Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Membrane Carbonation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

One-step fabrication of robust lithium ion battery separators by polymerization-induced phase separation

Conventional lithium ion battery separators are microporous polyolefin membranes that play a passive role in the electrochemical cell. Next generation separators should offer significant performance enhancements, while being fabricated through facile, low cost approaches with the ability to readily tune physicochemical properties. This study presents a single-step manufacturing technique based on UV-initiated polymerization-induced phase separation (PIPS), wherein microporous separators are fabricated from multifunctional monomers and ethylene carbonate (EC), which functions as both the pore-forming agent (porogen) and electrolyte component in the electrochemical cell. By controlling the ratio of the 1,4-butanediol diacrylate (BDDA) monomer to ethylene carbonate, monolithic microporous membranes are readily prepared with 25 μm thickness and pore sizes and porosities ranging from 6.8 to 22 nm and 15.4% to 38.5%, respectively. With 38.5% apparent porosity and an average pore size of 22 nm, the poly(1,4-butanediol diacrylate) (pBDDA) separator takes up 127% liquid electrolyte, resulting in an ionic conductivity of 1.98 mS cm –1 , which is greater than in conventional Celgard 2500. Lithium ion battery half cells consisting of LiNi 0.5 Mn 0.3 Co 0.2 O 2 cathodes and pBDDA separators were shown to undergo reversible charge/discharge cycling with an average discharge capacity of 142 mA h g –1 and a capacity retention of 98.4% over 100 cycles – comparable to cells using state-of-the-art separators. Moreover, similar discharge capacities were achieved in rate performance tests due to the high ionic conductivity and electrolyte uptake of the film. Finally, the pBDDA separators were shown to be thermally stable to 374 °C, lack low temperature thermal transitions that can compromise cell safety, and exhibit no thermal shrinkage up to 150 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Molecular dynamics study of carbon dioxide and nitrogen selectivity through poly[bis((methoxyethoxy)ethoxy)phosphazene] (MEEP) membrane

Here, a molecular dynamics simulation model was developed to comprehensively understand carbon dioxide over nitrogen (CO 2 /N 2 ) selectivity through polyphosphazene-based membrane comprising of poly[bis((methoxyethoxy)ethoxy)phosphazene] (MEEP) selective layer at the molecular level. The effects of temperature, pressure, and initial feed gas composition on the CO 2 transport on a polymer membrane were studied. The computed free energy and density profile of the permeating gas mixture exhibited that CO 2 molecules express higher interactions with the membrane than N 2 molecules, resulting in higher CO 2 /N 2 selectivity. Statistical analysis of gas molecules (CO 2 , water (H 2 O), and N 2 ) transportation suggested that hydro- and CO 2 -philic functional groups in the membrane significantly impact CO 2 permeability and CO 2 /N 2 selectivity. This study suggested that Lewis acid–base and hydrogen bonding combinations contribute to CO 2 permeation and CO 2 /N 2 selectivity. An equal CO 2 /N 2 selectivity was observed with and without water vapor in the feed gas suggesting that water does not hinder CO 2 transport through the membrane.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Poly(ether‐block‐amide) membrane with deformability and adjustable surface hydrophilicity for water purification

Abstract Freshwater resources are currently insufficient, and another form of freshwater resources, namely, ice, is very interesting except for the issue of how to use new materials for effective purification during the processing procedure. In this article, a new membrane material with multisize pore structure in the cross‐section and intact thin skin layer on the upper and lower surfaces was successfully prepared by adding porogen, filler and setting heating environment during the phase separation process. The membrane exhibits excellent axial deformability, and its elongation at break can reach to 160% strain. Meanwhile, they all show elastic deformation behavior in the range from −60 to 100°C. Even if high content of hydrophobic filler is compounded into these membranes, that is, 5.7 wt% carbon tube content, water contact angle of membrane's surface is only 72.5°, demonstrating obvious hydrophilicity. In addition, in the water purification process, the adsorption rate constant reached ideal value of 0.26 s −1 , and the equilibrium adsorption capacity was about 2.8 g/g, showing fast and efficient water purification ability. In the mode of external heating source or the membrane's heat dissipation, these prepared membranes can melt the ice to obtain purified water and exhibit a controllable purification ability in this process.

