Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Microstructural evaluation of NiTi-based films deposited by magnetron sputtering

Shape memory alloy films belonging to the NiTi-based systems were deposited on heated and unheated substrates, by magnetron sputtering in a custom made system, and their structure and composition was analyzed using electron microscopy. Several substrates were used for the depositions: glass, Cu-Zn-Al, Cu-Al-Ni and Ti-NiCu shape memory alloy ribbons and kapton. The composition of the Ti-Ni-Cu films showed limited differences, compared to the one of the target and the microstructure for the DC magnetron sputtering revealed crystallized structure with features determined on peel off samples from a Si wafer. Both inter and transcrystalline fractures were observed and related to the interfacial stress developed on cooling from deposition temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Resistive switching behavior of RF magnetron sputtered ZnO thin films

The resistive switching characteristics of RF magnetron sputtered zinc oxide thin films have been studied. The x-ray diffraction studies confirm the formation of crystalline ZnO on Pt/TiO{sub 2}/SiO{sub x}/Si substrate. We have fabricated Cu/ZnO/Pt device using a shadow masking technique for resistive switching study. Our Cu/ZnO/Pt device exhibits a unipolar resistive switching behaviour. The switching observed in our device could be related to oxygen vacancies or Cu ions that generate the conducting filaments responsible for resistive switching. We found HRS to LRS resistance ratio of as high as ∼200 for our Cu/ZnO/Pt device. The higher resistance ratio and stability of Cu/ZnO/Pt device would make our RF magnetron sputtered zinc oxide thin films suitable for non volatile memory applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of nitrogen ion implantation time on tungsten films deposited by DC magnetron sputtering on AISI 410 martensitic stainless steel

Nitrogen ion implantation time on tungsten thin film deposited on surface of AISI 410 steel has been performed. Tungsten thin film produced by dc magnetron sputtering method was deposited on AISI 410 martensitic stainless steel substrates, and then the nitrogen ions were implanted on tungsten thin film. The objective of this research is to investigate the effects of implantation deposition time on surface roughness, microhardness, specific wear and corrosion rate of nitrogen implanted on tungsten film. Magnetron sputtering process was performed by using plasma gas of argon (Ar) to bombardier tungsten target (W) in a vacuum chamber with a pressure of 7.6 x 10{sup −2} torr, a voltage of 300 V, a sputter current of 80 mA for sputtered time of 10 minutes. Nitrogen implantation on tungsten film was done with an initial pressure of 3x10{sup −6} mbar, a fluence of 2 x 10{sup 17} ions/cm{sup 2}, an energy of 100 keV and implantation deposition times of 0, 20, 30 and 40 minutes. The surface roughness, microhardness, specific wear and corrosion rate of the films were evaluated by surfcorder test, Vickers microhardness test, wear test and potentiostat (galvanostat) test respectively. The results show that the nitrogen ions implanted deposition time on tungsten film can modify the surface roughness, microhardness, specific wear and corrosion rate. The minimum surface roughness, specific wear and corrosion rate can be obtained for implantation time of 20 minutes and the maximum microhardness of the film is 329 VHN (Vickers Hardness Number) for implantation time of 30 minutes. The specific wear and corrosion rate of the film depend directly on the surface roughness.

36 MATERIALS SCIENCE↗

High-rate magnetron sputter deposition of low-stress boron carbide films on tilted substrates

Boron carbide is attractive for several applications, including nuclear fuel capsules for inertial confinement fusion (ICF). The fabrication of ICF capsules involves the deposition of ultrathick coatings with density and thickness uniformity on submicron length scales on non-planar (spherical) substrates. Such a deposition requires control of the deposition rate, residual stress, and film microstructure. Here, we systematically study the direct-current magnetron sputter deposition of B 4 C coatings with a full-face-erosion magnetron source as a function of substrate tilt and Ar working gas pressure. Film properties are correlated with results of plasma diagnostics and predictions of Monte Carlo simulations of ballistic sputtering and gas-phase transport. The fabrication of low-stress amorphous B 4 C films with deposition rates of 7μm/h is demonstrated.

