Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MEA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Pilot scale testing of an advanced solvent in a 0.7 MWe post-combustion CO 2 capture unit

An advanced Amine Promoted Buffer Solution (APBS), APBS-CDRMax® (CDRMax), developed by Carbon Clean Solutions Limited (CCSL), was tested at the 0.7 MWe CO 2 capture facility at Kentucky Utilities E.W. Brown Generation Station using a heat-integrated two-staged stripping CO 2 capture process. The performance of the solvent was evaluated to determine operating conditions that maximized the cyclic capacity of the solvent and results in energy savings. The regeneration energy ranged from 2.9 to 3.3 GJ/ton CO 2 with 14 vol % (dry) CO 2 inlet and approximately 90 % capture. The difference in the reboiler specific heat duty at stripper pressures of 1.7 and 2.1 bar was minimal as similar amounts of water vapor were observed in the CO 2 product stream at stripper outlet. Recycling of product CO 2 increased the inlet CO 2 concentration to the absorber from 14 to 16 vol% which enhanced mass transfer from the gas to the solvent resulting in about 5 % reduction in the energy of regeneration at the lower stripper pressure. The solvent circulation rate was reduced by about 30 % relative to previous 30 wt% MEA campaign for the CO 2 target capture of 90 %. Finally, the reduced solvent make-up rate of CDRMax shows promise for capital and operating cost savings for post-combustion CO 2 capture.

42 ENGINEERING↗
DOE OSTI2022

Research on oxygen solubility in aqueous amine solvents with common additives used for CO 2 chemical absorption

Oxidative degradation in amine based post-combustion carbon capture (PCCC) leads to solvent losses and decreased solvent performance. Oxygen (O 2 ) in the flue gas is dissolved into the aqueous solvent and can reactively degrade the amine component. Advanced aqueous amine solvents are designed to contain additional surfactant and anti-foam additives as well as two types of corrosion inhibitors. These additives contribute to improve the solvent performance while reducing foaming and corrosion of expensive equipment. This work examines the impact of these additives on oxygen solubility (or dissolved oxygen - DO) in various aqueous amines used in PCCC including ethanolamine (MEA), 1-amino-2-propanol (A2P), 2-amino-1-propanol (2A1P), 2-(methylamino)-ethanol (NMEA), 2-(ethylamine)-ethanol (2EAE), diethanolamine (DEA), methyl-diethanolamine (MDEA), dimethylethanolamine (DMEA), piperazine (PZ), 1,2-ethyldiamine (EDA), and 1,6 hexadiamine (HDA). Further, the impact of carbon loading on oxygen solubility with and without these additives was also examined. The surfactant and anti-foam additives had minimal impact on DO for all the solvents investigated. The two anticorrosion additives had opposite effects in the measured DO, 2- mercaptobenzothiazole (MBT) decreased the DO concentration, and sodium metavanadate showed an increase. These results indicate that several of these common additives can be expected to minimally affect DO related oxidative degradation in these advance amine solvents.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

Isotherm modeling and techno-economic analysis of a TSA moving bed process using a tetraamine-appended MOF for NGCC applications

Tetraamine-appended metal-organic frameworks (MOF) are a new family of amine-functionalized MOF materials that show potential for CO 2 capture from flue gas conditions relevant to natural gas combined cycle (NGCC) power plants. This work presents isotherm modeling of the tetraamine-appended MOF Mg 2 (dobpdc)(3-4-3)(dobpdc 4- =4,4'-dioxidobiphenyl-3,3'dicarboxylate;3-4-3=N,N'bis(3-aminopropyl)-1,4-diaminobutane), process modeling, scale up, and a techno-economic optimization of a moving bed Temperature Swing Adsorption (TSA) process for carbon capture using this sorbent. This MOF exhibits a unique two-step CO 2 adsorption profile in three different pressure ranges. Thus, arctangent-based logistic functions and, quadratic and Langmuir models were employed to represent such isotherm behavior. The results of the isotherm model show good fitting vs the experimental data with an RMSE of 0.41. Here, to model the carbon capture process, the isotherm model was embedded into a moving bed contactor model, and this was used to simulate a TSA CO 2 capture cycle and evaluate cost-optimal designs considering flue gas from a -650 MWe NGCC power plant. The capital cost model consists of CAPEX correlations for reactors, compressors, ducting, etc., while the operating costs include steam, water, chemicals, and electricity (following NETL's quality guidelines for energy systems studies). A techno-economic optimization of the capture system was performed by using NETL's Framework for the Optimization and Quantification of Uncertainty and Surrogates tool (FOQUS). Results suggest that a moving bed carbon capture system with tetraamine-appended MOF can be competitive compared to conventional MEA solvent-based capture processes for NGCC plants, when a heat recovery efficiency of at least 40% is achieved, and MOF materials can be produced at a cost below -$9/kg.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A review of functions, attributes, properties and measurements for the quality control of proton exchange membrane fuel cell components

