SEARCH · Engineering Papers
Results for “Fuel.”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Two trillion gallons: Fuel savings from fuel economy improvements to US light-duty vehicles, 1975–2018
Since 1975, the fuel economy of new light-duty vehicles sold in the U.S. has almost doubled. Fuel economy improvements on laboratory tests gradually became real improvements on the road as newer, more efficient vehicles replaced older less efficient ones. Fleet-wide fuel economy gains produced large fuel savings. In this paper, we show that fuel economy gains measured on laboratory test cycles, adjusted for on-road conditions and weighted by the distribution of vehicles by age and their relative use, closely match estimates by the Federal Highway Administration based primarily on traffic counts and motor fuel tax records. Furthermore, adjusting for the rebound effect of fuel economy on vehicle miles traveled, we estimate the fuel savings, CO 2 emissions reductions and dollars saved on fuel due to fuel economy improvements over the past 43 years. Through the end of 2018, estimated cumulative fuel savings amount to approximately 2 trillion gallons of gasoline. We estimate that roughly one-fifth of the savings can be attributed to gasoline price increases over the period and four-fifths to fuel economy and greenhouse gas (ghg) standards.
Core materials development for the fuel cycle R&D program
The Fuel Cycle Research and Development program is investigating methods of burning minor actinides in a transmutation fuel. One of the challenges of achieving this goal is to develop fuels capable of reaching extreme burnup levels (e.g. 40%). To achieve such high burnup levels’ fast reactor core materials (cladding and duct) must be able to withstand very high doses (>300 dpa design goal) while in contact with the coolant and the fuel. Thus, these materials must withstand radiation effects that promote low temperature embrittlement, radiation induced segregation, high temperature helium embrittlement, swelling, accelerated creep, corrosion with the coolant, and chemical interaction with the fuel (FCCI). To develop and qualify materials to a total fluence greater than 200 dpa requires development of advanced alloys and irradiations in fast reactors to test these alloys. Test specimens of ferritic/martensitic alloys (T91/HT-9) previously irradiated in the FFTF reactor up to 210 dpa at a temperature range of 350– 750 °C are presently being tested. This includes analysis of a duct made of HT-9 after irradiation to a total dose of 155 dpa at temperatures from 370 to 510 °C. Compact tension, charpy and tensile specimens have been machined from this duct and mechanical testing as well as SANS and Mossbauer spectroscopy are currently being performed. Initial results from compression testing and Charpy testing reveal a strong increase in yield stress (~400 MPa) and a large increase in DBTT (up to 230 °C) for specimens irradiated at 383 °C to a dose of 28 dpa. Less hardening and a smaller increase in DBTT was observed for specimens irradiated at higher temperatures up to 500 °C. Advanced radiation tolerant materials are also being developed to enable the desired extreme fuel burnup levels. Specifically, coatings are being developed to minimize FCCI, and research is underway to fabricate large heats of radiation tolerant oxide dispersion steels with homogeneous oxide dispersions.
The Effect of Transient Fuel Staging on Self-Excited Instabilities in a Multi-Nozzle Model Gas Turbine Combustor
Combustion instability in gas turbines can be mitigated using active techniques or passive techniques, but passive techniques are almost exclusively used in industrial settings. While fuel staging, a common passive technique, is effective in reducing the amplitude of self-excited instabilities in gas turbine combustors at steady-state conditions, the effect of transients in fuel staging on self-excited instabilities is not well understood. This paper examines the effect of fuel staging transients on a laboratory-scale five-nozzle can combustor undergoing self-excited instabilities. The five nozzles are arranged in a four-around-one configuration and fuel staging is accomplished by increasing the center nozzle equivalence ratio. When the global equivalence ratio is φ = 0.70 and all nozzles are fueled equally, the combustor undergoes self-excited oscillations. These oscillations are suppressed when the center nozzle equivalence ratio is increased to φ = 0.80 or φ = 0.85. Two transient staging schedules are used, resulting in transitions from unstable to stable operation, and vice-versa. It is found that the characteristic instability decay times are dependent on the amount of fuel staging in the center nozzle. It is also found that the decay time constants differ from the growth time constants, indicating hysteresis in stability transition points. High speed CH* chemiluminescence images in combination with dynamic pressure measurements are used to determine the instantaneous phase difference between the heat release rate fluctuation and the combustor pressure fluctuation throughout the combustor. This analysis shows that the instability onset process is different from the instability decay process.
