Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FISSION GAS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Design, fabrication, and operation of capsules for the irradiation testing of candidate advanced space reactor fuel pins

Fuel irradiation experiments were designed, built, and operated to test uranium mononitride (UN) fuel clad in tungsten-lined T-111 and uranium dioxide fuel clad in both tungsten-lined T-111 and tungsten-lined Nb-1% Zr. A total of nine fuel pins was irradiated at average cladding temperatures ranging from 931 to 1015 C. The UN experiments, capsules UN-4 and -5, operated for 10,480 and 10,037 hr, respectively, at an average linear heat generation rate of 10 kW/ft. The UO2 experiment, capsule UN-6, operated for 8333 hr at an average linear heat generation rate of approximately 5 kW/ft. Following irradiation, the nine fuel pins were removed from their capsules, externally examined, and sent to the NASA Plum Brook Facility for more detailed postirradiation examination. During visual examination, it was discovered that the cladding of the fuel pin containing dense UN in each of capsules UN-4 and -5 had failed, exposing the UN fuel to the NaK in which the pins were submerged and permitting the release of fission gas from the failed pins. A rough analysis of the fission gas seen in samples of the gas in the fuel pin region indicated fission gas release-to-birth rates from these fuel pins in the range of .00001.

Thoms, K. R.↗

A study of transient FGR by integral LOCA tests

A study of transient fission gas release (FGR) was performed by means of two out-of-pile LOCA tests in a hot cell facility. Irradiated fuel rod segments with lengths of roughly 80 mm and burnups of 64 MWd/kgU were subjected to simulated water-cooled reactor LOCA transients in an integral LOCA test device. The segments were heated to a maximum temperature of 1000 Celsius degrees and the increase in rod inner pressure resulting from fission gas release and increased gas temperature during the transient was measured. The first release of gas occurred at temperatures close to 450 Celsius degrees, which suggests a burst release mechanism that may be linked to the onset of grain boundary fracturing. At the end of the simulated transients, gas samples were taken from the fuel rod segments for study by gas mass spectroscopy. The transient fission gas release was measured and amount to roughly 13 % of the calculated pre-test rod inventory of Kr and Xe. Isotopic ratios of the released gas indicated that transient FGR originated from the whole pellet and not only the pellet periphery. The tested segments were also studied by light-optical microscopy to determine pellet porosity, pellet crack pattern and fuel fragmentation. The extent of fine fuel fragmentation was found to be small and limited to the periphery of the fuel. The determined amount of transient fission gas release can be added to the database of fuel rod design codes to more accurately describe the LOCA cladding strains and burst temperatures in the future.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Ab Initio Molecular Dynamics Analysis of Xenon Incorporation in Uranium Dioxide

The fission process in nuclear fuel produces volatile fission product gases, such as xenon, that migrate out of the fuel and into surrounding structures. Consequently, these fission product gases may affect thermal performance and integrity of the fuel. Fission gas release models, used in modern fuel performance codes such as BISON, are currently under investigation to improve their accuracy and ability to simulate the fission gas release phenomenon and its consequences. For uranium dioxide (UO{sub 2}), the most commonly used fuel in commercial power reactors, fission gas release models are known to have significant uncertainties. In the interest of improving such models, several complex diffusional mechanisms have been examined using a variety of techniques such as Nudge Elastic Band (NEB), utilizing both Density Functional Theory (DFT) and semi-empirical inter-atomic potential functions. One proposed diffusion mechanism in UO{sub 2} is through tetra-vacancy (i.e., 2U{sub V} + 2O{sub V}) structures, which is expected to provide a suitable means for the incorporation and diffusion of xenon in the fuel crystal. In this work, a model was developed to study the incorporation of xenon in UO{sub 2} via a tetra-vacancy using ab initio molecular dynamics (AIMD). This is a first principles technique that abandons the use empirical force fields as usually is the case of classical MD analysis. Furthermore, in contrast with static transition analysis tools such as NEB, AIMD is able to capture the dynamics of a given process. The translation of xenon within a tetra-vacancy has been investigated using ab-initio molecular dynamics. The transition frequency, barrier energy, and incorporation energy were extracted from the model, demonstrating its ability to capture a variety of parameters and its potential for use in studying fission gas diffusive behavior. Future refinements to the model will seek to develop additional insight into Xe and Kr mobility and will likely involve executing more elaborate AIMD simulations to investigate this phenomenon. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mechanistic nuclear fuel performance modeling of uranium nitride