Quality control (QC) is an essential part of fuel cell technology industrialization, providing means to reduce cost of components, enhancing the reliability of the final product, and offering specification guidance for new entrants in the supply chain. The membrane electrode assembly (MEA), including membrane, catalyst layer (CL), and gas diffusion layer (GDL), as well as bipolar plate (BP), are key components of a proton exchange membrane (PEM) fuel cell, and the attributes of each component strongly correlate with the cell performance and longevity. To ensure the quality of the fuel cell, it is of great importance to characterize the properties with respect to the standardization of component/sub-component specifications. In collaboration with the fuel cell industry, this work aims at establishing compendiums of attributes, or so-called books of attributes, of key fuel cell components for the QC of PEM fuel cells through reviewing, identifying, categorizing, and prioritizing the main attributes/properties that determine their functionalities. The books of attributes for the major PEM fuel cell components include catalyst coated membrane (CCM) as a sub-assembly, GDL, and BP. To address the full spectrum of fuel cell components, gaskets and sub-gaskets are also included.

25 ENERGY STORAGE↗
DOE OSTI2023

The impacts of membrane pinholes on PEM water electrolysis

Polymer electrolyte membrane (PEM) water electrolysis is a promising technology to efficiently produce green hydrogen. Irregularities in membrane electrode assembly (MEA) component materials caused by manufacturing, processing, handling, or operation can lead to performance loss and failure. One example is the presence of pinholes in the membrane, which can cause increased gas transport (crossover) and lead to electrical shorting. This work investigates the effects of intentionally introduced pinholes with various sizes up to 350μm in diameter. The presence of the pinholes resulted in minimal impacts on the cell voltage (±30 mV at 4Acm -2 ). However, the pinholes significantly increased H 2 crossover, which decreased hydrogen production efficiency and increased the minimum current density for safe operation. The impacts of the pinhole on the H 2 crossover and efficiency are more severe for open pinhole features than tear-like pinhole features. In conclusion, this research demonstrates that even small pinholes cannot be disregarded from a safety, efficiency, and operating strategy perspective.

08 HYDROGEN↗
DOE OSTI2024

Impact of polymer additives on crack mitigation of rod-coated fuel cell cathode catalyst layers

Cracks in catalyst layers (CLs) are a potential source of long-term failure in a fuel cell membrane electrode assembly (MEA). While modifications to the CL ink formulation can affect the degree of cracking, these changes may lead to lower initial performance than their cracked analogues due to the established link between formulation and performance. In this work, we explored the use of polymeric additives to mitigate CL cracks. Small quantities of poly (acrylic acid), poly (ethylene oxide), poly (methyl methacrylate), or poly (vinyl alcohol) - 5 wt% relative to ionomer mass - were added to the ink prior to its final mixing. Poly (vinyl alcohol) resulted in crack-free CLs, whereas the other polymers resulted in CLs with similar crack percentages as the control CL. Through a combination of transmission electron microscopy, X-ray computed tomography, and infrared spectroscopy, we ascribed the crack-mitigating mechanism of poly (vinyl alcohol) to its ability to hydrogen-bond with Nafion, the ion conducting polymer binder in the catalyst ink. Initial performance of this non-cracked electrode exhibited nearly identical electrochemical behavior to its cracked counterpart, demonstrating that PVA additives successfully reduce cracks while maintaining cell initial performance.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

Blended conventional and high oxygen permeability ionomers as a fuel cell electrode binder