Comprehensive Fuel Performance Model Development and Simulation for TRISO Fuel
High Temperature Gas Reactor (HTGR), widely recognized as one of the top candidates for the Next Generation Nuclear Power-plant (NGNP) fleet, has received ever-increasing interest due to its superior safety and many other desirable features. TRISO fuel particles are the basic form of the fuel used in both pebble-bed and prismatic reactors. Since they are a key component of the HTGR core design, the success of the reactor depends on the safety and quality of the TRISO particles. During operation, a TRISO particle undergoes complex thermo-mechanical processes. Fission gases accumulate inside the kernel and the buffer layer, and lead to buildup of internal pressure. Uneven thermal conditions lead to asymmetric thermal expansion. The pyrolytic carbon, in both the IPyC and OPyC layers, is known to experience dimensional change (shrinkage or swelling) under fast neutron irradiation. In the mean time, both the IPyC and OPyC layers creep as a function of stress and fast neutron fluence. Macro cracks in the IPyC layer, corrosion in the SiC layer due to chemical attack, and debonding at the interface between IPyC and SiC, have been observed in post-irradiation examinations. All these processes further complicate the stress states in a TRISO particle, and might lead to failure of a single coating layer or the particle as a whole. It is very difficult to duplicate the actual environment that a particle is exposed to in experiments. It is even more difficult to isolate one process from another, thus making it nearly impossible to evaluate the impacts that a particular process has on the fuel particle by conducting experiments. The problem can however at least partially be addressed by modeling and simulation. Hence, multi-dimensional, multi-physics and comprehensive models are greatly needed to simulate and evaluate the performance of a TRISO particle under normal and accidental conditions. Existing models are inadequate as they are usually one-dimensional models that over-simplified these processes or do not include all the main physics. The goal of this thesis is to develop a comprehensive, multi-dimensional and multi-physics model to simulate and evaluate TRISO fuel performance. It includes all the main processes taking place in the fuel particle. Three equally important components of this modeling exercise are: 1) 3D heat transfer and temperature distribution analysis; 2) 3D neutronics, heat generation, and fission gas generation and release analysis; 3) 3D stress analysis and failure prediction of the TRISO particle. The 3D thermal model consists of the solution of the heat conduction equation using the finite difference technique. The temperature calculated using this model is compared to analytical solutions and to the results reported in literature. Good agreements are observed. Thermal models are developed to calculate temperature distribution in a pebble under different power and asymmetric convective boundary conditions caused by, for example, contacts with other pebbles. Three-dimensional temperature distribution in a TRISO particle is also calculated under various conditions such as in the presence of an off-center gas bubble. Three-dimensional neutronics models are developed using MCNP5/X. Burnup calculations are performed to track the number densities of a few important isotopes and to calculate gas production. The fractional gas release on both intra- and inter-granular level are calculated using the White and Tucker’s model. The gas pressure inside the buffer layer is also quantified. Finally, 3D axisymmetric stress models are developed using an open-source finite element code, FEAP. Modifications are introduced to FEAP to include PyC shrinkage and creep, etc. The modified code is benchmarked against Miller’s results, and good agreements are observed. A number of variables are studied to evaluate their impacts on stresses and failure probabilities. These variables include creep constant, creep Poisson’s ratio, irradiation temperature, BAF, layer thickness, etc. Some transient thermal conditions such as power surge, and defective cases such as a radial crack in IPyC, debonding and corrosion to SiC, are also studied. Among all, a few variables/conditions have significant impacts on stresses and failure probabilities, namely: shrinkage strain, creep constant, creep Poisson’s ratio, particle size, irradiation temperature, BAF and cracked IPyC. Order of magnitude of stresses resulting from temperature changes, pressure buildup due to gas generation, and due to PyC shrinkage/creep show that in the case of TRISO particle (when using specific empirical constants or existing dataset found in literature to calculate shrinkage/creep strains), stresses due to temperature changes and internal gas pressure are orders of magnitude lower than those resulting from shrinkage/creep. Failure probabilities of both IPyC and SiC are also calculated. The failure probability of IPyC under