Ge, Chengbiao↗
NASA NTRS2016

Demonstration of Robustness and Integrated Operation of a Series-Bosch System

Manned missions beyond low Earth orbit will require highly robust, reliable, and maintainable life support systems that maximize recycling of water and oxygen. Bosch technology is one option to maximize oxygen recovery, in the form of water, from metabolically-produced carbon dioxide (CO2). A two stage approach to Bosch, called Series-Bosch, reduces metabolic CO2 with hydrogen (H2) to produce water and solid carbon using two reactors: a Reverse Water-Gas Shift (RWGS) reactor and a carbon formation (CF) reactor. Previous development efforts demonstrated the stand-alone performance of a NASA-designed RWGS reactor designed for robustness against carbon formation, two membrane separators intended to maximize single pass conversion of reactants, and a batch CF reactor with both transit and surface catalysts. In the past year, Precision Combustion, Inc. (PCI) developed and delivered a RWGS reactor for testing at NASA. The reactor design was based on their patented Microlith® technology and was first evaluated under a Phase I Small Business Innovative Research (SBIR) effort in 2010. The RWGS reactor was recently evaluated at NASA to compare its performance and operating conditions with NASA's RWGS reactor. The test results will be provided in this paper. Separately, in 2015, a semi-continuous CF reactor was designed and fabricated at NASA based on the results from batch CF reactor testing. The batch CF reactor and the semi-continuous CF reactor were individually integrated with an upstream RWGS reactor to demonstrate the system operation and to evaluate performance. Here, we compare the performance and robustness to carbon formation of both RWGS reactors. We report the results of the integrated operation of a Series-Bosch system and we discuss the technology readiness level.

Abney, Morgan B.↗
DOE OSTI2025

Energy-efficient carbon capture from industrial point sources via commercially available green solvent and hollow fiber membrane contactors

Solvent-based absorption systems have emerged in the carbon capture space due to their high absorption capacities, reusability, and favorable energy requirements. Using diethyl sebacate as a solvent for pre- and post-combustion carbon capture has advantages over other solvents, including high hydrophobicity, low viscosity, low vapor pressure, high CO 2 solubility, high CO 2 selectivity, and being commercially available in large quantities. Despite these advantageous properties, the use of diethyl sebacate as a solvent for post-combustion carbon capture has not been studied in detail. To examine the capability of diethyl sebacate, a scalable, energy-efficient, hollow fiber membrane (microporous polypropylene and polyvinylidene fluoride) contactor (HFMC)-based process with low-cost and high surface area is investigated. A purity of 95.3 % CO 2 with 46 % recovery in one absorption stage was achieved, with a permeate flux over one magnitude greater than using a deep eutectic solvent in the same system. Technoeconomic analysis determined a ∼ 0.8 GJ per ton of CO 2 at a processing cost of ∼$93 per ton of CO 2 . Results from this work underscore the potential for utilizing green solvents in HFMC-based separation processes for effective carbon capture and provide a pathway towards practical deployment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Water as a gas separation membrane

Efficient gas separation membranes are essential for carbon capture, biogas upgrading, and hydrogen purification. Inspired by how plants absorb CO 2 through water, we present a membrane platform that uses liquid water as the selective layer. Hydrophilic sub-100-nm pores stabilize water through strong capillary forces, enabling operation at feed pressures above 72 bar under dry and humid conditions. Selectivity is governed by gas solubility in water, while permeance is tuned by adjusting the water layer thickness. Reducing this thickness below 200 nm yields CO 2 permeances up to 11,600 gas permeation units with CO 2 :N 2 , CO 2 :CH 4 , and CO 2 :H 2 selectivities of 40, 26, and 31, respectively, surpassing the performance of state-of-the-art membranes. Operation is sustained for over a week without water loss, and performance scales using commercially available porous polymer supports under mixed-gas crossflow conditions. Water’s dissolution-based transport avoids saturation and reaction-rate limits, enabling a robust, high-performance, and environmentally benign gas separation platform.