Uranium mononitride (UN) is a nuclear fuel candidate for advanced reactor designs and an alternative being considered for light water reactors due to its higher thermal conductivity and uranium density than UO 2 . As with any nuclear fuel, swelling and fission gas release are important factors for safety, while also being some of the hardest phenomena to predict with a high degree of confidence. Getting a grasp on the gas swelling behavior and release is crucial to lower the barrier for UN utilization. An accelerated swelling rate at high temperatures observed experimentally, sometimes referred to as “breakaway swelling,” further complicates the prediction of fuel performance of UN. A mechanistic model has been developed using a multiscale approach to describe the intragranular and intergranular fission gas behavior. Lower-length-scale calculations have been employed to inform models of the gas and self-diffusion behavior, resolution rate, and bubble shape. Leveraging previous work on high burnup UO 2 , two populations of intragranular bubbles are considered; small bulk bubbles and larger bubbles located along dislocations. The dislocation bubbles were found to be crucial to the overall swelling behavior, and the breakaway swelling transition was associated with the transition in the gas atom diffusion mechanism from an irradiation-induced athermal diffusion regime at lower temperatures to an intrinsic thermal equilibrium regime at higher temperatures, accelerating the growth of the dislocation bubbles. Similarly, the threshold for fission gas release was associated with the grain boundary vacancy diffusivity surpassing the gas atom diffusivity at sufficiently high temperatures, allowing the over-pressurized grain boundary bubble to grow in size and interconnect. Using thermo-mechanical models with the fission gas model, two integral fuel pin assessment cases were simulated. Finally, this work demonstrates the ability of a multiscale approach to accelerate the understanding of advanced fuel forms when experimental data is limited.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Milestone report: The simulation of radiation driven gas diffusion in UO 2 at low temperature

Below 1000 K it is thought that fission gas diffusion in nuclear fuel during irradiation occurs through atomic mixing due to radiation damage. This is an important process for nuclear reactor performance as it affects fission gas release, particularly from the periphery of the pellet where such temperatures are normal. Here we present a molecular dynamics study of Xe and Kr diffusion due to irradiation. Thermal spikes and cascades have been used to study the electronic stopping and ballistic phases of damage, respectively. Our results predict that O and Kr exhibit the greatest diffusivity and U the least, while Xe lies in between. It is concluded that the ballistic phase does not sufficiently account for the experimentally observed diffusion. Preliminary thermal spike calculations indicate that the electronic stopping phase generates greater fission gas displacement than the ballistic phase, although further calculation must be carried out to confirm this. A good description of the system by the empirical potentials is important over the very wide temperatures induced during thermal spike and damage cascade simulations. This has motivated the development of a parameter set for gas-actinide and gas-oxygen interactions that is complementary for use with a recent many-body potential set. A comprehensive set of density functional theory (DFT) calculations were used to study Xe and Kr incorporation at a number of sites in CeO 2 , ThO 2 , UO 2 and PuO 2 . These structures were used to fit a potential, which was used to generate molecular dynamics (MD) configurations incorporating Xe and Kr at 300 K, 1500 K, 3000 K and 5000 K. Subsequent matching to the forces predicted by DFT for these MD configurations was used to refine the potential set. This fitting approach ensured weighted fitting to configurations that are thermodynamically significant over a broad temperature range, while avoiding computationally expensive DFT-MD calculations. The resultant gas potentials were validated against DFT binding energies and are suitable for simulating combinations of Xe and Kr in solid solutions of CeO 2 , ThO 2 , UO 2 and PuO 2 , providing a powerful tool for the atomistic simulation of conventional nuclear reactor fuel UO 2 as well as advanced MOX fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Implementation and testing of physics-based pulverization model in BISON

