Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructures, and Modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The microstructure effects on irradiation response of ferritic – martensitic steels

Microstructural optimization to achieve greater mechanical strength has been one of the focuses in ferritic–martensitic steels development. However, these optimized microstructures’ effects on the radiation response are not well known. In this work, two ferritic–martensitic steels (9Cr-NbMo and 9Cr-Ta) underwent neutron irradiation in the High Flux Isotope Reactor, and their room-temperature post-irradiation tensile properties and microstructure evolutions were investigated and compared. These two steels exhibit similar pre-irradiation tensile behavior, and their yield strengths are higher than that of other ferritic–martensitic steels by about 200–250 MPa. Microstructural characterization on pre-irradiated materials reveals a smaller grain size in 9Cr-Ta (2.8 ± 0.3 μm in 9Cr-Ta versus 4.3 ± 0.5 μm in 9Cr-NbMo) but higher dislocation density and precipitate density in 9Cr-NbMo. As is common for ferritic–martensitic steels at low irradiation temperatures (less than about 0.45T m ), irradiation-induced hardening at 400 °C was observed for both alloys. Irradiation at 490 °C causes the two alloys to exhibit different tensile behavior: 9Cr-Ta softens by 208 MPa in yield stress, whereas 9Cr-NbMo maintains strength. Additionally, microstructural characterizations were performed, including precipitate growth, dislocation, and defect formation. Using the barrier hardening model for microstructure–property correlation, the softening in irradiated 9Cr-Ta is primarily attributed to the significant dislocation recovery, while the strength lost from the slight dislocation recovery in 9Cr-NbMo was compensated by the additional strength from the irradiation-induced cavities. The microstructure effect (primarily precipitate, dislocation and boundary) on the radiation response is discussed herein.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Guiding the Design of Heterogeneous Electrode Microstructures for Li-Ion Batteries: Microscopic Imaging, Predictive Modeling, and Machine Learning

Electrochemical and mechanical properties of lithium-ion battery materials are heavily dependent on their 3D microstructure characteristics. A quantitative understanding of the role played by stochastic microstructures is critical for the prediction of material properties and for guiding synthesis processes. Furthermore, tailoring microstructure morphology is also a viable way of achieving optimal electrochemical and mechanical performances of lithium-ion cells. To facilitate the establishment of microstructure-resolved modeling and design methods, a review covering spatially and temporally resolved imaging of microstructure and electrochemical phenomena, microstructure statistical characterization and stochastic reconstruction, microstructure-resolved modeling for property prediction, and machine learning for microstructure design is presented here. The perspectives on the unresolved challenges and opportunities in applying experimental data, modeling, and machine learning to improve the understanding of materials and identify paths toward enhanced performance of lithium-ion cells are presented.

25 ENERGY STORAGE↗
DOE OSTI2026

Microstructure Validation of Graph Theory Model-Derived Cooling Rates in the Wire Arc Additive Manufacturing of ER70S-6 Steel

Wire arc additive manufacturing (WAAM) enables high-rate fabrication of large metallic components, but spatial variations in thermal history can lead to microstructural heterogeneity that requires efficient process models to evaluate. This study evaluates whether cooling rates extracted from a graph theory model (GTM)-based thermal simulation are consistent with the microstructural evolution observed in an ER70S-6 WAAM wall. Thermal histories from the model were analyzed at selected build heights, and cooling rates were extracted from the final thermal excursion through the austenite phase field. Microstructures at corresponding locations were characterized using electron backscatter diffraction (EBSD) to quantify grain size distributions, and pearlite interlamellar spacing was used as an additional indicator of cooling behavior. The modeled cooling rates were highest near the substrate and generally decreased with build height, consistent with the observed reduction in the fine grain fraction and the progressive shift in the grain size distribution as build height increased. Pearlite spacing trends also supported the modeled cooling rate variation. These results indicate that GTM-derived thermal histories can be post-processed into metallurgically meaningful cooling rate estimates for WAAM steel builds and linked to dataset specific empirical grain size distribution relationships for process–thermal history–microstructure assessment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Simulation and analysis of small angle scattering (SAS) patterns of Ni-based superalloy microstructures generated by a phase-field model

This paper investigates the relationship between microstructural features and small-angle scattering (SAS) patterns in Ni-based superalloys using a combined phase-field and SAS simulation approach coupled with microstructure analyses. The simulated SAS patterns accurately capture key experimental observations previously reported in the literature, including the time-dependent transition from circular to square-shaped precipitates and the development of anisotropic SAS patterns. Importantly, our analysis reveals the correlations between characteristic length scales extracted from SAS profiles and microstructural descriptors, such as precipitate size and inter-precipitate distance. These findings provide a comprehensive understanding of the link between SAS profiles and microstructure evolution in Ni-based superalloys, offering valuable insights for materials characterization and design.

