Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLEXURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

MOLLER Spectrometer Magnet Design With Measured Mechanical Properties of Irradiated S2-Glass Reinforced Cyanate Ester Resin at Elevated Temperature

Here, the aim of this study was to retire the risk of maintaining the integrity of S2-glass reinforced CTD-403 (a cyanate ester resin) that is exposed to radiation and elevated temperature over the life of the measurement of a lepton–lepton electroweak reaction (MOLLER) experiment in experimental Hall A at Jefferson Lab, Newport News, VA. In this article, the shear strength and flexural modulus of irradiated S2-glass reinforced CTD-403 specimens were measured at 65 °C (the magnets are to operate at less than 65 °C) under two scenarios: vacuum and gaseous nitrogen. The testing method is the short-beam shear (SBS) test according to ASTM D2344. The specimens were exposed to neutrons and gamma rays up to 124 MGy. The results show that specimens have excellent resistance against radiation, only 23% degradation of apparent shear strength with 124 MGy at 65 °C under vacuum. At the highest dose areas of the coils, tungsten plates are used to reduce the radiation dose to the resin system. The conclusion is that S2-glass reinforced CTD-403 is well-suited for electrical insulation of MOLLER magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sensitivity of modelled passive margin stratigraphy to variations in sea level, sediment supply and subsidence

Abstract We produced a 10 Myr synthetic stratigraphic section using a forward stratigraphic model that generates marine deltaic stratigraphy over geological timescales. We recursively fit the model using a Bayesian inversion algorithm to test: (1) if it could be accurately reconstructed; (2) if the parameters used to create it could be recovered; and (3) the sensitivity of the model output to given model parameters and the attendant physical processes. The original synthetic stratigraphic section was produced with cyclical sea‐level variations of 40 and 30 m with 2.4 and 10 Myr periods respectively. Sediment was also supplied cyclically, in 2.4 and 10 Myr cycles with amplitudes of 30 and 80 tons/100 kyr, respectively, varying from a mean of 232 tons/100 kyr. Parameter values were sampled to fit the model using a Markov chain Monte Carlo algorithm, resulting in a ±5 m (1σ) variation between the experimental output and the original. Sea level varied by ±7 m (1σ) within the posterior distribution of parameters. As a result, both the 10 Myr and 2.4 Myr sea‐level cycles could be extracted from the original output. The variation in sediment supply was approximately ±38 tons/100 kyr (1σ) and, as a result, only the larger long‐term supply variations could be accurately recovered in refitting the model. The variation in thermal, flexural and total subsidence across those parameter sets is less than ±10 m (1σ). The original section experienced 150 m of total subsidence at the depocentre. Our results demonstrate the distinct and interpretable imprint of sea level and subsidence on continental margin stratigraphy can be quantified. Moreover, we conclude that sea‐level change produces a defined effect on the geometries of stratigraphic architecture, and that techniques applied for the purpose of delineating sea‐level variation from continental margin strata have a well‐founded conceptual basis.

Schmelz, William J.↗
DOE OSTI2021

Properties of SiC-Si made via binder jet 3D printing of SiC powder, carbon addition, and silicon melt infiltration

In this work, we report the physical and mechanical properties of ceramic composite materials fabricated by binder jet 3D printing (BJ3DP) with silicon carbide (SiC) powders, followed by phenolic resin infiltration and pyrolysis (IP) to generate carbon, and a final reactive silicon melt infiltration step. After two phenolic resin infiltration and pyrolysis cycles; porosity was less than 2%, Young's modulus was close to 300 GPa, and the flexural strength was 517.6 ± 24.8 MPa. However, diminishing returns were obtained after more than two phenolic resin infiltration and pyrolysis cycles as surface pores in carbon were closed upon the formation of SiC, resulting in reaction choking and residual-free carbon and porosity. The instantaneous coefficient of thermal expansion of the composite was found to be independent of the number of phenolic IP cycles and had values of between 4.2 and 5.0 ppm/°C between 300 and 100°C, whereas the thermal conductivity was found to have a weak dependence on the number of phenolic IP cycles. While the manufacturing procedures described here yielded highly dense, gas impermeable, siliconized SiC composites with properties comparable to those of bulk siliconized silicon carbide processed according to conventional techniques, BJ3DP enables the manufacture of objects with complex shape, unlike conventional techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Size effects in 3D–printed polymer–derived, zirconium diboride–reinforced ceramic composites