This report summarizes lower length scale computational research conducted to improve the pulverization criterion for high-burnup UO 2 fuel in the BISON fuel performance code. This research was sponsored by the NEAMS program during FY22. Efforts to improve the model primarily focus on calculating the current pressure of bubbles in the high-burnup structure (HBS) region, as well as the critical bubble pressure at which pulverization occurs in the HBS. The phase-field model for predicting initial bubble pressure in the HBS was improved by implementing a more realistic model for defect production, and by coupling the phase-field model for inter-granular bubble evolution with the spatially-resolved cluster dynamics code Xolotl to simulate intra-granular fission gas evolution. An evolution equation for current bubble pressure was added to BISON, an improvement over the previous model that assumed that bubble pressure was static following HBS formation. To improve calculations of critical bubble pressure for pulverization, 3-D phase-field fracture simulations were performed, and a function for critical bubble pressure was fit—based on the simulation results—to replace the previous function, which had been determined using 2-D simulations. The impacts of these modifications to the existing pulverization assessment cases will be reported in the forthcoming engineering scale milestone on high-burnup UO 2 pulverization. A poromechanics-based approach was used to include the effect of bubble over pressurization on the stress state of the pellet at the engineering scale, and the initial strategy for integration of the pulverization criterion with pellet-scale mechanical degradation using a smeared cracking model was developed. This report also describes the initial research that was conducted to inform a forthcoming transient fission gas release (tFGR) model in BISON. Focusing on the fission gas release caused by pulverization of the outer pellet rim, a model for the amount of fission gas release was developed as a function of fuel porosity, bubble size, and fragment size. Implementation of this model in BISON and its impact of engineering-scale predictions will also be described in the aforementioned engineering-scale milestone on high-burnup UO 2 pulverization.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multiscale simulation of xenon diffusion and grain boundary segregation in UO₂

In light water reactor fuel, gaseous fission products segregate to grain boundaries, resulting in the nucleation and growth of large intergranular fission gas bubbles. The segregation rate is controlled by diffusion of fission gas atoms through the grains and interaction with the boundaries. Based on the mechanisms established from earlier density functional theory (DFT) and empirical potential calculations, diffusion models for xenon (Xe), uranium (U) vacancies and U interstitials in UO₂ have been derived for both intrinsic (no irradiation) and irradiation conditions. Segregation of Xe to grain boundaries is described by combining the bulk diffusion model with a model for the interaction between Xe atoms and three different grain boundaries in UO₂ (Σ5 tilt, Σ5 twist and a high angle random boundary), as derived from atomistic calculations. The present model does not attempt to capture nucleation or growth of fission gas bubbles at the grain boundaries. The point defect and Xe diffusion and segregation models are implemented in the MARMOT phase field code, which is used to calculate effective Xe and U diffusivities as well as to simulate Xe redistribution for a few simple microstructures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Noble gas constraints on spent fuel irradiation histories

Fission gas isotopic compositions are sensitive to a variety of reactor operating parameters that include the neutron flux, neutron fluence at different neutron energies, and operating temperature. Measurements of fission gas isotopic compositions thus have potential to constrain reactor simulations for nuclear forensics and safeguards applications. In this paper, we present Kr and Xe isotope measurements from a suite of samples obtained from locations that span the axial length a fuel pin with a well-characterized irradiation history and compare these data to spatially resolved reactor simulations. Here, we observed positive correlations between fluence sensitive isotopic ratios and burnup and between a flux sensitive ratio and power, although some discrepancies are observed between the measured data and model predictions. These differences may be due to simplifications in the model and/or inaccuracies in the cross sections. A much broader measurement to model comparison is required to better understand the discrepancies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-Irradiation Examinations of the ATF Experiments - 2020 Status

This report contains the results of post-irradiation examination (PIE) of both Accident Tolerant Fuels-1 (ATF-1) rodlets and ATF-2 rodlets irradiated in the Advanced Test Reactor (ATR). The experiment is part of the U.S. Department of Energy (DOE) Nuclear Technology Research and Development (NTRD) program’s Advanced Fuels Campaign (AFC). The ATF-1 PIE focused on the continuation of the analyses of five rodlets, one containing U 3 Si 2 fuel, two containing UN-U 3 Si 5 composites, and two with UN-U 3 Si 2 composites. The non-destructive examinations of the U 3 Si 2 rodlet showed results comparable to the previously investigated rodlets. The profilometry of the UN-U 3 Si 2 composites highlighted permanent deformation of the cladding at the pellet-pellet interface, suggesting that hourglassing of the composite pellet occurred during irradiation, causing increased localized stresses on the Zirlo cladding tube due to Pellet-Cladding Mechanical Interaction (PCMI). The UN-U 3 Si 5 rodlets, which were contained in Kanthal cladding, did not show enhanced cladding deformation at the pellet interfaces; however, it is to be noted that the initial gap of these two rodlets was larger than typical light water reactor (LWR) gaps. The larger gap might have been sufficient to accommodate the fuel swelling without having contact between the fuel and cladding, explaining the absence of PCMI. Regarding the fission products, no axial redistribution of the major gamma emitters was observed in any of the composite rodlets. Fission gas measurements on the UN-U 3 Si 5 rodlets also has been performed. The estimated fission gas release, based on the calculated fission product inventory, remains limited, with a higher fission gas release for the rodlet that experienced a higher power.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