most conditions borderlines with the design requirement (1E-4) except under low irradiation temperature. The failure probability of SiC under normal conditions is minimal because it is always under compression; except when there is a radial crack in IPyC, in which case the stress in part of SiC becomes tensile and the failure probability is higher than 1E-4, and increases at higher burnup. The comprehensive fuel performance model developed in this work and implemented in a suite of computer codes simulates the thermo-mechanical behavior of a TRISO fuel particle under irradiation. This work leads to a better understanding of TRISO fuel particle evolution over its lifetime, and provides insights in how to improve the safety and reliability of TRISO fuel. The models developed here can be useful for other purposes related to TRISO fuel or for fuel performance evaluation of other forms of nuclear fuels. (author)
Preliminary Design Study of Medium Sized Gas Cooled Fast Reactor with Natural Uranium as Fuel Cycle Input
In this study a feasibility design study of medium sized (1000 MWt) gas cooled fast reactors which can utilize natural uranium as fuel cycle input has been conducted. Gas Cooled Fast Reactor (GFR) is among six types of Generation IV Nuclear Power Plants. GFR with its hard neuron spectrum is superior for closed fuel cycle, and its ability to be operated in high temperature (850° C) makes various options of utilizations become possible. To obtain the capability of consuming natural uranium as fuel cycle input, modified CANDLE burn‐up scheme[1–6] is adopted this GFR system by dividing the core into 10 parts of equal volume axially. Due to the limitation of thermal hydraulic aspects, the average power density of the proposed design is selected about 70 W/cc. As an optimization results, a design of 1000 MWt reactors which can be operated 10 years without refueling and fuel shuffling and just need natural uranium as fuel cycle input is discussed. The average discharge burn‐up is about 280 GWd/ton HM. Enough margin for criticality was obtained for this reactor.
Fuel-Cladding Eutectic Study of Legacy Fast Flux Test Facility (FFTF) MFF HT9/U-10Zr Metallic Fuel
This report presents the first systematic investigation of fuel-cladding eutectic interaction (FCEI) in irradiated HT9/U-10Zr metallic fuel from the Fast Flux Test Facility (FFTF) Materials Fuels Form (MFF) program, using differential scanning calorimetry (DSC) coupled with scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Two irradiated fuel cross-sections, MNT07H (9.5 at% burnup, x/L = 0.78) and MNT08H (7.0 at% burnup, x/L = 0.93), were subjected to three successive isothermal annealing rounds (R1–R3) at 820°C for 20 minutes each, yielding a cumulative transient duration of one hour. This study directly addresses a recognized gap in the existing FCEI database, which previously lacked irradiated HT9/U-10Zr data at burnup levels above 8 at%. Two principal findings emerge from the study. First, for both samples, FCEI remained spatially confined within the pre-existing fuel-cladding chemical interaction (FCCI) zone boundaries after R3, with no measurable eutectic penetration into unaffected cladding beyond the original FCCI layer. This self-limiting behavior is consistent with historical Fuel Behavior Test Apparatus (FBTA) results and is attributed to the near-eutectic phase composition of the FCCI zone, which rapidly absorb the available eutectic-forming constituents and then stall penetration once the FCCI zone is consumed. A comparison with unirradiated surrogate data further supports this mechanism: whereas a U–34 at.% Fe sample would be expected to show ~176 µm of iron penetration under comparable conditions, the irradiated samples exhibited only ~20 µm, a discrepancy attributed to irradiation-induced interfacial porosity and pre-existing FCCI composition gradients. Second, for MNT08H, FCEI was observed exclusively on the half of the cladding circumference where pre-existing steady-state FCCI was present, with no detectable FCEI on the opposite half. Three hypotheses are proposed to explain this asymmetry: the inhibiting role of a zirconium-rich rind at the fuel-cladding interface; the chemical sequestration of iron by redistributed zirconium within the fuel matrix; and the persistence of fuel-cladding gaps on the FCEI-free half that preclude direct contact. All three hypotheses require further experimental investigation. The results extend the empirical FCEI database into higher-burnup territory and demonstrate the viability of DSC-based testing as a substitute for the no-longer-available FBTA apparatus. Future work will include additional cross-section testing, compilation of the full FCEI dataset, model evaluation, and DSC testing of ternary fuel compositions to broaden the experimental basis for safety assessment of sodium-cooled fast reactor systems.
Developing custom fire behavior fuel models from ecologically complex fuel structures for upper Atlantic Coastal Plain forests.
