Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Physical properties of epitaxial ZrN/MgO(001) layers grown by reactive magnetron sputtering

Single-crystal ZrN films, 830 nm thick, are grown on MgO(001) at 450 °C by magnetically unbalanced reactive magnetron sputtering. The combination of high-resolution x-ray diffraction reciprocal lattice maps, high-resolution cross-sectional transmission electron microscopy, and selected-area electron diffraction shows that ZrN grows epitaxially on MgO(001) with a cube-on-cube orientational relationship, (001){sub ZrN}‖(001){sub MgO} and [100]{sub ZrN}‖[100]{sub MgO}. The layers are essentially fully relaxed with a lattice parameter of 0.4575 nm, in good agreement with reported results for bulk ZrN crystals. X-ray reflectivity results reveal that the films are completely dense with smooth surfaces (roughness = 1.3 nm, consistent with atomic-force microscopy analyses). Based on temperature-dependent electronic transport measurements, epitaxial ZrN/MgO(001) layers have a room-temperature resistivity ρ{sub 300K} of 12.0 μΩ-cm, a temperature coefficient of resistivity between 100 and 300 K of 5.6 × 10{sup −8}Ω-cm K{sup −1}, a residual resistivity ρ{sub o} below 30 K of 0.78 μΩ-cm (corresponding to a residual resistivity ratio ρ{sub 300Κ}/ρ{sub 15K} = 15), and the layers exhibit a superconducting transition temperature of 10.4 K. The relatively high residual resistivity ratio, combined with long in-plane and out-of-plane x-ray coherence lengths, ξ{sub ‖} = 18 nm and ξ{sub ⊥} = 161 nm, indicates high crystalline quality with low mosaicity. The reflectance of ZrN(001), as determined by variable-angle spectroscopic ellipsometry, decreases slowly from 95% at 1 eV to 90% at 2 eV with a reflectance edge at 3.04 eV. Interband transitions dominate the dielectric response above 2 eV. The ZrN(001) nanoindentation hardness and modulus are 22.7 ± 1.7 and 450 ± 25 GPa.

36 MATERIALS SCIENCE↗

High-Power Impulse Magnetron Sputter Deposition of Ultrathick Amorphous Carbon

Diamond-like carbon (DLC) is a material of interest for inertial confinement fusion (ICF) ablators. However, the deposition of ultrathick DLC coatings, as required for ICF ablator fabrication, remains a challenge. Here, in this study, we use high-power impulse magnetron sputtering to deposit DLC and demonstrate a set of process parameters leading to high-purity, amorphous DLC coatings with a low compressive residual stress of <400 MPa. Coatings with thicknesses of up to 80 μm are demonstrated.

amorphous carbon↗

Oblique angle deposition of boron carbide films by magnetron sputtering

Many applications of boron carbide (B4C) films entail deposition on non-planar substrates, necessitating a better understanding of oblique angle deposition phenomena. Here, we systematically study the effect of substrate tilt on properties of B 4 C films with thicknesses up to 10 μm deposited by direct current magnetron sputtering. Results show that all films are amorphous and columnar with an average column width of ~100 nm, independent of substrate tilt. Column tilt angles are limited to ~20° even for substrate tilt of 80°. Film density, residual stress, and the refractive index weakly (within ≲20%) depend on substrate tilt. Furthermore, oxygen impurities bond preferentially with carbon atoms in inter-columnar regions. Substrate tilt has a major effect on mechanical properties that decrease by ~50%, suggesting weak interconnection between nano-columns. Implications of these observations for the deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗

Gold-tantalum alloy films deposited by high-density-plasma magnetron sputtering

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. Here, we systematically study the effects of substrate tilt (0°–80°) and negative substrate bias (0–100 V) on properties of ≲3-μm-thick films deposited by high-power impulse magnetron sputtering (HiPIMS) from a Au–Ta alloy target (with 80 at. % of Ta). Results reveal that, for all the substrate bias values studied, an increase in substrate tilt leads to a monotonic decrease in film thickness, density, residual compressive stress, and electrical conductivity. Larger substrate bias favors the formation of a body-centered cubic phase, with films exhibiting lower column tilt and higher density, electrical conductivity, and residual compressive stress. Furthermore, these changes are attributed to metal atom ionization effects, based on the lack of correlation with distributions of landing energies and incident angles of depositing species as calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. By varying substrate tilt and bias in HiPIMS deposition, properties of Au–Ta alloy films can be controlled in a very wide range, including residual stress from –2 to +0.5 GPa, density from 12 to 17 g/cm 3 , and the electrical resistivity from 50 to 4500 μΩ cm, enabling optimum deposition conditions to be selected for specific applications.