Ionomer strongly influences the performance of proton exchange membrane fuel cells (PEMFCs), affecting catalyst activity and reactant transport within the electrodes. While recent work on high oxygen permeability ionomers (HOPI) has demonstrated improved performance compared to conventional perfluorosulfonic acid (PFSA) ionomers such as Nafion™, there have also been reports of increased cracking in fabricated electrodes. We investigated the effects of blending HOPI with Nafion™ ionomer dispersions when fabricating cathode catalyst layers (CCLs). Small-angle x-ray scattering suggests that the ionomers mix well, and adsorption measurements indicate that HOPI adsorbs less strongly to the carbon-supported platinum (Pt) catalyst, and in blends, the Nafion™ ionomer exhibits a greater degree of adsorption. Imaging CCLs revealed a decrease in crack formation in blended samples as HOPI content decreased, with 14% HOPI having the lowest crack density. In a membrane electrode assembly (MEA) using a high surface area carbon support, the 14% HOPI blend exhibited similar performance to 100% HOPI. However, similar performance enhancements were not achieved with a medium surface area carbon support. These findings suggest a path for low-crack CCLs with enhanced oxygen transport, while highlighting a need for further investigation of ionomer blending towards efficient and durable PEMFCs.

25 ENERGY STORAGE↗
DOE OSTI2020

Ultra-low radioactivity Kapton and copper-Kapton laminates

Polyimide-based materials, like Kapton, are widely used in flexible cables and circuitry due to their unique electrical and mechanical characteristics. This study is aimed at investigating the radiopurity of Kapton for use in ultralow background, rare-event physics applications by measuring the 238U, 232Th, and natK levels using inductively coupled plasma mass spectrometry. Commercial-off-the-shelf Kapton varieties, mea- sured at approximately 950 and 120 pg/g 238U and 232Th (1.2×104 and 490 µBq/kg), respectively, can be a significant background source for many current and next-generation ultralow background detectors. This study has found that the dominant contamination is due to the use of dicalcium phosphate (DCP), a nonessential slip additive added during manufacturing. Alternative Kapton materials were obtained that did not contain DCP and were determined to be significantly more radiopure than the commercially- available options with 12 and 19 pg/g 238U and 232Th (150 and 77 µBq/kg), respectively. The lowest radioactivity version produced (Kapton ELJ, which contains an adhesive) was found to contain single digit pg/g levels of 238U and 232Th, two-to-three orders of magnitude cleaner than commercial-off-the- shelf options. Moreover, copper-clad polyimide laminates employing Kapton ELJ as the insulator were obtained and measured and showed to be very radiopure at 8.6 and 22 pg/g 238U and 232Th (110 and 89 µBq/kg), respectively.

Arnquist, Isaac J.↗
DOE OSTI2022

Regenerable solvents mediate accelerated low temperature CO 2 capture and carbon mineralization of ash and nano-scale calcium carbonate formation

The dual need to remove CO 2 from our emissions and treat alkaline industrial residues such as ash materials motivate the design of innovative pathways to simultaneously capture and convert CO 2 into mineralized carbonates. Direct carbon mineralization is one approach that addresses the need to simultaneously treat alkaline industrial residues and mineralize CO 2 emissions. Low CO 2 solubility in water and slow kinetics at ambient temperature have challenged the direct carbon mineralization of alkaline industrial residues. Here, to address these challenges, the use of CO 2 capture solvents that enhance CO 2 solubility and facilitate accelerated carbon mineralization of fly ash at temperatures below 90 °C is investigated. Calcium carbonate formation results in the inherent regeneration of the solvent. The carbon mineralization extents of non-calcium carbonate content in fly ash were 50% and 51% and in waste ash were 58% and 62% in 2.5 M sodium glycinate and 30 wt% MEA solutions, respectively. The experiments were performed at 50 °C for 3 hours with CO 2 partial pressure of 1 atm in a continuously stirred slurry environment with 15 wt.% solid. Furthermore, nanoscale CaCO 3 is successfully synthesized from dissolved calcium using CO 2 -loaded sodium glycinate and surfactants such as CTAB (Cetyl Trimethyl Ammonium Bromide). Surfactants such as CTAB bind to the calcium carbonate surface and regulate the growth of calcium carbonate particles. These innovative approaches demonstrate the feasibility of directly storing CO 2 in fly ash and waste ash as calcium carbonate and producing nanoscale calcium carbonate using regenerable CO 2 capture solvents.

