Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Destructive Examination of a FeCrAl-UO 2 Irradiation Test

Several destructive postirradiation examinations were performed on an irradiation specimen that coupled an early iron-chromium-aluminum (FeCrAl) candidate alloy cladding with UO2 pellets. This irradiation test was designed to investigate the early life performance and compatibility of the FeCrAl-UO 2 cladding-fuel system under prototypic light water reactor neutronic conditions. Additionally, these tests were expected to provide neutron irradiated samples for severe accident testing of this fuel system. The irradiation studied in this work was part of the ATF-1 series of drop-in style irradiations performed in the Idaho National Laboratory Advanced Test Reactor. The rodlet studied in this work is one of three similar rodlets irradiated in ATF-1 that had approximately 7.6 cm of cladding machined from a wrought FeCrAl alloy and fueled with a 6.1 cm stack of UO 2 pellets. The outer diameter of the cladding was ~0.94 cm and the inner diameter was ~0.83 cm. After irradiation and non-destructive examination in Idaho this rodlet was shipped to the Oak Ridge National Laboratory hot-cells for further examination. The irradiated rodlet was sectioned into several samples for microstructural, micromechanical, and severe accident testing. During sectioning, it was noted that the fuel was not firmly bonded to the cladding and could be readily removed from small cladding slices. Microstructural characterization of fuel cross sections also revealed no significant interaction between the fuel and the cladding. Samples were also prepared for microhardness testing. To prepare for high temperature oxidation testing, the fuel was dissolved from segments of the cladding. High temperature oxidation testing of cladding segments was performed at 1200°C and 1300°C in a steam environment. Comparisons between the oxidation of this FeCrAl alloy in its neutron irradiated state, as-fabricated state, and the oxidation of Zircaloy-2 are made. The oxidation testing will be followed by ring compression testing to evaluate ductility. The microstructure of the samples after oxidation and ring compression testing will also be analyzed.

Harp, Jason↗
DOE OSTI2024

Evaluation of Sb-Nd and Te-Nd phases within the U-Zr fuel matrix and their interactions with HT9 alloy

Antimony (Sb) and tellurium (Te) were investigated as potential additives for U-10Zr (wt.%) metallic fuel to limit the fuel-cladding chemical interaction (FCCI) with HT-9 alloy. Neodymium (Nd) was utilized to simulate the formation of lanthanide-based solid fission products which are known to play a detrimental role in FCCI. Fuel alloys of U-Zr-Sb-Nd and U-Zr-Te-Nd were evaluated in their annealed condition and compared against their as-cast conditions. Isothermal diffusion couple experiments were performed between U-Zr-Nd, U-Zr-Sb-Nd, and U-Zr-Te-Nd against the cladding alloy HT9 to evaluate the effectiveness of the additives to stabilize Nd within the fuel alloys, as well as investigate the interaction regions that form between the different fuel alloys and HT9. Further, SbNd and Sb 3 Nd 4 , and TeNd are found to be the primary neodymium-based phases formed in the U-Zr-Sb-Nd and U-Zr-Te-Nd alloys, respectively. The zirconium-based phase, Zr 2 Sb, is also found to form within the former alloy. All phases were found to remain stable through the diffusion experiments and exhibited no interaction with HT9 constituent elements. Preferential interaction between Nd with additivities Te and Sb compared to constituting elements in HT9 was further verified based on density functional theory (DFT) calculated enthalpy of mixing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