Preceramic polymers are of interest for use in many manufacturing techniques such as injection molding, ceramic fiber infiltration, and additive manufacturing. However, off-gassing of low molecular weight oligomers occurs when these polymers cure, potentially leading to porosity in the cured part. Here to study how porosity and strength are affected by the size of the printed part, and the presence of a high surface area nano-scale filler, polycarbosilane (PCS) microrods of varying diameter were fabricated via direct ink writing (DIW), an additive manufacturing technique, with two ink formulations containing either zirconium diboride (ZrB 2 ) alone, or ZrB 2 and fumed alumina (FA). Sets of microrods were printed in a range of sizes by using print nozzles of 450, 634, 979, 1 346, or 1 702 μm in diameter, which were thermally cured, pyrolyzed to form ceramic composite microrods, and tested in 3-pt flexure. Porosity increased with increasing diameter, while failure strength decreased. For a given nozzle size, the microrods containing FA displayed lower porosity and higher strength (up to ~500 MPa) compared to the microrods containing only ZrB 2 . Weibull strength analysis was performed on each group of microrods and shows that the addition of FA increased Weibull modulus from 4.63 ± 1.56 to 9.35 ± 0.601. In conjunction with optical microscopy, this analysis indicates two distinct flaw populations in the printed materials, porosity which arises during the curing step and cracking which arises during pyrolysis of the larger specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Machine learning control of an elliptically bent hard x-ray mirror

This article showcases the high-resolution control of an elliptically bent hard X-ray mirror optics at the Advanced Photon Source. The mirror uses a compact laminar flexure bending mechanism to achieve elliptical shapes covering a large range of focal distances. An array of capacitive sensors are used as a surface profiler for in-situ monitoring of the mirror shape. Machine learning and control techniques were used to change the mirror shape and focus the incident X-ray at predefined focal planes. The mirror surface shape error can be controlled to be within 40 nm rms with high repeatability. This technique gives the capability to focus incident X-ray beam within a range of focal distances corresponding to shape deformation range of a mirror optics. This work would be beneficial for controlling similar adaptive optics for multiple adaptive optics systems.

adaptive optics↗
DOE OSTI2025

Structural architecture of TolQ-TolR inner membrane protein complex from opportunistic pathogen Acinetobacter baumannii

Gram-negative bacteria harness the proton motive force (PMF) within their inner membrane (IM) to uphold cell envelope integrity, an indispensable aspect for both division and survival. The IM TolQ-TolR complex is the essential part of the Tol-Pal system, serving as a conduit for PMF energy transfer to the outer membrane. Here we present cryo–electron microscopy reconstructions ofAcinetobacter baumanniiTolQ in apo and TolR-bound forms at atomic resolution. The apo TolQ configuration manifests as a symmetric pentameric pore, featuring a transmembrane funnel leading toward a cytoplasmic chamber. In contrast, the TolQ-TolR complex assumes a proton nonpermeable stance, characterized by the TolQ pentamer’s flexure to accommodate the TolR dimer, where two protomers undergo a translation-based relationship. Our structure-guided analysis and simulations support the rotor-stator mechanism of action, wherein the rotation of the TolQ pentamer harmonizes with the TolR protomers’ interplay. These findings broaden our mechanistic comprehension of molecular stator units empowering critical functions within the Gram-negative bacterial cell envelope.

Science & Technology - Other Topics↗
DOE OSTI2022

Improving the damage tolerance of Si 3 N 4 by forming laminate composites with refractory metals

The objective of this research was to demonstrate that the damage tolerance of Si 3 N 4 could be significantly improved by forming laminate composites with refractory metals, providing materials that undergo graceful failure, rather than the fast-fracture mechanism exhibited by monolithic Si 3 N 4 . A damage tolerant Si 3 N 4 could be used as a ring material in an all-ceramic bearing, decreasing the chance for catastrophic failure if the ring is stressed in tension during operation. The technical approach formed a laminate composite material using alternating Si 3 N 4 -metallic layers, with both outer layers being Si 3 N 4 to take advantage of its greater wear resistance, chemical stability, and thermal stability. The metallic layers are designed to arrest any cracks in the outer layers, thus producing a toughened Si 3 N 4 and avoiding the catastrophic failure behavior exhibited by monolithic ceramics. The laminate composites were fabricated using a combination of tape-casting Si 3 N 4 and metals from slurries, as well as metal foils, followed by hot pressing at 1500°C. The metallic materials employed were chromium, titanium, and tantalum. Analysis confirmed that the interfaces were well formed, and the laminates with chromium and titanium formed intermetallic compounds more readily than the composites with tantalum. The Si 3 N 4 -Ta laminates demonstrated crack deflection and bridging behavior during failure and flexural strength of 800–900 MPa. The hardness and elastic modulus of Si 3 N 4 -Ta laminates measured by nanoindentation were similar to those reported in literature. The hardness across the interface of the Si 3 N 4 -Ta composite varied according to the composition of the interface, which displayed a profile indicative of a diffusion bond.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fibrous anisotropy and mineral gradients within the radula stylus of chiton: Controlled stiffness and damage tolerance in a flexible biological composite