Microstructure↗
DOE OSTI2021

GeoMicro3D: A novel numerical model for simulating the reaction process and microstructure formation of alkali-activated slag

Highlights: • The GeoMicro3D model was innovatively developed for simulating the reaction process and microstructure formation of AAS. • In GeoMicro3D, the dissolution of slag and reactions of aqueous ions are fundamentally described in the local lattice cell. • A novel approach is proposed to speed up the nucleation simulations. • GeoMicro3D was implemented and verified with the relevant experimental data and thermodynamic calculation results. For the first time, this study developed a novel model, named GeoMicro3D, to simulate the reaction process and microstructure formation of alkali-activated slag. The GeoMicro3D model consists of four modules that are designed to simulate, respectively: (i) the initial spatial distribution of real-shape slag particles in alkaline activator, (ii) the dissolution of slag and diffusion of ions via the transition state theory and lattice Boltzmann method, respectively, (iii) the spatial distribution of reaction products using a nucleation probability theory, and (iv) the chemical reactions with thermodynamic modelling. Afterwards the GeoMicro3D model was implemented and verified. The simulation results were discussed and compared with the relevant experimental data and thermodynamic calculation results using GEMS. A good agreement was found in the comparisons, showing the strong simulation capability of GeoMicro3D.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Propagation of Input Uncertainties in Numerical Simulations of Laser Powder Bed Fusion

Laser powder bed fusion has the potential of redefining state-of-the-art processing and production methods, but defect formation and inconsistent build quality have limited the implementation of this process. Numerical models are widely used to study this process and predict the formation of these defects. Presently, the uncertainties of model input parameters and thermophysical properties used by these numerical simulations have not been investigated. In the present study, the uncertainty in these input parameters and material properties are quantified for laser powder bed fusion, with and without a simulated powder bed, to determine their influence on the predictive accuracy of an experimentally validated numerical model. Accounting for all possible sources of uncertainty quickly becomes computationally expensive on account of the curse of dimensionality. Uncertainty in laser absorption, solid, and liquid specific heat of the metal were found to have the largest effect on model prediction reliability with or without the use of a powder bed. Results also illustrate that accounting for these three uncertain parameters still captures the majority of model prediction uncertainty. Furthermore, the methodology of this study may be used to understand the uncertainty in as-built microstructure through propagation to microstructure prediction models, or applied under processing conditions where high Péclet numbers are observed and the thermal convection and fluid flow within the molten pool are substantial.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1996

Thermoplastic Ribbon-Ply Bonding Model

The aim of the present work was to identify key variables in rapid weldbonding of thermoplastic tow (ribbon) and their relationship to matrix polymer properties and to ribbon microstructure. Theoretical models for viscosity, establishment of ply-ply contact, instantaneous (Velcro) bonding, molecular interdiffusion (healing), void growth suppression, and gap filling were reviewed and synthesized. Consideration of the theoretical bonding mechanisms and length scales and of the experimental weld/peel data allow the prediction of such quantities as the time and pressure required to achieve good contact between a ribbon and a flat substrate, the time dependence of bond strength, pressures needed to prevent void growth from dissolved moisture and conditions for filling gaps and smoothing overlaps.

Hinkley, Jeffrey A.↗
DOE OSTI2023

Modeling laser interactions with aluminum and tantalum targets using a hybrid atomistic-continuum model

A hybrid atomistic-continuum method can model the microstructure evolution of metals subjected to laser irradiation. This method combines classical molecular dynamics (MD) simulations with the two-temperature model (TTM) to account for the laser energy absorption and heat diffusion behavior. Accurate prediction of the temperature evolution in the combined MD-TTM method requires reliable accuracy in electron heat capacity, electron thermal conductivity, and electron–phonon coupling factor across the temperatures generated. This study uses the electronic density of states (DOS) obtained from first-principle calculations. The calculated electron temperature-dependent parameters are used in MD-TTM simulations to study the laser metal interactions in FCC and BCC metals and the phenomenon of laser shock loading and melting. This study uses FCC Al and BCC Ta as model systems to demonstrate this capability. When subjected to short pulsed laser shocks, the dynamic failure behavior predicted using temperature-dependent parameters is compared with the experimentally reported single-crystal and nanocrystalline Al and Ta systems. The MD-TTM simulations also investigate laser ablation and melting behavior of Ta to compare with the ablation threshold reported experimentally. In conclusion, this manuscript demonstrates that integrating the temperature-dependent parameters into MD-TTM simulations leads to the accurate modeling of the laser–metal interaction and allows the prediction of the kinetics of the solid–liquid interface.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Extreme shear-deformation-induced modification of defect structures and hierarchical microstructure in an Al–Si alloy