FPMS_XPeRT_INL_Poster

As nuclear energy expands and experimental programs increasingly rely on the facilities at Idaho National Laboratory (INL) for reactor and fuel testing, research capabilities must also expand to meet these demands. A new Fission Product Monitoring System (FPMS) has been deployed at the Advanced Test Reactor (ATR) at the Auxiliary Lead-out Experiment (ALE) House to support this expanding fuel testing mission. By tracking gaseous fission products releases from test fuel in near real-time, release rates, calculated from FPMS data, can be used to characterize the effectiveness of fuel cladding, especially for Tri-structural Isotropic (TRISO) fuel concepts. The new iteration of the FPMS supports up to 14 fission product monitors for online fission-product tracking via gamma-ray spectroscopy of the experiment’s effluent gas. Each monitor consists of a nominally 10% HPGe detector housed in a copper-lined lead shield with a warm gas trap. The new system features gamma-ray count rate information with a five-second temporal resolution and provides isotopic activity every five minutes, capable of resolving multiple overlapping fission product releases over a broad range of activities in near real-time. This work includes data from ATR cycle 175D data to demonstrate these capabilities. The hourly resolution data shows general trends and significant releases over the cycle, while the 5-minute resolution data allows for a more detailed examination of events due to unexpected particle releases.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
DOE OSTI2020

Investigating Uranium Corrosion in Magnesium-containing Sludge Using X-ray Tomography - 20042

One of the current primary concerns within the British nuclear community is the decommissioning of legacy storage ponds in Sellafield Cumbria, where nuclear fuel cladding material (a Mg-Al alloy) resides along with fuel metallic swarf. Corrosion of the immersed metallic elements, which has been occurring over the storage period, has resulted in the formation of what is commonly known as Corroded Magnox Sludge. The behaviour of uranium metal within this particular environment and, more significantly, the identity of the corrosion products that may have formed is currently unknown. The present study attempts to shed some light on these aspects by investigating simplified surrogate systems, mimicking storage ponds. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

First Examination of Irradiated Fuel with Pulsed Neutrons at LANSCE (Preliminary Results)

We present preliminary results on the characterization of an irradiated U-lOZr-lPd fuel sample that was prepared from the irradiated AFC-3A-R5A sample. U-lOZr metallic fuels are researched as host materials for potential transmutation fuels and the addition of palladium strives to bind lanthanides, thus preventing fuel-cladding chemical interactions (FCCI). These interactions limit the lifetime of metallic fuels and are caused by migration of lanthanide fission products to the periphery of the fuel slug, where they start to interact with the D9 or HT9 steel cladding, ultimately leading to failure of the mechanical integrity of the cladding. Neutrons offer bulk characterization of irradiated materials for which X-ray tomography methods are not suitable due to the immense gamma background emitted from the samples. In particular pulsed neutrons provide information from the ability to resolve the neutron energy using their time-of-flight and thus the potential to utilize neutron absorption resonance to characterize the spatial distribution of isotopes. This, in turn, may allow to characterize the distribution of fission and neutron capture products non-destructively and may ultimately be applied to the bulk of an irradiation capsule prior to destructive post-irradiation examination to identify regions of interest. To allow the characterization of entire irradiation capsules, a cask is under development in the advanced post-irradiation work package at LANL and progress on this development was reported elsewhere. In parallel, an irradiated U-lOZr-lPd sample cut from the AFC-3AR5A irradiation was shipped to LANL and will be fully characterized with an NSUF funded rapid turnaround experiment (RTE) in the 2020 LANSCE run cycle. The sample emits at a dose rate of ~3R/hr on contact and is therefore manageable with remote handling, without requiring a cask. The disk-shaped material is larger than samples prepared for analysis using electron or X-ray methods and is therefore an intermediate step towards characterization of bulk samples at LANSCE. However, since it covers the full diameter of the irradiated fuel slug, some insight on redistribution of elements, spatially resolved information on microstructure, e.g. phase composition and texture, will be possible using the pulsed neutron-based methods developed for fuel characterization at LANSCE. This report describes the development of procedures to handle the sample at LANSCE as well as preliminary data and results from tests conducted in December 2019 on the energy-resolved neutron imaging (ERNI) beam line at flight path 5 and the high pressure-preferred orientation diffractometer (HIPPO) at LANSCE. This effort is a collaboration between LANL, INL, and ORNL. To compare our capabilities with prior work, we present an overview of previously reported bulk characterization of irradiated or spent fuels. The overview addresses neutron diffraction and neutron absorption resonance spectroscopy, both of which have only few reported applications on irradiated or spent nuclear fuel, as well as neutron radiography. This literature review was already described in a previous report but is repeated here to put our current efforts in context of previous work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Unraveling the Mechanics: Computational Modeling of Residual Stresses in U10Mo Fuel with Aluminum Cladding