Currently geospatial fire behavior analyses are performed with an array of fire behavior modeling systems such as FARSITE, FlamMap, and the Large Fire Simulation System. These systems currently require standard or customized surface fire behavior fuel models as inputs that are often assigned through remote sensing information. The ability to handle hundreds or thousands of measured surface fuelbeds representing the fine scale variation in fire behavior on the landscape is constrained in terms of creating compatible custom fire behavior fuel models. In this study, we demonstrate an objective method for taking ecologically complex fuelbeds from inventory observations and converting those into a set of custom fuel models that can be mapped to the original landscape. We use an original set of 629 fuel inventory plots measured on an 80,000 ha contiguous landscape in the upper Atlantic Coastal Plain of the southeastern United States. From models linking stand conditions to component fuel loads, we impute fuelbeds for over 6000 stands. These imputed fuelbeds were then converted to fire behavior parameters under extreme fuel moisture and wind conditions (97th percentile) using the fuel characteristic classification system (FCCS) to estimate surface fire rate of spread, surface fire flame length, shrub layer reaction intensity (heat load), non-woody layer reaction intensity, woody layer reaction intensity, and litter-lichen-moss layer reaction intensity. We performed hierarchical cluster analysis of the stands based on the values of the fire behavior parameters. The resulting 7 clusters were the basis for the development of 7 custom fire behavior fuel models from the cluster centroids that were calibrated against the FCCS point data for wind and fuel moisture. The latter process resulted in calibration against flame length as it was difficult to obtain a simultaneous calibration against both rate of spread and flame length. The clusters based on FCCS fire behavior parameters represent reasonably identifiable stand conditions, being: (1) pine dominated stands with more litter and down woody debriscomponents than other stands, (2) hardwood and pine stands with no shrubs, (3) hardwood dominated stands with low shrub and high non-woody biomass and high down woody debris, (4) stands with high grass and forb (i.e., non-woody) biomass as well as substantial shrub biomass, (5) stands with both high shrub and litter biomass, (6) pine-mixed hardwood stands with moderate litter biomass and low shrub biomass, and (7) baldcypress-tupelo stands. Models representing these stand clusters generated flame lengths from 0.6 to 2.3 musing a 30 km h{sub 1} wind speed and fireline intensities of 100-1500 kW m{sub 1} that are typical within the range of experience on this landscape. The fuel models ranked 1 < 2 < 7 < 5 < 4 < 3 < 6 in terms of both flame length and fireline intensity. The method allows for ecologically complex data to be utilized in order to create a landscape representative of measured fuel conditions and to create models that interface with geospatial fire models.
Irradiated microstructure of U-10Mo monolithic fuel plate at very high fission density
Not Available
Validation of the BISON 3D Fuel Performance Code: Temperature Comparisons for Concentrically and Eccentrically Located Fuel Pellets
BISON is a modern finite-element based nuclear fuel performance code that has been under development at the Idaho National Laboratory (USA) since 2009. The code is applicable to both steady and transient fuel behaviour and is used to analyse either 2D axisymmetric or 3D geometries. BISON has been applied to a variety of fuel forms including LWR fuel rods, TRISO-coated fuel particles, and metallic fuel in both rod and plate geometries. Code validation is currently in progress, principally by comparison to instrumented LWR fuel rods. Halden IFA experiments constitute a large percentage of the current BISON validation base. The validation emphasis here is centreline temperatures at the beginning of fuel life, with comparisons made to seven rods from the IFA-431 and 432 assemblies. The principal focus is IFA-431 Rod 4, which included concentric and eccentrically located fuel pellets. This experiment provides an opportunity to explore 3D thermomechanical behaviour and assess the 3D simulation capabilities of BISON. Analysis results agree with experimental results showing lower fuel centreline temperatures for eccentric fuel with the peak temperature shifted from the centreline. The comparison confirms with modern 3D analysis tools that the measured temperature difference between concentric and eccentric pellets is not an artefact and provides a quantitative explanation for the difference.
