Results for “Gap Assessment” — Page 12

DOE OSTI2023

AGR-5/6/7 Thermal Model with Non-uniform Gas Gaps

Fuel compact temperatures are a crucial factor in assessing the irradiation performance of tri-structural isotropic fuel particles. In the absence of direct measurement, fuel compact temperatures were calculated using a three-dimensional finite element thermal model, which is subject to simulation uncertainty. The most dominant factor in the uncertainty of calculated fuel temperatures is the gas gap uncertainty due to the nub-to-shell clearance caused by a design error of AGR-5/6/7 capsules. The thermal model was revised to examine the most probable graphite offset position for six different days during the irradiation for Capsules 1 and 2. The analysis varied the offset distance and azimuthal direction at both the top and bottom of the holder. The best-fit offset was estimated based on the minimum root mean square error of the residuals (measured minus calculated) for the operational thermocouples (TCs). From these results, the following conclusions were made: (1) The holder offsets led to slightly lower average temperatures but wider temperature variations (lower minimum and higher peak fuel temperatures) for both Capsule 1 and Capsule 2. (2) During earlier cycles (162A–164B), when numerous TCs were still operational, the best-fit offset distance varied over a specific range for both the top and bottom ([0.002–0.0035 in.] for Capsule 1 and [0.003-0.004 in] for Capsule 2). In contrast, the offset azimuthal direction varied widely, especially for the offset at the bottom of the Capsule 1 holder. This is because holder movement was somewhat constrained at the top of Capsule 1 by the TC leads running through the capsule head and into the holder and by the through tubes in Capsule 2, but the Capsule 1 bottom did not have this type of constraint. (3) During later cycles, when all TCs failed, applying the maximum possible offset of 0.006 in. to the northwest direction for both the top and bottom resulted in a calculated peak fuel temperature of 1557? in Capsule 1 (i.e., a 135? increase from 1422? with zero offset on September 20, 2019 (166A)); the maximum offset of 0.0068 in. to the south for both top and bottom resulted in a calculated peak fuel temperature of 1110°C in Capsule 2 on April 20, 2020 (i.e., a 116? increase from 994? with zero offset (168A)). High peak fuel temperatures in Capsule 1 during Cycle 166A could be the cause of massive particle failure near the end of this cycle. (4) Even though the highest temperature at the tip of Type-N TCs, such as TC-1-7, slightly exceeded 1000?, the temperature along the TC wire reached as high as 1335? assuming an offset of 0.006 in. in the northwest of Capsule 1 holder near the end of Cycle 166A. This temperature significantly exceeds the temperature threshold at which TC degradation is expected to occur, ultimately contributing to considerable particle failures in Capsule 1. For eight Type-N TCs in Capsule 2, the peak TC line temperature was much lower (i.e., 1029°C for TC-2-5), assuming maximum offset of 00068 in. to the south during cycle 168A.