Over hundreds of millions of years, organisms have evolved architected structures via precise control over hierarchically assembled components, including the integration of dissimilar materials. One such example is found in the radula system of chitons, intertidal mollusks that feed on algae growing on the rock. Their radula consists of multiple rows of ultrahard teeth, each integrated with a foldable belt-like substrate via a stiff, yet flexible stylus, which is essential for efficient rasping during the feeding process. Here, we investigate the nano and micro-scale components and architectures as well as regional mechanical properties of the stylus, and their subsequent role during the rasping of Cryptochiton stelleri. Three important factors were determined to contribute to the regio-specific stiffness of the stylus: the presence of mineral components, highly oriented chitinous fibers, and a chemically cross-linked protein matrix. All these factors are varied throughout the stylus. There is a high mineral content on the trailing edge close to the tooth and a cross-linked matrix on the leading edge, both with orientational specific oriented chitin fibers that provide force transduction to the tooth. Conversely, there is a significant lack of mineral or cross-linked matrix in the proximal end as well as a low degree of fiber orientation, resulting in a flexible region that can accommodate torsion and flexure during rasping. Understanding the graded composite structure of the stylus and applying this unique design to various engineering fields such as soft robotics, biotechnology, and the medical industry, can inspire the production of high-performance materials.

Lee, Jung-Eun↗
DOE OSTI2020

Characterization of textile-grade carbon fiber polypropylene composites

In this work, we consider low-cost carbon fiber produced with a textile-grade precursor. The objective of the study is to investigate textile-grade carbon-fiber-reinforced-polypropylene composites (TCF-PP) from compounded pellets for mechanical and thermal characterization. Four sets of pellets with 1%, 5%, 10%, and 15% reinforcement were manufactured using textile-grade carbon fiber (TCF) and polypropylene (PP) by twin-screw compounding. The addition of TCFs through gravimetric feeder directly in the extruder resulted in lower fiber content; however, side feeder has shown good potential. The pellets were further processed in extrusion compression molding to manufacture plaques. An increase in fiber loading has a negligible effect on fiber attrition as fiber length distribution variation between 1% and 15% reinforced pellets was very small. The addition of TCFs in PP showed a significant improvement in mechanical properties. The tensile strength and modulus of the composite were 26% and 161%, respectively, improved by the addition of 10 wt% TCF. Similar results were observed in the flexure test. However, the impact properties were reduced by 25.54% by the addition of 15% TCF.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of micro-sandwich structures via direct ink writing epoxy based cores

Sandwich structured (SS) composites demonstrate considerable flexural stiffness and high strength-to-weight ratios and can be tailored as functional materials. Historically they have been constrained to specific material types and geometry due to limitations in manufacturing methods. However, employing additive manufacturing (AM), specifically direct ink writing (DIW), can provide an alternative method for making SS composites with complex and controllable micro and mesostructures with multifunctionality targeted at desired mechanical, thermal, and electrical properties. DIW, an extrusion-based AM technique, uses a viscous and thixotropic ink with desired components that, once printed, is cured to obtain the final complex net shape parts. In this paper, a novel hybrid AM technique is employed to manufacture SS composite materials containing bisphenol A-based epoxy core and carbon fiber reinforced polymer (CFRP) face sheets that are fabricated via DIW and vacuum infusion process (VIP), respectfully. We demonstrate that the fabrication of these SS composites can be tailored from a thermosetting material, from which additives and/or various lattice structures can be manufactured to achieve enhanced and desirable mechanical integrity with functional properties. Surface topology and mechanical testing techniques are used to characterize the fabricated hybrid SS composites to study and assess mechanical stability. A rheo-kinetic cure model was developed for the core material to allow for additive manufacturing process requirements while ensuring complete cross-linking for the thermoset-based core material. Because of the ability to obtain relatively small core-thickness and controlled architecture, this method now allows for fabricating layered micro-sandwich structures for realizing further light-weighting in relevant applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Carbon-Storing Structural Material Based on Wastewater-Cultivated Chlorella Sorokiniana

