Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GRAIN ORIENTATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

INTERFACE RESIDUAL STRESSES IN DENTAL ZIRCONIA USING LAUE MICRO-DIFFRACTION

Due to their aesthetic value and high compressive strength, dentists have recently employed ceramics for restoration materials. Among the ceramic materials, zirconia provides high toughness and crack resistant characteristics. Residual stresses develop in processing due to factors including grain anisotropy and thermal coefficient mismatch. In the present study, polychromatic X-ray (Laue) micro-diffraction provided grain orientation and residual stresses on a clinically relevant zirconia model ceramic disk. A 0.5 mm x 0.024 mm region on zirconia was examined on a 500 nm scale for residual stresses using a focused poly-chromatic synchrotron X-ray beam. Large stresses ranging from - to + 1GPa were observed at some grains. On average, the method suggests a relatively small compressive stress at the surface between 47 and 75 MPa depending on direction.

36 MATERIALS SCIENCE↗

Fast Grain Mapping with Sub-Nanometer Resolution Using 4D-STEM with Grain Classification by Principal Component Analysis and Non-Negative Matrix Factorization

High-throughput grain mapping with sub-nanometer spatial resolution is demonstrated using scanning nanobeam electron diffraction (also known as 4D scanning transmission electron microscopy, or 4D-STEM) combined with high-speed direct-electron detection. An electron probe size down to 0.5 nm in diameter is used and the sample investigated is a gold–palladium nanoparticle catalyst. Computational analysis of the 4D-STEM data sets is performed using a disk registration algorithm to identify the diffraction peaks followed by feature learning to map the individual grains. Two unsupervised feature learning techniques are compared: principal component analysis (PCA) and non-negative matrix factorization (NNMF). The characteristics of the PCA versus NNMF output are compared and the potential of the 4D-STEM approach for statistical analysis of grain orientations at high spatial resolution is discussed.

47 OTHER INSTRUMENTATION↗

Characterization of twin boundaries in an Fe–17.5Mn–0.56C twinning induced plasticity steel

A twinning-induced plasticity steel of composition Fe–17.5 wt.% Mn–0.56 wt.% C–1.39 wt.% Al–0.24 wt.% Si was analyzed for the purpose of characterizing the relationship between tensile strain and deformation twinning. Tensile samples achieved a maximum of 0.46 true strain at failure, and a maximum ultimate tensile strength of 1599 MPa. Electron backscatter diffraction (EBSD) analysis showed that the grain orientation rotated heavily to < 111 > parallel to the tensile axis above 0.3 true strain. Sigma 3 misorientations, as identified by EBSD orientation measurements, and using the image quality maps were used to quantify the number of twins present in the scanned areas of the samples. The image quality method yielded a distinct positive correlation between the twin area density and deformation, but the orientation measurements were unreliable in quantifying twin density in these structures. Quantitative analysis of the twin fraction is limited from orientation information because of the poor spatial resolution of EBSD in relation to the twin thickness. The EBSD orientation maps created for a thin foil sample showed some improvement in the resolution of the twins, but not enough to be significant. Measurements of the twins in the transmission electron microscopy micrographs yielded an average thickness of 23 nm, which is near the resolution capabilities of EBSD on this material for the instrumentation used. Electron channeling contrast imaging performed on one bulk tensile specimen of 0.34 true strain, using a method of controlled diffraction, yielded several images of twinning, dislocation structures and strain fields. A twin thickness of 66 nm was measured by the same method used for the transmission electron microscopy measurement. It is apparent that the results obtain by electron channeling contrast imaging were better than those by EBSD but did not capture all information on the twin boundaries such as was observed by transmission electron microscopy. - Highlights: • Performed tensile tests to assess mechanical performance of TWIP alloy • Analyzed tensile specimens using EBSD, TEM, and ECCI • EBSD showed that most twinning occurred at or near the < 111 >//TA orientation. • EBSD, TEM and ECCI were used to measure average twin density. • Compared spatial resolution of EBSD, ECCI and TEM for the instrumentation used.