advanced gas reactors↗

DOE OSTI2023

AGR-5/6/7 Thermal Model with Non-uniform Gas Gaps

Fuel compact temperatures are a crucial factor in assessing the irradiation performance of tri-structural isotropic fuel particles. In the absence of direct measurement, fuel compact temperatures were calculated using a three-dimensional finite element thermal model, which is subject to simulation uncertainty. The most dominant factor in the uncertainty of calculated fuel temperatures is the gas gap uncertainty due to the nub-to-shell clearance caused by a design error of AGR-5/6/7 capsules. The thermal model was revised to examine the most probable graphite offset position for six different days during the irradiation for Capsules 1 and 2. The analysis varied the offset distance and azimuthal direction at both the top and bottom of the holder. The best-fit offset was estimated based on the minimum root mean square error of the residuals (measured minus calculated) for the operational thermocouples (TCs). From these results, the following conclusions were made: (1) The holder offsets led to slightly lower average temperatures but wider temperature variations (lower minimum and higher peak fuel temperatures) for both Capsule 1 and Capsule 2. (2) During earlier cycles (162A–164B), when numerous TCs were still operational, the best-fit offset distance varied over a specific range for both the top and bottom ([0.002–0.0035 in.] for Capsule 1 and [0.003-0.004 in] for Capsule 2). In contrast, the offset azimuthal direction varied widely, especially for the offset at the bottom of the Capsule 1 holder. This is because holder movement was somewhat constrained at the top of Capsule 1 by the TC leads running through the capsule head and into the holder and by the through tubes in Capsule 2, but the Capsule 1 bottom did not have this type of constraint. (3) During later cycles, when all TCs failed, applying the maximum possible offset of 0.006 in. to the northwest direction for both the top and bottom resulted in a calculated peak fuel temperature of 1557? in Capsule 1 (i.e., a 135? increase from 1422? with zero offset on September 20, 2019 (166A)); the maximum offset of 0.0068 in. to the south for both top and bottom resulted in a calculated peak fuel temperature of 1110°C in Capsule 2 on April 20, 2020 (i.e., a 116? increase from 994? with zero offset (168A)). High peak fuel temperatures in Capsule 1 during Cycle 166A could be the cause of massive particle failure near the end of this cycle. (4) Even though the highest temperature at the tip of Type-N TCs, such as TC-1-7, slightly exceeded 1000?, the temperature along the TC wire reached as high as 1335? assuming an offset of 0.006 in. in the northwest of Capsule 1 holder near the end of Cycle 166A. This temperature significantly exceeds the temperature threshold at which TC degradation is expected to occur, ultimately contributing to considerable particle failures in Capsule 1. For eight Type-N TCs in Capsule 2, the peak TC line temperature was much lower (i.e., 1029°C for TC-2-5), assuming maximum offset of 00068 in. to the south during cycle 168A.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

AGR-5/6/7 Thermal Model with Non-uniform Gas Gaps

Fuel compact temperatures are a crucial factor in assessing the irradiation performance of tri-structural isotropic fuel particles. In the absence of direct measurement, fuel compact temperatures were calculated using a three-dimensional finite element thermal model, which is subject to simulation uncertainty. The most dominant factor in the uncertainty of calculated fuel temperatures is the gas gap uncertainty due to the nub-to-shell clearance caused by a design error of AGR-5/6/7 capsules. The thermal model was revised to examine the most probable graphite offset position for six different days during the irradiation for Capsules 1 and 2. The analysis varied the offset distance and azimuthal direction at both the top and bottom of the holder. The best-fit offset was estimated based on the minimum root mean square error of the residuals (measured minus calculated) for the operational thermocouples (TCs). From these results, the following conclusions were made: (1) The holder offsets led to slightly lower average temperatures but wider temperature variations (lower minimum and higher peak fuel temperatures) for both Capsule 1 and Capsule 2. (2) During earlier cycles (162A–164B), when numerous TCs were still operational, the best-fit offset distance varied over a specific range for both the top and bottom ([0.002–0.0035 in.] for Capsule 1 and [0.003-0.004 in] for Capsule 2). In contrast, the offset azimuthal direction varied widely, especially for the offset at the bottom of the Capsule 1 holder. This is because holder movement was somewhat constrained at the top of Capsule 1 by the TC leads running through the capsule head and into the holder and by the through tubes in Capsule 2, but the Capsule 1 bottom did not have this type of constraint. (3) During later cycles, when all TCs failed, applying the maximum possible offset of 0.006 in. to the northwest direction for both the top and bottom resulted in a calculated peak fuel temperature of 1557? in Capsule 1 (i.e., a 135? increase from 1422? with zero offset on September 20, 2019 (166A)); the maximum offset of 0.0068 in. to the south for both top and bottom resulted in a calculated peak fuel temperature of 1110°C in Capsule 2 on April 20, 2020 (i.e., a 116? increase from 994? with zero offset (168A)). High peak fuel temperatures in Capsule 1 during Cycle 166A could be the cause of massive particle failure near the end of this cycle. (4) Even though the highest temperature at the tip of Type-N TCs, such as TC-1-7, slightly exceeded 1000?, the temperature along the TC wire reached as high as 1335? assuming an offset of 0.006 in. in the northwest of Capsule 1 holder near the end of Cycle 166A. This temperature significantly exceeds the temperature threshold at which TC degradation is expected to occur, ultimately contributing to considerable particle failures in Capsule 1. For eight Type-N TCs in Capsule 2, the peak TC line temperature was much lower (i.e., 1029°C for TC-2-5), assuming maximum offset of 00068 in. to the south during cycle 168A.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Distribution, Ecology, Life History, and Conservation Status of the Berry Cave Salamander (Gyrinophilus gulolineatus)