LEU (Low Enriched Uranium) plate-type fuel elements consist of a high-density, low-enrichment U–Mo alloy-based fuel foil encapsulated in an aluminum cladding and is fabricated through the Hot Isostatic Pressing (HIP) technique. Understanding the mechanism of possible failure modes of nuclear fuel is critical to mitigate potential consequences. One of the major contributing factors in various failure modes is stress and it greatly affects the integrity under temperature, pressure, and irradiation. These stresses could originate from various sources, including manufacturing, and operation, and can lead to deformation, cracking, or even complete failure of fuel elements. This study focuses on the development of a computational model that accurately predicts the residual stresses generated in the U10Mo fuel during fabrication. It has been observed that cladding creep has a substantial impact on the residual stresses in the U10Mo fuel post the HIP fabrication process. Furthermore, during the HIP bonding process the fuel plate system is heated to a temperature of 560 oC and as a result, the aluminum cladding transitions from (Al 6061-T6 to -O). This presents a challenge in capturing the change in material properties accurately. Therefore, a temperature dependent creep model such as hyperbolic sine creep model is considered to estimate the creep properties of the Aluminum cladding. The proposed calibrated creep model accurately predicts the residual stresses in the U10Mo fuel foil and agrees well with the experiments.

42 ENGINEERING↗
DOE OSTI2022

In-situ thermomechanical measurements during burst testing of Zr claddings using digital image correlation and infrared thermography techniques

Burst testing has long been a relied-on method for assessing fuel cladding materials in light-water reactoraccident scenarios. However, burst testing historically provided minimal in-situ observations beyond a few thermocouple readings, pressure from transducers, and post-test deformation measurements. Acquisition of full cladding thermomechanical data throughout a burst test would be invaluable to fuel system qualification, material model development and fuel performance code validation, such as the BISON fuel performance code. Recently, methodologies for simultaneously applying 2-dimensional digital image correlation and infrared thermography techniques to quantify the relationship between temperature, internal cladding pressure, and deformation during burst testing were developed. This work details results from the application of these techniques to burst testing of Zircaloy-4 cladding segments subjected to loss-of-coolant accident transients in an air environment. Two types of tests were performed with: (a) cladding segments connected to a fixed pressure reservoir as well as (b) closed systems where internal pressure increased during transients. In-situ thermomechanical measurements including strain and thermal gradient data are presented, demonstrating the effectiveness of applying combined surface measurement techniques to burst testing

Bell, Sam↗
DOE OSTI2020

Amphiphilic Block Copolymers for Flocculation and Hydrophobization of Legacy Waste Suspensions in Flotation Driven Dewatering Operations - 20162