08 HYDROGEN↗
DOE OSTI2020

Probing the electrical double layer by operando X‐ray photoelectron spectroscopy through a graphene‐carbon nanotube composite window

Abstract The electrical double layer is known to spontaneously form at the electrode‐electrolyte interface, impacting many important chemical and physical processes as well as applications including electrocatalysis, electroorganic synthesis, nanomaterial preparation, energy storage, and even emulsion stabilization. However, it has been challenging to study this fundamental phenomenon at the molecular level because the electrical double layer is deeply “buried” by the bulk electrolyte solution. Here, we report a quantitative probing of the electrical double layer of ionic liquids from the solid side of a photoelectron‐transparent graphene‐carbon nanotube hybrid membrane electrode using X‐ray photoelectron spectroscopy. The membrane window is ultrathin (1‐1.5 nm), large (~1 cm 2 ), and robust, enabling a tight seal of the electrolyte and quantitative measurement with excellent photoelectron signals. By operando monitoring the population changes of cations and anions in response to the applied electrical potentials, we experimentally resolve the chemical structure and dynamics of the electrical double layer, which corroborate results from molecular dynamics simulations. image

Wang, Peng↗
NASA NTRS2004

Direct Electrolytic Deposition of Mats of Mn(x)O(y) Nanowires

Mats of free-standing manganese oxide (MnxOy) nanowires have been fabricated as experimental electrode materials for rechargeable electrochemical power cells and capacitors. Because they are free-standing, the wires in these mats are electrochemically accessible. The advantage of the mat-of-nanowires configuration, relative to other configurations of electrode materials, arises from the combination of narrowness and high areal number density of the wires. This combination offers both high surface areas for contact with electrolytes and short paths for diffusion of ions into and out of the electrodes, thereby making it possible to charge and discharge at rates higher than would otherwise be possible and, consequently, to achieve greater power densities. The nanowires are fabricated in an electrolytic process in which there is no need for an electrode binder material. Moreover, there is no need to incorporate an electrically conductive additive into the electrode material; the only electrically conductive material that must be added is a thin substrate contact film at the anchored ends of the nanowires. Hence, the mass fraction of active electrode material is close to 100 percent, as compared with about 85 percent in conventional electrodes made from a slurry of active electrode material, binder, and conductive additive pressed onto a metal foil. The locations and sizes of the nanowires are defined by holes in templates in the form of commercially available porous alumina membranes. In experiments to demonstrate the present process, alumina membranes of various pore sizes and degrees of porosity were used. First, a film of Au was sputtered onto one side of each membrane. The membranes were then attached, variously, to carbon tape or a gold substrate by use of silver or carbon paste. Once thus attached, the membranes were immersed in a plating solution comprising 0.01 M MnSO4 + 0.03 M (NH4)2SO4. The pH of the solution was kept constant at 8 by addition of H2SO4 or NH4OH as needed. Mn(x)O(y) nanowires were potentiostatically electrodeposited in the pores in the alumina templates. Depending on the anodic deposition potentials, Mn(x)O(y) was deposited in various oxidation states [divalent (Mn3O4), trivalent (Mn2O3), or tetravalent (MnO2)]. The Mn(x)O(y) wires were made free-standing (see figure) by dissolving the alumina templates, variously, in KOH or NaOH at a concentration of 20 volume percent.

Myung, Nosang↗
DOE OSTI2020

Ion-exchange membrane with molecular barrier

Disclosed is an ion-exchange membrane that includes a molecular barrier for influencing permeation selectivity through the membrane. The membrane includes fluorinated carbon backbone chains and fluorinated side chains that extend off of the fluorinated carbon backbone chains. The fluorinated side chains include acid groups for ionic conductivity. The acid groups surround and define permeable domains that are free of the fluorinated carbon backbone chains. Molecular barriers are located in the permeable domains and influence permeability through the domains.