The Berry Cave Salamander (Gyrinophilus gulolineatus) is a neotenic, stygobitic salamander endemic to eight cave systems and an isolated surface record in the Appalachian Valley and Ridge of eastern Tennessee. We conducted surveys for G. gulolineatus from 2017–2019 to assess the status of the species, locate new populations, and address knowledge gaps related to life history and population ecology required for conservation assessment. We confirmed G. gulolineatus presence at four historical sites, but we did not observe the species at any additional caves. At the three known sites with greatest abundance, visual counts per survey ranged 0–19 salamanders in 2017–2019. There was no apparent trend in abundance at Berry Cave. Visual counts declined 65% since the mid-2000s at Meads Quarry Cave and 80% since the early 1980s at Mudflats Cave. Mark-recapture studies in 160-m of cave stream at Berry Cave in 2017–2018 and 900-m of cave stream at Meads Quarry Cave in 2008 yielded population size estimates that ranged from 34–78 and 15–65 individuals, respectively. We identified 13 existing or potential threats to populations. Habitat degradation and groundwater contamination (associated with urbanization of the Knoxville metropolitan area and past mining operations) represent the most evident threats to long-term viability. Based on our conservation assessments, we recommend a rank of Endangered under IUCN Red List criteria and Critically Imperiled–Imperiled (G1G2) under NatureServe criteria. In opposition to the recent U.S. Fish & Wildlife Service decision, we advocate that, at minimum, G. gulolineatus remain a Candidate Species. Given the identified threats and these ranks, we offer several recommendations for research, conservation, and management of this rare salamander.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

JUST-R metrics for considering energy justice in early-stage energy research

We report achieving sustainable decarbonization of the energy sector requires implementing and improving energy technologies while simultaneously managing sources of social inequity in the energy system. Centering energy justice, which has "the goal of achieving equity in both the social and economic participation in the energy system, while also remediating social, economic, and health burdens on those historically harmed by the energy system," in the transition to clean energy has become an increasingly urgent priority for social scientists, policymakers, and community activists alike. However, late-stage consideration of social impacts of energy technologies may result in identifying inequities only after substantial time, money, and effort have been expended on research and development (R&D). This issue is exemplified by concerns over environmental and human health impacts related to cobalt in lithium-ion batteries, which has spurred research into alternatives only after decades of R&D and the establishment of supply chains, infrastructure, and markets for cobalt-containing chemistries. Other examples include issues with land use and resource consumption related to first-generation biofuel feedstocks as well as occupational hazards and pollution associated with photovoltaics manufacturing. In all these cases, subsequent R&D to improve technologies or processes cannot undo the effects already experienced. Incorporating energy justice from the earliest stage of R&D will enable more just technology implementation, but integrating justice considerations into early-stage research is a challenge due to a lack of tools to assess and manage them. To fill this gap, we center early-stage research to develop the Justice Underpinning Science and Technology Research (JUST-R) metrics framework - energy justice metrics specifically targeted at early-stage researchers to assess their work on an immediate timescale. By applying these metrics to a case study focused on materials for next-generation photovoltaics, we highlight potential benefits and barriers to implementing this framework in early-stage research and discuss necessary institutional and individual actions needed for researchers to effectively leverage the tool to incorporate justice-focused criteria into R&D decision making.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2022

Wabash CarbonSAFE. Final Report

This document summarizes work detailed in separate Wabash CarbonSAFE reports; the report describes the data collection efforts of the project and consolidates the geologic characterization, well testing, and storage complex modeling results for the Mt. Simon Sandstone and Potosi Dolomite, two distinct reservoirs characterized at the Wabash CarbonSAFE project site. Also presented are summaries of work to characterize the CO 2 source and infrastructure network, as well as summaries of reports analyzing stakeholder engagement options, policy, regulatory and legal considerations, and risk assessment associated with the Wabash CarbonSAFE project site. The report then presents recommendations for the next steps for site characterization, identifies data gaps for future activities, and provides an overall assessment of site potential.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2020