Kawasaki, K. [Lawrence Livermore National Laborato↗

Progress in Developing Novel Double-Shell Metal Targets Via Magnetron Sputtering

Double shell inertial confinement fusion targets represent a unique platform for achieving ignition. They consist of a low-Z outer ablator, a high-Z inner pusher layer, and low density foam layer sandwiched in-between. There is the possibility that double shell targets may achieve ignition at lower ion temperatures due to the containment of radiation and conduction losses as well as requiring smaller convergence ratios. We have explored using magnetron sputtering to make the inner high-Z pusher layers and have demonstrated a W-Cr bilayer inner shell design. An Al-Be mixture was explored as one of the outer ablator materials. This material takes advantage of Al x-ray M-band absorption to reduce pre-heating and still retain Be high ablation speeds. Typical commercial Al-Be materials suffer from phase separation. However, by using magnetron sputtering we have been able to demonstrate homogeneous Al-Be ablator coatings. The sputtered material forms with nano-sized grains and has demonstrated excellent machinability. As a second type of shell explored, pushered single shells can exploit large density gradients to stabilize Rayleigh-Taylor instabilities during compression. Sharp gradients will have higher ignition yields and larger grading lengths will be more stable. We were able to demonstrate pushered single shells made from W-Be gradient layers with various grading slopes and provide simulated results showing that the grading profiles can be influenced by the coating rates of two components.

36 MATERIALS SCIENCE↗

Electron dynamics in radio frequency magnetron sputtering argon discharges with a dielectric target

Abstract We demonstrate a self-consistent and complete description of electron dynamics in a typical electropositive radio frequency magnetron sputtering (RFMS) argon discharge with a dielectric target. The electron dynamics, including the electron power absorption dynamics in one radio frequency (RF) period, is studied via a fully kinetic 2d3v particle-in-cell/Monte Carlo collision (PIC/MCC) electrostatic simulation. The interplay between the fundamental plasma parameters is analyzed through their spatiotemporal dynamics. Due to the influence of magnetic trap on the electron transport, a spatially dependent charging that perturbs the electric potential is observed on the dielectric target surface, resulting in a spatially dependent ion energy distribution along the target surface. The E × B drift-to-discharge current ratio is in approximate agreement with Bohm diffusion. The electron power absorption can be primarily decoupled into the positive Ohmic power absorption in the bulk plasma region and the negative pressure-induced power absorption near the target surface. Ohmic power absorption is the dominant electron power absorption mechanism, mostly contributed by the azimuthal electron current. The power absorption due to electron inertial effects is negligible on time-average. Both the maximum power absorption and dissipation of electrons appear in the bulk plasma region during the second half of the RF period, implying a strong electron trapping in magnetron discharges. The contribution of secondary electrons is negligible under typical RFMS discharge conditions.

Physics↗

Thermal stability and tribological properties of CrZr-Si-N films synthesized by closed field unbalanced magnetron sputtering

In this work, CrZr-Si-N films with various Si contents ({<=}6.4 at. %) were synthesized by closed field unbalanced magnetron sputtering with vertical magnetron sources. The characteristics such as hardness, surface morphology, and friction coefficient of the films as a function of the Si content after annealing up to 500 degree sign C in air were evaluated. Results revealed that the as-deposited films showed very similar characteristics irrespective of the Si content. However, after annealing at 500 degree sign C, the film characteristics showed a strong dependency upon the Si content. After annealing at 500 degree sign C, the hardness of the Cr{sub 39.4}Zr{sub 12.3}N{sub 48.3} film decreased significantly to approximately 24 GPa and the surface roughness value increased approximately 3.5 times more than that of the as-deposited film. The Cr{sub 34.6}Zr{sub 10.6}-Si{sub 6.4}-N{sub 48.4} film, however, was observed to have a hardness of approximately 30 GPa, which is close to that of the as-deposited film, 32 GPa. In addition, as the wear test temperature increased from room temperature to 500 degree sign C, the average friction coefficient of the Cr{sub 39.4}Zr{sub 12.3}N{sub 48.3} film increased significantly from approximately 0.23 to 0.81, but the average friction coefficient of the Cr{sub 34.6}Zr{sub 10.6}-Si{sub 6.4}-N{sub 48.4} film was not changed extensively, measuring approximately 0.43. These results could be attributed to the improvement of the thermal stability by adding Si into the Cr-Zr-N films.