Abstract Extreme shear deformation is used for several material processing methods and is unavoidable in many engineering applications in which two surfaces are in relative motion against each other while in physical contact. The mechanistic understanding of the microstructural evolution of multi-phase metallic alloys under extreme shear deformation is still in its infancy. Here, we highlight the influence of shear deformation on the microstructural hierarchy and mechanical properties of a binary as-cast Al-4 at.% Si alloy. Shear-deformation-induced grain refinement, multiscale fragmentation of the eutectic Si-lamellae, and metastable solute saturated phases with distinctive defect structures led to a two-fold increase in the flow stresses determined by micropillar compression testing. These results highlight that shear deformation can achieve non-equilibrium microstructures with enhanced mechanical properties in Al–Si alloys. The experimental and computational insights obtained here are especially crucial for developing predictive models for microstructural evolution of metals under extreme shear deformation.

36 MATERIALS SCIENCE↗
NASA NTRS2002

High-Fidelity Micromechanics Model Developed for the Response of Multiphase Materials

A new high-fidelity micromechanics model has been developed under funding from the NASA Glenn Research Center for predicting the response of multiphase materials with arbitrary periodic microstructures. The model's analytical framework is based on the homogenization technique, but the method of solution for the local displacement and stress fields borrows concepts previously employed in constructing the higher order theory for functionally graded materials. The resulting closed-form macroscopic and microscopic constitutive equations, valid for both uniaxial and multiaxial loading of periodic materials with elastic and inelastic constitutive phases, can be incorporated into a structural analysis computer code. Consequently, this model now provides an alternative, accurate method.

Aboudi, Jacob↗
DOE OSTI2020

Report on the FY20 Characterization of Age Hardened Alloy 709 Materials

This report provides the results on microstructural characterization of the first commercial heat of Alloy 709 plate material undergone additional age hardening treatment. In FY19, through thermodynamic-kinetic modeling and microstructural characterization, it is determined that the 775°C/10 h age-hardening treatment can promote desired precipitation on dislocations and has the potential to further improve the mechanical performance of the material. In FY20, the treatment protocol was applied to the ESR-1150°C condition, and the microstructure was then compared with the ESR-1100°C condition. It was found that the 1150°C solution annealing (SA) dramatically reduced the dislocation density compared to the 1100°C SA, resulting a smaller number density of Nb-rich fine precipitates which grow on dislocations during the age hardening treatment. Other features are very similar between the two. The effect of age hardening on creep performance is discussed. In addition, TEM characterization of a creep-ruptured sample (600°C/330 MPa) was performed. Specimens from the grip region and the gauge region was studied. The grip region specimen was effectively aged at 600°C for extended period, while the gauge region specimen was mechanically deformed at 600°C. The microstructures are very different, implying the importance of a dynamical effect on precipitation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Hardness Prediction by Incorporating Heat Transfer and Molten Pool Fluid Flow in a Multi-pass, Multi-layer Weld for Onsite Repair of Grade 91 steel

