SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The best catalyst for OER is Co@V B with η OER of 0.43 V followed by Ni@V C with η OER = 0.47 V. For the ORR process, the best catalyst is Rh@V B with η ORR of 0.40 V followed by Pd@V B and Pd@V C ( η ORR = 0.45 V).
Electrocatalysts encapsulated by nanoscopic overlayers can control the rate of redox reactions at the outer surface of the overlayer or at the buried interface between the overlayer and the active catalyst, leading to complex behavior in the presence of two competing electrochemical reactions. This study investigated oxide encapsulated electrocatalysts (OECs) comprised of iridium (Ir) thin films coated with an ultrathin (2–10 nm thick) silicon oxide (SiO x ) or titanium oxide (TiO x ) overlayer. The performance of SiO x |Ir and TiO x |Ir thin film electrodes towards the oxygen evolution reaction (OER) and Fe(II)/Fe(III) redox reactions were evaluated. An improvement in selectivity towards the OER was observed for all OECs. Overlayer properties, namely ionic and electronic conductivity, were assessed using a combination of electroanalytical methods and molecular dynamics simulations. SiO x and TiO x overlayers were found to be permeable to H 2 O and O 2 such that the OER can occur at the MO x |Ir (M = Ti, Si) buried interface, which was further supported with molecular dynamics simulations of model SiO 2 coatings. In contrast, Fe(II)/Fe(III) redox reactions occur to the same degree with TiO x overlayers having thicknesses less than 4 nm as bare electrocatalyst, while SiO x overlayers inhibit redox reactions at all thicknesses. This observation is attributed to differences in electronic transport between the buried interface and outer overlayer surface, as measured with through-plane conductivity measurements of wetted overlayer materials. These findings reveal the influence of oxide overlayer properties on the activity and selectivity of OECs and suggest opportunities to tune these properties for a wide range of electrochemical reactions.
The renaissance of the energy system through the use of green hydrogen by water electrolysis lies behind the development of abundant, active, and scalable catalysts for the oxygen evolution reaction (OER). A fundumental understanding of the surface properties for these materials is of vital importance in producing viable heterogenous catalysts. In this feature article, we summarize several years of collaborative work on a uniquely faceted NiO(111) nanosheet possessing hexagonal holes with a focus on understanding how the evolution of the catalyst surface and bulk composition effects OER performance. The importance of surface faceting, morphological evolution, and metal combination by different doping strategies are all analyzed and summarized to further improve the material's performance. Furthermore, microwave and supercritical synthesis processes are utilized to understand how varying wet-chemical techniques effect the formation of the NiO(111) nanosheet and activity of the material. We discuss our chosen strategies and the difficulties encountered with optimizing a catalyst surface for the OER.
Earth-abundant oxygen evolution catalysts (OECs) with extended stability in acid can be constructed by embedding active sites within an acid-stable metal-oxide framework. In this paper, we report stable NiPbO x films that are able to perform oxygen evolution reaction (OER) catalysis for extended periods of operation (>20 h) in acidic solutions of pH 2.5; conversely, native NiO x catalyst films dissolve immediately. In situ X-ray absorption spectroscopy and ex situ X-ray photoelectron spectroscopy reveal that PbO 2 is unperturbed after addition of Ni and/or Fe into the lattice, which serves as an acid-stable, conductive framework for embedded OER active centers. The ability to perform OER in acid allows the mechanism of Fe doping on Ni catalysts to be further probed. Catalyst activity with Fe doping of oxidic Ni OEC under acid conditions, as compared to neutral or basic conditions, supports the contention that role of Fe 3+ in enhancing catalytic activity in Ni oxide catalysts arises from its Lewis acid properties.
State-of-the-art OER (oxygen evolution reaction) catalyst syntheses require the use of expensive metals (i.e. Ir) with complex and time-consuming synthetic routes, difficulty in control, and impractical yields. Although some reported catalysts show improved performance (i.e. activity, stability, lowering Ir content with Ru), their synthesis is costly and not viable for scale-up. Here we demonstrate a practical, reliable, and scalable one-pot synthesis method for OER catalysts based on borohydride reduction to quickly yield >100 mg of Ir, Ru, and IrRu nanoparticles (1.6 ± 0.2 nm) with outstanding batch-to-batch consistency. Both mono- and bi-metallic compositions exhibit a metal-core/metal-oxide-shell nanoparticle structure. We further demonstrate the versatility of this method by incorporating earth-abundant yttrium, resulting in a catalyst with improved precious metal utilization for OER. This method serves as a robust platform for generating ultrasmall (<2 nm) multi-metal particles useful for electrocatalysis research.
