SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The design, analysis, fabrication and testing of a Kevlar-49/HBRF-55A filament wound chamber is reported. The chamber was fabricated and successfully tested to 80% of the design burst pressure. Results of the data reduction and analysis from the hydrotest indicate that the chamber design and fabrication techniques used for the chamber were adequate and the chamber should perform adequately in a static test.
This paper presents the structural design of a bolted joint with a static face seal which can be used to join Space Shuttle Solid Rocket Motor (SRM) case segments. Results from numerous finite element parametric studies indicate that the bolted joint meets the design requirement of preventing joint opening at the O-ring locations during SRM pressurization. A final design recommended for further development has the following parameters: 180 1-inch-diameter studs, stud center line offset of .5 inches radially inward from the shell wall center line, flange thickness of 0.75 inches, bearing plate thickness of 0.25 inches, studs prestressed to 70 percent of ultimate load, and the intermediate alcove. The design has a mass penalty of 1096 lbm, which is 164 lbm greater than the currently proposed capture tang redesign.
A walking robot was designed, analyzed, and tested as an intelligent, mobile, and a terrain adaptive system. The robot's design was an application of existing technologies. The design of the six legs modified and combines well understood mechanisms and was optimized for performance, flexibility, and simplicity. The body design incorporated two tripods for walking stability and ease of turning. The electrical hardware design used modularity and distributed processing to drive the motors. The software design used feedback to coordinate the system and simple keystrokes to give commands. The walking machine can be easily adapted to hostile environments such as high radiation zones and alien terrain. The primary goal of the leg design was to create a leg capable of supporting a robot's body and electrical hardware while walking or performing desired tasks, namely those required for planetary exploration. The leg designers intent was to study the maximum amount of flexibility and maneuverability achievable by the simplest and lightest leg design. The main constraints for the leg design were leg kinematics, ease of assembly, degrees of freedom, number of motors, overall size, and weight.
To provide a suitable electromagnetic torque summing approach to flight control system redundancy, a four channel motor capable of sustaining full performance after any two credible failures was designed, fabricated, and tested. The design consists of a single samarium cobalt permanent magnet rotor with four separate three phase windings arrayed in individual stator quadrants around the periphery. Trade studies established the sensitivities of weight and performance to such parameters as design speed, winding pattern, number of poles, magnet configuration, and strength. The motor electromagnetically sums the torque of the individual channels on a single rotor and eliminate complex mechanical gearing arrangements.
A 71 cm diameter 74 cm length boron/epoxy composite rocket motor chamber was designed based on the geometric configuration of the JPL Applications Technology Satellite titanium alloy apogee motor chamber. Because analyses showed large stress concentrations in the domes, the configuration was modified using the same basic constraints for openings and attachments. The rocket motor chamber was then fabricated by filament winding with boron/epoxy tape and hydrostatically tested to failure at 264 N/sq cm, 57.2 N/sq cm above the design value. Two more rocket motor chambers were fabricated with the same basic constraints, but shortened to 57.6 cm for a smaller propellant load. The first of these short chambers failed in proof because of filament winding fabrication difficulties. The second chamber was successfully fabricated and passed the hydrostatic proof test.