Realizing gapped surface states in the magnetic topological insulator Mn Bi 2 - x Sb x Te 4

The interplay between magnetism and nontrivial topology in magnetic topological insulators (MTIs) is expected to give rise to exotic topological quantum phenomena like the quantum anomalous Hall effect and the topological axion states. A key to assessing these novel properties is to realize gapped topological surface sates. MnBi 2 Te 4 possesses nontrivial band topology with an intrinsic antiferromagnetic state. However, the highly electron-doped nature of the MnBi 2 Te 4 crystals obstructs the exhibition of the surface band gap. Here, we tailor the material through Sb substitution to reveal the gapped surface states in MnBi 2-x Sb x Te 4 . By shifting the Fermi level into the bulk band gap, we access the surface states and show a band gap of 50 meV at the Dirac point from quasiparticle interference measured by scanning tunneling microscopy (STM). Surface-dominant conduction is confirmed through transport spectroscopy measured by multiprobe STM below the Néel temperature. The surface band gap is robust against the out-of-plane magnetic field despite the promotion of field-induced ferromagnetism. Finally, the realization of bulk-insulating MTIs with the large exchange gap offers a promising platform for exploring emergent topological phenomena.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2022

System and technoeconomic analysis of solar thermochemical hydrogen production

Hydrogen is a promising energy carrier that can be obtained from various feedstocks using renewable energy sources. Direct solar thermochemical hydrogen (STCH) production by water splitting can utilize the full spectrum of solar radiation and has the potential to achieve high solar energy conversion efficiencies. Currently STCH research areas focus on material discovery. This paper evaluates the performance of various STCH materials in the context of a system platform to assess techno-economic benefits and gaps in the path to STCH scale-up. Additionally, to analyze the hydrogen production cost, a concentrating solar thermal (CST) system is introduced as a platform for integrating STCH materials and accommodating generalized thermochemical processes. The thermochemical process is based on a two-step STCH cycle using metal oxide that consists of a high temperature step for metal oxide reduction, followed by an oxidation step for water splitting at a lower temperature. A preferred configuration is to have the high temperature step occurring in a directly irradiated solar receiver reactor. To this end, we conceptualized a receiver design and associated solar field layout and investigated STCH operational boundaries, component costs and sensitivity parameters on the $2/kgH 2 goal of hydrogen production. The study explored system-related variables and factors associated with scaling up. The CST platform allows more comprehensive studies that encompass aspects of STCH materials and systems such as cost, hydrogen productivity and replacement frequency, alongside other system components like heliostat field, tower, and potential receiver costs.

08 HYDROGEN↗

DOE OSTI2023

Astrovirology: how viruses enhance our understanding of life in the Universe

Abstract Viruses are the most numerically abundant biological entities on Earth. As ubiquitous replicators of molecular information and agents of community change, viruses have potent effects on the life on Earth, and may play a critical role in human spaceflight, for life-detection missions to other planetary bodies and planetary protection. However, major knowledge gaps constrain our understanding of the Earth's virosphere: (1) the role viruses play in biogeochemical cycles, (2) the origin(s) of viruses and (3) the involvement of viruses in the evolution, distribution and persistence of life. As viruses are the only replicators that span all known types of nucleic acids, an expanded experimental and theoretical toolbox built for Earth's viruses will be pivotal for detecting and understanding life on Earth and beyond. Only by filling in these knowledge and technical gaps we will obtain an inclusive assessment of how to distinguish and detect life on other planetary surfaces. Meanwhile, space exploration requires life-support systems for the needs of humans, plants and their microbial inhabitants. Viral effects on microbes and plants are essential for Earth's biosphere and human health, but virus–host interactions in spaceflight are poorly understood. Viral relationships with their hosts respond to environmental changes in complex ways which are difficult to predict by extrapolating from Earth-based proxies. These relationships should be studied in space to fully understand how spaceflight will modulate viral impacts on human health and life-support systems, including microbiomes. In this review, we address key questions that must be examined to incorporate viruses into Earth system models, life-support systems and life detection. Tackling these questions will benefit our efforts to develop planetary protection protocols and further our understanding of viruses in astrobiology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Fluid temperature predictions of geothermal borefields using load estimations via state observers

