Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Materials Compatibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Compositional dependence of linear and nonlinear optical response in crystalline hafnium zirconium oxide thin films

Composition dependence of second harmonic generation, refractive index, extinction coefficient, and optical bandgap in 20 nm thick crystalline Hf 1– x Zr x O 2 (0 ≤ x ≤ 1) thin films is reported here. The refractive index exhibits a general increase with increasing ZrO 2 content with all values within the range of 1.98–2.14 from 880 nm to 400 nm wavelengths. A composition dependence of the indirect optical bandgap is observed, decreasing from 5.81 eV for HfO 2 to 5.17 eV for Hf 0.4 Zr 0.6 O 2 . The bandgap increases for compositions with x > 0.6, reaching 5.31 eV for Hf 0.1 Zr 0.9 O 2 . Second harmonic signals are measured for 880 nm incident light. The magnitude of the second harmonic signal scales with the magnitude of the remanant polarization in the composition series. Film compositions that display near zero remanent polarizations exhibit minimal second harmonic generation while those with maximum remanent polarization also display the largest second harmonic signal. The results are discussed in the context of ferroelectric phase assemblage in the hafnium zirconium oxide films and demonstrate a path toward a silicon-compatible integrated nonlinear optical material.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Radiative cooling textiles using industry-standard particle-free nonporous micro-structured fibers

Abstract Thermal radiation is a major dissipative pathway for heat generated by the human body and offers a significant thermoregulation mechanism over a wide range of conditions. We could use this in garment design to enhance personal cooling, which can improve the wearing comfort of garments or even result in energy savings in buildings. At present, however, radiative cooling has received insufficient attention in commercial design and production of textiles for wearable garments. Textiles that efficiently transmit the radiative heat were recently demonstrated, but either do not utilize standard weaving and knitting processes for wearable garments or require substantial process modifications. Here, we demonstrate the design and implementation of large-scale radiative cooling textiles for localized cooling management and enhanced thermal comfort using industry-standard particle-free nonporous micro-structured fibers that are fully compatible with standard textile materials and production methods. The micro-structured fibers, yarns and fabrics are part of a hierarchical photonic structure design that renders the textiles highly infrared transparent (up to > 0.8) while assuring visual opacity (up to 0.99). We design radiative cooling textiles with first-principles electromagnetic methods and fabricate them using commercial textile materials and formation facilities. Our “fabless” approach is confirmed by very good quantitative agreement between design and measurements. The resulting fabrics exhibit wearability properties expected of wearable textiles, and lower skin temperature by ≥ 3 °C compared to conventional textiles, which offers the potential for > 30 % energy savings in buildings and increases wearing comfort by significantly reducing the reliance on latent heat dissipation for thermoregulation.

Catrysse, Peter B.↗
DOE OSTI2024

MARVEL Corrosion Test Interim Report

This study explores eutectic gallium-indium-tin (e-GaInSn) as a potential coolant for the intermediate heat exchanger for the MARVEL microreactor. E-GaInSn has an exceptionally low melting point of 10.8 °C and a high boiling point exceeding 1300 °C [4]. This wide temperature range provides designers with a significant margin to coolant boiling, even under severe accident conditions. Moreover, e-GaInSn is highly stable in both air and water demonstrating a high coefficient of thermal conductivity compared to conventional coolants like water or polymer-based solutions, along with a large heat capacity and low vapor pressure [5, 6]. While its heat transfer characteristics may not match those of some other liquid metals such as sodium, they are still quite favorable [6]. More importantly, gallium does not present issues related to chemical activity in a nuclear reactor environment. These unique and advantageous properties make e-GaInSn an attractive option for reactor applications. However, it is essential to thoroughly evaluate the compatibility of E-GaInSn with structural materials, particularly steels, for which it has a relatively high affinity. Presently, the compatibility data for these liquid metals or alloys with candidate structural materials remains limited, underscoring the need for further research to ascertain their suitability as liquid breeders or coolants [7

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Materials Selection Principles for Designing Electro‐Thermal Neurons