Guidelines and practices for design of solid rocket motor cases
During the 2019 summer term, the author worked with a group of four interns to complete the preliminary design of a 2nd stage solid rocket motor for Up Aerospace’s Spyder Launch Vehicle. The Spyder vehicle is a four stage, solid fuel rocket designed as part of collaboration between NASA and Up Aerospace to develop a vehicle capable of delivering a 10 kg, 6U CubeSat into a 350 km, circular, low Earth orbit. As part of the agreement, NASA is tasked with designing high performance 2nd, 3rd, and 4th stages while Up Aerospace will provide the 1st stage, derived from the first stage of the company’s sub-orbital Spaceloft XL vehicle. Previous intern teams have designed the 3rd and 4th stages, which left the preliminary design of the 2nd stage motor to be completed this summer. The purpose of this report is to highlight a trade study which the author conducted to determine the nozzle geometry which would most benefit the performance of the 2nd stage motor. In this study, various nozzle parameters such as throat radius (RSI), expansion ratio, mass and their effects on the Isp and Delta V of the 2nd Stage were investigated. From this study, a nozzle geometry providing the necessary performance was chosen and implemented as part of the preliminary design of the 2nd stage motor. To mature the 2nd stage motor design, a trade space was needed to determine the nozzle configuration which would most benefit the performance of the 2nd stage. The trade space established did not only evaluate different expansion ratios for the same throat radius, but also investigated the possible performance gained from decreasing the throat radius to increase the expansion ratio and Isp capable of being delivered by the nozzle. Decreasing the throat radius would cause the chamber pressure to increase, consequently increasing the case and insulation mass required to safely operate a motor at higher pressures. To account for this factor, accurate estimates of inert mass first needed to be established. After doing so, the effects of varying nozzle expansion ratios, exit half angles, and subsequently length and mass were evaluated against motor and nozzle performance factors such as delta V and Isp. For this study, four throat radii ranging from 1.75” to 2.375” and consequently four different chamber pressures ranging 550 psia to 1200 psia were investigated. BACKGROUND To launch into Low Earth Orbit, a payload needs to be accelerated to the orbital velocity necessary to keep it from falling back to Earth. The change in velocity required between launch and orbital insertion is known as Delta V. The Delta V which a rocket or stage can deliver can be calculated using the Ideal Rocket equation, 𝛥𝑉=−𝑔0∗𝐼𝑠𝑝∗ln(𝑀𝑓𝑀𝑖) (3) Where 𝑔0 is the acceleration due to gravity at the earth’s surface, 𝐼𝑠𝑝 is the specific impulse of the rocket, 𝑀𝑖 is the initial mass of the rocket, and 𝑀𝑓 is the final mass of the rocket after burnout. From preliminary calculations beyond the scope of this paper, it was determined that 30500 ft/s of delta V would be required for a payload to be inserted into a 350 km circular orbit around the Earth. Using the known masses and Isp values of the 1st, 3rd, and 4th stages and equation 3, the delta V of each stage was calculated. The delta V required by the 2nd stage could then be found by taking the difference between the total delta V required and the delta V of the 1st, 3rd, and 4th stages. From this, the required delta V of the 2nd Stage was calculated to be 7340 ft/s. Specific impulse is an efficiency factor of the nozzle which defines the impulse delivered by the motor per unit of propellant weight. The main variables of a nozzle’s specific impulse investigated in this trade were exit cone half angle, throat radius, and expansion ratio which is affected by the throat radius. The expansion ratio, ε, of a nozzle is defined as the ratio between the nozzle exit area and throat area, and can be calculated using the equation, ε=𝑅𝑒𝑥𝑖𝑡2𝑅𝑠𝑖2 (2) Where 𝑅𝑒𝑥𝑖𝑡 is the radius of the nozzle’s exit and 𝑅𝑠𝑖 is the radius of the nozzle’s throat. A larger expansion ratio and smaller exit half angle will increase the Isp of a nozzle by allowing the gas to expand more and by allowing more of the exhaust gas to produce thrust in the direction of the motor’s central axis. A cross section view of the 2nd Stage motor with the major components annotated is provided in figure 1.
With the growing concerns of global warming, the need for pollution-free vehicles is ever increasing. Pollution-free flight is one of NASA's goals for the 21" Century. , One method of approaching that goal is hydrogen-fueled aircraft that use fuel cells or turbo- generators to develop electric power that can drive electric motors that turn the aircraft's propulsive fans or propellers. Hydrogen fuel would likely be carried as a liquid, stored in tanks at its boiling point of 20.5 K (-422.5 F). Conventional electric motors, however, are far too heavy (for a given horsepower) to use on aircraft. Fortunately the liquid hydrogen fuel can provide essentially free refrigeration that can be used to cool the windings of motors before the hydrogen is used for fuel. Either High Temperature Superconductors (HTS) or high purity metals such as copper or aluminum may be used in the motor windings. Superconductors have essentially zero electrical resistance to steady current. The electrical resistance of high purity aluminum or copper near liquid hydrogen temperature can be l/lOO* or less of the room temperature resistance. These conductors could provide higher motor efficiency than normal room-temperature motors achieve. But much more importantly, these conductors can carry ten to a hundred times more current than copper conductors do in normal motors operating at room temperature. This is a consequence of the low electrical resistance and of good heat transfer coefficients in boiling LH2. Thus the conductors can produce higher magnetic field strengths and consequently higher motor torque and power. Designs, analysis and actual cryogenic motor tests show that such cryogenic motors could produce three or more times as much power per unit weight as turbine engines can, whereas conventional motors produce only 1/5 as much power per weight as turbine engines. This summer work has been done with Litz wire to maximize the current density. The current is limited by the amount of heat it generates. By increasing the heat transfer out of the wire, the wires can carry a larger current and therefore produce more force. This was done by increasing the surface area of the wire to allow more coolant to flow over it. Litz wire was used because it can carry high frequency current. It also can be deformed into configurations that would increase the surface area. The best configuration was determined by heat transfer and force plots that were generated using Maxwell 2D. Future work will be done by testing and measuring the thrust force produced by the wires in a magnetic field.