25 ENERGY STORAGE↗
DOE OSTI2021

Silica-copper catalyst interfaces enable carbon-carbon coupling towards ethylene electrosynthesis

Membrane electrode assembly (MEA) electrolyzers offer a means to scale up CO 2 -to-ethylene electroconversion using renewable electricity and close the anthropogenic carbon cycle. To date, excessive CO 2 coverage at the catalyst surface with limited active sites in MEA systems interferes with the carbon-carbon coupling reaction, diminishing ethylene production. With the aid of density functional theory calculations and spectroscopic analysis, here we report an oxide modulation strategy in which we introduce silica on Cu to create active Cu-SiO x interface sites, decreasing the formation energies of OCOH* and OCCOH*—key intermediates along the pathway to ethylene formation. We then synthesize the Cu-SiO x catalysts using one-pot coprecipitation and integrate the catalyst in a MEA electrolyzer. By tuning the CO 2 concentration, the Cu-SiO x catalyst based MEA electrolyzer shows high ethylene Faradaic efficiencies of up to 65% at high ethylene current densities of up to 215 mA cm -2 ; and features sustained operation over 50 h.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Sonochemical Synthesis and Ion Transport Properties of Surfactant-Stabilized Carbon Nanotube Porins

Carbon nanotube porins (CNTPs), short segments of carbon nanotubes stabilized by a lipid coating, are a promising example of artificial membrane channels that mimic a number of key behaviors of biological ion channels. While the lipid-assisted synthesis of CNTPs may facilitate their subsequent incorporation into lipid bilayers, it limits the applicability of these pores in other self-assembled membrane materials and also precludes the use of large scale purified CNT feedstocks. In this report we demonstrate that CNTPs can be synthesized by sonochemical cutting of long CNT feedstocks in the presence of different surfactants, producing CNTS with transport properties identical to those obtained by the lipid-assisted procedure. Our results open up a large variety of synthetic routes for CNTP production.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Bench-Scale Testing of a High Efficiency, Ultra-Compact Process for Pre-Combustion CO 2 Capture (Final Report)

The overarching objective of this bench-scale study is to field-validate the technical feasibility of a membrane- and adsorption-enhanced water gas shift (WGS) reaction process that employs a carbon molecular sieve (CMS) membrane reactor (MR) followed by an adsorption reactor (AR) for pre-combustion CO 2 capture while demonstrating progress towards achievement of the overall performance goals of CO 2 capture with 95% CO 2 purity at a cost of electricity (COE) of 30% less than the baseline capture approaches. The main goal of this bench-scale project is to advance the proposed MR-AR transformative CO 2 capture technology to a sufficient maturity level so that our present industrial partners (M&PT and Worley) can potentially adapt the technology for further small pilot-scale testing. The project began at TRL 4, as the system prototype had already been validated in the laboratory on simulated syngas (as part of project DE-FE0026423). The project ended at TRL 5, via scaling-up of the prototype system and testing it on actual syngas at a host site (CAER at the University of Kentucky (UKy)). The project was carried-out in two different phases: In Phase I (during BP1 of the project), the team designed, constructed, and assembled the bench-scale experimental MR-AR system, prepared the membranes, adsorbents, and catalysts, tested the bench-scale unit with simulated syngas to validate functionality, and prepared a preliminary TEA of the technology. In Phase II (during BP2 of the project), the team installed the unit at the test site at the UKy site and completed all utility connections and hookups, field-tested the novel MR-AR process in the bench-scale system using real syngas, collected and analyzed experimental data, and completed a detailed TEA of the technology. A key aim of the project was to identify and address the technical and process risks and to generate information to advance the technology to the next stage of development. All project milestones and success criteria were met. Specifically, the team: (i) designed, constructed and assembled a bench scale system that handled 1 – 5 scfm syngas and tested its functionality with simulated syngas; (ii) prepared high performance CMS membrane tubes (ID: 3.5 mm, OD: 5.7 mm, 30” long) that meet the target H 2 permeance ( > 1 m 3 /(m 2 .hr.bar) or (> 370.3 GPU)) and a target H 2 /CO selectivity >80 at the relevant temperature (up to 300oC) and pressure conditions (up to 25 bar) with a <10% decline in performance over each 250 hr. testing period (iii) procured commercial sour-shift catalyst in sufficient quantity and prepared up to 10 kg of pelletized adsorbent for use at relevant conditions (250oC 2.5wt.% and target sorbent attrition rate < 0.2; (iv) installed the bench-scale unit at the test site (UKy) and tested the MR-AR technology using real syngas for over 250 hr. for both static and flow experiments; (v) updated the TEA analysis based on bench-scale data and met CO 2 capture goals of 95% CO 2 purity at a cost of electricity 30% less than baseline capture approaches. The CMS membranes, HTC adsorbents and catalysts employed all exhibited very robust and stable performance during the long-term run (over a >250 hr live syngas run). Furthermore, the proposed MR-AR IGCC system achieved a LCOE with a N 2 sale price of $\$$ 30/ton, with N 2 compression (no N 2 compression) of 101.2 $\$$/MWh (95.3 $\$$/MWh), which represents a 29.8% (33.9%) LCOE reduction in the baseline IGCC with carbon capture of 144.2 $\$$/MWh. The proposed MR-AR IGCC delivers a CO 2 capture cost of 44.8 $\$$/tonne (39.9 $\$$/tonne) vs 98.1 $\$$/tonne of the baseline capture case and a net power production of 586 MWe (623 MWe) vs 556 MWe of the baseline capture case.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Recent Progress in the Engineering of Polymeric Membranes for CO2 Capture from Flue Gas