42 ENGINEERING↗
DOE OSTI2024

Pronounced reduction in the regeneration energy of potassium sarcosinate CO 2 capture solvent using TiO 2

Absorption-based CO 2 capture technologies face economic feasibility concerns due to the exceedingly high energy requirements of solvent regeneration. Among various proposed solutions, solid acid-aided solvent regeneration stands out as a promising approach. Studies have shown that solid materials containing Lewis and Brønsted acid sites can facilitate deprotonation of protonated amine and breakdown of carbamate molecules, which significantly increases CO 2 desorption rate and decreases regeneration energy of common solvents such as MEA and DEA. However, the influence of solid acids on alternate solvents such as amino acids is not well known. Here, we report the performance of TiO 2 for the regeneration of CO 2 -loaded aqueous potassium sarcosinate (K-Sar) solvent. K-Sar is an environmentally friendly amino-acid salt that provides high CO 2 absorption rates, making it a good candidate for both point-source and direct-air capture. TiO 2 is hydrothermally stable and contains high surface acid site concentration. Desorption of CO 2 from K-Sar starts at room temperature in the presence of TiO 2 , while such onset temperature is greater than 70°C for regeneration without TiO 2 . Further, at a temperature of 95°C, the maximum CO 2 desorption rate and cumulative CO 2 removal increase by 128% and 91%, respectively, in the presence of TiO 2 compared to the no TiO 2 case. The total regeneration energy could be reduced by ~ 50% with TiO 2 , showcasing the significant role this process can take in improving the commercial competitiveness of absorption-based CO 2 capture. Further characterization with XRD, SEM, and NMR concluded that neither the TiO 2 powder nor the solvent undergoes any physical or chemical degradation in the regeneration process, suggesting the potential of their long-term usability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Electrolyzers in focus: advances in CO 2 electrolyzer designs

Electrochemical CO 2 reduction (ECR) remains a viable method to reintegrate anthropogenic CO 2 into current energy infrastructures through its conversion into commodity chemicals. To facilitate the integration of ECR, electrochemical devices called electrolyzers must be implemented to overcome the inherent limitations that exist in current ECR experiments, namely kinetics and mass transport. In this review, we outline the current and advancing designs in ECR electrolyzers, with a focus on the following five electrochemical devices: membrane electrode assemblies (MEA), flow cell (FC), rotating disk electrode (RDE), rotating ring-disk electrode (RRDE), and rotating cylinder electrode (RCE). We highlight the tunable components of each electrolyzer with a forward outlook on the optimization and relevance of electrolyzer designs in upcoming ECR applications.

CO2 reduction↗
DOE OSTI2022

PGM-Free Oxygen-Reduction Catalyst Development for Proton-Exchange Membrane Fuel Cells: Challenges, Solutions, and Promises

Proton-exchange membrane fuel cells (PEMFCs) are efficient and clean hydrogen energy technologies for transportation and stationary applications. Highly active and durable low-cost cathode catalysts for the oxygen-reduction reaction (ORR) under challenging acidic environments are desperately needed to address the cost and durability issues of PEMFCs. The most promising platinum group metal (PGM)-free catalysts for the ORR in acidic media are atomically dispersed and nitrogen-coordinated metal site catalysts denoted as M–N–C, M = Fe, Co, or Mn. Due to significant efforts in the past few decades, these catalysts have demonstrated much-improved ORR activity and promising initial fuel cell performance approaching traditional Pt/C catalysts. However, the insufficient long-term stability (up to 5000 h) under PEMFC operation represents a primary technical barrier to making current PGM-free catalysts less viable yet in PEMFCs. In this Account, we highlight recent advances in synthesizing efficient PGM-free catalysts for the ORR in PEMFCs, emphasizing effective strategies to improve mass and intrinsic activity and the possible degradation mechanisms. In particular, a chemical doping method based on the zeolitic imidazolate framework (ZIF)-8 represents the key to developing efficient M–N–C catalysts containing atomically dispersed and nitrogen-coordinated single metal active sites (i.e., MN 4 ). The newly acquired understanding of the formation mechanism of MN 4 active sites during the thermal activation and its correlation to catalytic properties guide the rational catalyst design rather than relying on current trial-and-error approaches. Considerable efforts have further been invested in increasing the active site density and enhancing intrinsic activity by regulating carbon-phase structures and the local coordination environment. Furthermore, these highly active catalysts usually suffer from significant activity loss during the ORR. Therefore, breaking the activity–stability trade-off is the key to simultaneously achieving activity and stability in one catalyst, which is discussed on the basis of our recent successes in regulating local carbon structures surrounding active single metal sites. Significant research efforts toward understanding the degradation mechanisms and improving the lifetime of PGM-free catalysts are still crucial for viable applications in the future. Novel electrode designing strategies are needed to translate the PGM-free catalysts’ ORR activity to solid-state electrolyte-based membrane electrode assemblies (MEAs) with robust three-phase (i.e., gas–liquid–solid) interfaces for efficient charge and mass transports for performance improvement. On the basis of our effort at the University at Buffalo supported by ElectroCat Consortium associated with U.S. DOE’s Hydrogen and Fuel Cell Technologies Office, we provide a perspective on PGM-free cathode catalysts concerning remaining bottlenecks and future opportunities, aiming to inspire the community in both mechanistic understanding and technological development.