A burnup credit approach irradiated fast-neutron reactor fuels/ nuclides of interest and fuel storage application - 14248
The concept of taking into account the reduction of the reactivity of nuclear used fuel due to their burnup is referred to as 'Burnup Credit' (BUC). Economic incentives offered by the implementation of a BUC methodology in criticality analyses of Light Water Reactor (LWR) used fuel facilities are nowadays well-demonstrated. The current prospect of reprocessing the fissile and fertile subassemblies of the PHENIX reactor in France, and the development of the 4.-Generation Fast-neutron Reactors (FR) enable research projects in relevant fuel cycle operations. Under these circumstances, the CEA and AREVA-NC have decided to study a burnup credit approach for irradiated fuels of the PHENIX reactor. This paper focuses on a preliminary investigation on the use of burnup credit for used FR fuel operations. The first step consists in analyzing and selecting the nuclides of interest for burnup calculation, on the basis of the 27 BUC nuclides (12 actinides and 15 fissions products) chosen for LWR-MOx fuels [1]. These nuclides are then involved in a criticality calculation (a used fuel pool) to highlight the interest of a BUC approach. This study highlights the interest of a burnup credit approach for FR fuels and shows that the highest contribution to reactivity loss is due to only one fission product: the {sup 149}Sm. The opportunity to take account of only one fission product is highly promising and will considerably simplify the way to determine a penalizing fuel inventory. Moreover, it is to notice that results for different configurations may differ from those obtained for a fuel storage application. Thus, specific analyses have to be carried out in order to study the applicability of the conclusions of this paper. (authors)
Influence of pilot-fuel mixing on the spatio-temporal progression of two-stage autoignition of diesel-sprays in low-reactivity ambient fuel-air mixture
The spatial and temporal locations of autoignition for direct-injection compression-ignition engines depend on fuel chemistry, temperature, pressure, and mixing trajectories in the fuel jets. Dual-fuel systems can provide insight into both fuel-chemistry and physical effects by varying fuel reactivities and engine operating conditions. In this context, the spatial and temporal progression of two-stage autoignition of a diesel-fuel surrogate, n-heptane, in a lean-premixed charge of synthetic natural-gas (NG) and air is imaged in an optically accessible heavy-duty diesel engine. The lean-premixed charge of NG is prepared by fumigation upstream of the engine intake manifold. Optical diagnostics include high-speed (15kfps) cool-flame chemiluminescence-imaging as an indicator of low-temperature heat-release (LTHR) and OH* chemiluminescence-imaging as an indicator high-temperature heat-release (HTHR). NG prolongs the ignition delay of the pilot fuel and increases the combustion duration. Zero-dimensional chemical-kinetics simulations provide further understanding by replicating a Lagrangian perspective for mixtures evolving along streamlines originating either at the fuel nozzle or in the ambient gas, for which the pilot-fuel concentration is either decreasing or increasing, respectively. The zero-dimensional simulations predict that LTHR initiates most likely on the air streamlines before transitioning to HTHR, either on fuel-streamlines or on air-streamlines in regions of near-constant φ. Due to the relatively short pilot-fuel injection-durations, the transient increase in entrainment near the end of injection (entrainment wave) is important for quickly creating auto-ignitable mixtures. To achieve desired combustion characteristics, e.g., multiple ignition-kernels and favorable combustion phasing and location (e.g., for reducing wall heat-transfer or optimizing charge stratification), adjusting injection parameters could tailor mixing trajectories to offset changes in fuel ignition chemistry.
Exploring the Effects of Piston Bowl Geometry and Injector Included Angle on Dual-Fuel and Single-Fuel RCCI
Abstract Reactivity control compression ignition (RCCI) is a low-temperature combustion technique that has been proposed to meet the current demand for high thermal efficiency and low engine-out emissions. However, its requirement of two separate fuel systems (i.e., a low-reactivity fuel system and a high-reactivity fuel system) has been one of its major challenges in the last decade. This leads to the single-fuel RCCI concept, where the secondary fuel (reformates of diesel) is generated from the primary fuel (diesel) through catalytic partial oxidation reformation. Following the in-depth analysis of the reformate fuel (reformates of diesel) and its benefit as the low-reactivity fuel with diesel, the effects of the start of injection (SOI) timing of diesel and the energy-based blend ratio were also studied in detail. In this study, the effects of piston profile and the injector included angles were experimentally examined using both conventional fuel pairs (gasoline—diesel and natural gas—diesel) and reformate RCCI. A validated computational fluid dynamics (CFD) model was also used for a better understanding of the experimental trends. Comparing a reentrant bowl piston with a shallow bowl piston at a constant compression ratio and SOI, the latter showed better thermal efficiency, regardless of the fuel combination, due to its 10% lower surface area for the heat transfer. Comparing the 150-degree included angle and 60-degree included angle on the shallow bowl piston, the latter showed better combustion efficiency, regardless of the fuel combination, due to its earlier combustion phasing (at constant SOI timing). The effect was particularly prominent on reformate RCCI because of its incredibly high diluent concentration, which retards the combustion further for the 150-deg injector. Later, using convergecfd, seven different injector included angles were studied at a constant SOI. With the change in injector included angle, the region of the cylinder targeted by the fuel spray varies significantly, and it was found to have a significant impact on the combustion efficiency and the engine-out emissions. As the injector included angle changed from 60-deg to 150-deg, the combustion efficiency increased by 15% and the CO, NOx, and HC emissions decreased by 96%, 70%, and 86%, respectively.