36 MATERIALS SCIENCE↗

Rotation magnet sputtering: Damage-free novel magnetron sputtering using rotating helical magnet with very high target utilization

Novel magnetron-sputtering equipment, called rotation magnet sputtering (ROT-MS), was developed to overcome various disadvantages of current magnetron-sputtering equipment. Disadvantages include (1) very low target utilization of less than 20%, (2) difficulty in obtaining uniform deposition on the substrate, and (3) charge-up damages and ion-bombardment-induced damages resulting from very high electron temperature (>3 eV) and that the substrate is set at the plasma excitation region. In ROT-MS, a number of moving high-density plasma loops are excited on the target surface by rotating helical magnets, resulting in very high target utilization with uniform target erosion and uniform deposition on the substrate. This excellent performance can be principally maintained even if equipment size increases for very large-substrate deposition. Because strong horizontal magnetic fields (>0.05 T) are produced within a very limited region just at the target surface, very low electron-temperature plasmas (<2.5 eV for Ar plasma and <1 eV for direct-current-excited Xe plasma) are excited at the very limited region adjacent to the target surface with a combination of grounded plate closely mounted on the strong magnetic field region. Consequently, the authors can establish charge-up damage-free and ion-bombardment-induced damage-free processes. ROT-MS has been applied for thin-film formation of LaB{sub 6}, which is well known as a stable, low-work-function bulk-crystal material for electron emissions. The work function of the LaB{sub 6} film decreased to 2.8 eV due to enhanced (100)-orientation crystallinity and reduced resistivity realized by adjusting the flux of low-energy bombarding ions impinging on the depositing surface, which work very efficiently, improving the performance of the electron emission devices.

36 MATERIALS SCIENCE↗

Radio-frequency magnetron sputter deposition of ultrathick boron carbide films

The deposition of thick B 4 C films with low residual stress by conventional direct-current magnetron sputtering is accompanied by the formation of dust particulates contaminating the target, chamber, and substrates and leading to the formation of nodular defects in films. Here, we demonstrate that the formation of particulates is greatly reduced during radio-frequency magnetron sputtering (RFMS). We systematically study properties of B 4 C films deposited by RFMS with a substrate temperature of 330 °C, a target-to-substrate distance of 10 cm, Ar working gas pressure in the range of 4.5–12.0 mTorr (0.6–1.6 Pa), and substrate tilt angles of 0°–80°. All films are x-ray amorphous. A columnar structure develops with increasing either Ar pressure or substrate tilt. For columnar films, the column tilt angle decreases with increasing Ar pressure, which we attribute to a corresponding increase in the width of the distribution of impact angles of deposition flux. In contrast to the Keller–Simmons rule, the deposition rate increases with increasing Ar pressure, which suggests a better coupling of the RF energy to the plasma processes that lead to target sputtering at higher pressures. There is a critical substrate tilt angle above which the total residual stress is close to zero. This critical substrate tilt angle is ~0° for an Ar pressure of 12 mTorr (1.6 Pa). The lower residual stress state, necessary for depositing ultrathick films, is characterized by a larger concentration of nanoscale inhomogeneities and decreased mechanical properties. Based on these results, RFMS deposition of 60-μm-thick B 4 C films is demonstrated.

36 MATERIALS SCIENCE↗

Orbital motion of dust particles in an rf magnetron discharge. Ion drag force or neutral atom wind force

Microparticles with sizes up to 130 {mu}m have been confined and the velocity and diameter of particles in a plasma trap of an rf magnetron discharge with an arc magnetic field have been simultaneously measured. The motion of the gas induced by electron and ion cyclotron currents has been numerically simulated using the Navier-Stokes equation. The experimental and numerical results confirm the mechanism of the orbital motion of dust particles in the magnetron discharge plasma that is associated with the orbital motion of the neutral gas accelerated by electron and ion drift flows in crossed electric and magnetic fields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Nanoscale Cu{sub 2}O films: Radio-frequency magnetron sputtering and structural and optical studies