Flotation has been effectively demonstrated as a low footprint, high efficiency separation process when utilising simple anionic surface modifying agents such as sodium dodecyl sulphate (SDS). These agents increase hydrophobicity to remove suspended cationic surface charged particulates such as Mg(OH){sub 2} from waste suspensions similar to those at British nuclear fuel management sites- where corrosion processes have degraded fuel cladding. The technology is advantageous as it could effectively be retrofitted into existing waste management facilities at nuclear waste management sites such Sellafield and Hanford as the simplicity (no moving parts) and size of this technology coupled with low cost of construction could be rapidly deployed to aid in risk and hazard reduction decommissioning operations with minimum impact to secondary waste generation. Previously, sodium dodecyl sulphate has been deployed as a collector agent to increase the hydrophobicity of Mg(OH){sub 2} suspended particles, achieving a maximum particulate extraction percentage of 93%. To achieve further particulate extraction, flotation performance has been determined to be a function of the hydrodynamic limitations extracting fine material (>20 μm). Fine particulates have been shown in the minerals industry to have an inability to overcome slipstreams created from rising bubbles in flotation cells, likely due to the low mass and thus momentum of the colloidal material, preventing interaction between the hydrophobized particles and air-water interfaces (bubbles). To combat this mass transfer resistance poly(acrylic acid)-block-poly(n-butyl acrylate) amphiphilic diblock copolymers were synthesised via reversible addition-fragmentation chain-transfer (RAFT) polymerisation. The anticipated mode of action of these polymers involves the hydrophilic poly(acrylic acid) block polymer acting as a flocculation agent to increase the mass of the aggregates, and the hydrophobic poly(n-butyl acrylate) modifies the hydrophobicity of the resulting flocs. The concentration of this polymer (termed a macro-collector) was varied and the change in particle size distribution of the particulate suspension was analysed using static light scattering. The flotation performance was then characterised by several methods including percentage particulate recovery, volume reduction factor and residual bulk particulate concentration. This was then benchmarked against the traditional surfactant collector agent SDS. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Review and Summary of Corrosion Behavior for Aluminum-Clad Spent Nuclear Fuel in Dry Storage

A description of the corrosion behavior of aluminum alloys used for cladding on aluminum-based, aluminum-clad nuclear fuel used in research reactors under potential dry storage conditions has been compiled. An evaluation is made of potential additional corrosion with water postulated to not be removed during drying. The relative humidity (RH) produced by typical dryness criteria for industrial spent nuclear fuel drying is expected to be low, particularly at high temperatures (17% RH at 20°C and lower at higher temperatures). Existing corrosion data suggests that negligible vapor-phase corrosion of aluminum is expected at such low humidity, even for nominally bare aluminum surfaces. That is, the predicted relative humidity from free water (e.g., 17% RH) is below the “critical” relative humidity (~40% RH at room temperature), below which no significant corrosion is observed for bare aluminum. Furthermore, reported room-temperature corrosion rates are very low even under saturated (100% RH) water vapor. Existing results showing significant vapor-phase corrosion corresponded specifically to conditions of high temper ed with high relative humidity. A relatively large reservoir of (chemically bound) water exists in the aluminum (oxy)hydroxide films on the SNF cladding surface. The estimated total could saturate the gas even at relatively high temperature if fully released; however, its release as molecular water is expected to only be plausible if the temperature during storage exceeds both the drying temperature and the threshold for thermal decomposition of the trihydroxides (~220°C). Therefore, the combination of high temperature and high relative humidity that could drive significant corrosion is considered implausible during sealed dry storage following an appropriate drying process, to include >220°C drying for canisters that may approach or exceed this temperature during storage. Vapor-phase testing of aluminum samples with an adherent (oxy)hydroxide layer, prepared in liquid water to resemble those on actual aluminum-clad spent nuclear fuel (ASNF), did not observe evidence of additional corrosion even at combined high-temperature (up to 180°C) and high-humidity (up to 100% RH) conditions. Instead, small net mass losses were observed for most specimens and attributed to dehydration of the samples, which had been air-dried only prior to testing. ASNF being moved to dry storage is expected to have an existing (oxy)hydroxide film, suggesting that the cladding will be less prone to additional corrosion than bare aluminum metal. If significant corrosion did occur during sealed storage, the overall extent and impact is expected to be small. Corrosion post-closure of a canister would not alter the total amount of hydrogen in the canister, so it would have no effect on the maximum H 2 release already assessed in existing bounding calculations. In addition, the total amount of water in a 25-µm dense bayerite film would consume a only ~8 µm additional aluminum metal on average, if fully consumed by oxidizing aluminum metal to Al 2 O 3 . These conclusions are consistent with ASNF-in-canister simulations to date, which included a reaction pathway for corrosion using kinetics from previous literature and believed to be conservative and predicted very low rates of corrosion.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Effects of 18 O Exchange on Neutron Emission Rates of Aging 238 PuO 2 LWRHUs