36 MATERIALS SCIENCE↗

Abnormal crystal growth in CH 3 NH 3 PbI 3-x Cl x using a multi-cycle solution coating process

Recently, the efficiency of organolead trihalide perovskite solar cells has improved greatly because of improved material qualities with longer carrier diffusion lengths. Mixing chlorine in the precursor for mixed halide films has been reported to dramatically enhance the diffusion lengths of mixed halide perovskite films, mainly as a result of a much longer carrier recombination lifetime. Here we report that adding Cl containing precursor for mixed halide perovskite formation can induce the abnormal grain growth behavior that yields well-oriented grains accompanied by the appearance of some very large size grains. The abnormal grain growth becomes prominent only after multi-cycle coating of MAI : MACl blend precursor. The large grain size is found mainly to contribute to a longer carrier charge recombination lifetime, and thus increases the device efficiency to 18.9%, but without significantly impacting the carrier transport property. As a result, the strong correlation identified between material process and morphology provides guidelines for future material optimization and device efficiency enhancement.

36 MATERIALS SCIENCE↗

Grain boundary plane orientation fundamental zones and structure-property relationships

Grain boundary plane orientation is a profoundly important determinant of character in polycrystalline materials that is not well understood. This work demonstrates how boundary plane orientation fundamental zones, which capture the natural crystallographic symmetries of a grain boundary, can be used to establish structure-property relationships. Using the fundamental zone representation, trends in computed energy, excess volume at the grain boundary, and temperature-dependent mobility naturally emerge and show a strong dependence on the boundary plane orientation. Analysis of common misorientation axes even suggests broader trends of grain boundary energy as a function of misorientation angle and plane orientation. Due to the strong structure-property relationships that naturally emerge from this work, boundary plane fundamental zones are expected to simplify analysis of both computational and experimental data. This standardized representation has the potential to significantly accelerate research in the topologically complex and vast five-dimensional phase space of grain boundaries.

36 MATERIALS SCIENCE↗

Evolution of Crystallinity and Texturing on 120 MeV Au Ion Irradiation on NiO Thin Films

NiO thin films grown on Si(100) substrate by electron beam evaporation and sintered at 500 deg. C and 700 deg. C were irradiated with 120 MeV {sup 197}Au{sup 9+} ions. The FCC structure of the sintered films was retained up to the highest fluence (3 x l0{sup 13} ions.cm{sup -2}) of irradiation. As against the expected amorphization due to ion irradiation when electronic energy loss exceeds certain threshold value, we observe an improvement of crystallinity and grain orientation at certain fluences of irradiation.

36 MATERIALS SCIENCE↗

Thermoelectric conversion via laser-induced voltage in highly textured polycrystalline Na{sub x}CoO{sub 2} ceramic

We have studied and analyzed the laser-induced voltage effect in highly c-axis-oriented polycrystalline Na{sub x}CoO{sub 2}. The textured and layered stacking Na{sub x}CoO{sub 2} (x {approx} 0.7) bulks were prepared by a solid-state reaction process. Under the irradiation on Na{sub 0.67}CoO{sub 2} bulk surface with pulsed laser ({lambda} = 248 nm), the induced voltage signals were observed on the inclined surface with rise time 30 ns-43 ns and peak voltage 200 mV-500 mV; the voltage peak values show a linear dependence of laser energy densities. The crystal grains orientation plays a critical role in voltage peak value whether in film or texture bulk. The transverse voltage signal brings the information of thermoelectric anisotropy. In Na{sub x}CoO{sub 2} band structure, the Fermi surface is different in the ab plane and along the c axis, leading to anisotropy of Seebeck coefficient. Additionally, the artificial structure of the inclined surface for highly textured bulk enables us to obtain a transverse voltage on inclined surface. These results demonstrated the layered textured bulk has potential applications in waste-heat conversion via transverse thermoelectric effect.

