SEARCH · Engineering Papers

Results for “LiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

NASA NTRS1976

Wind-tunnel investigation of a Fowler flap and spoiler for an advanced general aviation wing

The wing was tested without fuselage or empennage and was fitted with approximately three-quarter span Fowler flaps and half span spoilers. The spoilers were hinged at the 70 percent chord point and vented when the flaps were deflected. Static longitudinal and lateral aerodynamic data were obtained over an angle of attack range of -8 deg to 22 deg for various flap deflections and positions, spoiler geometries, and vent lip geometries. Lateral characteristics indicate that the spoilers are generally adequate for lateral control. In general, the spoiler effectiveness increases with increasing angle of attack, increases with increasing flap deflections, and is influenced by vent lip geometry. In addition, the data show that some two-dimensional effects on spoiler effectiveness are reduced in the three-dimensional case. Results also indicate significant increase in lift coefficient as the Fowler flaps are deflected; when the flap was fully deflected, the maximum wing lift coefficient was increased about 96 percent.

Paulson, J. W., Jr.↗

NASA NTRS1976

Investigation of two bifurcated-duct inlet systems from Mach 0 to 2.0 over a wide range of angles of attack

A 15.354 percent/scale lightweight fighter type inlet/forebody was tested over a Mach number range of 0 to 2.0. Model configurations consisted of side mounted normal shock and fixed overhead ramp type inlets. Each configuration consisted of two inlets ducted (bifurcated) to supply a single engine face. The normal shock inlet variables included a boundary layer splitter bleed system, alternate boundary layer splitter plates, alternate upper and lower cowl lip shapes, and a blow-in-door (auxiliary inlet) in one lower lip. The only variable of the fixed overhead ramp inlet was the boundary layer bleed flow. Reynolds numbers ranged from 7.6 x 1 million to 19.5 x 1 million/m. Angle of attack ranged from -10 to 35 deg and angle of sideslip from -8 to 8 deg. Test measurements included engine face total pressure recovery, steady state distortion, dynamic distortion, and surface static pressures on the forebody and inlet surfaces.

Latham, E. A.↗

NASA NTRS1975

Quiet Clean Short-Haul Experimental Engine (QCSEE) aerodynamic characteristics of 30.5 centimeter diameter inlets

A low speed test program was conducted in a 9- by 15-foot V/STOL wind tunnel to investigate internal performance characteristics and determine key design features required for an inlet to meet the demanding operational conditions of the QCSEE application. Four models each having a design average throat Mach number of 0.79 were tested over a range of incidence angle, throat Mach number, and freestream velocity. Principal design variable was internal lip diameter ratio. Stable, efficient inlet performance was found to be feasible at and beyond the 50 deg incidence angle required by the QCSEE application at its 41.2 m/sec (80 knot) nominal takeoff velocity, through suitably designed inlet lip and diffuser components. Forebody design was found to significantly impact flow stability via nose curvature. Measured inlet wall pressures were used to select a location for the inlet throat Mach number control's static pressure port that properly balanced the conflicting demands of relative insensitivity to flow incidence and sufficiently high response to changes in engine flow demand.

Paul, D. L.↗

NASA NTRS1977

Prediction of Laminar and Turbulent Boundary Layer Flow Separation in V/STOL Engine Inlets

A description is presented of the development of the boundary layer on the lip and diffuser surface of a subsonic inlet at arbitrary operating conditions of mass flow rate, free stream velocity and incidence angle. Both laminar separation on the lip and turbulent separation in the diffuser are discussed. The agreement of the theoretical results with model experimental data illustrates the capability of the theory to predict separation. The effects of throat Mach number, inlet size, and surface roughness on boundary layer development and separation are illustrated.

Chou, D. C.↗

NASA NTRS1977

Experimental evaluation of nacelle-airframe interference forces and pressures at Mach numbers of 0.9 to 1.4

Detailed interference force-and-pressure data were obtained on a representative supersonic transport wing-body-nacelle combination at Mach numbers of 0.9 to 1.4. The basic model consisted of a delta wing-body aerodynamic model with a length of 158.0 cm (62.2 in.) and a wingspan of 103.6 cm (40.8 in.) and four independently supported nacelles positioned beneath the model. The experimental program was conducted in the Ames 11- by 11-Foot Wind Tunnel at a constant unit Reynolds number. The primary variables examined included Mach number, angle of attack, nacelle position, and nacelle mass-flow ratio. Under the most favorable conditions, the net interference drag was equal to 50 percent the drag of four isolated nacelles at M = 1.4, 75 percent at M = 1.15, and 144 percent at M = 0.90. The overall interference effects were found to be rather constant over the operating angle-of-attack range of the configuration. The effects of mass-flow ratio on the interference pressure distributions were limited to the lip region of the nacelle and the local wing surface in the immediate vicinity of the nacelle lip. The net change in the measured interference forces resulting from variations in the nacelle mass-flow ratio were found to be quite small.