Fluid temperature predictions of geothermal borefields usually involves temporal superposition of its characteristic g-function, using load aggregation schemes to reduce computational times. Assuming that the ground has linear properties, it can be modeled as a linear state space system where the states are the aggregated loads. However, the application and accuracy of these models is compromised when the borefield is already operating and its load history is not registered or there are gaps in the data. This paper assesses the performance of state observers to estimate the borefield load history and obtain accurate fluid predictions. Results show that both Time-Varying Kalman Filter (TVKF) and Moving Horizon Estimator (MHE) provide predictions with average and maximum errors below 0.1 $^\circ C$ and 1 $^\circ C$ respectively. MHE outperforms TVKF in terms of n-step ahead output predictions and load history profile at the expenses of about 5 times more computational time.

Figueroa, Iago C.↗

DOE OSTI2023

Unrealized Critical Lanthanide Extraction from Sea Algae Mining (UNCLE SAM): Domestic production of critical minerals from seawater

The UNCLE-SAM project, under the Biotechnologies to Ensure a Robust Supply of Critical Materials for Clean Energy program, examined the biomining applications of seaweeds for sustainable, domestic production of critical mineral feedstocks. The ocean is a vast reserve of mineralogical wealth including rare earth elements (REEs) and platinum group metal (PGMs). These elements, categorized as “critical minerals”, are used in telecommunication devices, lasers, LED lighting, turbine generators, electric car motors, jet engine alloys, and many other applications. These critical elements are increasingly vital to a thriving, efficient and sustainable society. However, only a few countries in the global market currently produce and export REEs, leading to potential geopolitical supply disruptions. Marine macroalgae, often referred to as seaweeds, bioconcentrate critical minerals from seawater, including REEs and PGMs. Marine algae cultivation can generate a significant amount of biomass with minimal freshwater, fertilizer, and land requirements. In summary, the UNCLE-SAM project successfully evaluated the technological feasibility for marine macroalgal cultivation as a feedstock for critical minerals, explored the biological capacity of different seaweeds to provide economically relevant domestic mineral production, assessed processing techniques for thermal co-conversion of seaweeds into renewable fuel and mineral feedstocks, and executed techno-economic and lifecycle assessments for identifying the most critical gaps in our current understanding to move the technology into commercially relevant deployment. Further development of this technology could transform the bioproduct and REE mining industries and catalyze the development of a more sustainable future.

58 GEOSCIENCES↗

DOE OSTI2025

Circularity Futures Workshop Series: Summary Report

The aim of this report is to synthesize key feedback received from the three-part Circularity Futures workshop series held in Spring 2024. The workshop series was conducted by the National Renewable Energy Laboratory (NREL) on behalf of U.S. Department of Energy, Office Energy Efficiency and Renewable Energy (EERE), and was broken into three workshops: Workshop 1 - Circularity Analysis Needs and Priorities; Workshop 2 - Circularity Metrics and Indicators; and Workshop 3 - Circularity Data. Together, the workshops focused on identifying the existing priorities and gaps in the circularity modeling space, understanding different stakeholders' use and interpretation of circularity metrics and indicators, identifying common data gaps and data quality challenges, and assessing the robustness of available solutions. The workshop series brought a diverse group of stakeholders - including representatives from U.S. government offices, national labs, nonprofit organizations, industry, and academia - to collect first-hand feedback on needs, priorities, challenges and opportunities in the circularity modeling and analysis space. The workshop discussions highlighted numerous common needs, priorities and challenges among the interviewed groups. Several topics were frequently discussed, including: 1) Circularity as a pathway for sustainable economic growth: While circularity is generally defined in terms of resource conservation and reducing wasteful disposal of materials, participants agreed that circular strategies should serve broader economic, environmental, and social goals. It is therefore crucial for circularity analysis to look beyond waste reduction and instead evaluate a variety of impact metrics such as cost savings, job creation, air quality, and pollutant emissions. Mutli-criteria decision-making frameworks may be useful for making sense of disparate metrics and evaluating tradeoffs between impact categories.; 2) Economic and social factors are not well understood: Underdevelopment of existing end-of-life (EOL) management infrastructure, inconsistent standardization codes and policy space in reusing recycled content, and suboptimal collection and sorting strategies collectively contribute to uncertainty about the economic potential of circular pathways. The latter observation is consistent among all technologies but more emphasized for renewable energy systems. Social impacts of circularity practices are less understood and less researched than other sustainability aspects.; 3) Inconsistent methods for assessing emerging technologies: LCA and TEA results vary widely depending on the assumptions made with regards to market adoption of new technologies. Emerging technologies suffer limited availability of data needed to conduct a robust circularity analysis. Yet, understanding projected impacts of proposed nascent technology is a key need for different stakeholder groups.; and 4) Lack of temporally and geospatially explicit data: There is a need for open data that represents variations in circularity technologies over time and location. The lack thereof leads to aggregated and potentially misrepresented results in circularity analysis. Sensitivity analyses should be included to verify whether options perceived as more sustainable align with real-world practices.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2025