36 MATERIALS SCIENCE↗

High-resolution in-situ characterization of the surface evolution of a polycrystalline NiTi SMA-alloy under pseudoelastic deformation

The current study addresses the relation between grain orientations, local strain concentrations and resulting topographical changes in NiTi on the meso- and microscale by means of a comprehensive experimental in-situ approach, involving electron backscatter diffraction, confocal laser scanning microscopy and digital image correlation. The findings presented herein clearly show that this approach is capable of identifying the relationships between the microstructural features and phase transformation-induced topographical evolutions, which govern defect formation in thin protective coatings. - Research Highlights: {yields} High local strain gradients are observed between highly misoriented grains. {yields} Pronounced surface alterations emerged across these boundaries. {yields} Roughness evolution induced highly localized strains in the vicinity of grain boundaries. {yields} EBSD at {epsilon} = 5.5% proved the existence of intergranular constraints.

36 MATERIALS SCIENCE↗

Surface Film Formation on Al-V Alloys with Far-From-Equilibrium Microstructure

Nanocrystalline supersaturated Al-V alloys produced by high-energy ball milling have been reported to exhibit enhanced corrosion resistance and mechanical properties compared to commercial Al alloys. Corrosion of passive alloys such as Al-V alloy relies on the characteristics of the surface film, which is studied using scanning/transmission electron microscopy and time-of-flight secondary ion mass spectrometry. The effect of microstructure and composition on the surface film has been investigated after different immersion periods (30 min, 2 h, and 1 day) in 0.1 M NaCl. The surface film was complex and composed of oxidized Al and V. The heterogeneous surface film was observed due to the presence of secondary phases and initiation of localized corrosion. The void formation was observed beneath the surface film that would potentially cause pitting corrosion. The generation of nano-sized voids was dependent on grain orientation. Compared to pure Al, the chloride penetration is suppressed in Al-V alloys. The effect of composition and microstructure on surface film formation and attendant corrosion behavior is discussed herein.

36 MATERIALS SCIENCE↗

Enhanced electromechanical coupling in Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-PbTiO{sub 3} <001>{sub C} radially textured cylinders

We demonstrate Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-PbTiO{sub 3} cylinders with ∼98% <100>{sub C} texture along the radial direction. A giant enhancement in the magnitude of electromechanical coupling factor (k{sub 31} = k{sub h} = 0.60, and k{sub l} = 0.7) was obtained for textured cylinder, and d{sub 31} × g{sub 31} was measured to be 6766 × 10{sup −15} m{sup 2}/N which is 3–6 times higher than that of commercial Pb(Zr,Ti)O{sub 3} compositions. The crystallographic grain orientation in the textured cylinder was visualized by electron backscatter diffraction, and the domain structure was characterized by piezoresponse force microscopy. Using these results, we explain the mechanism for this enhanced performance of radially textured piezoelectrics.

36 MATERIALS SCIENCE↗

Effects of Changing Hot Rolling Direction on Microstructure, Texture and Mechanical Properties of Cu-2.7Be Sheets

A hot rolling scheme (cross-rolling and unidirectional rolling) was adopted to process Cu-2.7Be sheets used as multiplier dynodes in photomultiplier. The effects of changing rolling direction on microstructure, texture and mechanical properties were studied by a combination of XRD, EBSD and TEM. It was found that higher copper-type texture and lower brass texture intensity were obtained in the ultimately cross-rolling (CR) sheet compared with the unidirectional rolling (UR) sheet.The EBSD results indicated that the grain orientation from mainly 〈101〉 for UR sample turns to random for CR sample. Great enhancements in YS and UTS after unidirectional rolling were attributed to the massive and polygonal γ precipitates. The CR sample exhibited lower anisotropy, because of the increase of S and γ precipitates with spherical and tiny shape.