Bencze, D. P.↗

NASA NTRS1977

Investigation of Inlet Concepts for Maneuver Improvement at Transonic Speeds

A 15 percent scale lightweight fighter type inlet forebody was tested in the Ames 14 foot transonic wind tunnel at Mach numbers of 0.7, 0.9, and 1.04. The inlet was a two dimensional horizontal ramp system designed for a Mach number of 2.2. Four inlet devices designed to prevent or delay cowl-lip boundary layer separation or to improve the inlet internal flow characteristics at high angles of attack were investigated. The devices used to control cowl-lip separation consisted of cowl leading edge flaps, slotted flaps, and tangential blowing. To improve the internal flow characteristics, discrete jet nozzle flows were directed downstream and parallel to the duct surface in the subsonic diffuser to energize the wall boundary layer. The discrete jets used in the subsonic diffuser were also tested in combination with each of the cowl leading edge devices. Test measurements included engine-face total pressure recovery, steady state distortion, dynamic distortion, duct boundary layer profiles, and duct-surface static pressures.

Latham, E.↗

NASA NTRS1977

Prediction of laminar and turbulent boundary layer flow separation in V/STOL engine inlets

The paper provides a theoretical description of the development of the boundary layer on the lip and diffuser surface of a subsonic inlet at arbitrary operating conditions of mass flow rate, freestream velocity and incidence angle. Both laminar separation on the lip and turbulent separation in the diffuser are discussed. The agreement of the theoretical results with model experimental data illustrates the capability of the theory to predict separation. The effects of throat Mach number, inlet size, and surface roughness on boundary-layer development and separation are illustrated.

Chou, D. C.↗

NASA NTRS1978

Theoretical flow characteristics of inlets for tilting-nacelle VTOL aircraft

The results of a theoretical investigation of geometric variables for lift-cruise-fan, tilting nacelle inlets operating at high incidence angles are presented. These geometric variables are investigated for their effects on surface static to free stream pressure ratio, and the separation parameters of maximum to diffuser exit surface velocity ratio and maximum surface Mach number for low speed operating conditions. The geometric parameters varied were the internal lip contraction ratio, external forebody to diffuser exit diameter ratio external forebody length to diameter ratio and internal lip major to minor axis ratio.

Boles, M. A.↗

NASA NTRS1976

Acoustics and aerodynamics of over-the-wing thrust reversers

As part of the Quiet Clean Short-Haul Experimental Engine Program, model tests were conducted to determine the effects of thrust reverser geometric parameters on noise and reverse thrust. The acoustic tests used a 1/6 scale model thrust reverser while the aerodynamic performance tests used a 1/12 scale model reverser. Parameters which were varied in both tests include blocker spacing, blocker height, lip angle, and lip length. The impact of these parameters on peak sideline noise and reverse thrust performance is discussed.

Stimpert, D. L.↗

NASA NTRS1979

Theoretical study of VTOL tilt-nacelle axisymmetric inlet geometries

A systematic theoretical study of VTOL tilt-nacelle inlet design parameters is reported. The parameters considered are internal-lip contraction ratio, internal-lip major-to-minor axis ratio, diffuser-exit-area to throat-area ratio, maximum diffuser wall angle and shape. Each of the inlets was analyzed at the same given flow condition of free-stream velocity, angle between the free stream and centerline of the inlet, and diffuser-exit Mach number. The effects of these geometric parameters on surface static-pressure distribution, peak surface Mach number, diffusion velocity ratio, and tendency for the inlet flow to separate are presented.

Hawk, J. D.↗

NASA NTRS1979

Aerodynamic performance of scarf inlets

A scarf inlet is characterized by having a longer lower lip than upper lip leading to both aerodynamic and acoustic advantages. Aerodynamically, a scarf inlet has higher angle of attack capability and is less likely to ingest foreign objects while the aircraft is on the ground. Acoustically, a scarf inlet provides for reduced inlet radiated noise levels below the engine as a result of upward reflection and refraction of inlet radiated noise. Results of a wind tunnel test program are presented which illustrate the aerodynamic performance of two different scarf inlet designs. Based on these results, scarf inlet performance is summarized in a way to illustrate the advantages and limitations of a scarf inlet compared to an axisymmetric inlet.