36 MATERIALS SCIENCE↗

FePt:C/Fe graded and nongraded films with controllable coercivity fabricated by magnetron sputtering and postannealing

Graded and nongraded FePt:C(hard)/Fe(soft) films with different structures are fabricated by magnetron sputtering and postannealing. Due to the interdiffusion between FePt and C layers during the annealing process, films with a continuous variation in anisotropy are realized by varying the C concentration in the FePt hard layer. In comparison to the FePt/Fe bilayer, the coercivities of graded and nongraded films are effectively reduced. However, the mechanisms of reduction are different. Moreover, adding a nonmagnetic C layer not only tailors the gradient of anisotropy, but also weakens the intergranular exchange interaction.

36 MATERIALS SCIENCE↗

Highly phosphorus-doped crystalline Si layers grown by pulse-magnetron sputter deposition

The electrical properties of highly phosphorus-doped crystalline silicon films deposited by pulse-magnetron sputtering were studied. The films were grown, 450 nm thick, on Si(100) and Si(111) wafers at low substrate temperatures T{sub s} of 450-550 deg. C and post-treated by rapid thermal annealing (RTA) and plasma hydrogenation (PH). In the case of films grown on Si(100), at all values of T{sub s} postgrowth treatment by RTA resulted in an increase in the dopant activation up to 100% and of the Hall mobility to about bulklike values of 50 cm{sup 2} V{sup -1} s{sup -1}. This result suggests high structural quality of the films on Si(100). The Si(111) films, which are typically more defective, exhibit a completely different behavior with a strong dependence of the electrical dopant activation and the Hall mobility on T{sub s}. By post-treatment a maximum P donor activation level of 22% could be obtained. The variation in the post-treatment procedure (RTA+PH and PH+RTA) for the films deposited at high T{sub s} showed that PH results only in minor changes in the film properties. The different influence of RTA and PH is discussed in terms of the different defect structure of the films. These investigations reveal that high T{sub s} and after-treatment by RTA are the main preconditions for optimal electrical film properties.

36 MATERIALS SCIENCE↗

Evolution of the plasma composition of a high power impulse magnetron sputtering system studied with a time-of-flight spectrometer

The plasma of a high power impulse magnetron sputtering system has been investigated using a time-of-flight spectrometer. The target materials included high sputter yield materials (Cu, Ag), transition metals (Nb, Cr, Ti), and carbon (graphite); the sputtering gases were argon, krypton, and nitrogen, and two different target thicknesses were selected to consider the role of the magnetic field strength. Measurements for selected combinations of those parameters give quantitative information on the transition from gas-dominated to metal-dominated (self-sputtering) plasma, on the fractions of ion charge states, and in the case of molecular gases, on the fraction of atomic and molecular ions.

36 MATERIALS SCIENCE↗

Properties of silicon homojunctions with pulse-magnetron sputtered crystalline n{sup +}-emitter layers

Highly phosphorus doped crystalline silicon films were grown by pulse-magnetron sputter deposition on (100) and (111) oriented silicon wafer substrates at low temperatures of 450-550 deg. C. Rapid thermal annealing (RTA) and plasma hydrogenation (PH) were applied as postgrowth treatments. To explore the nature of the junction transport processes the I-V characteristics were studied in different device geometries as a function of temperature. The analysis suggests that depending on the substrate orientation (hkl) both postgrowth treatments influence the bulk-related current component J{sub 0b}{sup (hkl)} of the saturation current density in different manners and introduce additional conduction paths at the perimeter of the measured diode structures. For diodes grown on Si(100) postgrowth treatment by RTA results in a decrease in J{sub 0b}{sup (100)} to respectable 4x10{sup -11} A cm{sup -2}, whereas no major influence of RTA for the Si(111) based junctions could be obtained. They prove to be sensitive to PH post-treatment, which resulted in a reduction in J{sub 0b}{sup (111)} to 8x10{sup -11} A cm{sup -2}. The perimeter induced excess current is most strongly pronounced for the hydrogenated diodes on Si(111) and much less relevant for the RTA treated Si(100) structures.