36 MATERIALS SCIENCE↗

Microstructural Characterisation of Giant Magnetoresistive Co/Cu Multilayers

Antiferromagnetically-coupled Co/Cu multilayers prepared by magnetron sputtering exhibit pronounced giant magnetoresistance (GMR) effect at room temperature. Using both diffraction and imaging techniques, we studied the in-plane and out-of-plane crystallographic and layering microstructural features of these multilayers. Dominant characteristic features associated with the multilayers, such as lateral and vertical columnar grain orientations as well as layer undulations and regularity, were identified. By deliberately introducing microstructural changes to the materials system using buffer layer and heat treatment, detailed microstructural analysis have provided an insight into the dependence of GMR on microstructures of the multilayers.

36 MATERIALS SCIENCE↗

In-situ neutron diffraction investigation on twinning/detwinning activities during tension-compression load reversal in a twinning induced plasticity steel

The tension-compression type of load reversal produces an asymmetric cyclic tension-compression behavior and varied yielding stresses in the subsequent monotonic tension and compression in a twinning induced plasticity steel. The micromechanical behavior was elucidated via the evolutions of the stacking fault probability and the grain orientation density captured by in-situ neutron diffraction. The latter indicates more profound detwinning activities in a reversal from tension to compression than those from compression to tension and more twinning involves in monotonic tension than in compression. In conclusion, this is confirmed by the calculated twinning activities in monotonic tension and compression using the visco-plastic self-consistent model.

TWIP↗

Field induced domain switching as the origin of anomalous lattice strain along non-polar direction in rhombohedral BiScO{sub 3}-PbTiO{sub 3} close to the morphotropic phase boundary

The lattice strain and domain switching behavior of xBiScO{sub 3}–(1-x)PbTiO{sub 3} (x = 0.40) was investigated as a function of cyclic field and grain orientation by in situ X-ray diffraction during application of electric fields. The electric field induced 200 lattice strain was measured to be five times larger than the 111 lattice strain in pseudorhombohedral xBiScO{sub 3}–(1-x)PbTiO{sub 3} (x = 0.40). It is shown that the anomalous 200 lattice strain is not an intrinsic phenomenon, but arises primarily due to stress associated with the reorientation of the 111 domains in dense polycrystalline ceramic.

36 MATERIALS SCIENCE↗

Corrosion Behavior of AZ31 Magnesium Alloy Produced by Continuous Variable Cross Section Direct Extrusion

In order to study the corrosion behavior of magnesium alloys of high performance in the simulated seawater by continuous variable cross section direct extrusion (CVCDE), an electrochemical method and weight loss method were used to study the difference between AZ31 magnesium alloys produced by CVCDE with different numbers of interim dies to examine the electrochemical corrosion behavior and corrosion rate at 3.5 wt.% NaCl solution in this paper. Scanning electron microscopy and x-ray diffraction were used to analyze the morphology of corrosion surfaces and the composition of the corrosion products of samples soaked for different times. The results show that after CVCDE with different numbers of interim dies, the size of the microstructure is refined gradually, and the grain orientation is also different; with the increase in the number of interim dies, the thermodynamic corrosion tendencies are different, and the corrosion resistance of samples extruded by conventional extrusion is relatively good; the charge transfer and material transfer process are the two main factors affecting the corrosion rate, which determines the direction of the electrochemical reaction; the corrosion form of the sample extruded by CVCDE is the local corrosion which is the filiform corrosion and pitting corrosion, and the corrosion product is mainly water-insoluble Mg(OH){sub 2}.