Nanoscale copper (I) oxide layers are formed by magnetron-assisted sputtering onto glassy and silicon substrates in an oxygen-free environment at room temperature, and the structural and optical properties of the layers are studied. It is shown that copper oxide formed on a silicon substrate exhibits a lower degree of disorder than that formed on a glassy substrate, which is supported by the observation of a higher intensity and a smaller half-width of reflections in the diffraction pattern. The highest intensity of reflections in the diffraction pattern is observed for Cu{sub 2}O films grown on silicon at a magnetron power of 150 W. The absorption and transmittance spectra of these Cu{sub 2}O films are in agreement with the well-known spectra of bulk crystals. In the Raman spectra of the films, phonons inherent in the crystal lattice of cubic Cu{sub 2}O crystals are identified.

36 MATERIALS SCIENCE↗

Lithium nitride coatings deposited by magnetron sputtering on sulfide electrolytes for solid-state batteries

Lithium nitrides have been considered as promising candidates for interfacial layers in solid-state lithium batteries (SSBs). Previously reported lithium nitride (Li 3 N) coatings were mostly prepared by the reaction between lithium metal and nitrogen gas, which makes it challenging for their thickness control and integration in SSBs. In this study, we prepare Li 3 N via magnetron sputtering for the first time, and apply the resulting coating directly on sulfide solid-state electrolyte. A much smaller impedance increase associated with improved cycling performance is observed in lithium metal symmetric cell. These results demonstrate the feasibility of depositing Li 3 N via magnetron sputtering and its application in SSBs.

25 ENERGY STORAGE↗

Anomalous Retrograde Drifts in Obstructed Magnetron Microdischarges: a Consequence of a Field Reversal in the Anode Sheath?

The goal of this project was to carry out experiments at the Plasma Collaborative Research Facility (Princeton Plasma Physics Laboratory) aimed at confirming or refuting the hypothesis that an electric field reversal occurs in the near-anode region of a strongly obstructed planar magnetron microdischarges. Magnetron discharges are magnetized plasmas with E x B field topologies, and variants of such discharges are widely used in materials processing. The topologies are also similar to that of Hall thrusters used in space propulsion. Understanding the structure of these discharges will aid in developing reliable simulations that are intended to facilitate the further development of such technologies, as the field reversals, presumed to be due to strong axial-driven electron transport, provides further insight into transport properties. The possible existence of such a field reversal is hinted at because of the retrograde-propagating (i.e., negative E x B) spokes or gradient-driven drift instabilities seen in the high speed videos and segmented anode probing of the plasma. The presence of this field reversal should be reflected in the ion dynamics, particularly, in an ion drift towards the anode. The proposed experiments to be conducted at the PCRF are to characterize this anode-directed ion drift using state-of-the-art laser-induced fluorescence velocimetry. In particular, we seek to see if the near-anode ion velocity reverses direction when the external circuit is varied to alter the electron current demand imposed at the anode. Such an ion velocity reversal would confirm the mechanism, which is that the highly obstructed (small gapped) discharge produces strong axial gradients in plasma density, driving more electrons towards the anode then that demanded by the external circuit.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Performance Characterization of a Solenoid-type Gas Valve for the H- Magnetron Source at FNAL

The magnetron-style H- ion sources currently in operation at Fermilab use piezoelectric gas valves to function. This kind of gas valve is sensitive to small changes in ambient temperature, which affect the stability and performance of the ion source. This motivates the need to find an alternative way of feeding H2 gas into the source. A solenoid-type gas valve has been characterized in a dedicated off-line test stand to assess the feasibility of its use in the operational ion sources. H- ion beams have been extracted at 35 keV using this valve. In this study, the performance of the solenoid gas valve has been characterized measuring the beam current output of the magnetron source with respect to the voltage and pulse width of the signal applied to the gas valve.

