes very accurately. For the unsymmetrically laminated panels it was found that predictions using uncoupled finite-element plate bending elements did not give good agreement with experimental data. The constant-chord, swept-wing model was effectively analyzed by finite-element presentations using either sandwich elements or ribs and spars.

Thornton, E. A.↗
NASA NTRS1975

Creep analysis capability for stiffened panel structures

A method of analysis developed for predicting permanent cyclic creep deflections in stiffened panel structures is presented. The resulting computer program (TPSC, for Thermal Protection System Creep) applies either the time hardening or strain hardening theories of creep accumulation, using iterative techniques to determine structural rotations, creep strains, and stresses as a function of time. Deflections are determined by numerical integration of structural rotations along the panel length. The analytical approach was developed for purposes of analyzing thin gage entry vehicle metallic thermal protection system panels subjected to cyclic bending loads at high temperatures. The method is applicable to any panel subjected to bending loads. Predicted panel creep deflections are compared with results from cyclic tests of subsize and full size corrugation and rib stiffened panels. Empirical equations used in the analysis were developed for each material based on correlation with tensile cyclic creep data.

Cramer, B. A.↗
NASA NTRS1976

Vibroacoustic testing of Space Shuttle thermal protection system panels

The modes and acoustic responses of two panels representing Space Shuttle thermal protection panels were investigated. The panels consisted of flat aluminum sheet stiffened longitudinally with hat-section stringers and corrugated supporting panels representing Shuttle ring frame bulkheads. In addition, one panel had 24 tiles of LI900 silica thermal insulation material and a strain isolator pad bonded to the face sheet. Both panels were found to have approximately eight modal frequencies in the 60 to 500 Hz range, where Shuttle acoustic loads are expected to be high. The strain response to a progressive acoustic wave representing a Shuttle spectrum was characterized by the occurrence of larger strains in the direction normal to the stringers than in the direction parallel to the stringers; three modes in the 100 to 400 Hz range contributed significantly to the strain response.

Rucker, C. E.↗
NASA NTRS1976

A higher order panel method for linearized supersonic flow

A higher order panel method using linearly varying source and quadratically varying doublet distributions for computing linearized supersonic flow over arbitrary wings and bodies is described. With tangential mass flux boundary conditions on circular cones at angles of attack, the source panel method gave pressure distributions which are in excellent agreement with exact nonlinear theory. The numerical source panel method was demonstrated to be very stable by randomly panelling an axially symmetric body. For wings with thickness and camber, both the source and doublet panel methods yield excellent agreement with exact linearized solutions. Computational experiments indicate that the use of exact surface paneling in lieu of linearized boundary conditions for wings provides better agreement with higher order theory and with experiment.

Ehlers, F. E.↗
NASA NTRS1977

Development of the technology for the fabrication of reliable laminar from control panels

Materials were assessed and fabrication techniques were developed for use in the manufacture of wing surface materials compatible with the application of both aluminum alloys and nonmetallic composites. The concepts investigated included perforations and slots in the metallic test panels and microporosity and perforations in the composite test panels. Perforations were produced in the metallic test panels by the electron beam process and slots were developed by controlled gaps between the metal sheets. Microporosity was produced in the composite test panels by the resin bleed process, and perforations were produced by the fugitive fiber technique. Each of these concepts was fabricated into test panels, and air flow tests were conducted on the panels.

Meade, L. E.↗
NASA NTRS1978

Noise transmission through flat rectangular panels into a closed cavity

Five panels backed by a closed cavity were studied experimentally and analytically to determine the noise transmission characteristics of the coupled panel-cavity system. The closed cavity was studied both with and without fiber-glass lining to provide either an absorbent or a reverberant acoustic space. The effects on noise reduction of cavity absorption, measurement location within the cavity, panel mass, and panel stiffness were examined. Results indicated that both measurement location and absorption in the cavity have significant effects on the noise reduction. Increasing panel mass improves the noise reduction at almost all frequencies, and increasing panel stiffness improves nose reduction below the fundamental resonance frequency. A simple, one dimensional analytical model was developed which provided good agreement with the experimental results.

Barton, C. K.↗
NASA NTRS1977

Fabrication and evaluation of advanced titanium structural panels for supersonic cruise aircraft

Flightworthy primary structural panels were designed, fabricated, and tested to investigate two advanced fabrication methods for titanium alloys. Skin-stringer panels fabricated using the weldbraze process, and honeycomb-core sandwich panels fabricated using a diffusion bonding process, were designed to replace an existing integrally stiffened shear panel on the upper wing surface of the NASA YF-12 research aircraft. The investigation included ground testing and Mach 3 flight testing of full-scale panels, and laboratory testing of representative structural element specimens. Test results obtained on full-scale panels and structural element specimens indicate that both of the fabrication methods investigated are suitable for primary structural applications on future civil and military supersonic cruise aircraft.

Payne, L.↗
NASA NTRS1978

Fluxless Brazing and Heat Treatment of a Plate-Fin Sandwich Actively Cooled Panel

The processes and techniques used to fabricate plate-fin sandwich actively cooled panels are presented. The materials were 6061 aluminum alloy and brazing sheet having clad brazing alloy. The panels consisted of small scale specimens, fatigue specimens, and a large 0.61 m by 1.22 m test panel. All panels were fluxless brazed in retorts in heated platen presses while exerting external pressure to assure intimate contact of details. Distortion and damage normally associated with that heat treatment were minimized by heat treating without fixtures and solution quenching in an organic polymer solution. The test panel is the largest fluxless brazed and heat treated panel of its configuration known to exist.

