Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Rod Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

ORNL Interim Progress Report on Hydride Reorientation CIRFT Tests

A systematic study of H. B. Robinson (HBR) high burnup spent nuclear fuel (SNF) vibration integrity was performed in Phase I project under simulated transportation environments, using the Cyclic Integrated Reversible-Bending Fatigue Tester (CIRFT) hot cell testing technology developed at Oak Ridge National Laboratory in 2013–14. The data analysis on the as-irradiated HBR SNF rods demonstrated that the load amplitude is the dominant factor that controls the fatigue life of bending rods. However, previous studies have shown that the hydrogen content and hydride morphology has an important effect on zirconium alloy mechanical properties. To address the effect of radial hydrides in SNF rods, in Phase II a test procedure was developed to simulate the effects of elevated temperatures, pressures, and stresses during transfer-drying operations. Pressurized and sealed fuel segments were heated to the target temperature for a preset hold time and slow-cooled at a controlled rate. The procedure was applied to both non-irradiated/prehydrided and high-burnup Zircaloy-4 fueled cladding segments using the Nuclear Regulatory Commission-recommended 400°C maximum temperature limit at various cooling rates. Before testing high-burnup cladding, four out-of-cell tests were conducted to optimize the hydride reorientation (R) test condition with pre-hydride Zircaloy-4 cladding, which has the same geometry as the high burnup fuel samples. Test HR-HBR#1 was conducted at the maximum hoop stress of 145 MPa, at a 400°C maximum temperature and a 5°C/h cooling rate. On the other hand, thermal cycling was performed for tests HR-HBR#2, HR-HBR#3, and HR-HBR#4 to generate more radial hydrides. It is clear that thermal cycling increases the ratio of the radial hydride to circumferential hydrides. The internal pressure also has a significant effect on the radial hydride morphology. This report describes a procedure and experimental results of the four out-of-cell hydride reorientation tests of hydrided Zircaloy-4 cladding, which served as a guideline to prepare in-cell hydride reorientation samples with high burnup HBR fuel segments. This report also provides the Phase II CIRFT test data for the hydride reorientation irradiated samples. The variations in fatigue life are provided in terms of moment, equivalent stress, curvature, and equivalent strain for the tested SNFs. The CIRFT results appear to indicate that hydride reoriented treatment (HRT) have a negative effect on fatigue life, in addition to hydride reorientation effect. For HR4 specimen that had no pressurization procedure applied, the thermal annealing treatment alone showed a negative impact on the fatigue life compared to the HBR rod.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Progress on ATF development of SiC for LWR

Since 2011, Toshiba has been participating in a study whose objective is the commercial utilization of SiC instead of Zircaloy as LWR fuel material. During the period (Phase-1) from 2012 to 2015, feasibility studies on material design and fabrication were performed. This paper reports the principal results of a comprehensive feasibility study on SiC involving experiments and trial fabrication in terms of material properties, core and fuel design, and analytical simulation for safety analysis. The principal results are summarized as follows. First, the fabrication trials for the reduced scales of channel box and cladding have been successfully performed. Secondly, with regard to fuel rod performance analysis, hoop stress during normal operation may be a potential issue in fuel mechanical design as it is relatively high. Thirdly, with regard to safety analysis, the hydrogen generation of SiC fuel tends to decrease significantly compared with that of Zircaloy fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of RANS vs. LES simulation of fluid flow through 3 × 3 rod bundle with a simple spacer grid as a precursor to coupled fluid–structure interaction simulations