Design, development, and manufacture of inertia reaction wheel with brushless direct current motor drive
A study was conducted to develop a solid-propellant rocket igniter system that would build up thrust at a controlled rate of less than 0.2 G/sec. The system consisted of a long burning, regressive burning, controlled flow igniter and an inhibited progressive burning surface in the main rocket motor. The igniter performed the dual role of igniting, under vacuum backpressure and low L* (motor free volume/nozzle throat area ratio) conditions, the nonrestricted portion of the propellant and providing the mass addition necessary to sustain combustion until the propellant burning area had increased sufficiently to provide a stable motor-chamber pressure. Two series of tests were conducted with existing small test motor hardware to: (1) demonstrate the feasibility of the concept, (2) determine the important parameters governing the system, and (3) obtain design guidelines for future scaled-up motor tests. A quasi-steady-state mass balance for the ignition system was written and programmed for use as a motor design tool.
An overview will be provided on NASA GRC activities in additive manufacturing (AM) technology development for advanced high performance, propulsion component designs in electric motors and turbine engine systems in future electrified aircraft. AM offers significant benefits over conventional manufacturing to fabricate components that are more compact, lighter weight, geometrically complex, innovatively cooled, integrated, multi-material, and multifunctional. For turbine engine applications, silicon carbide (SiC) based composites are being pursued using binder jetting. For electric motor applications, additive processes are being applied toward optimized component designs to include the housing, rotor, and stators with 3-D printing and wire imbedded coils and with direct printed 3-phase coils. The will be an emphasis on capabilities in additive manufacturing.
The analysis followed five selected motors through initial design, development, test, qualification, manufacture, and final flight reports. An audit was conducted at the manufacturing plants to complement the literature search with firsthand observations of the current philosophies and practices that affect reliability of the motors. A second literature search emphasized acquisition of spacecraft and satellite data bearing on solid motor reliability. It was concluded that present practices at the plants yield highly reliable flight hardware. Reliability can be further improved by new developments of aft-end bonding and initiator/igniter nondestructive test methods, a safe/arm device, and an insulation formulation. Minimum diagnostic instrumentation is recommended for all motor flights. Surplus motors should be used in margin testing. Criteria should be established for pressure and zone curing. The motor contractor should be represented at launch. New design analyses should be made of stretched motors and spacecraft/motor pairs.
A general purpose six-axis robotic manipulator controller was designed and implemented to serve as a research tool for the investigation of the practical and theoretical aspects of various control strategies in robotics. A 80286-based Intel System 310 running the Xenix operating servo software as well as the higher level software (e.g., kinematics and path planning) were employed. A Multibus compatible interface board was designed and constructed to handle I/O signals from the robot manipulator's joint motors. From the design point of view, the universal controller is capable of driving robot manipulators equipped with D.C. joint motors and position optical encoders. To test its functionality, the controller is connected to the joint motor D.C. power amplifier of a PUMA 560 arm bypassing completely the manufacturer-supplied Unimation controller. A controller algorithm consisting of local PD control laws was written and installed into the Xenix operating system. Additional software drivers were implemented to allow application programs access to the interface board. All software was written in the C language.