36 MATERIALS SCIENCE↗

Room temperature creep behavior of Ti–Nb–Ta–Zr–O alloy

The room temperature creep behavior and deformation mechanisms of a Ti–Nb–Ta–Zr–O alloy, which is also called “gum metal”, were investigated with the nanoindentation creep and conventional creep tests. The microstructure was observed with electron backscattered diffraction analysis (EBSD) and transmission electron microscopy (TEM). The results show that the creep stress exponent of the alloy is sensitive to cold deformation history of the alloy. The alloy which was cold swaged by 85% shows high creep resistance and the stress exponent is approximately equal to 1. Microstructural observation shows that creep process of the alloy without cold deformation is controlled by dislocation mechanism. The stress-induced α' martensitic phase transformation also occurs. The EBSD results show that the grain orientation changes after the creep tests, and thus, the creep of the cold-worked alloy is dominated by the shear deformation of giant faults without direct assistance from dislocations. - Highlights: •Nanoindentation was used to investigate room temperature creep behavior of gum metal. •The creep stress exponent of gum metal is sensitive to the cold deformation history. •The creep stress exponent of cold worked gum metal is approximately equal to 1. •The creep of the cold-worked gum metal is governed by the shear deformation of giant faults.

36 MATERIALS SCIENCE↗

Mixed oxides of sodium, antimony (5+) and divalent metals (Ni, Co, Zn or Mg)

A family of alpha-NaFeO{sub 2}-type oxides Na{sub x}M{sub (1+x)/3}Sb{sub (2-x)/3}O{sub 2} (M=Ni, Co, Zn, Mg; x{approx}0.8 or 0.9) has been prepared by solid state reactions and characterized by powder XRD. At x=1, ordering occurs with tripling the unit cells and formula units. The powder patterns for Na{sub 3}M{sub 2}SbO{sub 6} (M=Ni, Co) comply with both trigonal P3{sub 1}12 cell and monoclinic C2/m cell. The Ni compound exhibits also a series of extremely weak reflections (I<0.3%) that need doubling of the c axis, and the final cell is C2/c, a=5.3048(3), b=9.1879(4), c=10.8356(7), beta=99.390(5). These ambiguities are explained by stacking faults. The compounds absorb atmospheric moisture with c-axis expansion up to 29%. A delafossite-related superlattice Ag{sub 3}Co{sub 2}SbO{sub 6} has been prepared by ion exchange and refined: P3{sub 1}12, a=5.3842(2), c=18.6613(10). Ionic conductivity of the Na{sub 0.8}Ni{sub 0.6}Sb{sub 0.4}O{sub 2} ceramics, 0.4 S/m at 300 deg. C, is greater than reported previously, presumably owing to the grain orientation produced by hot pressing. - Graphical abstract: It is shown that the powder patterns for Na{sub 3}M{sub 2}SbO{sub 6} (M=Ni and Co) may be equally well described by a trigonal P3{sub 1}12 cell and a monoclinic C2/m cell. In addition, the Ni compound exhibits a series of extremely weak reflections (I<0.3%) that need doubling of the monoclinic c axis, and the final cell is C2/c.

36 MATERIALS SCIENCE↗

Synchrotron-based measurement of the impact of thermal cycling on the evolution of stresses in Cu through-silicon vias

One of the main causes of failure during the lifetime of microelectronics devices is their exposure to fluctuating temperatures. In this work, synchrotron-based X-ray micro-diffraction is used to study the evolution of stresses in copper through-silicon via (TSV) interconnects, “as-received” and after 1000 thermal cycles. For both test conditions, significant fluctuations in the measured normal and shear stresses with depth are attributed to variations in the Cu grain orientation. Nevertheless, the mean hydrostatic stresses in the “as-received” Cu TSV were very low, at (16 ± 44) MPa, most likely due to room temperature stress relaxation. In contrast, the mean hydrostatic stresses along the entire length of the Cu TSV that had undergone 1000 thermal cycles (123 ± 37) MPa were found to be eight times greater, which was attributed to increased strain-hardening. The evolution in stresses with thermal cycling is a clear indication that the impact of Cu TSVs on front-end-of-line (FEOL) device performance will change through the lifetime of the 3D stacked dies, and ought to be accounted for during FEOL keep-out-zone design rules development.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