The use of renewable electricity to prepare materials and fuels from abundant molecules offers a tantalizing opportunity to address concerns over energy and materials sustainability. The oxygen evolution reaction (OER) is integral to nearly all material and fuel electrosyntheses. However, very little is known about the structural evolution of the OER electrocatalyst, especially the amorphous layer that forms from the crystalline structure. Here, we investigate the interfacial transformation of the SrIrO 3 OER electrocatalyst. The SrIrO 3 amorphization is initiated by the lattice oxygen redox, a step that allows Sr 2+ to diffuse and O 2− to reorganize the SrIrO 3 structure. This activation turns SrIrO 3 into a highly disordered Ir octahedral network with Ir square-planar motif. The final Sr y IrO x exhibits a greater degree of disorder than IrO x made from other processing methods. Our results demonstrate that the structural reorganization facilitated by coupled ionic diffusions is essential to the disordered structure of the SrIrO 3 electrocatalyst.
Discovery of high-efficiency water-splitting catalysts is critical for clean hydrogen fuel generation. Quantitative and reliable chemical imaging methods can play a crucial role in providing critical catalyst efficiency information for materials development and screening. Here, we developed a reflection optical imaging method to map the performance of transition metal oxide catalysts for oxygen evolution reaction (OER). The generated high concentration of oxygen in the electrolyte will decrease the refractive index of the solutions near the electrode and change the reflectivity of optical images. We successfully imaged and measured the OER on cobalt oxide, and the localized current density and overpotential distribution maps have been extracted. The oxidation and reduction of cobalt oxide can be imaged with our reflection optical imaging method as well. These maps showed that the catalytic activities are quite different at different locations, and some regions showed much higher activities. This is due to the non-uniformity created by the catalyst synthesis process and demonstrates the importance of using the optical imaging method to map the localized catalytic efficiency. In addition, the NiFe alloy’s OER catalytic activities have been studied as well. The proposed reflection optical imaging method could find many applications in catalyst activity measurement and screening.
The goal of this project was to develop an electrochemical process for depolymerization of biorefinery lignin to industrial chemicals, most notably as replacements in resins. The project team consisted of Ohio University (lead organization), Hexion, Inc. and Lakehead University. There were six distinct project tasks, consisting of Initial Validation, Development of TiO 2 Nanowire-supported Ni-Co Electrocatalysts, Electrochemical Characterization of TiO 2 Nanowire-supported Ni-Co Electrocatalysts, Development of Electrochemical Flow Reactor for Production of Industrial Chemicals and Hydrogen, Product Formulations and Integrated Biorefinery Analysis. The project was divided into two budget periods. After intermediate validation near the end of Budget Period 1, the project was discontinued. This final report is intended to highlight major project objectives and results. Technical metrics were developed between the project team and the DOE validation team during the initial validation period. Critical technical metrics included conversion of lignin to products and product selectivity. Desired products were low molecular weight aromatic compounds in the 150-300 MW range. We targeted this class of compounds because of their potential to replace petroleum derivatives in resin formulations. Electrochemical oxidation of biorefinery lignin can lead to significant lignin depolymerization and conversion, with >40% of the lignin reacted. However, product stream analysis is extremely difficult. We were not able to adequately quantify the concentration of the primary oxidation products, or to determine with any degree of certainty what the product selectivity was. The project team initially proposed analytical techniques such as GC-MS to identify product distributions. However, due to 1) difficulty in extracting products into an organic phase suitable for GC analysis and 2) the wide range of product compounds with similar structures, GC-MS analysis was difficult to perform. The project team did have some success with NMR spectroscopic analysis, but not enough so to adequately identify product selectivity. By UV-vis spectroscopy and statistical analysis, we were able to confirm achieving the technical milestone for lignin conversion, and achieved at least 40% conversion by the electrochemical oxidation technique. However, we were not able to confirm product selectivity using GC-MS analysis, as originally postulated. Despite these difficulties, we were able to incorporate the product