Microalgae cultivation is a promising technology for carbon sequestration and wastewater remediation. It is economically and logistically critical to find viable applications for the large quantities of produced biomass. In current research, a structural material is developed by using nearly 100% Chlorella sorokiniana. The otherwise non-cohesive microalgae cells are first surface-activated and then compacted under a relatively high pressure. The resulting material is a dense solid, stronger than typical steel-reinforced concrete in flexural tests. The processing procedure is simple and fast, and the setup is scalable. This technique may be useful for next-generation green construction and provide a use-case for sustainable microalgae biomass.

Yi, Haozhe↗
DOE OSTI2022

Seismic monitoring of well integrity

Seismic tube waves, produced by flexure of the well boundary, pressure changes in the fluid in the well, and deformation of the material immediately surrounding the well, are particularly sensitive to variations in the state of the well. In this work, we evaluate a direct approach for generating and observing tube waves as a means of detecting well damage. While we find that it can be difficult to reliably excite observable tube waves without a very strong surface source, time-frequency techniques can be employed to increase the detectability of tube wave reflections. New technologies, particularly distributed acoustic sensing, hold great promise for evaluating well integrity by monitoring tube waves, temperature changes, and seismic noise due to well deformation and fluid leakage.

58 GEOSCIENCES↗
DOE OSTI2025

Improved Calculation of the Young’s Modulus of Rectangular Prisms from Their Resonant Frequency Overtones by Identifying Appropriate Shear Constants

Young’s modulus is an important parameter for characterizing the strength of, and wave propagation through, a given material. This study improves the estimation of Young’s modulus using the impulse excitation technique based on an experimental analysis of 19 borosilicate glass bars. Analysis of the frequency equations relating Young’s modulus to the out-of-plane and in-plane flexural resonant frequencies of rectangular prisms has been conducted for both the fundamental frequency and its overtones at higher orders of vibration. Furthermore, the Young’s moduli of three novaculite rocks with various porosities were then measured up to the seventh order of vibration to validate the optimum shear constant equation for estimating Young’s modulus. Young’s modulus was found to be nearly frequency independent for these rock samples.

Impulse excitation↗
DOE OSTI2020

Low Size, Weight, and Power Space-Based Imaging System

The proposed low-SWAP solution is a FPA focus mechanism which is composed of an actuator motor, attached to a flexure that holds the camera sensor while imaging. The mechanism, while moderately complex, allows for large changes in the focal plane while also maintaining the ability to make small adjustments to produce the best possible data. This solution does the best job at accounting for thermal gradients within the optical components that tend to degrade the image quality.

42 ENGINEERING↗
DOE OSTI2020

Fracture Strength Determination Methods for Ceramic Materials Applied to Uranium Dioxide

The Advanced Fuels Campaign is currently focusing on development of accident-tolerant fuels that possess a range of property modifications intended to improve fuel performance during accident and transient conditions as well as extend license limits to burnups beyond 62 MWd/kgU. Both of these drivers have identified understanding and mitigating fuel cracking as a key performance criterion. Small-scale cantilever beam testing has been identified as a plausible method by which to collect fracture data for UO 2 as a function of chemical and structural evolutions introduced either during fabrication or irradiation. While this method has been found to be capable of providing data that are in reasonable agreement with literature for unirradiated UO 2 , the inherently small sample volumes that can be sampled limit its ability to capture the statistical nature of mechanisms that govern the fracture of brittle ceramics. A biaxial flexure strength test was developed to be used for unirradiated UO 2 . This method is standard in the community, but no systems presently in use at national laboratories, universities, or private companies are available to be used for nuclear fuel materials. This report describes the operation and benchmarking of this system, which has been validated for a number of common oxides. Future work will extend this system to characterization of both doped UO 2 and other relevant microstructural modifications that can also be measured using small-scale cantilever beam testing. Comparison of datasets collected using both methods will allow the overall applicability of small-scale techniques to be assessed and provide confidence or bounds on their use for irradiated fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Demo 5: RapidClave Technology Demonstrations – Round II (Task 2)