08 HYDROGEN↗
DOE OSTI2022

Electrocatalysis in Alkaline Media and Alkaline Membrane-Based Energy Technologies

Hydrogen energy-based electrochemical energy conversion technologies offer the promise of enabling a transition of the global energy landscape from fossil fuels to renewable energy. Here, we present a comprehensive review of the fundamentals of electrocatalysis in alkaline media and applications in alkaline-based energy technologies, particularly alkaline fuel cells and water electrolyzers. Anion exchange (alkaline) membrane fuel cells (AEMFCs) enable the use of nonprecious electrocatalysts for the sluggish oxygen reduction reaction (ORR), relative to proton exchange membrane fuel cells (PEMFCs), which require Pt-based electrocatalysts. However, the hydrogen oxidation reaction (HOR) kinetics is significantly slower in alkaline media than in acidic media. Understanding these phenomena requires applying theoretical and experimental methods to unravel molecular-level thermodynamics and kinetics of hydrogen and oxygen electrocatalysis and, particularly, the proton-coupled electron transfer (PCET) process that takes place in a proton-deficient alkaline media. Extensive electrochemical and spectroscopic studies, on single-crystal Pt and metal oxides, have contributed to the development of activity descriptors, as well as the identification of the nature of active sites, and the rate-determining steps of the HOR and ORR. Among these, the structure and reactivity of interfacial water serve as key potential and pH-dependent kinetic factors that are helping elucidate the origins of the HOR and ORR activity differences in acids and bases. Additionally, deliberately modulating and controlling catalyst-support interactions have provided valuable insights for enhancing catalyst accessibility and durability during operation. The design and synthesis of highly conductive and durable alkaline membranes/ionomers have enabled AEMFCs to reach initial performance metrics equal to or higher than those of PEMFCs. We emphasize the importance of using membrane electrode assemblies (MEAs) to integrate the often separately pursued/optimized electrocatalyst/support and membranes/ionomer components. Operando/in situ methods, at multiscales, and ab initio simulations provide a mechanistic understanding of electron, ion, and mass transport at catalyst/ionomer/membrane interfaces and the necessary guidance to achieve fuel cell operation in air over thousands of hours. We hope that this Review will serve as a roadmap for advancing the scientific understanding of the fundamental factors governing electrochemical energy conversion in alkaline media with the ultimate goal of achieving ultralow Pt or precious-metal-free high-performance and durable alkaline fuel cells and related technologies.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Hybrid Absorption–Crystallization Strategies for the Direct Air Capture of CO2 Using Phase-Changing Guanidium Bases: Insights from in Operando X-ray Scattering and Infrared Spectroscopy Measurements

Efforts to limit rising concentrations of CO 2 have motivated the development of negative emission technologies. Direct air capture (DAC) of CO 2 is one of the negative emissions technologies that has been proposed for the direct removal of CO 2 from the atmosphere. Phase-changing bis(iminonoguanidine) (BIG) sorbents have been developed for the direct air capture of CO 2 . These phase changing sorbents, specifically glyoxal-bis(iminoguanidine) (GBIG), involve (1) CO 2 absorption with aqueous amino acid salts, such as K- or Na-glycinate to yield bicarbonate-rich solutions, (2) crystallization of the bicarbonate anions with a BIG solid, which regenerates the amino acid, and (3) solid-state CO 2 release from the carbonate crystals and BIG regeneration. Despite the promising potential of these materials, their structural evolution during the thermal regeneration of the BIG solids, chemical regeneration of the sodium or potassium glycinate solvents, and the crystallization behavior of CO 2 -loaded BIG bicarbonate remain to be evaluated and understood in detail. The aim of this study is to probe these knowledge gaps. In situ wide-angle X-ray Scattering (WAXS) results show that CO 2 and water molecules in GBIG bicarbonate are simultaneously released in a single step during the thermal regeneration of the sorbent at 97 – 134 °C. In situ ATR-FTIR measurements showed that sodium glycinate and GBIG bicarbonate are simultaneously generated when GBIG, glycine, and sodium bicarbonate are reacted. The crystallization of GBIG bicarbonate from GBIG and CO 2 -loaded monoethanolamine (MEA) occurs rapidly in the first 10 min of the reaction, as determined using in situ GI-SAXS measurements. Overall, the insights from these studies are essential for the scalable implementation of CO 2 capture technologies using these phase-changing sorbents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Design of Experiments for Dynamic Test Runs in Solvent-Based CO 2 Capture Pilot Plants