The research literature on Computational Fluid Dynamics (CFD) of coolant flow through rod bundles with spacer-grids and mixing vanes is replete, ranging from high fidelity Large Eddy Simulation (LES)/Direct Numerical Simulation (DNS) simulations to Reynolds-Averaged Navier–Stokes (RANS) modeled studies. The mixing of flow between subchannels and the pressure drop through the bundle are fundamental quantities useful for comparing and evaluating CFD methods. Less commonly observed and compared are the forces exerted onto the structure by the fluid. The present study seeks to evaluate the use of RANS simulations for predicting the structural response to fluid flow. Wall resolved RANS simulations are benchmarked against LES simulations of fluid flow at a Reynolds number of 15,000 through a 3 × 3 fuel rod bundle with a simple spacer grid. Velocity line-plots are compared showing good agreement between RANS and LES results, ascertaining that the former is capable of capturing the essential time-averaged velocity profile. Additionally, the distribution of forces on the spacer grid and fuel rods are collected as a function of time and space. The RANS methods are evaluated using the frequency and magnitude of the fluctuating forces on various portions of the structure as compared to LES. In conclusion, the power spectral density evaluation of the models reveal underprediction of force amplitude on the rod walls by RANS and also discrepancy in the prediction of high frequency spectra, especially in the immediate vicinity of spacer-grid structure, which may be attributed to the lack of random turbulence fluctuation or insufficient modeling of small-scale eddies in RANS simulation.

FIV↗

Evaluation of Neutron Radiography Reactor LEU-Core Start-Up Measurements

Benchmark models were developed to evaluate the cold-critical start-up measurements performed during the fresh core reload of the Neutron Radiography (NRAD) reactor with Low Enriched Uranium (LEU) fuel. Experiments include criticality, control-rod worth measurements, shutdown margin, and excess reactivity for four core loadings with 56, 60, 62, and 64 fuel elements. The worth of four graphite reflector block assemblies and an empty dry tube used for experiment irradiations were also measured and evaluated for the 60-fuel-element core configuration. Dominant uncertainties in the experimental k eff come from uncertainties in the manganese content and impurities in the stainless steel fuel cladding as well as the 236 U and erbium poison content in the fuel matrix. Calculations with MCNP5 and ENDF/B-VII.0 neutron nuclear data are approximately 1.4% (9σ) greater than the benchmark model eigenvalues, which is commonly seen in Monte Carlo simulations of other TRIGA reactors. Simulations of the worth measurements are within the 2σ uncertainty for most of the benchmark experiment worth values. The complete benchmark evaluation details are available in the 2014 edition of the International Handbook of Evaluated Reactor Physics Benchmark Experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Assessment of different fuel design options with SiC cladding for light water reactors

It is very important to avoid high tensile stresses in SiC if it is to be used safely as the cladding material in LWRs. To achieve this goal, three fuel design options are examined here: fuel pellets with a 10% vol central void, adding 10% vol BeO in UO{sub 2} fuel and replacing the gas gap with Lead-Bismuth Eutectic (LBE) bond. For each case, a neutronic analysis is first applied using CASMO-4E to obtain the required enrichment to achieve a fuel average burnup of 50 MWd/kgU. The fuel performance code FRAPCON, specifically FRAPCON-3.3 and FRAPCON-EP, is modified and then used to simulate the effects of steady-state irradiation in each case for typical PWR peak rod conditions. Key parameters like fuel average temperature and plenum pressure are examined for the relative performance of each approach. The results show that all three options can improve the fuel performance by lowering the fuel temperature as well as the plenum pressure. Fuel pellets with a central void design offers the most advantages since the larger void volume in the fuel rod results in the lowest plenum pressure, which is the limiting condition for safe operation of the SiC cladding. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Review of CTF’s Fuel Rod Modeling Using FRAPCON-4.0’s Centerline Temperature Predictions

