SEARCH · Engineering Papers

Results for “Locating Profile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS2021

Locating the Isolator Shock-Train Leading Edge with Limited Pressure Information

Real-time detection and control of the isolator shock-train leading edge (STLE) is important to the performance of high-speed air-breathing engines, such as dual-mode scramjets. Typically, the STLE location is determined using wall static-pressure measurements, but there are often restrictions on the placement and overall number of the pressure transducers, reducing the viability and accuracy of such approaches. To address these issues, we introduce the adaptive pressure profile (APP) method for estimating the STLE location. This method does not require extensive prior characterization of the isolator or engine model. Instead, it uses real-time pressure measurements from a small number of transducers to adaptively learn the isolator pressure profile and subsequently uses this deduced profile to estimate the STLE location in a data-driven manner. The APP method works well in situations with sparse transducer placement. It produces accurate estimates when the STLE location is 1) not bounded by two or more transducers or 2) between two transducers that are several isolator duct heights apart. We demonstrate the efficacy of the APP method using simulations and experimental data from direct-connect isolator models. This validation shows that the APP method is accurate and robust for different flow regimes, transducer configurations, and model geometries.

Gregory J. Hunt↗

NASA NTRS1977

Wall cooling effects on hypersonic transitional/turbulent boundary layers at high Reynolds numbers

The characteristics of a thick hypersonic boundary layer turbulent for a length of 175 cm on a 4 deg sharp wedge were measured. The resulting boundary layer was free from transverse curvature effects and only mildly affected by upstream history effects caused by pressure and wall temperature gradients. Heat-transfer distributions were used to locate regions of laminar, transitional, and turbulent flow at an edge unit Reynolds number of 470,000 cm at wall-to-total temperature ratios from about 0.3 to 1. Wall cooling had little effect on the location of the transition region. Pitot and total temperature profiles and skin-friction measurements were obtained at several locations along the model longitudinal centerline. Mixing length and turbulent Prandtl number distributions were derived from the fully turbulent mean profiles.

Watson, R. D.↗

NASA NTRSDate not supplied

Airborne Lidar Measurements of Ozone and Aerosol Profiles Over Major US Metropolitan Areas

During field missions in 2021 and 2023, the airborne NASA Langley Research Center High Spectral Resolution Lidar 2 (HSRL 2) measured the temporal and spatial evolution of ozone and aerosol distributions impacting urban air quality over the four most populated cities in the United States. HSRL-2 measurements in 2021 were acquired over the Houston metropolitan region, including Galveston Bay and the Houston Ship Channel, as part of the NASA Tracking Aerosol Convection Experiment – Air Quality (TRACER-AQ) mission conducted in collaboration with the Department of Energy. HSRL-2 measurements were acquired over Los Angeles, Chicago, and New York City in 2023 as part of the NASA Synergistic TEMPO Air Quality Science (STAQS) mission conducted in collaboration with the NOAA Atmospheric Emissions and Reactions Observed from Megacities to Marine Areas (AEROMMA) mission. HSRL 2 provided nadir vertical profiles of ozone, aerosol backscatter, extinction, and depolarization as the aircraft flew lawnmower type patterns at 9 km for several hours over these urban areas. HSRL-2 measured profiles of aerosol extinction and aerosol optical depth (AOD) via the HSRL technique at 355 and 532 nm and profiles of aerosol backscatter and depolarization at 355, 532, and 1064 nm. Mixed Layer Heights (MLH) were derived by locating sharp vertical gradients in the profiles of aerosol backscatter. The flights were comprised of up to three repeating lawnmower patterns over each city showing the evolution of the ozone and aerosol distributions from the morning through the afternoon. The HSRL-2 measurements reveal ozone enhancements near the surface as well as in the free troposphere above the mixed layer. Some lidar measurements over Chicago and New York City show the daytime boundary layer growing into elevated layers of biomass burning aerosol. These layers complicate efforts to use column-integrated satellite measurements to infer surface air quality. As expected, mixed layer height (MLH) typically increased significantly during the day; however, during some flights, particularly over the Houston area, MLH also showed large spatial variability associated with changes in surface cover and/or small scale circulations. Often HSRL-2 measurements of AOD also showed large spatial and temporal variability throughout the day over these cities. We discuss how the ozone and aerosol profiles are averaged over different vertical and horizontal scales near the surface for use in assessments of regional air quality models and near-surface ozone retrievals from NASA’s recently launched Tropospheric Emissions: Monitoring Pollution (TEMPO) satellite.