Test runs in the pilot plants consume significant resources, and therefore, the learning from test runs should be maximized. Test runs conducted in the pilot plants are often steady state. It takes several hours for reaching steady-state in the pilot plants, and thus, the duration of the test runs needs to be long even for collecting few steady-state data points. On the other hand, a large number of measurements can be collected through dynamic test runs in a short span of time. This paper presents a systematic design of dynamic experiments (DoDEs) for identifiability of model parameters, which is achieved by persistently exciting the inputs signals. A pseudorandom binary sequence (PRBS) is designed as the input signal for DoDE due to its efficiency in obtaining sufficient spectral content. However, due to the long sequence size of the PRBS signal, a Schroeder-phase input signal, which is a multisine signal, is also designed. Tests for both types of signals are run in the Pilot Solvent Test Unit (PSTU) at the National Carbon Capture Center in Wilsonville, Alabama. The transient data are used to solve dynamic data reconciliation and parameter estimation problem. The estimated parameters are found to be not only superior to those estimated from using data collected from hundreds of steady-state test runs in a nonreactive (air–water) system, but the parameters could be estimated by using the dynamic data collected for about 24 h from the pilot plant for the MEA-H 2 O–CO 2 system.

CO2 capture↗
DOE OSTI2024

Surface Decoration of Platinum Catalysts by ZrO 2– x Nanoclusters for Durable Fuel Cell Applications

Improving the activity and durability of carbon-supported platinum catalysts for the oxygen-reduction reaction (ORR) in acidic electrolytes is crucial to reducing the high overpotentials and power loss over time in proton-exchange membrane fuel cells (PEMFCs). We found that platinum nanoparticle catalyst deposited on an engineered carbon support in the presence of zirconium enabled higher ORR activity and 25% better retention in electrochemically active surface area (ECSA), thereby improving durability. The use of zirconium precursor in the carbon synthesis process led to the formation of atomically dispersed Zr and ZrO 2 nanoparticles on the support. Upon Pt deposition and subsequent heat treatment, the ZrO 2 particles preferentially rearranged on and around the platinum nanoparticles in a chemically reduced form as zirconium suboxide (ZrO 2-x ) surface-decorated nanoclusters, which mitigated Pt nanoparticle coarsening. Finally, analysis of the here-to-fore unknown catalyst structure as well as its performance and durability in a PEM fuel cell membrane electrode assembly (MEA) is discussed.

25 ENERGY STORAGE↗
DOE OSTI2026

Impact of Interposer Microstructure on Ionic Transport in Liquid-Phase Bicarbonate Electrolysis

The electrochemical reduction of CO 2 (CO 2 RR) is a potentially scalable approach for converting captured carbon dioxide into value-added products. Conventional gas-phase electrolysis systems can suffer from carbonate crossover, which limits the efficiency of the system. Liquid-phase (bi)carbonate electrolysis using bipolar membrane electrode assemblies (BPMMEA) has emerged as a promising alternative. The interposer layer, a porous mass-transport material between the BPM and the catalyst, is an essential component of the MEA, as it allows evolved CO 2 to reach the catalyst surface for reaction. In the absence of this layer, evolved CO 2 generated by the pH swing process at the BPM can be converted back into (bi)carbonate (CO 2 recapture) due to the high bulk pH. Thus, clear design guidelines are needed to maximize CO 2 conversion, minimize CO 2 recapture in the catholyte, and improve energy efficiency. Here, the transport properties of the interposer are systematically characterized by X-ray tomography and symmetric-cell impedance spectroscopy to quantify porosity, tortuosity, and the resulting MacMullin number. We then examine the correlation between these material properties and the electrolyzer performance. We focus on characterizing two commercial porous membrane filters, mixed cellulose ester (MCE) and poly(ether sulfone) (PES).

CO2 electrolysis↗