High-Temperature Gas Sensor Materials with Properties Predicted via First-Principles Calculations with Machine Learning Modeling and Experimental Corroboration

Understanding the temperature dependence of functional properties of sensing materials is vital for their applications in combustion environments. The electron-phonon coupling that derives the electronic structure change with temperatures is a key property of interest as it affects other sensing responses. Herein, we first assess the temperature dependence of band gap renormalization in sensing materials by employing Allen-Heine-Cardona (AHC) theory with density functional theory (DFT) simulations corroborated with experimental observation. As the AHC calculations are impractical for high-throughput screening of materials, we employ data-driven Gaussian process regression to predict the parameters employed in the O’Donnell empirical model from a set of physical features. To mitigate the reliability issues arising from the small size of the dataset, we apply a Bayesian technique to improve the generalizability of the data-driven models as well as to quantify the uncertainty associated with theoretical predictions. These models capture well the overall trend of the O’Donnell parameters with respect to a reduced feature set obtained by transforming the available physical features. Quantifying the associated uncertainty helps us understand the reliability of the predictions and, therefore, the variation of bandgap as a function of temperature for other novel materials. The predicted candidates from machine learning models are further validated by experiments and DFT calculations.

bandgap renormalization↗

DOE OSTI2023

UNrealized Critical Lanthanide Extraction from Sea Algae Mining (UNCLE SAM)

The UNCLE-SAM project, under the Biotechnologies to Ensure a Robust Supply of Critical Materials for Clean Energy program, examined the biomining applications of seaweeds for sustainable, domestic production of critical mineral feedstocks. The ocean is a vast reserve of mineralogical wealth including rare earth elements (REEs) and platinum group metal (PGMs). These elements, categorized as “critical minerals”, are used in telecommunication devices, lasers, LED lighting, turbine generators, electric car motors, jet engine alloys, and many other applications. These critical elements are increasingly vital to a thriving, efficient and sustainable society. However, only a few countries in the global market currently produce and export REEs, leading to potential geopolitical supply disruptions. Marine macroalgae, often referred to as seaweeds, bioconcentrate critical minerals from seawater, including REEs and PGMs. Marine algae cultivation can generate a significant amount of biomass with minimal freshwater, fertilizer, and land requirements. In summary, the UNCLE-SAM project successfully evaluated the technological feasibility for marine macroalgal cultivation as a feedstock for critical minerals, explored the biological capacity of different seaweeds to provide economically relevant domestic mineral production, assessed processing techniques for thermal co-conversion of seaweeds into renewable fuel and mineral feedstocks, and executed techno-economic and lifecycle assessments for identifying the most critical gaps in our current understanding to move the technology into commercially relevant deployment. Further development of this technology could transform the bioproduct and REE mining industries and catalyze the development of a more sustainable future.