Lidar↗

NASA NTRSDate not supplied

HSRL-2 Observations over the Houston, TX Region during TRACER-AQ

Lidar↗

NASA NTRS1985

Traffic scenario generation technique for piloted simulation studies

Piloted simulation studies of cockpit traffic display concepts require the development of representative traffic scenarios. With the exception of specific aircraft interaction issues, most research questions can be addressed using traffic scenarios consisting of prerecorded aircraft movements merged together to form a desired traffic pattern. Prerecorded traffic scenarios have distinct research advantages, allowing control of traffic encounters with repeatability of scenarios between different test subjects. A technique is described for generation of prerecorded jet transport traffic scenarios suitable for use in piloted simulation studies. Individual flight profiles for the aircraft in the scenario are created interactively with a computer program designed specifically for this purpose. The profiles are then time-correlated and merged into a complete scenario. This technique was used to create traffic scenarios for the Denver, Colorado area with operations centered at Stapleton International Airport. Traffic scenarios for other areas may also be created using this technique, with appropriate modifications made to the navigation fix locations contained in the flight profile generation program.

Williams, David H.↗

DOE OSTI2023

Temperature Uncertainty Modeling with Proxy Structural Data as Geostatistical Constraints for Well Siting: An Example Applied to Granite Springs Valley, NV, USA

Utilizing existing temperature and structural information around Granite Springs Valley, Nevada, we build 3D stochastic temperature models with the aim of evaluating the 3D uncertainty of temperature and choosing between candidate exploration well locations . The data used to support the modeling are measured temperatures and structural proxies from 3D geologic modeling, the latter considered "secondary" data. Two stochastic geostatistical techniques are explored for incorporating the structural proxies: cosimulation and local varying mean. With both the cosimulation and local varying mean methods, many equally likely temperature models (i.e., realizations) are produced, from which temperature probability profiles are calculated at candidate well locations. To aid in choosing between the candidate locations, two quantities summarize the temperature probabilities: Vprior and entropy. Vprior quantifies the likelihood for economic temperatures at each candidate location, whereas entropy identifies where new information has the most potential to reduce uncertainty. In general, the cosimulation realizations have smoother spatial structure, and extrapolate high temperatures at candidate locations that are located along the direction of the longest spatial correlation, which are down dip from existing temperature logs. The smooth realizations result in tight temperature probability profiles that are easier to interpret, but they have unrealistic temperature reversals in some locations because the cosimulation technique does not enforce a conductive geothermal gradient as a baseline (i.e., linearly increasing temperature with depth). The local varying mean results produce realizations with more realistic geothermal gradients, with temperatures increasing downward since a depth-temperature relationship is included. However, because they have much noisier spatial nature compared to cosimulation, it is harder to interpret the temperature probability profiles. The different local varying mean results allow the geologist to determine which proxy (e.g., dilation versus distance to fault termination) should be used given the specific geothermal system. In general, Vprior from local varying mean results identify locations that are close to high values for the structural proxies: areas with highe r probabilities for higher temperatures. The entropy results identify where uncertainty is greatest and therefore new drilling information could be most useful. Though these techniques provide useful information, even when applied to areas of sparse data, our comp arison of these two techniques demonstrates the need for new geothermal geostatistics techniques that combine the advantages of these two methods and that are tailored to the spatial uncertainty issues inherent in geothermal exploration.