Introduction: In the current fleet of fossil-fired power plants, creep strength enhanced ferritic steels (CSEF) are used to sustain the harsh service conditions. Enhanced properties of Grade 91 steel result from tempered martensite with a fine distribution of MX and M23C6 carbides. Grade 91 steel is subjected to onsite welding repair to remedy their degradation due to extreme service condition. Knowledge of weld repairability of these steels, such as as-welded hardness distribution, is essential to establishing sound repair procedures. Experimental trial and error tests can consume a lot of time as many welding variables need to be studied. For numerical modelling, most of the multi-pass multi-layer models are based on finite element method, which are limited to solve the heat conduction equation and ignore convective heat transfer due to melt flow. Moreover, the mesh has to be pre-built based on a known or assumed weld cross-section geometry. These finite element based models thus have limited predictive capability as defects are not considered and nugget size are pre-assumed. This research aims at developing a thermal and microstructure evolution model incorporating molten pool dynamics in a multi-pass multi-layer material deposition to predict the as-welded hardness distribution. Technical Approach: All the thermal, physical, and metallurgical properties of Grade 91 as a function of temperature are collected from the literature and inputted into the thermo-fluid model based on Flow-3D, a computational fluid dynamics software. A multi-pass, multi-layer material deposition is simulated where the melting of filler wire into the molten pool is directly considered based on the volume of fluid (VOF) method. The flow behaviour of the molten pool is used to understand the formation of deposition geometry and defects. The temperature profiles during the multi-pass, multi-layer welding are calculated. The results computed using the new model are compared against the experimental data of fusion zone geometry and thermal cycles. Hardness prediction in the heat-affected zone (HAZ) are made using Johnson-Mehl-Avrami (JMA) equation for solid-state phase transformation kinetics. The JMA parameters are extracted from the experimental data available in the literature. For comparison, a standard finite element heat conduction model is also developed to predict the thermal cycles and hardness distribution in the multi-pass, multi-layer weld. Expected Result: Results obtained using the molten pool dynamic simulation versus the finite element heat conduction model are compared. Specifically, the effects of convective heat transfer on the accuracy of the calculated thermal history, bead shape and size, and HAZ hardness distribution are examined.

Modeling, Grade 91 steel, Multi-pass multi-layer d↗
DOE OSTI2024

Phase Composition and Phase Transformation of Additively Manufactured Nickel Alloy 718 AM Bench Artifacts

Additive manufacturing (AM) technologies offer unprecedented design flexibility but are limited by a lack of understanding of the material microstructure formed under their extreme and transient processing conditions and its subsequent transformation during post-build processing. As part of the 2022 AM Bench Challenge, sponsored by the National Institute of Standards and Technology, this study focuses on the phase composition and phase evolution of AM nickel alloy 718, a nickel-based superalloy, to provide benchmark data essential for the validation of computational models for microstructural predictions. Here, we employed high-energy synchrotron X-ray diffraction, in situ synchrotron X-ray scattering, as well as high-resolution transmission electron microscopy for our analyses. The study uncovers critical aspects of the microstructure in its as-built state, its transformation during homogenization, and its phase evolution during subsequent aging heat treatment. Specifically, we identified secondary phases, monitored the dissolution and coarsening of microstructural elements, and observed the formation and stability of γ ’ and γ ” phases. The results provide the rigorous benchmark data required to understand the atomic and microstructural transformations of AM nickel alloy 718, thereby enhancing the reliability and applicability of AM models for predicting phase evolution and mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Identification of crystal plasticity model parameters by multi-objective optimization integrating microstructural evolution and mechanical data

Crystal plasticity models evolve a polycrystalline yield surface using meso-scale descriptions of deformation mechanisms. The activation of deformation mechanisms is governed by crystallography and a set of model parameters, which are typically calibrated through the fitting of mechanical data such as stress–strain curves and elastic lattice strains. Microstructural data such as phase fractions and texture evolution are used for verifying crystal plasticity parameters. In this study, we use a multi-objective genetic algorithm to identify hardening parameters from flow stress curves with an option to incorporate texture into the optimization approach. Robust, generalized objective functions are developed and used to identify sets of parameters pertaining to dislocation density-based hardening laws in visco-plastic and elasto-plastic self-consistent (VPSC and EPSC) homogenization models. First, the parameters are identified for pure Nb directly from texture using an objective function based on generalized spherical harmonics. Since texture evolution is driven by the relative contribution of active slip systems, the parameters governing the evolution of slip resistance ratios can be recovered from fitting discrete textures at a series of strains. Next, a comprehensive set of load reversal data for dual phase (DP) 780 steel is used to fit a hardening law and a back-stress law in EPSC. Finally, parameters pertaining to a complex hardening law for the evolution of slip and twinning in pure α-Ti are identified. Remarkably, using texture as an objective in combination with stress–strain objectives constrains the model of Ti to fully reproduce not only stress–strain and texture evolution but also hierarchical twinning measurements as a function of initial grain size and texture. Furthermore, given an appropriate model fit to representative experimental texture evolution, underlying twin volume fractions contributing to texture evolution can be predicted.