Fuel-rich catalytic combustion of a high density fuel
Fuel-rich catalytic combustion (ER is greater than 4) of the high density fuel exo-tetrahydrocyclopentadiene (JP-10) was studied over the equivalence ratio range 5.0 to 7.6, which yielded combustion temperatures of 1220 to 1120 K. The process produced soot-free gaseous products similar to those obtained with iso-octane and jet-A in previous studies. The measured combustion temperature agreed well with that calculated assuming soot was not a combustion product. The process raised the effective hydrogen/carbon (H/C) ratio from 1.6 to over 2.0, thus significantly improving the combustion properties of the fuel. At an equivalence ratio near 5.0, about 80 percent of the initial fuel carbon was in light gaseous products and about 20 percent in larger condensable molecules. Fuel-rich catalytic combustion has now been studied for three fuels with H/C ratios of 2.25 (iso-octane), 1.92 (jet-A), and 1.6 (JP-10). A comparison of the product distribution of these fuels shows that, in general, the measured concentrations of the combustion products were monotonic functions of the H/C ratio with the exception of hydrogen and ethylene. In these cases, data for JP-10 fell between iso-octane and jet-A rather than beyond jet-A. It is suggested that the ring cross-linking structure of JP-10 may be responsible for this behavior. All the fuels studied showed that the largest amounts of small hydrocarbon molecules and the smallest amounts of large condensable molecules occurred at the lower equivalence ratios. This corresponds to the highest combustion temperatures used in these studies. Although higher temperatures may improve this mix, the temperature is limited. First, the life of the present catalyst would be greatly shortened when operated at temperatures of 1300 K or greater. Second, fuel-rich catalytic combustion does not produce soot because the combustion temperatures used in the experiments were well below the threshold temperature (1350 K) for the formation of soot. Increasing the temperature above this value would remove the soot-free nature of the process. Since all the fuels studied show a similar breakdown of the primary fuel into smaller molecular combustion products, this technique can be applied to all hydrocarbon fuels.
Fuel injector including a lobed mixer and vanes for injecting alternate fuels in a gas turbine
A fuel injector for injecting alternate fuels having a different energy density in a gas turbine is provided. A first fuel supply channel (18) may be fluidly coupled to a radial passage (22) in a plurality of vanes (20) that branches into passages (24) (e.g., axial passages) to inject a first fuel without jet in cross-flow injection. This may be effective to reduce flashback in fuels having a relatively high flame speed. A mixer (30) with lobes (32) for injection of a second fuel may be arranged at the downstream end of a fuel delivery tube (12). A fuel-routing structure (38) may be configured to route the second fuel within a respective lobe so that fuel injection of the second fuel takes place radially outwardly relative to a central region of the mixer. This may be conducive to an improved (e.g., a relatively more uniform) mixing of air and fuel.