3D temperature modeling↗

DOE OSTI2023

Temperature uncertainty modelling with proxy structural data as geostatistical constraints for well siting: an example applied to Granite Springs Valley, NV, USA

Utilizing existing temperature and structural geology information around Granite Springs Valley, Nevada, we build 3D stochastic temperature models with the aims of evaluating the 3D uncertainty of temperature and choosing between candidate exploration well locations. The data used to support the modelling are measured temperatures and structural proxies from 3D geologic modelling (distance to fault, distance to fault intersections and terminations, Coulomb stress change and dilation tendency), the latter considered ‘secondary’ data. Two stochastic geostatistical techniques are explored for incorporating the structural proxies: cosimulation and local varying mean. With both the cosimulation and local varying mean methods, many equally-likely temperature models (i.e. realizations) are produced, from which temperature probability profiles are calculated at candidate well locations. To aid in choosing between the candidate locations, two quantities summarize the temperature probabilities: V prior and entropy. V prior quantifies the likelihood for economic temperatures at each candidate location, whereas entropy identifies where new information has the most potential to reduce uncertainty. In general, the cosimulation realizations have smoother spatial structure, and extrapolate high temperatures at candidate locations that are located along the direction of the longest spatial correlation, which are down dip from existing temperature logs. The smooth realizations result in tight temperature probability profiles that are easier to interpret, but they have unrealistic temperature reversals in some locations because of the dipping ellipsoid shape created and that the cosimulation technique does not enforce a conductive geothermal gradient as a baseline (i.e. linearly increasing temperature with depth). The local varying mean results produce realizations with more realistic geothermal gradients, with temperatures increasing downward since a depth-temperature relationship is included. However, because they have much noisier spatial nature compared to cosimulation, it is harder to interpret the temperature probability profiles. The different local varying mean results allow the geologist to determine which proxy (e.g. dilation v. distance to fault termination) should be used given the specific geothermal system. In general, V prior from local varying mean results identify locations that are close to high values for the structural proxies: areas with higher probabilities for higher temperatures. The entropy results identify where uncertainty is greatest and therefore new drilling information could be most useful. Though these techniques provide useful information, even when applied to areas of sparse data, our comparison of these two techniques demonstrates the need for new geothermal geostatistics techniques that combine the advantages of these two methods and that are tailored to the spatial uncertainty issues inherent in geothermal exploration.

15 GEOTHERMAL ENERGY↗

NASA NTRS2008

User Guide for the Anvil Threat Cooridor Forecast Tool V2.4 for AWIPS

The Anvil Tool GUI allows users to select a Data Type, toggle the map refresh on/off, place labels, and choose the Profiler Type (source of the KSC 50 MHz profiler data), the Date- Time of the data, the Center of Plot, and the Station (location of the RAOB or 50 MHz profiler). If the Data Type is Models, the user selects a Fcst Hour (forecast hour) instead of Station. There are menus for User Profiles, Circle Label Options, and Frame Label Options. Labels can be placed near the center circle of the plot and/or at a specified distance and direction from the center of the circle (Center of Plot). The default selection for the map refresh is "ON". When the user creates a new Anvil Tool map with Refresh Map "ON, the plot is automatically displayed in the AWIPS frame. If another Anvil Tool map is already displayed and the user does not change the existing map number shown at the bottom of the GUI, the new Anvil Tool map will overwrite the old one. If the user turns the Refresh Map "OFF", the new Anvil Tool map is created but not automatically displayed. The user can still display the Anvil Tool map through the Maps dropdown menu* as shown in Figure 4.

Barett, Joe H., III↗

DOE OSTI2022

Deploying Taller Turbines in Complex Terrain: A Hill Flow Study (HilFlowS) Perspective