42 ENGINEERING↗
NASA NTRS2002

High-Fidelity Generalization Method of Cells for Inelastic Periodic Multiphase Materials

An extension of a recently-developed linear thermoelastic theory for multiphase periodic materials is presented which admits inelastic behavior of the constituent phases. The extended theory is capable of accurately estimating both the effective inelastic response of a periodic multiphase composite and the local stress and strain fields in the individual phases. The model is presently limited to materials characterized by constituent phases that are continuous in one direction, but arbitrarily distributed within the repeating unit cell which characterizes the material's periodic microstructure. The model's analytical framework is based on the homogenization technique for periodic media, but the method of solution for the local displacement and stress fields borrows concepts previously employed by the authors in constructing the higher-order theory for functionally graded materials, in contrast with the standard finite-element solution method typically used in conjunction with the homogenization technique. The present approach produces a closed-form macroscopic constitutive equation for a periodic multiphase material valid for both uniaxial and multiaxial loading. The model's predictive accuracy in generating both the effective inelastic stress-strain response and the local stress said inelastic strain fields is demonstrated by comparison with the results of an analytical inelastic solution for the axisymmetric and axial shear response of a unidirectional composite based on the concentric cylinder model, and with finite-element results for transverse loading.

Aboudi, Jacob↗
DOE OSTI2025

Generalizable Image Segmentation for Microstructure Characterization Through Integrated SEM and EBSD Analysis

We demonstrate generalizable semantic segmentation using minimal ground truth data. Correlated scanning electron microscopy (SEM) images and electron backscatter diffraction (EBSD) measurements of frictionstir processed 316L stainless steel plates were used to train deep learning models for grain boundary segmentation. Secondary electron (SE) imaging taken at an accelerating voltage of 10 keV correlated to EBSD-derived grain boundaries produced the best performing model. Notably, an ensemble of three models trained on a single SE image produced accurate segmentation over a series of BSE images of samples manufactured under different processing parameters, with a resultant mean absolute error in grain size of 0.34 µm. The striking generalizability of the models likely results from the similar escape depths of the SE training input and the EBSD training output and the reduced probability of dislocation artifacts appearing in the image. This finding highlights the importance of considering the physical principles behind imaging in the development of robust segmentation models for microstructure characterization.

Taufique, Mohammad Fuad Nur↗
NASA NTRSDate not supplied

Microstructure Quantification and Random Forest Regression Models for Li4Ti5O12–Ni Property Prediction

All-solid-state structural lithium-ion batteries are sought to enable all-electric propulsion in next generation aerospace concepts through improved safety and systems level weight savings. In this work, the influence of processing conditions on microstructural evolution was evaluated for anode composites of strain-free Li4Ti5O12 and metallic nickel current collector. Beyond size distributions, this study explored methods of quantifying microstructural features that describe changes in the spatial distribution and coalescence of nickel particles as a function of sample composition and sintering conditions. Processing-microstructure-property relationships were described by microstructure quantifiers including nickel particle count per area, nearest neighbor distance distribution, and edge-to-edge distance distribution. Machine learning methods were applied to compare the relative influence of processing conditions and microstructural features on electrical conductivity and mechanical strength to optimize for simultaneous energy storage and load bearing performance. Insights gained from this work inform future evaluation of alternative energy storage materials and microstructures for multifunctional performance, and generation of microstructural descriptors strengthens modeling across length scales.

anode↗
DOE OSTI2023

Self-supervised learning of spatiotemporal thermal signatures in additive manufacturing using reduced order physics models and transformers

Microstructure control via additive manufacturing has enormous potential as manufacturers, materials scientists, and designers alike seek to exploit novel fabrication technologies to improve component performance. Recent works have demonstrated the feasibility of producing materials with controlled microstructures across various length scales. However, the experimental approach towards exploring the process-structure space can be laborious and costly. This is particularly true if also considering scan pattern optimization which is well suited for processes such as powder bed fusion electron beam melting. In this work we propose an approach for encoding additive manufacturing layer-wise thermal response signatures using self-supervised representation learning. Thermal simulations from a reduced order model are utilized to estimate the spatiotemporal response during printing. A machine learning framework, using video-transformers, is utilized to efficiently distill spatiotemporal patterns into a compact latent space representation. This latent state representation encodes the relevant physics which is then utilized to establish a data-driven process-structure model for an additively manufactured Ni-based superalloy. In conclusion, the proposed methodology could potentially be used towards in-situ process monitoring, scan pattern experimental design, and component qualification.

97 MATHEMATICS AND COMPUTING↗