Artificial neurons exhibiting volatile threshold switching and action potential‐like oscillations are crucial for brain‐inspired computing. While Complimentary Metal‐Oxide‐Semiconductor (CMOS)‐based strategies require hundreds of transistors to simulate each neuron, neuronal oscillations arise spontaneously in individual electro‐thermal devices due to nonlinearities like the Mott transition in VO 2 . Despite improved understanding of the physics, quantitative connections between neuronal performance and material properties remain under‐explored, preventing predictive neuron design and rational materials selection. In this work, a physics‐aware forward design methodology is developed for interrogating a wide palette of materials with properties varying by orders of magnitude, and their performance (high frequency, high dynamical reconfigurability and low power) under external circuit and device geometry constraints is assessed. The space of viable materials is identified to be much larger than previously recognized, with candidates from a range of materials classes, including Ge, GaP and MoS 2 . CMOS‐compatible performance (such as 100 GHz oscillating frequencies) can be achieved with CMOS‐compatible node sizes (≈10 nm). Finally, combinations of material properties yielding desired neuronal performance under uncertain design constraints are considered. This work solidifies forward design principles for electro‐thermal neuron devices, a necessary pre‐condition for inverse design from desired neuronal performance to required materials properties.

compact model↗
DOE OSTI2023

Advanced supramolecular design for direct ink writing of soft materials

The exciting advancements in 3D-printing of soft materials are changing the landscape of materials development and fabrication. Among various 3D-printers that are designed for soft materials fabrication, the direct ink writing (DIW) system is particularly attractive for chemists and materials scientists due to the mild fabrication conditions, compatibility with a wide range of organic and inorganic materials, and the ease of multi-materials 3D-printing. Inks for DIW need to possess suitable viscoelastic properties to allow for smooth extrusion and be self-supportive after printing, but molecularly facilitating 3D printability to functional materials remains nontrivial. While supramolecular binding motifs have been increasingly used for 3D-printing, these inks are largely optimized empirically for DIW. Hence, this review aims to establish a clear connection between the molecular understanding of the supramolecularly bound motifs and their viscoelastic properties at bulk. Herein, extrudable (but not self-supportive) and 3D-printable (self-supportive) polymeric materials that utilize noncovalent interactions, including hydrogen bonding, host–guest inclusion, metal–ligand coordination, micro-crystallization, and van der Waals interaction, have been discussed in detail. In particular, the rheological distinctions between extrudable and 3D-printable inks have been discussed from a supramolecular design perspective. Examples shown in this review also highlight the exciting macroscale functions amplified from the molecular design. Challenges associated with the hierarchical control and characterization of supramolecularly designed DIW inks are also outlined. The perspective of utilizing supramolecular binding motifs in soft materials DIW printing has been discussed. Finally, this review serves to connect researchers across disciplines to develop innovative solutions that connect top-down 3D-printing and bottom-up supramolecular design to accelerate the development of 3D-print soft materials for a sustainable future.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Feasibility Studies and Downselection of New Materials and Manufacturing Technologies for Nuclear Applications

This report is intended to present the results of multi-laboratory collaborative studies on the feasibility and downselection of the structural materials that are newly considered for application to future nuclear energy technologies. The Advanced Materials and Manufacturing Techniques (AMMT) program has been implemented to develop cross-cutting technologies in support of a broad range of nuclear reactor technologies and to maintain U.S. leadership in materials and manufacturing technologies for nuclear energy applications. In line with these program objectives, this collaborative studies aim to explore new materials utilizing advanced manufacturing technologies. The FY23 research scope consists of the feasibility studies on new materials and relevant advanced manufacturing technologies, collection of materials properties data and knowledge through experiments and literature survey, and development and application of decision criteria matrix for downselecting candidate materials and manufacturing technologies. The three-laboratory efforts for FY23 have focused on the three new material groups including oxide dispersion strengthened (ODS) materials, refractory composites and alloys, and high entropy alloys (HEAs) investigated, respectively, by Oak Ridge National Laboratory (ORNL) (work package: CT-23OR130406), Los Alamos National Laboratory (LANL) (CT-23LA130403) and Pacific Northwest National Laboratory (PNNL) (CT-23PN130408). The execution of this multi-lab research aimed to provide the AMMT program a merit-based feasibility study identifying an accelerated development path for these materials. A collaborative approach for achieving this goal was to develop a common materials evaluation criteria matrix and apply to all new candidate materials for the evaluation and prioritization of new materials using advanced manufacturing processes. The decision criteria matrix created is a matrix of criteria which a prospective material is scored against. The evaluation criteria are divided into four categories: Application Space, Environmental Compatibility, Physical & Mechanical Properties, and Manufacturability. Materials are given a score from 1−5 for each criterion, with the highest score (5) essentially mean that a material has the most near-term potential for application. Application of the decision criteria matrix will provide guidance to the future research on new materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Lateral Integration of SnS and GeSe van der Waals Semiconductors: Interface Formation, Electronic Structure, and Nanoscale Optoelectronics