Coolant Boiling in Rod Arrays–Two Fluid (COBRA-TF), or CTF1 [1], is a nuclear thermal hydraulic subchannel code used throughout academia and industry. CTF’s fuel rod modeling is originally developed for VIPRE code [2]. Its methodology is based on GAPCON [3] and FRAP [4] fuel performance codes, and material properties are included from MATPRO handbook [5]. This work focuses on review of CTF’s fuel rod modeling to address shortcomings in CTF’s temperaturepredictions. CTF is compared to FRAPCON which is U.S. NRC’s steady-state fuel performance code for light-water reactor fuel rods. FRAPCON calculates the changes in fuel rod variables and temperatures including the eects of cladding hoop strain, cladding oxidation, hydriding, fuel irradiation swelling, densification, fission gas release and rod internal gas pressure. It uses fuel, clad and gap material properties from MATPRO. Additionally, it has its own models for fission gas release, cladding corrosion and cladding hydrogen pickup. It allows finite dierence or finite element approaches for its mechanical model.In this study, FRAPCON-4.0 [6] is used as a reference fuel performance code. In comparison, Halden Reactor Data for IFA432 Rod 1 and Rod 3. CTF simulations are performed in two ways; informing CTF with gap conductance value from FRAPCON, and using CTF’s dynamic gap conductance model.First case is chosen to show temperature is predicted correctly with CTF’s models for thermal and cladding conductivities once gap conductance is provided. Latter is to review CTF’s dynamic gap conductance model. These Halden test cases are selected to be representative of cases with and without any physical contact between fuel-pellet and clad while reviewing functionality of CTF’s dynamic gap conductance model. Improving the CTF’s dynamic gap conductance model will allowprediction of fuel and cladding thermo-mechanical behavior under irradiation, and better temperature feedbacks from CTF in transient calculations.

Toptan, Aysenur↗

Thermal-Hydraulic-Mechanical Modeling and Simulation of Sodium-Potassium–Cooled MARVEL Microreactor Core

The U.S. Department of Energy's Microreactor Program, with Idaho National Laboratory's development of a nuclear microreactor applications test bed named MARVEL, aims to support R&D for the deployment of small, transportable reactors across civilian, industrial, and defense sectors. The MARVEL microreactor, an 85-kWth thermal fission reactor, incorporates TRIGA nuclear fuel and a sodium-potassium eutectic as its primary coolant, designed for safety and efficiency, with natural circulation eliminating the risk of critical heat flux conditions. The reliance on natural circulation for primary cooling means the reactor avoids using fuel spacers to minimize core pressure drop, which could disrupt the primary coolant's natural flow. However, the reactor core’s tight P/D ratio of 1.05, in the absence of fuel spacers, could pose a risk of fuel rod contact and increased peak cladding temperatures. To ensure the reactor safety, this study conducted computational modeling and simulations to investigate the reactor's thermal-hydraulic-mechanical characteristics, including the reactor core heat transfer coefficients, the potential for rod-to-rod contact, and assessed its impact on peak cladding temperature and overall reactor safety. The computational analyses of the MARVEL microreactor core revealed that the thermal deformation of fuel rods under worst-case scenario may lead to the fuel rod contact, but the peak cladding temperatures will remain significantly lower than the safety criteria, ensuring the safety operation reactor without fuel spacers under normal operating conditions.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗

Large-scale parametric modeling of spent nuclear fuel dynamics in the 30 cm package drop scenario

Packages used to transport spent nuclear fuel (SNF) are required by the U.S. Code of Federal Regulations 10 CFR 71.71 to demonstrate satisfactory performance during a drop scenario. While the CFR is meant to ensure safe package function, it does not evaluate survival of the SNF within. The U.S. Department of Energy Spent Fuel and Waste Science and Technology program is working on closing the knowledge gap related to the response of SNF to external mechanical loads, including the hypothetical 30 cm package drop scenario in the CFR. In support of this effort, LS-DYNA finite element simulations were developed by Pacific Northwest National Laboratory (PNNL) to model generic drop scenarios at both the package and fuel assembly level. The models were validated against one-third scale package and full scale fuel assembly drop test data and were exercised to predict fuel cladding strains in a narrow range of model configurations. This work describes a large-scale parametric study conducted by PNNL using the previously developed and validated PWR finite element model, with the addition of a new generic BWR assembly model. The motivation for the parametric study was to characterize the broad range of SNF responses in the 30 cm package drop scenario. This was accomplished by varying the drop orientation, fuel assembly type (17x17 PWR and 10x10 BWR), burnup, cladding temperature, spacer grid buckling load, package mass, impact limiter stiffness, and mechanical gap conditions within the basket. A MATLAB framework was developed to automate LS-DYNA model generation and execution on PNNL institutional computing resources. In total, over 2000 simulations were performed. For each simulation, the SNF response was quantified in terms of permanent grid deformation, fuel rod contact pressure, and strains within the fuel rods, guide tubes, and water rods. The results provide valuable insight into the range of responses that could be reasonably expected from SNF in the hypothetical drop scenario, as well as the sensitivity to each input parameter. The results of this parametric study are a key component of the testing and modeling strategy the Spent Fuel and Waste Science and Technology program is using to close the external loads knowledge gap.