Terrain-induced flow acceleration is presented for the summertime, peak power season at Lawrence Livermore National Laboratory’s Site 300 for the Hill Flow Study (HilFlowS). HilFlowS, designed as an adjunct field campaign to the Department of Energy’s Second Wind Forecasting Improvement Project (WFIP2), provides wind profile observations at a second location in complex terrain for validating numerical atmospheric model simulations and for better understanding flow behavior over hills for wind power generation. One unique feature of HilFlowS was the inclusion of an undergraduate university student who helped plan and execute the experiment as well as analyze wind data from two remote sensing laser detection and ranging (lidar) instruments deployed along parallel ridgelines. HilFlowS examines the trend of building higher into the atmosphere for the purpose of increasing wind turbine power production and evaluates the wind resource in the Altamont Pass Region of Northern California for a set of wind turbines of differing hub-heights and rotor-disk diameters found in the area. The wind profiles show strongly channeled onshore flow above both hills, enhanced by strong subsidence aloft, which produces a wind maximum (Umax) around z = 10 m and strong negative shear throughout all of the evaluated rotor-disks for much of the summer wind season. Under these conditions, shear becomes more negative with increasing hub-height and increasing rotor-disk size. Rotor-disk equivalent wind speed (Uequiv), a measure of the average wind speed across the entire rotor-disk, is compared to hub-height, rotor length, and rated capacity factor for the set of turbines. Uequiv is most closely related to turbine hub-height and is negatively correlated given the low altitude of Umax. Based on these results, building the largest capacity, large rotor-disk wind turbine at the lowest possible hub-height appears to provide turbines in the Altamont with a fast, near-surface, onshore wind resource during the peak power season.

17 WIND ENERGY↗

DOE OSTI2021

Investigating profile stiffness and critical gradients in shaped TCV discharges using local gyrokinetic simulations of turbulent transport

The experimental observation made on the TCV tokamak of a significant confinement improvement in plasmas with negative triangularity ( δ < 0) compared to those with standard positive triangularity has been interpreted in terms of different degrees of profile stiffness (Sauter et al. Phys. Plasmas 21 055906, 2014) and/or different critical gradients. Employing the Eulerian gyrokinetic code GENE (Jenko et al. Phys. Plasmas 7 1904, 2000), profile stiffness and critical gradients are studied under TCV relevant conditions. For the considered experimental discharges, trapped electron modes (TEMs) and electron temperature gradient (ETG) modes are the dominant microinstabilities, with the latter providing a significant contribution to the non-linear electron heat fluxes near the plasma edge. Two series of simulations with different levels of realism are performed, addressing the question of profile stiffness at various radial locations. Retaining finite collisionality, impurities and electromagnetic effects, as well as the physical electron-to-ion mass ratio are all necessary in order to approach the experimental flux measurements. However, flux-tube simulations are unable to fully reproduce the TCV results, pointing towards the need to carry out radially nonlocal (global) simulations, i.e. retaining finite machine size effects, in a future study. Some conclusions about the effect of triangularity can nevertheless be drawn based on the flux-tube results. In particular, the importance of considering the sensitivity to both temperature and density gradient is shown. The flux tube results show an increase of the critical gradients towards the edge, further enhanced when δ < 0, and they also appear to indicate a reduction of profile stiffness towards plasma edge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Effect of macroscopic surface defects on dynamic damage: An experimental and numerical study

This study examines the impact of macroscopic surface defects on the dynamic ductile damage behavior of polycrystalline metals using plate-impact experiments. Defects of various shapes (flat, round, and point) were manufactured on the free or impact surfaces of annealed copper specimens. The experiments were diagnosed with photon Doppler velocimetry measurements and soft recovery techniques. The experimental results revealed that defect shape and location significantly affect velocity–time profiles and void distribution. In order to understand the dynamics of shock propagation and corresponding ductile damage evolution within the target specimens, the impact experiments were modeled with a calibrated Tepla model, a dynamic ductile damage model for polycrystalline metals [Nguyen et al., Int. J. Solids Struct. 329, 113833 (2026)]. Overall, our resulting simulated velocity showed good agreement with measured velocity, and our simulated porosity distributions qualitatively matched experimental data. Based on our simulation results, defects on the free surface were found to distort rarefaction waves and therefore the corresponding spall planes. On the other hand, defects on the impact surface generated a delayed shock when the flyer plate and the defected target area were in contact, leading to distortion of the spall plane. The distortion of the spall plane resulted in a non-uniform distribution of voids within the defected specimens. Lastly, we examined the role of local work hardening due to the defect manufacturing process on the velocity and porosity distribution, using Tepla simulations with a simplified representation of local hardening. This investigation highlights the importance of defect geometry, location, and local hardening associated with defect generation in dynamic ductile damage processes.