A jet fuel surrogate formulated by real fuel properties
An implicit methodology based on chemical group theory to formulate a jet aviation fuel surrogate by the measurements of several combustion related fuel properties is tested. The empirical formula and derived cetane number of an actual aviation fuel, POSF 4658, have been determined. A three component surrogate fuel for POSF 4658 has been formulated by constraining a mixture of n-decane, iso-octane and toluene to reproduce the hydrogen/carbon ratio and derived cetane number of the target fuel. The validity of the proposed surrogate is evaluated by experimental measurement of select combustion properties of POSF 4658, and the POSF 4658 surrogate. (1)A variable pressure flow reactor has been used to chart the chemical reactivity of stoichiometric mixtures of POSF 4658/O{sub 2}/N{sub 2} and POSF 4658 surrogate/O{sub 2}/N{sub 2} at 12.5 atm and 500-1000 K, fixing the carbon content at 0.3% for both mixtures. (2)The high temperature chemical reactivity and chemical kinetic-molecular diffusion coupling of POSF 4658 and POSF 4658 surrogate have been evaluated by measurement of the strained extinction limit of diffusion flames. (3)The autoignition behavior of POSF 4658 and POSF 4658 surrogate has been measured with a shock tube at 674-1222 K and with a rapid compression machine at 645-714 K for stoichiometric mixtures of fuel in air at pressures close to 20 atm. The flow reactor study shows that the character and extent of chemical reactivity of both fuels at low temperature (500-675 K) and high temperature (900 K+) are extremely similar. Slight differences in the transition from the end of the negative temperature coefficient regime to hot ignition are observed. The diffusion flame strained extinction limits of the fuels are observed to be indistinguishable when compared on a molar basis. Ignition delay measurements also show that POSF 4658 exhibits NTC behavior. Moreover, the ignition delays of both fuels are also extremely similar over the temperature range studied in both shock tube and rapid compression machine experiments. A chemical kinetic model is constructed and utilized to interpret the experimental observations and provides a rationale as to why the real fuel and surrogate fuel exhibit such similar reactivity. (author)
Simulations of Failure via Three-Dimensional Cracking in Fuel Cladding for Advanced Nuclear Fuels
Enhancing performance of fuel cladding and duct alloys is a key means of increasing fuel burnup. This project will address the failure of fuel cladding via three-dimensional cracking models. Researchers will develop a simulation code for the failure of the fuel cladding and validate the code through experiments. The objective is to develop an algorithm to determine the failure of fuel cladding in the form of three-dimensional cracking due to prolonged exposure under varying conditions of pressure, temperature, chemical environment, and irradiation. This project encompasses the following tasks: 1. Simulate 3D crack initiation and growth under instantaneous and/or fatigue loads using a new variant of the material point method (MPM); 2. Simulate debonding of the materials in the crack path using cohesive elements, considering normal and shear traction separation laws; 3. Determine the crack propagation path, considering damage of the materials incorporated in the cohesive elements to allow the energy release rate to be minimized; 4. Simulate the three-dimensional fatigue crack growth as a function of loading histories; 5. Verify the simulation code by comparing results to theoretical and numerical studies available in the literature; 6. Conduct experiments to observe the crack path and surface profile in unused fuel cladding and validate against simulation results; and 7. Expand the adaptive mesh refinement infrastructure parallel processing environment to allow adaptive mesh refinement at the 3D crack fronts and adaptive mesh merging in the wake of cracks. Fuel cladding is made of materials such as stainless steels and ferritic steels with added alloying elements, which increase stability and durability under irradiation. As fuel cladding is subjected to water, chemicals, fission gas, pressure, high temperatures, and irradiation while in service, understanding performance is essential. In the fast fuel used in advanced burner reactors, simulations of the nuclear fuels are critical to understand the burnup, and thus the fuel efficiency.
Isotopic and Fuel Lattice Parameter Trends in Extended Enrichment and Higher Burnup LWR Fuel, Volume II: BWR
Commercial light water reactor (LWR) operators and fuel vendors in the United States are pursuing changes to nuclear fuel that include extended enrichment (EE) and accident-tolerant fuel (ATF) designs to further improve reactor safety and plant economics. Extended fuel enrichments above 5% 235 U pin enrichment and up to 10% 235 U are a subset of high assay low-enriched uranium (HALEU) that may be deployed in commercial US LWRs in the near term. ATF features, such as cladding coatings or alternative cladding materials, are designed to improve fuel system performance under accident conditions. One goal of EE is to improve fuel cycle economy by enabling fuel to be depleted to higher burnup than the typical current limits (62 gigawatt-days per metric ton of uranium [GWd/MTU]). Adoption of EE, ATF, and high burnup (HBU) fuels in the US commercial fleet requires a clear understanding of the effects on core physics parameters and used fuel isotopic content, as well as confidence in the accuracy of computer code predictions over an expanded range of materials, enrichment, and burnup. A thorough understanding of the applicability and adequacy of benchmark data (e.g., criticality, decay heat, isotopic content) for computer code validation is necessary to ensure that appropriate safety margins are maintained. As part of the US Nuclear Regulatory Commission (NRC) agreement number 31310019N0008, “SCALE Code Development, Assessment and Maintenance,” the effects of EE, ATF, and HBU are being assessed for selected representative LWR fuel designs. The project is divided into phases, and this report summarizes the findings of the Phase 1 work, which focuses on lattice physics parameter and used fuel isotopic changes for a conventional GE14 10 x 10 boiling water reactor (BWR) design with GNF-2 part length rod patterns to model a modern BWR assembly design.