The Lightweight Radioisotope Heater Unit (LWRHU) provides about 1 Watt of thermal power to critical electrical and mechanical systems in the extreme temperatures of space, maintaining the operating temperature of the spacecraft’s scientific and general operating equipment. Los Alamos National Laboratory (LANL) designed and tested the LWRHU in the 1970s through early 1980s. The first production campaign at LANL was in the early 1980s in support of the Galileo mission in which over 100 LWRHUs were manufactured. In the mid-1990s, almost 200 LWRHUs were manufactured in support of the Cassini mission. After the primary Cassini manufacturing campaign, the Department of Energy (DOE) approved the fabrication of more than 10 additional LWRHUs as spares in 1998. The LWRHU assembly contains the following components: a fuel pellet, a vented capsule, a pyrolytic graphite insulator, and a fine-weave pierced fabric (FWPF) graphite aeroshell. The fuel pellet is a hot-pressed 238 PuO 2 cylindrical pellet that is sintered to create a ceramic pellet. The pellet is encapsulated in a platinum-rhodium encapsulation. The welded fueled clad is placed inside a pyrolytic graphite thermal insulation to protect the fuel from the heat produced in reentry events. The exterior layer of the LWRHU assembly is the FWPF aeroshell. Before sintering, PuO 2 granules are heated in a furnace at temperatures greater than or equal to 700°C under an enriched 16 O atmosphere in order to reduce trace quantities of 18 O. Because 18 O undergoes an (α,n) reaction, 18 O needs to be removed as much as possible to meet radiation emission requirements set by the Jet Propulsion Laboratory (JPL) and the National Aeronautics and Space Administration (NASA), as well as other agencies. The relative abundances of the oxygen isotopes are indicated by neutron emission rate (NER) measurements. LWRHUs are vented with a sintered platinum frit vent (George 1986). During extraterrestrial operation, the vent in the cladding allows helium from the decay of plutonium to escape and relieves pressure from the system while preventing the solids from escaping (Rinehart 1996, Tate 1982 & 1985). This vent is protected during manufacture by a platinum-30 rhodium cover. The capsule vent is activated by milling a 0.025-inch diameter hole through the protective cover to a nominal depth of 0.015 inches, generally immediately before the LWRHU is loaded into the aeroshell (George 1986). Prior to long-term storage, LWRHUs are vented and thus potentially allow infiltration of 18 O from the ambient atmosphere. Although NER decreases with age due to the reduction in emitted alpha particles, it might be expected that NER reduction is mitigated by the exchange of 18 O. However, this is not necessarily the case and no trend was observed relating NER to age other than the natural decay of 238 Pu (Mulford 2021). The most probable and dominant factor for determining specific NER was manufacturing discrepancies between individual units. It is important to understand the lack of observed 16 O- 18 O exchange and to compare LWRHU pellets as much as possible.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Microstructural and chemical characterization of medium burnup fast reactor MOX using electron microscopy

A thorough post-irradiation examination campaign of medium burnup Sodium Fast Reactor (SFR) mixed oxide (MOX) fuel has been undertaken over the past two years to better understand the performance at intermediate burnup of this annular fuel design. Non-destructive examinations as well as destructive examinations of two pins have been recently published by the authors, providing data regarding the performance at macro-scale. The analyses of selected samples have continued to provide more details regarding the overall microstructure and, particularly, the fuel-cladding interaction.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Research Needs for Uranium-Zirconium- Based Metallic Fuels