Kadooka, Kevin↗

Application of the BISON Fuel Performance Code to the FUMEX-III Coordinated Research Project

INL recently participated in FUMEX-III, an International Atomic Energy Agency sponsored fuel modeling Coordinated Research Project. A main purpose of FUMEX-III is to compare code predictions to reliable experimental data. During the same time period, the INL initiated development of a new multidimensional (2D and 3D) multiphysics nuclear fuel performance code called BISON. Interactions with international fuel modeling researchers via FUMEX-III played a significant and important role in the BISON evolution, particularly influencing the selection of material and behavioral models which are now included in the code. BISON's ability to model integral fuel rod behavior did not mature until 2011, thus the only FUMEX-III case considered was the Riso3-GE7 experiment, which includes measurements of rod outer diameter following pellet clad mechanical interaction (PCMI) resulting from a power ramp late in fuel life. BISON comparisons to the Riso3-GE7 final rod diameter measurements are quite reasonable. The INL is very interested in participation in the next Fuel Modeling Coordinated Research Project and would like to see the project initiated as soon as possible.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Implementation of a Spacer Grid Rod Thermal-Hydraulic Reconstruction (ROTHCON) Capability into the Thermal-Hydraulic Subchannel Code CTF

The Consortium for Advanced Simulation of Light Water Reactors is developing a core simulator capability known as the Virtual Environment for Reactor Applications (VERA) to address nuclear industry challenge problems such as crud-induced power shift (CIPS). The CTF thermal-hydraulic (T/H) subchannel code provides thermal feedback in the coupled neutronics, T/H, crud chemistry simulation that VERA performs. It has been discovered that the coarse meshing approach used by CTF (in which fuel rods are discretized into four azimuthal segments) can be a source of error in predicting crud growth and boron distribution in VERA CIPS calculations. Spacer grid effects lead to complex rod-to-fluid heat transfer behavior that, when not resolved, can lead to error in the prediction of crud growth and boron deposition. A higher-fidelity computational fluid dynamics approach can be used instead of CTF, but this leads to excessive simulation times. This paper presents an approach for using high-fidelity computational fluid dynamics data to create shape functions that are used in CTF to reconstruct rod surface heat transfer behavior as a function of spacer grid geometry. The approach is demonstrated for a 5 × 5 rod bundle facility with five mixing vane grids under a range of operating conditions encountered in nominal pressurized water reactor conditions. Furthermore, it is demonstrated that the grid heat transfer maps are successful at introducing a higher-fidelity heat transfer modeling capability into CTF.

CFD-informed↗

CIRFT Testing of High-Burnup Used Nuclear Fuel Rods from the Pressurized Water Reactor and Boiling Water Reactor Environments (FY 2015 Status Report)