stream into a resin, and observed better resin synthesis behavior using the oxidized lignin versus the unoxidized lignin. However, no resin synthesized with oxidized biorefinery lignin met the commercial standards for resin quality. One potential problem with electrochemical oxidation of biomass is the competing oxygen evolution reaction (OER) at the reactor anode. We observed that, especially at higher anode potentials, the OER can consume up to 50% of the energy input to the system, meaning that much of the energy goes toward generation of an essentially worthless product (O 2 ). However, we also observed that the OER can be avoided almost entirely at lower potentials. These uncertainties made assigning a value to the electrochemical reactor product stream difficult. Any product generated electrochemically would have to be valuable enough to offset the additional cost of electricity incurred, including electricity to run the electrochemical reactor and the additional electricity that must be purchased because some of the lignin (which is currently burned in biorefineries to recover energy) is diverted to the electrochemical reactor. It is not clear at this time whether the product stream has sufficient economic value to offset these additional electricity costs. The two most promising areas for this project in terms of demonstrating economic feasibility are product stream analysis and resin synthesis. In particular, product stream analysis has proven to be difficult. With additional time, we would refine analytical techniques to better understand key product stream characteristics, such as aromatic compound content. Evaluating the product streams in resin synthesis would likely provide more information on the economic value of the product stream. If we could determine that value, then we would be able to better evaluate whether the electrochemical conversion approach is feasible. The details of this work are presented in the following final report. The report is organized into individual tasks for clarity, although all tasks were integrated and many occurred simultaneously.
Atomic‑level tailoring of electronic communication between spatially separated metal sites offers a route to accelerate multielectron electrocatalysis. We report Ni-TPTC, Co-TPTC, and heterobimetallic Ni-Co-TPTC supramolecular metal-organic frameworks (SMOFs) for the oxygen evolution reaction (OER) built from a terphenyl‑tetracarboxylate (TPTC) linker. Single-crystal X-ray diffraction of heterobimetallic Ni–Co–TPTC reveals trans-bis-aqua octahedral chains assembled into a π-stacked, hydrogen-bonded lattice and confirms retention of the parent architecture, while powder X-ray diffraction supports an isostructural Co analog. In 1.0 M KOH, Ni-Co-TPTC reaches 20 mA cm −2 at 350 mV and maintains operation at ∼60 mA cm −2 for 45 h with modest decay of the initial current. Time‑dependent ex situ diffraction shows dominant framework reflections with low‑angle shifts consistent with gallery dilation (d‑spacing ∼7.7 → ∼9.2 Å) during early operation, while Co K‑edge X‑ray absorption and microscopy reveal Co‑rich oxide/oxyhydroxide‑like domains at longer times that correlate with decay. X‑ray photoelectron spectroscopy, quantified by the Remote Binding‑Energy Differential, tracks composition‑dependent Ni-Co polarization, and DFT free‑energy analysis suggests that a model Ni-Co environment lowers the Co‑centered potential‑limiting step by ∼0.24 eV relative to the Co‑only framework. Furthermore, these results suggest that framework‑retentive expansion and distal Ni-Co coupling can drive OER activity before gradual deligation and oxide formation mark longer‑time degradation.
Twinning is demonstrated to be an effective way of enhancing efficiencies of metallic catalysts toward electrolytic water splitting. Dendritic Cu possessing dense coherent nanotwin (NT) boundaries (NTCu-5nm) is successfully prepared with an organic-assisted electrodeposition at high pulse current densities. NT boundaries significantly improve electrocatalytic efficiencies and stability of NTCu-5nm over nanocrystalline Cu (NCCu), reducing overpotentials at 10 mA cm -2 for the oxygen evolution reaction (OER) from 378 to 281 mV and from 235 to 88 mV for the hydrogen evolution reaction (HER), with a small chronoamperometric decay of 5% after 100 h continuous overall water splitting at an ultrahigh initial current density of 500 mA cm -2 , largely outperforming the large chronoamperometric decay of 27% for only 1 h operation of the NCCu//NCCu couple. The defective twin boundaries enable formation of active Cu III O 2 - at low overpotentials, thus enhancing OER performance. Furthermore, the synergistic geometric and electronic effects induced by the twin boundaries result in shifts in Gibbs free energies of hydrogen adsorption (ΔG H ) toward the apex of a volcano plot of exchange current density versus ΔG H , leading to the remarkable improvement in HER activity.