The emergence of atomically thin crystals has allowed extending materials integration to lateral heterostructures where different 2D materials are covalently connected in the plane. The concept of lateral heterostructures can be generalized to thicker layered crystals, provided that a suitably faceted seed crystal presents edges to which a compatible second van der Waals material can be attached layer by layer. Here, we examine the possibility of integrating multilayer crystals of the group IV monochalcogenides SnS and GeSe, which have the same crystal structure, small lattice mismatch, and similar bandgaps. In a two-step growth process, lateral epitaxy of GeSe on the sidewalls of multilayer SnS flakes (obtained by vapor transport of a SnS 2 precursor on graphite) yields heterostructures of laterally stitched crystalline GeSe and SnS without any detectable vertical overgrowth of the SnS seeds and with sharp lateral interfaces. Combined cathodoluminescence spectroscopy and ab initio calculations show the effects of small band offsets on carrier transport and radiative recombination near the interface. Further, the results demonstrate the possibility of forming atomically connected lateral interfaces across many van der Waals layers, which is promising for manipulating optoelectronics, photonics, and for managing charge- and thermal transport.

2D layered crystals↗
DOE OSTI2020

Corrosion of 304 stainless steel in static liquid lithium under high vacuum

To study the compatibility especially the corrosion characteristic of structural material stainless steel (SS) with liquid lithium (Li) is an important factor for the simultaneous application of liquid Li and SS as a blanket material or potential plasma facing material (PFM) in future fusion devices. Here, the corrosion behaviors of 304SS exposed to liquid Li at 700 K for 1320 hr under high vacuum were investigated. After exposure to liquid Li, 304SS produces non-uniform corrosion which includes corrosion products and grain boundary corrosion. Compared with the corrosion behaviors at 600 K and 640 K, temperature plays an important role in the corrosion behaviors of 304SS in static liquid Li. The weight loss, corrosion depth and corrosion products of 304SS specimens increase with the corrosion temperature. In general, the compatibility between 304SS and static liquid Li is relatively good under the experimental conditions. And besides, it is unexpectedly found that the compatibility of copper with Li is not good.

304SS↗
DOE OSTI2022

Ferrite Specification for the Mu2e 300 kHz and 4.4 MHz AC Dipole Magnets

The Mu2e experiment at Fermilab will measure the rate for neutrinoless-conversion of negative muons into electrons with never-before-seen precision. This experiment will use a pulsed 8 GeV proton beam with pulses separated by 1.7 µs. To suppress beam induced backgrounds to this process, a set of dipoles operating at 300 kHz and 4.4 MHz have been developed that will reduce the fraction of out-of-time protons at the level of 1E-10 or less. Selection of magnetic ferrite material for construction must be carefully considered given the high repetition rate and duty cycle that can lead to excess heating in conventional magnetic material. A model of the electromagnetic and thermal properties of candidate ferrite materials has been constructed. Magnetic permeability, inductance, and power loss were measured at the two operating frequencies in toroidal ferrite samples as well as in the ferrites from which prototype magnets were built. Additionally, the outgassing rates of the ferrite material was measured to determine vacuum compatibility. The outcome of this work is a detailed specification of the electrical and mechanical details of the ferrite material required for this application.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

State of Innovation 2025: Progress in Accelerating Next-Generation Cement and Concrete Technologies

The cement and concrete sectors are entering a decisive period as next-generation technologies advance from laboratory research to demonstration, early deployment, and first-of-a-kind commercial plants. Building on the 2024 State of Innovation report, the 2025 outlook highlights both the rapid acceleration of innovation and the urgent need for coordinated action across the value chain. Venture capital activity into the cement and concrete space stabilized following the record surge of 2022-2023, yet landmark financings, such as Sublime Systems' $200 million round and Terra CO2's $124 million Series B, signal continued investor confidence in companies approaching commercialization. Corporate procurement has become a powerful new catalyst, with Microsoft, Amazon, and CRH (Cement Roadstone Holdings) Ventures providing long-term commitments that underpin the first wave of next-generation cementitious products. The sector is shifting from early-stage experimentation toward the scaling of well-capitalized leaders capable of bridging the critical "capitalization gap." Early innovators continue to expand the toolkit through novel binders, electrochemical cements, biogenic limestone, and carbonate mineralization pathways. Going into 2026, cost competitiveness, durability validation, and scalability enabled by resilient supply chains remain the decisive factors for market adoption. At the 2025 Next Generation Cement and Concrete Critical Technologies Meeting, attendees emphasized dual-track funding strategies that integrate federal grants with private capital as key to enabling market breakthrough. State programs and corporate demand are sustaining momentum, while successful companies increasingly demonstrate both economic value and reduced dependence on imported materials. The National Concrete Pavement Technology Center and others underscored that broad integration of next-generation materials will hinge on standards compatibility, verified field performance, and workforce readiness. Colorado continues to serve as a proving ground through pilot programs that combine supplier training, phased implementation, and real-world data to de-risk innovation and provide replicable models for other regions. The 2025 Cement and Concrete Critical Technologies Workshop reinforced that scaling next-generation materials will require alignment among technology innovation, performance validation, and market demand. Stakeholders must move beyond siloed efforts toward collaborative frameworks that coordinate standards, funding, and infrastructure deployment. As a neutral convener and technical validator, the National Laboratory of the Rockies (NLR) plays a pivotal role in bridging innovation and market adoption through collaborative research, technology validation, and entrepreneurship programs. By uniting innovators, incumbents, policymakers, contractors, and investors, NLR and its partners are helping chart a credible pathway toward widespread commercialization in the decade ahead.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Exploring Fission–Fusion Synergies to Accelerate Compatibility Understanding