The purpose of this report is to summarize the needs and present recommendations related to the future direction for U-Zr-based metallic fuel research (including binary U-Zr and ternary U-Pu-Zr alloys). These needs and recommendations were determined by subject matter experts from various institutions during a two-day workshop held at the University of Florida in November, 2019. During open-floor discussions, the highest priority gaps in our understanding of U-Zr-based fuels were down-selected, and near- and long-term needs that directly impact the implementation of these metallic fuels were identified. The identified near-term needs include investigation of the following phenomena: i) swelling and fission gas release, ii) fuel-cladding chemical interaction, iii) phase evolution/constituent redistribution, and iv) thermal properties of the fuels. The long-term needs are: i) investigation of fuel creep and plasticity and ii) fission product (lanthanide) transport. In addition, there was general agreement that all institutions and subject matter experts would benefit from an open-source metallic fuels database with thermophysical property and microstructural data, along with fuel operation/irradiation history, which should be regularly updated with vetted information from new experimental and computational investigations and used to advance metallic fuels research and development. Finally, we recommend that metallic fuel research should be ongoing and that fuel qualification and fuel optimization should be equally prioritized; research combining experiments with modeling and simulation has the largest potential impact.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Results of Oklo Diffusion Couple Experiments

Through the Gateway for Accelerated Innovation in Nuclear (GAIN) initiative, the U.S. Department of Energy funded a GAIN Nuclear Energy Voucher to perform out-of-pile experiments related to the fuel design for Oklo Inc., headquartered in Santa Clara, CA. GAIN’s goal is to accelerate the innovation and application of advanced nuclear technologies, and voucher recipients do not receive direct financial awards but are provided access to national laboratory capabilities at no cost. This report documents the results of diffusion couple experiments performed as part of the GAIN-funded project for Oklo. This work addresses the specific problem of filling the gap in understanding of the fuel-cladding chemical interaction (FCCI) that result from the past focus on a particular fuel design. These knowledge and mechanistic modeling gaps make it difficult to extrapolate from prior fuel performance data to advance an economically competitive fuel design. Specifically, the current state-of-the-art fuel performance modeling cannot separate the entangled effects of temperature ranges, burnups, materials, and geometries.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Considerations for Defining G-Values for Aluminum-Clad Spent Nuclear Fuel

Sealed-canister dry storage of aluminum-clad spent nuclear fuel (ASNF) generated by research reactors is an alternative to current storage and disposition pathways as directed by the U.S. Department of Energy. The major challenge faced for this storage approach is radiolytic H 2 generation, including from the aluminum (oxy)hydroxide layers on the surface of ASNF. Experimental and modeling activities have been carried out to characterize the radiolytic yield as part of a DOE-sponsored research program to develop the technical basis for ASNF dry storage. The G-value is a commonly way to report results of radiolysis testing and is defined as the radiolytic yield of a species (e.g. molecular hydrogen) per unit radiation energy deposited into the material system. An independent technical review of the ASNF dry storage technical basis performed by Pacific Northwest National Laboratory raised questions about differences in G-value definitions used for experiments on ASNF surrogates consisting of aluminum samples with adherent (oxy)hydroxides compared to G-values reported in prior literature and how the magnitudes compared between different studies. Material systems resembling ASNF pose complications for measuring/defining G-values to predict the evolution of H 2 in a sealed canister, including i) accounting for radiolytic yields potentially arising from multiple sources, i.e., residual free (vapor), physisorbed, and chemisorbed/chemically bound waters; ii) deciding what portions of the multi-material system to include in the absorbed energy (radiation dose) calculation, considering possible energy exchange between materials as well as measurement limitations, and iii) capturing variations in G-value associated with non-linear yield vs. dose curves and/or dependence on the cover gas. This report summarizes previous literature information on radiolytic H 2 generation and associated G-values from mixed-material systems (generally oxides in contact with water or organic compounds) and from (oxy)hydroxides/hydrates to compare with the definitions and values for ASNF surrogate samples containing adherent aluminum (oxy)hydroxides.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Mechanistic modeling of lifetime distribution of SiC/SiC composite claddings