The purpose of this project task was to make automotive composite part manufacturing more cost competitive for low volume production and thereby drive composite application innovation. The strategy was to incorporate low-cost preforming, snap cure resins, and RapidClave® processing to create an alternative to conventional automotive composite manufacturing based on SMC. The program used RapidClave® technology from Globe Machine Manufacturing, fast-curing (“snap cure”) epoxy resins from Hexion, and conformable/stretchable glass fiber reinforcement mats produced by Owens Corning for rapid preforming. O’Gara Armoring retrofits vehicles to meet special security needs, such as larger doors to facilitate easier entry into the vehicle. O’Gara has a variety of custom vehicles in need of custom doors that require affordable tooling to produce approximately 100 ship sets/year. The project focused on a composite door panel application provided by O’Gara that is currently made by manual chopped fiber spray-up processing. UDRI reverse-engineered the current composite door panel and created tooling for use in the RapidClave®. UDRI designed an improved composite door using MultiMat fiberglass reinforcement from Owens Corning. UDRI made snap cure resin films from Hexion resin. Finally, UDRI conducted molding trials to compare autoclave processing with RapidClave® processing. The technical goals of the project were to reduce tooling cost by 50% as compared to SMC compression molding and to reduce cycle time by 50% compared to current manual spray-up process. The approach to reduce tool costs is based on use of single sided tooling for use at 100 psi, as compared to matched metal SMC tooling. An added benefit realized from the program is that the Owens Corning mat provided more uniform thickness and improved performance. Tensile and flexural strengths and moduli were increased by at least 50%. This task also demonstrated a 75% decrease in cycle time. O’Gara is evaluating the technology demonstrated in this project for some of their current production. Additionally, there are new products O’Gara is pursuing which require higher production rates than their current products. O’Gara has identified these new products as good candidates for the RapidClave® technology. The cost advantages demonstrated by this project would then lead to significant economic development. In conclusion, this task successfully combined the RapidClave® technology from Globe with a snap cure epoxy resin film system from Hexion and preform material from Owens Corning. Further research is needed to better map the technical limits such as cycle time of these technologies. Additionally, the technology should be extended in terms of size and shape to include large parts outside of automotive applications, such as a small aircraft fuselage.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Multi-Process Tooling

Decisions made early in the automotive design process influence material selection, which in turn dictates process selection and tool design. Because of tool build time and cost of tooling, the original path is not easily altered, even if there is compelling evidence that another material or process would be beneficial. This project focused on tool design that is agile enough to allow its use in multiple processes—injection, injection compression, and extrusion-compression. This tool design allows for the manufacture of components with the most efficient process or materials, without building multiple, single-process tools. The primary purpose of the Multi-Process Tool project was to physically demonstrate that a single, well-designed tool could be used to manufacture parts with a variety of materials that require different processes. A multi-process tool would be beneficial to providing data for any changes to the process since materials and processes can be interchanged without incurring additional tool cost(s). Battery tray parts, (representative of a multi-process tool, were successfully manufactured using various types of materials, such as fiber reinforced (carbon fiber and/or glass fibers, recycled carbon fibers), amorphous (PP, TPU), semi-crystalline (PA6, PA66), and crystalline (thermoset epoxy resin) polymers. Processing of the parts was achieved by injection molding, compression molding, compression overmolding, and injection overmolding. Specimens extracted from various locations on the battery tray parts were evaluated for mechanical properties (flexure and interlaminar shear strength properties). The results show that the tool can be used to produce parts from a wide range of materials and processes with no degradation of the physical or cosmetic properties.

42 ENGINEERING↗
DOE OSTI2022

Sister Rod Destructive Examinations (FY2021) Appendix G: CRIFT Uncertainty Calculations

This document discusses the uncertainty of measurements associated with the CIRFT system and the resulting uncertainty in the acquired measurements and calculated information. The primary parameters measured during the CIRFT test include the deflection magnitude of the specimen, the load applied in bending, and the number of cycles to specimen gross failure. The associated primary calculated parameters are the bending radius/curvature and bending moment. Secondary calculated parameters include specimen stress and strain amplitudes and flexural rigidity. The uncertainty associated with the primary and secondary calculated parameters are investigated based on the known uncertainty in the measured parameters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