36 MATERIALS SCIENCE↗

NASA NTRS1993

Stability of hypersonic boundary-layer flows with chemistry

The effects of nonequilibrium chemistry and three dimensionality on the stability characteristics of hypersonic flows are discussed. In two-dimensional (2-D) and axisymmetric flows, the inclusion of chemistry causes a shift of the second mode of Mack to lower frequencies. This is found to be due to the increase in size of the region of relative supersonic flow because of the lower speeds of sound in the relatively cooler boundary layers. Although this shift in frequency is present in both the equilibrium and nonequilibrium air results, the equilibrium approximation predicts modes which are not observed in the nonequilibrium calculations (for the flight conditions considered). These modes are superpositions of incoming and outgoing unstable disturbances which travel supersonically relative to the boundary-layer edge velocity. Such solutions are possible because of the finite shock stand-off distance. Their corresponding wall-normal profiles exhibit an oscillatory behavior in the inviscid region between the boundary-layer edge and the bow shock. For the examination of three-dimensional (3-D) effects, a rotating cone is used as a model of a swept wing. An increase of stagnation temperature is found to be only slightly stabilizing. The correlation of transition location (N = 9) with parameters describing the crossflow profile is discussed. Transition location does not correlate with the traditional crossflow Reynolds number. A new parameter that appears to correlate for boundary-layer flow was found. A verification with experiments on a yawed cone is provided.

Reed, Helen L.↗

NASA NTRS1977

Cold plasma diagnostics using satellite measurements of VLF signals from ground transmitters

A diagnostic technique to obtain the cold-plasma density profile in the magnetosphere is introduced. This method uses satellite measurements of group delay and pulse duration of VLF signals from ground transmitters in conjunction with a detailed ray-tracing analysis. An iterative method is involved which starts with an approximate density profile, computes the ray paths for that profile, and then compares the properties of the rays that reach the satellite location with the actual satellite measurements. The density profile is then modified to account for any discrepancies between the two results. The same process is repeated with the new profile until one has reasonable agreement between the data and ray-tracing results. This method is applied to the case of an Imp 6 pass, where strong signals from the Siple VLF transmitter were observed for over 25 min. Good agreement is found between the results of the proposed technique and the well-known ground whistler techniques of cold-plasma diagnostics. The results also serve to illustrate the wide diversity of propagation paths from ground transmitters to high-altitude satellites during VLF wave-injection experiments.

Inan, U. S.↗

DOE OSTI2024

Factors Influencing Grid-connected Heat Pump Water Heater Performance in the Southeast U.S.

Grid-connected heat pump water heaters (HPWH) can shift electrical load while minimizing impacts to hot water availability for occupants. This capability provides a flexible grid resource to utilities seeking to manage peak loads Such load control also can feasibly improve renewable utilization within the utility electric production mix, for instance using off-peak generation during periods with high renewable energy generation. It also offers lower electric bills to customers through increased energy efficiency of HPWH and cuts greenhouse gas emissions. In particular, the Southeast U.S. due to its high penetration of electric water heating presents a promising opportunity for grid-connected HPWHs. This paper builds upon the results of an extensive HPWH load shifting field study conducted in 51 occupied homes in Florida using EcoPort technology (Butzbaugh et al, 2022). In 2022, only an initial evaluation was available. Here, long term load results are available as well as examination of various control strategies and influences. Analysis is conducted for HPWH energy use and load shifting performance based on home occupancy (i.e., low and high) and water heater location (i.e., conditioned and unconditioned) across different temperature profiles. An unexpected outcome of this analysis was the poor performance of HPWHs located in conditioned spaces, possibly because of inadequate air volume from improper installation. We did find higher demand reductions from 2-hour load ups and slightly improved for critical peak signals in the afternoon control periods. As expected, higher occupancy households showed great load reductions.