CO2 capture from coal- or natural gas-derived flue gas has been widely considered as the next opportunity for the large-scale deployment of gas separation membranes. Despite the tremendous progress made in the synthesis of polymeric membranes with high CO2/N2 separation performance, only a few membrane technologies were advanced to the bench-scale study or above from a highly idealized laboratory setting. Therefore, the recent progress in polymeric membranes is reviewed in the perspectives of capture system energetics, process synthesis, membrane scale-up, modular fabrication, and field tests. These engineering considerations can provide a holistic approach to better guide membrane research and accelerate the commercialization of gas separation membranes for post-combustion carbon capture.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Key Features of Polyimide-Derived Carbon Molecular Sieves

Carbon molecular sieve (CMS) membranes have impressive separation properties; however, both chemical and morphology structures need to be understood better. Here we characterize CMS with the simplest polyimide (PI) PMDA/pPDA (PMDA=pyromellitic dianhydride, pPDA=p-phenylenediamine), using FTIR, solid-state 15 N-NMR and 13 C-NMR, XPS, XRD, and Raman spectra to study chemical structure. Here we also compare gas separation properties for this CMS to a CMS derived from a more conventional PI precursor. The detailed characterization shows the presence of aromatic pyridinic, pyrrolic rings as well as graphitic, pyridonic components and a few other groups in both CMS types derived from the very different precursors. The CMS morphologies, while related to precursor and pyrolysis temperature details, show similarities consistent with a physical picture comprising distributed molecular sieving plate-like structures. These results assist in understanding diverse CMS membrane separation performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Nanoporous membranes for fast diffusion of ions and small molecules

A product includes a nanoporous membrane having a plurality of carbon nanotubes and a fill material in interstitial spaces between the carbon nanotubes for limiting or preventing fluidic transfer between opposite sides of the nanoporous membrane except through interiors of the carbon nanotubes. The longitudinal axes of the carbon nanotubes are substantially parallel, an average inner diameter of the carbon nanotubes is about 20 nanometers or less, and both ends of at least some of the carbon nanotubes are open. Moreover, the fill material is impermeable or having an average porosity that is less than the average inner diameter of the carbon nanotubes.

Buchsbaum, Steven F.↗
NASA NTRS1998

Biochemical Capture and Removal of Carbon Dioxide

We devised an enzyme-based facilitated transport membrane bioreactor system to selectively remove carbon dioxide (CO2) from the space station environment. We developed and expressed site-directed enzyme mutants for CO2 capture. Enzyme kinetics showed the mutants to be almost identical to the wild type save at higher pH. Both native enzyme and mutant enzymes were immobilized to different supports including nylons, glasses, sepharose, methacrylate, titanium and nickel. Mutant enzyme could be attached and removed from metal ligand supports and the supports reused at least five times. Membrane systems were constructed to test CO2 selectivity. These included proteic membranes, thin liquid films and enzyme-immobilized teflon membranes. Selectivity ratios of more than 200:1 were obtained for CO2 versus oxygen with CO2 at 0.1%. The data indicate that a membrane based bioreactor can be constructed which could bring CO2 levels close to Earth.

Trachtenberg, Michael C.↗