High burn-up spent nuclear fuel (SNF) cladding has a significant amount of microcracks and hydrides, which will reduce the stress intensity required for crack growth. The potential linking of microcracks during vibration loading could also reduce the fatigue threshold/incubation period significantly, accelerating fatigue failure. In addition to cladding damage, the microstructure of fuel pellets and the characteristics of the interfaces between fuel pellets and between fuel pellets and cladding are likely to be dramatically changed after high burn-up. These modifications can have a direct impact on the structural integrity and vibration response of SNF rods in transportation. As a result, vibration has been included as one of the mandatory testing conditions in the structural evaluation of packages used by the US Nuclear Regulation Commission (NRC) in transporting SNF (10 CFR §71.71). Prior to this program development, no current system is available to test the SNF and evaluate the performance of fuel rods during spent fuel transportation. The objective of this research is to develop a system that can appropriately test the response of high-burnup SNF rods in a simulated loading condition.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nuclear Energy Advanced Modeling and Simulation (NEAMS) Accident Tolerant Fuels High Impact Problem: Engineering Scale Models and Analysis

As part of the Department of Energy's Nuclear Energy Advanced Modeling and Simulation program, an Accident Tolerant Fuel High Impact Problem was initiated at the beginning of fiscal year 2015 to investigate the behavior of \usi\ fuel and iron-chromium-aluminum (FeCrAl) cladding under normal operating and accident reactor conditions. The High Impact Problem was created in response to the United States Department of Energy's renewed interest in accident tolerant materials after the events that occurred at the Fukushima Daiichi Nuclear Power Plant in 2011. The High Impact Problem is a multinational laboratory and university collaborative research effort between Idaho National Laboratory, Los Alamos National Laboratory, Argonne National Laboratory, and the University of Tennessee, Knoxville. This report summarizes the latest recommended material models to be used for engineering scale simulations based upon lower length scale analyses described elsewhere. Comparative analyses between traditional fuel rods (U 3 Si 2 /Zircaloy-4) and the proposed accident tolerant fuel rods (UO 2 /FeCrAl and U 3 Si 2 /Zircaloy-4) under normal operation, loss of coolant, and reactivity insertion conditions have been revisited using the latest state-of-the-art models implemented into the Bison fuel performance code. Sensitivity analyses have also been redone to take into account the latest knowledge on uncertain parameters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Time-resolved measurement of subchannel void distribution for boiling two-phase flow in 5 x 5 rod bundle at high-pressure and high-temperature

A subchannel void sensor (SCVS) was improved to acquire time-resolve boiling two-phase flow in a 5-by-5 heated rod bundle at high-pressure and high-temperature. The SCVS consists of 6-by-6 wire electrodes and 5-by-5 rod electrodes. The SCVS can acquire a time series data of local void fraction at 32 points of central subchannel region in addition to 100 points of rod surface regions between rods. The devised sensors are installed in the heated rod bundle at eight height levels to acquire two-phase flow dynamics and its development. The axial and radial power profile of the heated rod bundle are uniform, and eight pairs of sheath thermocouples are embedded on the heated rod to monitor its surface temperature distribution. The paper addresses the axial and cross-sectional distributions of void fraction at various pressure and rod bundle power conditions, which simulates an accidental condition in reactor core and in a spent fuel pool of a boiling water reactor (BWR). The experimental data are suitable to validate the computational multi-fluid dynamics (CMFD) and subchannel codes. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Development and Assessment of CTFFuel

This milestone report documents an approach that seeks to develop a standalone fuel solver to simulate steady-state and transient thermo-mechanical responses of light-water reactor fuel rods and assess its temperature predictions against analytical solutions, and a well-known and validated fuel performance code. This manuscript focuses on five major topics: (1) development of the CTFFuel, (2) discussion of the newly implemented fuel deformation models in dynamic gap conductance model of CTFFuel, (3) enabling the dynamic gap conductance model in VERA-CS, (4) verification of the solid conduction solution and comparison of the CTFFuel with respect to the workhorse code, CTF, and (5) benchmark of the thermal conductivity degradation using the burnup dependent fuel thermal conductivity models and benchmark of the fuel centerline temperature using the dynamic gap conductance model with Halden measurements and FRAPCON-4.0 simulation results. CTFFuel temperature predictions are compared to predictions from FRAPCON-4.0 for UO 2 , UO 2 +Gd 2 O 3 and MOX fuels through reactor’s life. The main motivation is to understand discrepancies between CTFFuel and FRAPCON-4.0’s temperature predictions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Measurement and modeling of the gas permeability of high burnup pressurized water reactor fuel rods