Silicon carbide (SiC) fiber-reinforced SiC matrix (SiC/SiC) composites have emerged as a new material candidate for fuel claddings in light water reactors. Recent studies showed that the load capacity of SiC/SiC materials exhibits a considerable statistical variation. Therefore, reliability analysis plays a critical role in design of SiC/SiC composite claddings. Here, this paper presents a probabilistic model for the lifetime distribution of SiC/SiC composites. The model is anchored by a multiaxial stress-based failure criterion and subcritical damage accumulation mechanism. Based on the kinetics of subcritical damage growth, the lifetime distribution of a laboratory test specimen for any given loading history can be calculated. A finite weakest-link model is used to extrapolate the lifetime distribution of test specimens to full-length claddings. It is shown that the damage accumulation mechanism has a strong influence on the lifetime distribution of the cladding. This finding highlights the importance of understanding the static fatigue behavior of SiC/SiC composites. The present analysis also demonstrates an intricate length effect on the failure probability of the cladding, which is expected to play a crucial role in design extrapolation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dissolution Flowsheet for Skull Oxide Generated during U-Mo Alloy Casting for High Performance Research Reactor Fuel

The Savannah River National Laboratory was requested to develop dissolution flowsheets for high assay low enriched U scrap generated during the fabrication of high performance research reactor fuel. The scrap streams include U-10Mo and U-10Mo-Zr foils, rejected Al-clad fuel plates, and skull oxide from casting molds. Flowsheets for the dissolution of the U-10Mo-Zr foils and Al-clad U-10Mo-Zr mini-plates received from BWX Technologies, Inc were developed and demonstrated in the first phase of this project. In the second phase (this work), the skull oxide from a U-10Mo casting mold was obtained from the Y-12 National Security Complex (Y-12) and small-scale experiments were performed to demonstrate dissolution flowsheets.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

FY2022 Progress Report for Advanced Re-fabrication/Re-instrumentation Capability Development

In support of performing follow-on irradiation experiments with previously irradiated materials, the Halden Reactor Project developed unique and state of the art capabilities to refabricate and re-instrument previously irradiated materials. Such materials were used in in-pile tests at the Halden reactor, and out-of-pile tests for example using furnaces as a heat source. The decision to close the Halden Reactor Project results in the loss of this refabrication and re-instrumentation capability. As a result, the United States (U.S.) Department of Energy (DOE) has determined to develop refabrication and re-instrumentation capability at the unique shielded facilities at Idaho National Laboratory (INL). The development of refabrication capability has been completed and demonstrated. This report focuses on the complementary aspects of reinstrumentation and the progress to-date. Halden spent nearly 30 years developing both refabrication and re-instrumentation. Collaboration with Halden is allowing Idaho National Laboratory (INL) to develop this capability much more rapidly. In FY-21 the results include development of the capability to drill annular center holes in ceramic UO2 fuel pellets, development of fuel rod end caps with feedthroughs for centerline instrumentation inside the rodlet, The procurement of both fuel drilling and welding demonstration equipment from Halden, evaluation of surface thermocouple attachments to support better understanding of temperature measurement uncertainties, and finally, the conceptual design of a new shielded enclosure where advanced refabrication and re-instrumentation equipment can be housed. In FY-22, the results include; Completing set up of the drilling and welding modules procured from Halden, and early experimental trials using that equipment.; Completing set up of an out-of-cell circumferential weld system to allow for further weld development to take place and support fabrication of fuel for fresh fuel experiments.; Evaluation of the Hot Fuel Examination Facility (HFEF) infrastructure to support future installation of advanced re-fabrication/re-instrumentation equipment, specifically related to necessary infrastructure for cryo-drilling.; Developments in dry-drilling alternative. Including experimental studies showing cordierite is the most suitable surrogate for UO 2 for performing drilling studies. That drilling performance is enhanced when a fuel-clad bonding condition is simulated.; Conceptual design completed for attaching surface thermocouples to irradiated fuel in support of TWIST capsule experiments. The authors would like to thank the numerous colleagues at INL and Halden who provided support in accomplishing this work. Their support both material and intellectual is invaluable in advancing the state of the art and establishing the capabilities for refabrication and re-instrumentation at INL.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