43 PARTICLE ACCELERATORS↗

Recent Operation of the FNAL Magnetron H- Ion Source

This paper will detail changes in the operational paradigm of the Fermi National Accelerator Laboratory (FNAL) magnetron H- ion source due to upgrades in the accelerator system. Prior to November of 2012 the H- ions for High Energy Physics (HEP) experiments were extracted at ~18 keV vertically downward into a 90 degree bending magnet and accelerated through a Cockcroft-Walton accelerating column to 750 keV. Following the upgrade in the fall of 2012 the H- ions are now directly extracted from a magnetron at 35 keV and accelerated to 750 keV by a Radio Frequency Quadrupole (RFQ). This change in extraction energy as well as the orientation of the ion source required not only a redesign of the ion source, but an updated understanding of its operation at these new values. Discussed in detail are the changes to the ion source timing, arc discharge current, hydrogen gas pressure, and cesium delivery system that were needed to maintain consistent operation at >99% uptime for HEP, with an increased ion source lifetime of over 9 months.

43 PARTICLE ACCELERATORS↗

Phase and Frequency Locked Magnetron

Phase and Frequency locked magnetrons have many important uses from phased array ground penetrating radars to SRF sources. We report on the recent progress in making such a magnetron. The ferrite/garnet material has passed bakeout and outgassi ng tests with outgassing rates well below the requirements. The magnetic field requirements for adjusting the frequency by changing the microwave properties of the ferrite/garnet have been determined. The design of the anode structure with ferrites, magne tic shielding, and magnetic bias has been completed for a low power test. We report on the design status. Muons, Inc. has negotiated an contract with a manufacturing firm, L-3 Electron Devices California Tube Laboratory, Inc., to be the Manufacturing Part ner for the commercialization of this technology and support these Phase II efforts.

43 PARTICLE ACCELERATORS↗

Superlattice-Structured Films by Magnetron Sputtering as New Era Electrodes for Advanced Lithium-ion Batteries

Sustaining sound structures in Si-based anodes is extremely challenging because of the high volumetric expansion that occurs upon cycling. To maintain high capacities over cycles, new designs rely on engineering-specific hierarchical geometries and/or optimized composite compositions such that at least one of the multiple elements serves as buffer and/or electron conductive pathways in the electrodes. In this paper, we report an innovative design in which alternating layers of periodic atomic structures involving multiple elements form a new anode material for lithium-ion batteries. In this work, a superlattice-structured amorphous film made using Si, Mo, and Cu is fabricated by a simple and scalable magnetron sputtering process for the first time. This continuous and repetitive superlattice formation along the film thickness provides a homogeneous stress-strain distribution. The Mo-Cu layer in the superlattice acts as an inactive-conductive layer and as a backbone to handle the volume expansion of active Si upon cycling. This nano-functional superlattice approach enables harnessing the high energy density of Si while maintaining its structural stability. As a result, the electrode exhibits high specific capacity and capacity retention even at high cycling rates. The possible use of the film in a full cell is also evaluated by cycling it vs. the LiMn 1.5 Ni 0.5 O 4 cathode. The full cell maintains a stable capacity of about 900 mAh g anode -1 over 150 cycles, at ~600 mA g -1 rate. The remarkable performance of this nano-functional superlattice film is found to be promising as anodes for applications that require high energy, long calendar life, and excellent abuse tolerance such as electric vehicle batteries.

25 ENERGY STORAGE↗

Probing layered structure of Inconel 625 coatings prepared by magnetron sputtering

Coating/substrate interface and oxide layers present in Inconel 625 film may cause significant impacts on its corrosion behavior. However, layered structure of Inconel 625 coatings remains poorly understood due to its requirement of high spatial resolution. Here we have applied X-ray reflectometry (XRR) to probe the layered structure of magnetron-sputtered Inconel 625 film with atomic spatial resolution. Our results indicate that there exists a 2 nm thick Cr-rich Inconel sublayer underneath the principal film. On top of the principal film, it is found a 2 nm thick oxide layer mainly consisting of NiO. In addition, we detected ~2 Å contamination layer on the sapphire substrate, although argon ion sputter cleaning had been applied to the substrate prior to deposition. By comparing the coatings with different deposition time, we observed that the thickness of principal Inconel 625 layer grows linearly with deposition time, with all other layers remaining constant. Our findings provide insight into the layered structures of Inconel 625 coatings with atomic-scale spatial resolution, and provide directions for future efforts that aim to improve the corrosion resistance of Inconel 625 coatings.

14 SOLAR ENERGY↗