Fenaughty, Karen↗

DOE OSTI2021

Data–Driven Velocity Model Evaluation Using K–Means Clustering

In this work, we develop a data-driven clustering method to evaluate a velocity model using surface wave velocity dispersion. This is done by first computing theoretical dispersion curves for 1-D velocity profiles of all the grid locations and then splitting the resulting dispersion curves into a certain number of groups via the K-means clustering. The observed dispersion curves are also clustered following the same procedure and the velocity model is assessed by comparing the spatial patterns obtained for the observed and synthetic data sets. The method is applied to evaluate two community velocity models in southern California, CVM-S4.26 and CVM-H15.1, using phase velocity maps derived for 3–16 s Rayleigh waves. We found a good correlation in the spatial distribution of clusters between the result of CVM-S4.26 and that of the observed data, suggesting that the CVM-S4.26 fits the observed dispersion maps better than the CVM-H15.1 in terms of features extracted from the clustering analysis.

58 GEOSCIENCES↗

DOE OSTI2022

Flexocaloric effect in superelastic materials

We present a combined theoretical–experimental study of flexocaloric effects in superelastic materials exhibiting structural transitions. We study a Ginzburg–Landau model combined with a vibrational model for a beam near a ferroelastic transition loaded with a three-point bending setup. We also perform experiments on a Cu–Al–Ni single crystal undergoing a martensitic transition. We measure bent beam profiles, vertical force vs vertical deflection during a slow isothermal process, time evolution of the bending and unbending amplitudes, and the evolution of temperature profiles. We also compute the evolution of heat source and heat sink profiles. Finally, we study the location of acoustic emission events during the bending/unbending experiment. Our observations are consistent with the model predictions and allow us to identify the main physical parameters relevant for flexocaloric applications.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Integrated control of individual plasma scalars with simultaneous neoclassical tearing-mode suppression

A novel integrated-control architecture has been tested in nonlinear, one-dimensional simulations using the control-oriented transport simulator (COTSIM©) and in DIII-D experiments. Integrated architectures that can perform continuous-mission control while also handling off-normal events will be vital in future reactor-grade tokamaks. Continuous-mission controllers for individual magnetic and kinetic scalars (thermal stored-energy (W), volume-average toroidal rotation (Ω Φ ), and safety factor profile (q) at different spatial locations) have been integrated in this work with event-triggered neoclassical tearing-mode (NTM) suppression controllers by combining them into an architecture augmented by a supervisory and exception handling (S&EH) system and an actuator management (AM) system. Here, the AM system, which enables the integration of competing controllers, solves in real time a nonlinear optimization problem that takes into account the high-level control priorities dictated by the S&EH system. The resulting architecture offers a high level of integration and some of the functionalities that will be required to fulfill the advanced-control requirements anticipated for ITER. Initial simulations using COTSIM suggest that the plasma performance and its MHD stability may be improved under integrated feedback control. In addition, the integrated-control architecture has been implemented in the DIII-D plasma control system and tested experimentally for the first time ever in DIII-D in a high-q min scenario, which is a candidate for steady-state operation in ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Dynamic Rhizodeposition in the Woody Perennial Populus trichocarpa

Plants undergo physiological and metabolic changes that release specific molecules into the surrounding soil, a process collectively known as rhizodeposition. These compounds play crucial roles in plant‐microbe‐soil interactions, such as supporting plant development and resilience in changing environments. Under nutrient‐limited conditions, these plant‐derived compounds modify the rhizosphere environment, mobilizing otherwise inaccessible nutrients and recruiting stress‐adaptive microbial communities that support stress resilience. Currently, the chemical diversity of rhizodeposition has yet to be fully realized but is expected to be a complex mixture that includes soluble organic compounds excreted from root cells, along with products of root cell turnover, sloughed‐off root cap and border cells, and mucilage. Here, we developed a methodological and conceptual framework for an in‐depth measurement of rhizodeposition through critical advancements in untargeted metabolomics. Further, this approach provided foundational insights into the dynamic changes in rhizodeposition for the woody perennial Populus trichocarpa and rhizodeposit profiles varying by genotype, time, location, and environment. More broadly, this study provides a framework that will help formulate the next steps to effectively study rhizodeposition.

59 BASIC BIOLOGICAL SCIENCES↗