Here, the transmissibility of gas through the pellet stack of full-length pressurized water reactor (PWR) high burnup (HBU) spent nuclear fuel (SNF) rods is measured at room temperature and correlated to a permeability. Gas transmission and depressurization testing of eight high burn-up fuel rods revealed that gas communication from one end of the pellet stack to the other is unobstructed, but slow, at room temperature. Two traditional flow models, Darcy's Law and Muskat's application of Poiseuille's Law to compressible gas flow through porous media are explored. The derived permeability values for the two methods are compared and are considered in conjunction with rod cladding type and various indicators of rod operation such as burnup, High Duty Core Index (HDCI), and average fuel temperature. The derived permeability appears to be correlated to fuel temperature and maximum HDCI, but not to rod average burnup. Finally, three of the HBU rods were heat-treated to simulate dry storage vacuum drying conditions prior to the measurements and the heat-treatments may have resulted in increased permeability.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Shift Verification and Validation

This documentation outlines the verification and validation of Shift for the Consortium for Advanced Simulation of Light Water Reactors (CASL). Five main types of problems were used for validation: small criticality benchmark problems; full-core reactor benchmarks for light water reactors; fixed-source coupled neutron-photon dosimetry benchmarks; depletion/burnup benchmarks; and full-core reactor performance benchmarks. We compared Shift results to measured data and other simulated Monte Carlo radiation transport code results, and found very good agreement in a variety of comparison measures. These include prediction of critical eigenvalue, radial and axial pin power distributions, rod worth, leakage spectra, and nuclide inventories over a burn cycle. Based on this validation of Shift, we are confident in Shift to provide reference results for CASL benchmarking.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Assembly Level Modeling and Transportation Damage Prediction of Used Nuclear Fuel (UNF) Cladding

Under U.S. Nuclear Regulatory Commission (NRC) regulations, UNF must maintain its integrity in such a way that it can withstand the physical forces of handling and transportation associated with restaging the fuel and moving it to a different location such as an interim storage site, a geologic repository, or a treatment/recycling facility. Hence, understanding mechanical performance under cumulative loading stemming from normal conditions of storage (NCS), transfer from storage container to transport container if needed, and normal conditions of transport (NCT) is necessary as it establishes part of the safety basis via maintaining the fuel confining boundary (geometry), maintaining criticality safety, and is one of the critical components to the preservation of retrievability. An initial demonstration of modeling and simulation capabilities was performed as part of a collaborative effort between Pacific Northwest National Laboratory (PNNL), Sandia National Laboratory (SNL), Idaho National Laboratory (INL), Oak Ridge National Laboratory (ORNL), and the Transportation Technology Center Inc. (TTCI). This demonstration completed preliminary deterministic evaluations of moderate-to-high burnup UNF mechanical performance under NCS and NCT conditions. This paper focuses on work performed by PNNL on the assembly level modeling of a UNF assembly and fuel cladding damage predictions under NCT loads. The Finite Element (FE) model created for a 17 x 17 Pressurized Water Reactor (PWR) optimized fuel assembly (OFA) is discussed along with the communications to and from the fuel rod-level and cask-level models. Additionally, the methodology for determining cumulative damage is discussed including the 3000 mile damage prediction from a 10 second simulation. The damage results are shown for five shock and vibration broadened loading histories. It is found that predicted cladding strains were not large enough to cause structural failure, but cyclic strains roughly projected for the entire route were significant in some cases. The total damage from summation of the worst shock and vibration cases evaluated is approximately 18% of the expected fatigue limit. Therefore it is predicted that the fuel rods do not fail during NCT given the assumptions used throughout this initial demonstration.

used nuclear fuel, UNF, trasportation, damage, fue↗