36 MATERIALS SCIENCE↗

Current-voltage-time characteristics of the reactive Ar/N{sub 2} high power impulse magnetron sputtering discharge

The discharge current and voltage waveforms have been measured in a reactive high power impulse magnetron sputtering (HiPIMS) Ar/N{sub 2} discharge with a Ti target for 400 {mu}s long pulses. We observe that the current waveform in the reactive Ar/N{sub 2} HiPIMS discharge is highly dependent on the pulse repetition frequency, unlike the non-reactive Ar discharge. The current is found to increase significantly as the frequency is lowered. This is attributed to an increase in the secondary electron emission yield during the self-sputtering phase, when the nitride forms on the target at low frequencies. In addition, self-sputtering runaway occurs at lower discharge voltages when nitrogen is added to the discharge. This illustrates the crucial role of self-sputtering in the behavior of the reactive HiPIMS discharge.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of vanadium incorporation on the microstructure, mechanical and tribological properties of Nb–V–Si–N films deposited by reactive magnetron sputtering

Composite Nb–V–Si–N films with various V contents (3.7–13.2 at.%) were deposited by reactive magnetron sputtering and the effects of V content on the microstructure, mechanical and tribological properties of Nb–V–Si–N films were investigated. The results revealed that a three-phase structure, consisting of face-centered cubic (fcc) Nb–V–Si–N, hexagonal close-packed (hcp) Nb–V–Si–N and amorphous Si{sub 3}N{sub 4}, co-exists in the Nb–V–Si–N films and the cubic phase is dominant. The hardness and critical load (L{sub c}) of Nb–V–Si–N films initially increased gradually and reached a summit, then decreased with the increasing V content in the films and the maximum values were 35 GPa and 9.8 N, respectively, at 6.4 at.% V. The combination of V into Nb–Si–N film led to the fracture toughness linearly increasing from 1.11 MPa·m{sup 1/2} at 3.7 at.% V to 1.67 MPa·m{sup 1/2} at 13.2 at.% V. At room temperature (RT), the average friction coefficient decreased from 0.80 at 3.7 at.% V to 0.55 at 13.2 at.% V for the Nb–V–Si–N films. The wear rate of Nb–V–Si–N films initially decreased and then increased after reaching a minimum value of about 6.35 × 10{sup −} {sup 7} mm{sup 3}/N·mm at 6.4 at.% V. As the rise of testing temperature from 200 °C to 600 °C, the average friction coefficient of Nb–V–Si–N films decreased with the increase of the testing temperature regardless of V content. However, the wear rate gradually increased for all films. The average friction coefficient and wear rate at RT and elevated temperatures were mainly influenced by the vanadium oxides with weakly bonded lattice planes. - Highlight: • Fcc-Nb–V–Si–N, hcp-Nb–V–Si–N and amorphous Si{sub 3}N{sub 4} co-existed in the films. • The amount of Si{sub 3}N{sub 4} decreased with increasing V content in the films. • Hardness of Nb–V–Si–N film (6.4 at.%) reached a maximum value of 35 GPa. • Addition of V led to the increase of fracture toughness. • Tribological properties were influenced by lubricant wear debris.

36 MATERIALS SCIENCE↗

Optical properties of ITO films obtained by high-frequency magnetron sputtering with accompanying ion treatment

A variation in the properties of indium-tin-oxide (ITO) films obtained by the method of reactive magnetron sputtering with simultaneous ion treatment is reported. The ITO films feature the following parameters in the optical range of 450-1100 nm: a transmission coefficient of 80%, band gap of 3.50-3.60 eV, and a refractive index of 1.97-2.06. All characteristics of the films depend on the ion-treatment current. The latter, during the course of deposition, reduces the resistivity of the ITO films with the smallest value of the resistivity being equal to 2 Multiplication-Sign 10{sup -3} {Omega} cm. The degradation of films with a high resistivity when kept in air is observed.

36 MATERIALS SCIENCE↗

Growth and characterization of a-axis oriented Cr-doped AlN films by DC magnetron sputtering

Wurtzite type Cr-doped AlN thin films were grown on Si (100) substrates using DC reactive magnetron sputtering with a function of N{sub 2} concentration (15 to 25%). Evolution of crystal structure of these films was studied by GIXRD where a-axis preferred orientation was observed. The electronic binding energy and concentration of Cr in these films were estimated by X-ray photoemission spectroscopy (XPS). We have observed indentation hardness (H{sub IT}) of around 28.2 GPa for a nitrogen concentration of 25%.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of pulse frequency on the ion fluxes during pulsed dc magnetron sputtering

The ion fluxes and energies which impinge on the substrate during the deposition of chromium nitride by asymmetric bipolar pulsed dc reactive magnetron sputtering have been analyzed using energy resolved mass spectrometry. It has been found that there is a remarkable increase in ion flux at higher pulse frequencies and that the peak ion energy is directly related to the positive voltage overshoot of the target voltage. The magnitude of the metal flux depositing on the substrate is consistent with a 'dead time' of {approx}0.7 {mu}s at the start of the on period. The variation of the ion flux with pulse frequency has been explained by a simple model in which the ion density during the on period has a large peak which is slightly delayed from the large negative voltage overshoot which occurs at the start of the on pulse due to increased ionization at that time. This is consistent with the previously observed phenomena in pulsed sputtering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural-dependent thermal conductivity of aluminium nitride produced by reactive direct current magnetron sputtering