Beuyukian, C. S.↗
NASA NTRS1978

Design and fabrication of a radiative actively cooled honeycomb sandwich panel

The mass of a radiative actively cooled panel was compared to the mass of a bare actively cooled panel designed to the same conditions and constraints. The approach was to design and optimize a 0.61 x 6.1 m full scale panel which combines radiative and active cooling to control structural temperatures to levels compatible with use of lightweight materials and to fabricate a 0.61 x 1.22 m panel for performance testing. Results of the design and optimization of the full scale radiative actively cooled structural panel, including radiative concept selection, final configuration details, test panel description, and conclusions are summarized.

Koch, L. C.↗
NASA NTRS1979

A vector-continuous loading concept for aerodynamic panel methods

An approach to the reduction of discretization errors in aerodynamic panel methods is presented. The approach is based on preventing the occurence of induced velocity singularities at panel slope discontinuities by maintaining continuity of the velocity jump vector across the panels. The approach was implemented in a two-dimensional incompressible panel method formulation and evaluated by application to several external and internal flow problems. The method is shown to exhibit a second order accuracy trend and to produce smaller errors with velocity component boundary conditions imposed on the real flow than with equipotential boundary conditions imposed on the imaginary flow behind the panels. For flows around airfoil sections with either sharp or blunt trailing edges, the method gives excellent agreement with results from a well developed finite difference method. The method is well behaved and is insensitive to irregularities in panel size distribution.

Kemp, W. B., Jr.↗
NASA NTRS1979

Aerothermal performance of radiatively and actively cooled panel at Mach 6.6

A flight-weight radiative and actively cooled honeycomb sandwich panel (RACP) was subjected to multiple cycles of both radiant and aerothermal heating. The 0.61 m by 1.22 m test specimen incorporated essential features of a full scale 0.61 m by 6.10 m RACP designed to withstand a heat flux of 136 kW/sq m. The panel consisted of heat shields, a thin layer of high temperature insulation, and an aluminum honeycomb sandwich panel with coolant tubes next to the sandwich skin. A 60/40 mass solution of ethylene glycol/water was used to cool the panel which successfully withstood a total of 3.5 hr of radiant heating and 137 sec exposure to an M = 6.6 test stream. Heat shield temperatures reached 1080 K (1945 deg R), and cooled-panel temperatures reached 382 K (687 deg R) midway between coolant tubes. Simulation of the full scale panel indicated that the full scale RACP would perform as expected. The tests revealed no evidence of coolant leakage or hot gas ingress which would seriously degrade the RACP performance.

Shore, C. P.↗
NASA NTRS1980

Stress analysis and buckling of J-stiffened graphite-epoxy panel

A graphite epoxy shear panel with bonded on J stiffeners was investigated. The panel, loaded to buckling in a picture frame shear test is described. Two finite element models, each of which included the doubler material bonded to the panel skin under the stiffeners and at the panel edges, were used to make a stress analysis of the panel. The shear load distributions in the panel from two commonly used boundary conditions, applied shear load and applied displacement, were compared with the results from one of the finite element models that included the picture frame test fixture.

Davis, R. C.↗
NASA NTRS1979

The structural behavior of a graphite-polymide honeycomb sandwich panel with quasi-isotropic face sheets and an orthotropic core

The results of a series of tests of graphite-polyimide honeycomb sandwich panels are presented. The panels were 1.22 m long, 0.508 m wide, and approximately 13.3 m thick. The face sheets were a T-300/PMR-15 fabric in a quasi-isotropic layup and were 0.279 mm thick. The core was Hexcel HRH 327-3/16 - 4.0 glass reinforced polyimide honeycomb, 12.7 mm thick. Three panels were used in the test: one was cut into smaller pieces for testing as beam, compression, and shear specimens; a second panel was used for plate bending tests; the third panel was used for in-plane stability tests. Presented are the experimental results of four point bending tests, short block compression tests, core transverse shear modulus, three point bending tests, vibration tests, plate bending tests, and panel stability tests. The results of the first three tests are used to predict the results of some of the other tests. The predictions and experimental results are compared, and the agreement is quite good.

Hyer, M. W.↗
NASA NTRS1980

Noise transmission and attenuation by stiffened panels

An analytical study of noise transmission into semi-cylindrical and rectangular acoustic enclosures due to turbulent boundary layer pressure and propeller noise (prop-fan) is presented. The structural noise transmission models include a single panel, discretely stiffened elastic panel and stiffened viscoelastic sandwich panel. Response characteristics of the stiffened panels are evaluated using a transfer matrix procedure. The interior noise field is determined by a Galerkin-like method. The effect on interior noise due to aerodynamic surface flow, cavity back-up pressure, pressurization, mass, stiffness, and damping addition to the structure is investigated. It is shown that stiffened viscoelastic sandwich panels, while providing the same stiffening benefits as an equivalent elastic panel, could significantly reduce vibration levels and subsequently give similar benefits for interior noise control.

Vaicaitis, R.↗
NASA NTRS1981

Design and fabrication of brazed Rene 41 honeycomb sandwich structural panels for advanced space transportation systems

The design and fabrication of two large brazed Rene 41 honeycomb panels, the establishment of a test plan, the design and fabrication of a test fixture to subject the panels to cyclic thermal gradients and mechanical loads equivalent to those imposed on an advanced space transportation vehicle during its boost and entry trajectories are discussed. The panels will be supported at four points, creating three spans. The outer spans are 45.7 cm (18 in.) and the center span 76.2 cm (30 in). Specimen width is 30.5 cm (12 in.). The panels were primarily designed by boost conditions simulated by subjecting the panels to liquid nitrogen, 77K (-320 F) on one side and 455K (360 F) on the other side and by mechanically imposing loads representing vehicle fuel pressure loads. Entry conditions were simulated by radiant heating to 1034K (1400 F). The test program subjected the panels to 500 boost thermal conditions. Results are presented.

Hepler, A. K.↗