To address the significant commercial interest in fusion energy, it will be necessary to accelerate the compatibility research associated with liquid breeders including Li, eutectic Pb–Li and LiF-BeF 2 (FLiBe) molten salt. Particularly for FLiBe, compatibility understanding is limited especially for fusion relevant materials such as reduced activation ferritic-martensitic steels, SiC and V alloys. The historical knowledge associated with molten salt reactors (MSRs) and recent work to commercialize MSRs can benefit fusion research. Recent experimental and modeling work has improved understanding and this knowledge can be applied to fusion relevant materials. For liquid metals (LMs), the comparisons to Li and Pb–Li are less direct but nevertheless can help guide the pathway toward commercialization. For Pb–Li, Al-rich coatings have been shown to inhibit dissolution and potentially increase operating temperatures. For commercialization, the experience with sensors and on-line cleanup can help guide future developments. Thus, it is worth considering the potential for fission-related research with LMs and molten salts to help accelerate fusion research.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hole doping in compositionally complex correlated oxide enables tunable exchange biasing

Magnetic interfaces and the phenomena arising from them drive both the design of modern spintronics and fundamental research. Recently, it was revealed that through designing magnetic frustration in configurationally complex entropy stabilized oxides, exchange bias can occur in structurally single crystal films. This eliminates the need for complex heterostructures and nanocomposites in the design and control of magnetic response phenomena. In this work, we demonstrate through hole doping of a high entropy perovskite oxide that tuning of magnetic responses can be achieved. With detailed magnetometry, we show magnetic coupling exhibiting a variety of magnetic responses including exchange bias and antiferromagnetic spin reversal in the entropy stabilized ABO 3 perovskite oxide La 1-x Sr x (Cr 0.2 Mn 0.2 Fe 0.2 Co 0.2 Ni 0.2 )O 3 family. We find that manipulation of the A-site charge state can be used to balance magnetic phase compositions and coupling responses. This allows for the creation of highly tunable exchange bias responses. In the low Sr doping regime, a spin frustrated region arising at the antiferromagnetic phase boundary is shown to directly couple to the antiferromagnetic moments of the film and emerges as the dominant mechanism, leading to a vertical shift of magnetization loops in response to field biasing. At higher concentrations, direct coupling of antiferromagnetic and ferromagnetic regions is observed. This tunability of magnetic coupling is discussed within the context of these three competing magnetic phases, revealing critical features in designing exchange bias through exploiting spin frustration and disorder in high entropy oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ friction and wear behavior of rubber materials incorporating various fillers and/or a plasticizer in high-pressure hydrogen

Polymers are used routinely for equipment and infrastructure in hydrogen vehicle refueling stations, but significant gaps remain in understanding their hydrogen compatibility. The tribological properties of these materials in a high-pressure hydrogen environment is important in preventing component failure and the need for frequent replacement. We present in situ tribological studies on model rubbers, which include common fillers and plasticizer, using an in situ tribometer developed previously. Results suggest a clear, yet complicated, combined effect of the high-pressure hydrogen and the additives on the tribological performance of the chosen materials, as compared to matching experiments performed in ambient air. We find that the additives improved wear resistance in EPDM but deteriorated that in NBR due to disparate additive-polymer interactions.