This Letter reports the thermal conductivity of aluminium nitride (AlN) thin-films deposited by reactive DC magnetron sputtering on single-crystal silicon substrates (100) with varying plasma and magnetic conditions achieving different crystalline qualities. The thermal conductivity of the films was measured at room temperature with the transient hot-strip technique for film thicknesses ranging from 100 nm to 4000 nm. The thermal conductivity was found to increase with the thickness depending on the synthesis conditions and film microstructure. The conductivity in the bulk region of the films, so-called intrinsic conductivity, and the boundary resistance were in the range [120-210] W m{sup -1} K{sup -1} and [2-30 Multiplication-Sign 10{sup -9}] K m{sup 2} W{sup -1}, respectively, in good agreement with microstructures analysed by x-ray diffraction, high-resolution-scanning-electron-microscopy, and transmission-electron-microscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Experimental evidence of warm electron populations in magnetron sputtering plasmas

This work report on the results obtained using the Langmuir probe (LP) measurements in high-power dc magnetron sputtering discharges. Data show clear evidence of two electron components, such as warm and bulk electrons, in the sputtering plasma in a magnetic trap. We have also used optical emission spectroscopy diagnostic method along with LP to investigate the plasma production. Data show that there is a presence of low-frequency oscillations in the 2–3 MHz range, which are expected to be generated by high-frequency waves. Analysis also suggests that the warm electrons, in the plasmas, can be formed due to the collisionless Landau damping of the bulk electrons.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High Strength and Deformation Mechanisms of A l0.3 CoCrFeNi High-Entropy Alloy Thin Films Fabricated by Magnetron Sputtering

Recently, high-entropy alloy thin films (HEATFs) with nanocrystalline structures and high hardness were developed by magnetron sputtering technique and have exciting potential to make small structure devices and precision instruments with sizes ranging from nanometers to micrometers. However, the strength and deformation mechanisms are still unclear. In this work, nanocrystalline Al0.3CoCrFeNi HEATFs with a thickness of ~4 μm were prepared. The microstructures of the thin films were comprehensively characterized, and the mechanical properties were systematically studied. It was found that the thin film was smooth, with a roughness of less than 5 nm. The chemical composition of the high entropy alloy thin film was homogeneous with a main single face-centered cubic (FCC) structure. Furthermore, it was observed that the hardness and the yield strength of the high-entropy alloy thin film was about three times that of the bulk samples, and the plastic deformation was inhomogeneous. Our results could provide an in-depth understanding of the mechanics and deformation mechanism for future design of nanocrystalline HEATFs with desired properties.

36 MATERIALS SCIENCE↗

Coexistence of epitaxial Ta(111) and Ta(110) oriented magnetron sputtered thin film on c-cut sapphire

Epitaxial Ta films were grown on c-cut and r-cut sapphire substrates using magnetron sputtering. X-ray diffraction measurements indicate that the Ta films grown on c-cut sapphire substrates have two different crystal orientations. Low vacuum base pressure produced films with the (111) plane parallel to the basal plane after an initial (110) plane growth phase, whereas high base pressure resulted in the growth of (110) plane parallel to the basal plane with three azimuthally oriented domains coexisting. The superconducting critical temperatures T{sub c} of the films grown on c-cut substrates were found to be slightly higher than those for the films grown on r-cut substrates. The x-ray photoelectron spectroscopic data show oxygen content in the high vacuum base pressure deposited films and a difference in the valance band with different Ta surface planes.

36 MATERIALS SCIENCE↗

Deposition of ultrathick heavy-metal alloys on rotating substrates by high-power impulse magnetron sputtering: Target erosion effects

Sputter deposition of ultrathick (≈20μm) Au–Ta alloy coatings on sphero-cylindrical substrates is key for the fabrication of hohlraums for magnetically assisted inertial confinement fusion. In this work, we study the deposition of AuTa 4 alloy coatings onto rotating substrates. We use high-power impulse magnetron sputtering (HiPIMS) in a constant peak target voltage mode. Results show that the target erosion state has a strong impact on the dominant crystallographic phase, microstructure, surface morphology, and electrical resistivity of AuTa 4 films. This is due to effects of changes in the confining magnetic field with target erosion on the HiPIMS discharge characteristics and the sputter source output. We quantify these effects via plasma diagnostics and discuss the optimization of HiPIMS deposition of ultrathick films for cases when target erosion effects dominate film properties.

36 MATERIALS SCIENCE↗