This project is development effort of a first stage solid motor based on a two-stage solid motor Mars Ascent Vehicle (MAV) design for the robotic Mars Sample Return (MSR) mission (fig. 1). The MSR MAV has been studied for decades and multiple concepts have been shown to meet the mission objectives as posed.1 However, there remains significant uncertainty with the MAV requirements. The sample container and sample cache itself is immature. Additionally, MAV-specific requirements ranging from full three-axis controlled and strict communication requirements to minimal capability concepts are still under consideration. Given the maturity of the overall mission requirements, the MAV has been limited to a large number of parametric analyses and paper studies. Recently, a Jet Propulsion Laboratory study highlighted the flexibility of a two-stage solid motor concept. The MAV itself is driven by the constraints of the Entry, Decent, and Landing (EDL) system. Within the EDL constraints, there is a range of MAV options ranging in complexity from simple spun upper stage options to higher capability three-axis controlled solutions. There are also options to trade the ratio of mission (Delta)V between the first and second stage. Finally, sensitivity studies also indicated that solid motors with a high percentage of off-load flexability only had minor impact on the total system mass over a single point design optimized motor. This flexibility in the first stage motor has allowed NASA to mature the design of the motor beyond parametric analyses and start to address known design challenges of the motor.
This paper presents an extreme environment capable Distributed Motor Controller (DMC) module suitable for operation with a distributed architecture of future spacecraft systems. This motor controller is designed to be a bus-based electronics module capable of operating a single Brushless DC motor in extreme space environments: temperature (-120 C to +85 C required, -180 C to +100 C stretch goal); radiation (>;20K required, >;100KRad stretch goal); >;360 cycles of operation. Achieving this objective will result in a scalable modular configuration for motor control with enhanced reliability that will greatly lower cost during the design, fabrication and ATLO phases of future missions. Within the heart of the DMC lies a pair of cold-capable Application Specific Integrated Circuits (ASICs) and a Field Programmable Gate Array (FPGA) that enable its miniaturization and operation in extreme environments. The ASICs are fabricated in the IBM 0.5 micron Silicon Germanium (SiGe) BiCMOS process and are comprised of Analog circuitry to provide telemetry information, sensor interface, and health and status of DMC. The FPGA contains logic to provide motor control, status monitoring and spacecraft interface. The testing and characterization of these ASICs have yielded excellent functionality in cold temperatures (-135 C). The DMC module has demonstrated successful operation of a motor at temperature.
The complex space shuttle design was comprised of four components: the external tank, two solid rocket boosters (SRB), and the orbiter vehicle. Six orbiters were used during the life of the program. In order of introduction into the fleet, they were: Enterprise (a test vehicle), Columbia, Challenger, Discovery, Atlantis and Endeavour. The space shuttle had the unique ability to launch into orbit, perform on-orbit tasks, return to earth and land on a runway. It was an orbiting laboratory, International Space Station crew delivery and supply replenisher, satellite launcher and payload delivery vehicle, all in one. Except for the external tank, all components of the space shuttle were designed to be reusable for many flights. ATK s reusable solid rocket motors (RSRM) were designed to be flown, recovered, and the metal components reused 20 times. Following each space shuttle launch, the SRBs would parachute into the ocean and be recovered by the Liberty Star and Freedom Star recovery ships. The recovered boosters would then be received at the Cape Canaveral Air Force Station Hangar AF facility for disassembly and engineering post-flight evaluation. At Hangar AF, the RSRM field joints were demated and the segments prepared to be returned to Utah by railcar. The segments were then shipped to ATK s facilities in Clearfield for additional evaluation prior to washout, disassembly and refurbishment. Later the refurbished metal components would be transported to ATK s Promontory facilities to begin a new cycle. ATK s RSRMs were manufactured in Promontory, Utah. During the Space Shuttle Program, ATK supported NASA s Marshall Space Flight Center whose responsibility was for all propulsion elements on the program, including the main engines and solid rocket motors. On launch day for the space shuttle, ATK s Launch Site Operations employees at Kennedy Space Center (KSC) provided lead engineering support for ground operations and NASA s chief engineer. It was ATK s responsibility to have a representative in Firing Room 2 at KSC in case of potential motor problems. However, the last time ATK was responsible for a space shuttle launch slip was 1989. During launch, engineers were also stationed in Promontory on teleconference with counterparts at KSC in the event their support was required.
Performance tests and torque-speed graphs for motor ring-counter inverter system
Explore the source record for details and available documents.