Kuang, Wenbin↗
DOE OSTI2023

Ab Initio Prediction of Ultra‐Wide Band Gap B x Al 1− x N Materials

Abstract Ultra‐wide bandgap (UWBG) materials are poised to play an important role in the future of power electronics. Devices made from UWBG materials are expected to operate at higher voltages, frequencies, and temperatures than current silicon and silicon‐carbide‐based devices and can even lead to significant miniaturization of such devices. In the UWBG field, aluminum nitride and boron nitride have attracted great interest; however, the B x Al 1− x N alloys are much less studied. In this work, using first‐principles simulations combining density‐functional theory and the cluster expansion method, the crystal structure of B x Al 1− x N alloys is predicted. Seventeen ground state structures of B x Al 1− x N with formation energies between 0.11 and 0.25 eV atom ‐1 are found. All of these structures are found to be dynamically stable. The B x Al 1− x N structures are found to have predominantly a tetrahedral bonding environment; however, some structures exhibit sp 2 bonds similar to hexagonal BN. This work expands knowledge of the structures, energies, and bonding in B x Al 1− x N which aids their synthesis, the innovation of lateral or vertical devices, and discovery of compatible dielectric and Ohmic contact materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Abstract for CRADA between NETL and the University of Massachusetts Lowell (AGMT-1275)

The demand for printed electronics over conventional electronics is growing each year due to their low costs, low material waste during manufacturing, and compatibility with flexible substrates. The development of inks for printed electronics is a challenge because each printing technology requires different viscosities and curing behaviors to create devices with controlled structures at the micron scale, or smaller. Carbon is a great candidate for fabricating printed electronics devices because it is inexpensive and earth abundant, easily functionalized to impart miscibility with solvent systems, and has electrical properties that can be tuned from insulating to conducting. Despite these advantages, carbons are rarely used for printed electronics because there is a scarcity of inks available for non-contact printing technologies. To address these challenges, the National Energy Technology Laboratory (NETL) will collaborate with the University of Massachusetts Lowell (Participant) through its Printed Electronics Research Collaborative (PERC) to develop engineered carbons and ink formulations optimized specifically for printing radio- and microwave-frequency electronic devices using ink jet, aerosol jet, syringe dispensing, and other additive manufacturing techniques. NETL will process coal, petroleum, and other carbon feedstocks to make engineered carbons with the appropriate composition, microstructure, surface functionalization, and particle morphologies needed to stabilize ink suspensions and impart useful electronic properties to printed devices. The University of Massachusetts Lowell will utilize these engineered carbons to determine which solvent systems and ink additives are needed to achieve the appropriate viscosity, stability, and printability to make useful ink formulations. The University of Massachusetts Lowell will then utilize these inks to manufacture printed resistors and conductors using inkjet, aerosol jet, and syringe dispensing printing methods and will characterize device performance using four-point probe resistivity measurements, contact angle measurements to assess wettability, adhesion evaluation to various substrates, and focused ion beam and scanning electron microscopy for surface and density investigations of printed devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A defect-resistant Co–Ni superalloy for 3D printing

Abstract Additive manufacturing promises a major transformation of the production of high economic value metallic materials, enabling innovative, geometrically complex designs with minimal material waste. The overarching challenge is to design alloys that are compatible with the unique additive processing conditions while maintaining material properties sufficient for the challenging environments encountered in energy, space, and nuclear applications. Here we describe a class of high strength, defect-resistant 3D printable superalloys containing approximately equal parts of Co and Ni along with Al, Cr, Ta and W that possess strengths in excess of 1.1 GPa in as-printed and post-processed forms and tensile ductilities of greater than 13% at room temperature. These alloys are amenable to crack-free 3D printing via electron beam melting (EBM) with preheat as well as selective laser melting (SLM) with limited preheat. Alloy design principles are described along with the structure and properties of EBM and SLM CoNi-base materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Oak Ridge National Laboratory Thermoplastic Composite Joining of Pultruded Continuous Fiber Spars for Multi-Functional Battery Enclosure

Oak Ridge National Laboratory (ORNL) worked with DowAksa Industry to investigate the potential of using PA66 material to produce larger composite parts, transcending the limitations of traditional presses. The project aimed to develop a suitable material for printing battery boxes using Nylon 66 infused with 40 wt.% carbon fiber, compatible with the ORNL Additive Manufacturing and Compression Molding (AM-CM) system. However, even with extensive work, it was concluded that the material is not compatible with the AMCM process and suitable for joining using compression technique. Main reason for the incompatibility were found to be very high crystallinity of the PA66 grade chosen for this work. To improve printability, a modifier (proprietary) was added to decrease crystallinity, but this led to reduced thermal stability and adhesion issues.

36 MATERIALS SCIENCE↗