09 BIOMASS FUELS↗

DOE OSTI2024

North America’s Potential for an Environmentally Sustainable Nickel, Manganese, and Cobalt Battery Value Chain

The Detroit Big Three General Motors (GMs), Ford, and Stellantis predict that electric vehicle (EV) sales will comprise 40–50% of the annual vehicle sales by 2030. Among the key components of LIBs, the LiNixMnyCo1−x−yO2 cathode, which comprises nickel, manganese, and cobalt (NMC) in various stoichiometric ratios, is widely used in EV batteries. This review reveals NMC cathodes from laboratory research. Furthermore, this study examines the environmental effect of NMC cathode production for EV batteries (including coating technologies), encompassing aspects such as energy consumption, water usage, and air emissions. Although gaps persist in NMC cathode environmental assessments (NMC111, NMC532, NMC622, and NMC811), limited life cycle assessments “(LCA)” have been conducted. Most available data originate from Asia (primarily China), accounting for 85% of the production of EV LIB cathode materials. The concept of battery passports for data collection on LIB components has been proposed to facilitate material traceability as a system for ensuring a sustainable supply chain for critical minerals. The automotive industry’s shift to electrification necessitates a sustainable supply chain from mine to vehicle end-of-life. As the critical mineral supply moves from Asia to North America, environmentally friendly industrial methods must be studied to provide this supply chain direction.

25 ENERGY STORAGE↗

DOE OSTI2021

Review of Swift Heavy Ion Irradiation Effects in CeO2

Cerium dioxide (CeO2) exhibits complex behavior when irradiated with swift heavy ions. Modifications to this material originate from the production of atomic-scale defects, which accumulate and induce changes to the microstructure, chemistry, and material properties. As such, characterizing its radiation response requires a wide range of complementary characterization techniques to elucidate the defect formation and stability over multiple length scales, such as X-ray and neutron scattering, optical spectroscopy, and electron microscopy. In this article, recent experimental efforts are reviewed in order to holistically assess the current understanding and knowledge gaps regarding the underlying physical mechanisms that dictate the response of CeO2 and related materials to irradiation with swift heavy ions. The recent application of novel experimental techniques has provided additional insight into the structural and chemical behavior of irradiation-induced defects, from the local, atomic-scale arrangement to the long-range structure. However, future work must carefully account for the influence of experimental conditions, with respect to both sample properties (e.g., grain size and impurity content) and ion-beam parameters (e.g., ion mass and energy), to facilitate a more direct comparison of experimental results.

42 ENGINEERING↗

DOE OSTI2021

Revisiting Newly Large Magellanic Cloud Age-gap Star Clusters

Recently, a noticeable number of new star clusters was identified in the outskirts of the Large Magellanic Cloud (LMC) populating the so-called star-cluster age gap, a space of time (∼4–12 Gyr) where the only known star cluster is up-to-date ESO 121-SC 03. We used Survey of the Magellanic Stellar History DR2 data sets, as well as those employed to identify these star-cluster candidates, to produce relatively deep color–magnitude diagrams (CMDs) of 17 out of 20 discovered age-gap star clusters with the aim of investigating them in detail. Our analysis relies on a thorough CMD cleaning procedure of the field-star contamination, which presents variations in its stellar density and astrophysical properties, such as luminosity and effective temperature, around the star-cluster fields. We built star-cluster CMDs from stars with membership probabilities assigned from the cleaning procedure. These CMDs and their respective spatial distribution maps favor the existence of LMC star field density fluctuations rather than age-gap star clusters, although a definitive assessment on them will be possible from further deeper photometry.

47 OTHER INSTRUMENTATION↗

NASA NTRS1993

Entry Systems Panel deliberations

The Entry Systems Panel was chaired by Don Rummler, LaRC and Dan Rasky, ARC. As requested, each panel participant prior to the workshop prepared and delivered presentations to: (1) identify technology needs; (2) assess current programs; (3) identify technology gaps; and (4) identify highest payoff areas R&D. Participants presented background on the entry systems R&D efforts and operations experiences for the Space Shuttle Orbiter. These participants represented NASA Centers involved in research (Ames Research Center), development (Johnson Space Center) and operations (Kennedy Space Center) and the Shuttle Orbiter prime contractor. The presentations lead to the discovery of several lessons learned.

Rasky, Daniel J.↗