Discovery of earth-abundant electrocatalysts to replace iridium for the oxygen evolution reaction (OER) in a proton exchange membrane water electrolyzer (PEMWE) represents a critical step in reducing the cost for green hydrogen production. Here we report a nanofibrous cobalt spinel catalyst codoped with lanthanum (La) and manganese (Mn) prepared from a zeolitic imidazolate framework embedded in electrospun polymer fiber. The catalyst demonstrated a low overpotential of 353 millivolts at 10 milliamperes per square centimeter and a low degradation for OER over 360 hours in acidic electrolyte. A PEMWE containing this catalyst at the anode demonstrated a current density of 2000 milliamperes per square centimeter at 2.47 volts (Nafion 115 membrane) or 4000 milliamperes per square centimeter at 3.00 volts (Nafion 212 membrane) and low degradation in an accelerated stress test.
One of the main bottlenecks that limits the performance of reversible protonic ceramic electrochemical cells (R-PCECs) is the sluggish kinetics of the oxygen reduction and evolution reactions (ORR and OER). Here, the significantly enhanced ORR and OER kinetics and stability of a conventional La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) air electrode by an efficient catalyst coating of barium cobaltite (BCO) is reported. The polarization resistance of a BCO-coated LSCF air electrode at 600 oC is 0.16 Ω cm 2 , about 30% of that of the bare LSCF air electrode under the same conditions. Further, a R-PCEC with the BCO-coated LSCF air electrode shows exceptional performance in both fuel cell (maximum power density of 1.16 W cm -2 at 600 ºC) and electrolysis (current density of 1.80 A cm -2 at 600 ºC at 1.3 V) modes. Finally, the performance enhancement is attributed mainly to the facilitated rate of oxygen surface exchange.
Abstract Clean and efficient energy storage and conversion via sustainable water and nitrogen reactions have attracted substantial attention to address the energy and environmental issues due to the overwhelming use of fossil fuels. These electrochemical reactions are crucial for desirable clean energy technologies, including advanced water electrolyzers, hydrogen fuel cells, and ammonia electrosynthesis and utilization. Their sluggish reaction kinetics lead to inefficient energy conversion. Innovative electrocatalysis, i.e., catalysis at the interface between the electrode and electrolyte to facilitate charge transfer and mass transport, plays a vital role in boosting energy conversion efficiency and providing sufficient performance and durability for these energy technologies. Herein, a comprehensive review on recent progress, achievements, and remaining challenges for these electrocatalysis processes related to water (i.e., oxygen evolution reaction, OER, and oxygen reduction reaction, ORR) and nitrogen (i.e., nitrogen reduction reaction, NRR, for ammonia synthesis and ammonia oxidation reaction, AOR, for energy utilization) is provided. Catalysts, electrolytes, and interfaces between the two within electrodes for these electrocatalysis processes are discussed. The primary emphasis is device performance of OER‐related proton exchange membrane (PEM) electrolyzers, ORR‐related PEM fuel cells, NRR‐driven ammonia electrosynthesis from water and nitrogen, and AOR‐related direct ammonia fuel cells.
Iridium (Ir) is the most active and durable anode catalyst for the oxygen evolution reaction (OER) for proton exchange membrane water electrolyzers (PEMWEs). However, their large-scale applications are hindered by high costs and scarcity of Ir. Lowering Ir loadings below 1.0 mgcm -2 causes significantly reduced PEMWE performance and durability. Therefore, developing efficient low Ir-based catalysts is critical to widely commercializing PEMWEs. Herein, an approach is presented for designing porous Ir metal aerogel (MA) catalysts via chemically dealloying IrCu alloys. In this study, the unique hierarchical pore structures and multiple channels of the Ir MA catalyst significantly increase electrochemical surface area (ECSA) and enhance OER activity compared to conventional Ir black catalysts, providing an effective solution to design low-Ir catalysts with improved Ir utilization and enhanced stability. An optimized membrane electrode assembly (MEA) with an Ir loading of 0.5 mg Ir cm -2 generated 2.0 A cm -2 at 1.79 V, higher than the Ir black at a loading of 2.0 mg Ir cm -2 (1.63 A cm -2 ). The low-Ir MEA demonstrated an acceptable decay rate of ≈40 µV h -1 during durability tests at 0.5 (>1200 h) and 2.0 A cm -2 (400 h), outperforming the commercial Ir-based MEA (175 µV h -1 at 2.0 mg Ir cm -2 ).