Abbott, J. M.↗

NASA NTRS1979

Aerodynamic performance of scarf inlets

Abbott, J. M.↗

NASA NTRS1978

Quiet Clean Short-Haul Experimental Engine (QCSEE) acoustic and aerodynamic tests on a scale model over-the-wing thrust reverser and forward thrust nozzle

An acoustic and aerodynamic test program was conducted on a 1/6.25 scale model of the Quiet, Clean, Short-Haul Experimental Engine (QCSEE) forward thrust over-the-wing (OTW) nozzle and OTW thrust reverser. In reverse thrust, the effect of reverser geometry was studied by parametric variations in blocker spacing, blocker height, lip angle, and lip length. Forward thrust nozzle tests determined the jet noise levels of the cruise and takeoff nozzles, the effect of opening side doors to achieve takeoff thrust, and scrubbing noise of the cruise and takeoff jet on a simulated wing surface. Velocity profiles are presented for both forward and reverse thrust nozzles. An estimate of the reverse thrust was made utilizing the measured centerline turning angle.

Stimpert, D. L.↗

NASA NTRS1979

Glossary of terms and table of conversion factors used in design of chemical propulsion systems

The glossary presented is based entirely on terms used in the monographs on Chemical Propulsion. Significant terms relating to material properties and to material fabrication are presented. The terms are arranged in alphabetical order, with multiple word terms appearing in the normal sequence of usage; for example, ablative cooling appears as such, not as cooling, ablative, and lip seal appears as such, not as seal, lip. Conversion Factors for converting U.S. customary units to the International System of Units are presented in alphabetical order of the physical quantity (e.g., density, heat flux, specific impulse) involved.

Keller, R. B., Jr.↗

NASA NTRS1980

An improved sensing element for skin-friction balance measurements

A nulling, parallel-linkage sensing element has been developed for a skin-friction balance in order to minimize the introduction of extraneous forces. Advantages of the present element over the conventional single-pivot sensing element include its insensitivity to element misalignment and off-center normal forces. Wind tunnel tests of the effects of gap size and element misalignment on parallel-linkage balance measurements indicate the greater sensitivity of the device to misalignment at small gap sizes and large lip sizes, as well as its relative insensitivity to off-center normal forces. It is concluded that a parallel-linkage device with a small lip is virtually insensitive to gap size and element misalignment, representing an improvement in skin-friction-measuring characteristics.

Allen, J. M.↗

NASA NTRS1981

Turbomachinery noise studies of the AiResearch QCGAT engine with inflow control

The AiResearch Quiet Clean General Aviation Turbofan engine was tested on a vertical lift fan facility to measure the acoustic performance of two inflow control devices (ICD) of similar design, and three inlet lips of different external shape. Far-field directivity patterns calculated by existing analyses were compared with the measured fan fundamental blade passing frequency (BPF/F/) and broadband data. Installing an ICD on an engine with hardwall ducts reduced the BPF(F) tone everywhere in the far-field. When the ICD was installed on an engine with active acoustic panels, tone reduction in the forward quadrant was comparable to that in the hardwall tests; in the aft quadrant, however, tone noise was attenuated by the large acoustic panels in the bypass duct to such a degree that the ICD had little effect. Tests to compare performance of ICDs with hardwall inlet ducts showed only minor differences in the BPF(F) directivity patterns, while broadband noise was the same for both. Forward-quadrant BPF(F) and broadband directivity patterns were found to be similar for the inlet lips tested with a hardwall inlet duct. At high fan speeds, however, the shape of the analytical multimodal tone pattern from the exhaust nozzle was flatter than the measured patterns. The sources of lobes from several propagating single modes found in the forward-quadrant BPF(F) data were attributed to rotor/strut interaction and the rotor-alone pressure field.

Mcardle, J. G.↗

NASA NTRS1982

Effects of axisymmetric and normal air jet plumes and solid plume on cylindrical afterbody pressure distributions at Mach numbers from 1.65 to 2.50

A wind tunnel investigation of the interference effects of axisymmetric nozzle air plumes, a solid plume, and normal air jet plumes on the afterbody pressure distributions and base pressures of a cylindrical afterbody model was conducted at Mach numbers from 1.65 to 2.50. The axisymmetric nozzles, which varied in exit lip Mach number from 1.7 to 2.7, and the normal air jet nozzle were tested at jet pressure ratios from 1 (jet off) to 615. The tests were conducted at an angle of attack of 0 deg and a Reynolds number per meter of 6.56 million. The results of the investigation show that the solid plume induces greater interference effects than those induced by the axisymmetric nozzle plumes at the selected underexpanded design conditions. A thrust coefficient parameter based on nozzle lip conditons was found to correlate the afterbody disturbance distance and the base pressure between the different axisymmetric nozzles. The normal air jet plume and the solid plume induce afterbody disturbance distances similar to those induced by the axisymmetric air plumes when base pressure is held constant.

Covell, P. F.↗

NASA NTRS1983

Staked Bearing Removal Tool

Tool with assembled components expedites bearing replacement in aircraft, ground vehicles, and other applications. New tool cuts lip on one side to facilitate bearing replacement. After bearing retaining lip is cut away, bearing pressed out. Tool makes it possible to replace bearings without disassembling structure.

Berson, L. A.↗