Iridium-based catalysts remain the most reliable option for the oxygen evolution reaction (OER) in proton exchange membrane water electrolyzers (PEMWEs). However, their high cost and limited performance represent critical barriers to the commercialization of this green hydrogen production technology. Herein, we report the creation of a metallic Ir nanowire network (IrNWN), which exhibits superior OER performance through its in-situ transition into an oxide structure with high intrinsic activity. At a low loading of 0.25 mgIr/cm2 in PEMWEs, IrNWN achieved a current density of 3.13 A/cm2 at a cell voltage of 1.8 V, outperforming the commercial Ir-based catalyst and surpassing the Department of Energy (DOE) 2026 technical target. Moreover, the high activity of IrNWN was maintained for 900 hours in a durability test at 2 A/cm2, showing a low degradation rate of 0.042 mV/hour. Structural analysis of the electrochemically oxidized IrNWN revealed the presence of mixed Ir oxidation states and a high density of surface terminal oxygen groups (μ1-O), which contributed to a reduced energy barrier for the rate-determining O-O coupling step.
The development of a nonprecious, stable, and highly effective electrocatalyst for decomposition of water into oxygen and hydrogen is vitally important for sustainable energy conversion, but it still remains challenging to replace the noble metal electrocatalysts with more economically viable alternatives. Here, in this paper, a polyaniline (PANI) decorated hierarchical nickel cobalt thiospinel (NiCo 2 S 4 ) hybrid catalyst (NCS-P) has been developed that shows enhanced dual catalytic activity for both the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER) compared to pristine NiCo 2 S 4 (NCS). Benefiting from the conductive PANI coating, the hierarchical NCS-P nanostructure exhibits outstanding electrocatalytic activity in alkaline solution with low overpotentials of 273 ± 3 and 77 ± 4 mV at 10 mA cm -2 and low Tafel slopes of 42.2 and 68.5 mV dec -1 for OER and HER, respectively, which are better than those of the benchmark noble-metal-based RuO 2 and Pt/C.
Designing electrocatalysts that excel in hydrogen and oxygen electrochemistry is crucial for sustainable hydrogen generation through electrochemical water splitting. This study presents a novel tricomponent catalyst composed of an alginate hydrogel (AL) infused with single-walled carbon nanotubes (CNTs) and copper oxide (CuO) nanoparticles. The catalyst exhibits benchmark-close bifunctional activity toward hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) under alkaline conditions. The aerophobic nature of the AL-gel facilitates superior bubble release from the electrode, while the inclusion of CNTs mitigates charge transfer resistance. Moreover, heterojunctions of CuO and CNTs create unique interfacial active sites, culminating in high electrocatalytic water-splitting activity. The structural rigidity of the composite permits its use as self-standing electrodes (SSE) without using substrates or binders, enabling a direct evaluation of its activity. The composite electrode demonstrates exceptional electrocatalytic HER activity in an alkaline solution, with onset potentials of 93 mV and moderate OER activity with an onset of 155 mV. Furthermore, a water electrolysis cell featuring the bifunctional SSE exhibits an open circuit voltage of 1.85 V at 100 mA.cm −2 , and only 8% efficiency loss after 100 h marking this a significant stride in developing self-standing nonprecious electrocatalysts with impressive catalytic performance.
The ability to synthesize compositionally complex nanostructures rapidly is a key to high-throughput functional materials discovery. In addition to being time-consuming, a majority of conventional materials synthesis processes closely follow thermodynamics equilibria, which limit the discovery of new classes of metastable phases such as high entropy oxides (HEO). Herein, a photonic flash synthesis of HEO nanoparticles at timescales of milliseconds is demonstrated. By leveraging the abrupt heating and cooling cycles induced by a high-power-density xenon pulsed light, mixed transition metal salt precursors undergo rapid chemical transformations. Hence, nanoparticles form within milliseconds with a strong affinity to bind to the carbon substrate. Oxygen evolution reaction (OER) activity measurements of the synthesized nanoparticles demonstrate two orders of magnitude prolonged stability at high current densities, without noticeable decay in performance, compared to commercial IrO 2 catalyst. This superior catalytic activity originates from the synergistic effect of different alloying elements mixed at a high entropic state. It is found that Cr addition influences surface activity the most by promoting higher oxidation states, favoring optimal interaction with OER intermediates. The proposed high-throughput method opens new pathways toward developing next-generation functional materials for various electronics, sensing, and environmental applications, in addition to renewable energy conversion.