TEM characterization of irradiated U-7Mo/Mg dispersion fuel

This paper presents the results of transmission electron microscopy (TEM) characterization on neutron-irradiated samples taken from the low-flux and high-flux sides of the same fuel plate with U-7Mo fuel particles dispersed in Mg matrix with aluminum alloy Al6061 as cladding material that was irradiated edge-on to the core in the Advanced Test Reactor. The corresponding local fission density and fission rate of the fuel particles and the average fuel-plate centerline temperature for the low-flux and high-flux samples are estimated to be 3.7 × 10 21 f/cm 3 , 7.4 × 10 14 f/cm 3 /s and 123 °C, and 5.5 × 10 21 f/cm3, 11.0 × 10 14 f/cm 3 /s and 158 °C, respectively. Complex interaction layers developed at the Al-Mg interface, consisting of Al 3 Mg 2 and Al 12 Mg 17 along with precipitates of MgO, Mg 2 Si and FeAl 5.3 . No interaction between Mg matrix and U-Mo fuel particle was identified. For the U-Mo fuel particles, at low fission density, small elongated bubbles wrapped around the clean areas with a fission gas bubble superlattice, which suggests that bubble coalescence is an important mechanism for converting the fission gas bubble superlattice to large bubbles. At high fission density, no bubbles or porosity were observed in the Mg matrix, and pockets of residual fission gas bubble superlattice were observed in the U-Mo fuel particle interior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

JASMINE: a fuel rod thermal-mechanical performance's code

JASMINE, which is developed by China General Nuclear Power Corporation (CGNPC), is a code for calculating thermal-mechanical response of PWR fuel rods. The code models many physical phenomena, including heat conduction through the fuel and cladding to the coolant, cladding elastic and plastic deformation, fuel elastic deformation, fuel swelling and densification,fuel-cladding mechanical interaction, fission gas release from the fuel, rod internal pressure, cladding oxidation and hydriding. Just as most fuel rod codes, JASMINE, which is a quasi-two dimensional code, includes a thermal module, a mechanical module, a fission gas release (FGR) module, and an internal pressure module. For thermal module, the time dependent thermal conduction equation of axisymmetric cylindrical geometry, Halden's fuel thermal conductivity, thermal conductivity integration method and multi-dimension Newton-Raphson procedure are used; for the mechanical module, generalized plane strain hypothesis, cladding-fuel axial lockup model, cladding thermal stress and transfer matrix method are applied; for fission gas release module, the time dependent diffusion equation for a spherical grain, Speight-Turnbull grain surface boundary condition, and Forsberg-Massih's method are used; for the internal pressure module, the ideal gas state equation is used. The code, which is on validation stage, will be used for fuel rod design of nuclear power plants in China in a near future. So far, the preliminary validation process for pellet centerline temperature and fission gas release, which is based on fuel rod test data in FUMEX-III project, has finished. According to the validation results, JASMINE has the ability to reasonably predicts fuel behavior and performance in-pile. JASMINE has good prediction in fuel temperature, and good prediction on FGR as a whole. However, for FGR in the range 1% to 15%, JASMINE over-predicts FGR; for other range, JASMINE underestimates FGR. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The use of U3Si2/Al dispersion fuel for high power research reactors

In order to investigate the irradiation performance of U3Si2/Al dispersion fuel at relatively aggressive reactor conditions, compared to how this fuel is typically used in a research or test reactor, post irradiation examination was performed on two fuel plates that were irradiated at ~270 W/cm2 average surface heat flux and to a maximum local burnup greater than 8 × 1021 fissions/cm3 in the Advanced Test Reactor as part of the RERTR-8 experiment. As part of the non-destructive examinations that were performed on both fuel plates, detailed thickness measurements using a high-fidelity measurement bench were performed on one fuel plate and a segment of the second fuel plate. This paper provides the first reported results of such high-resolution thickness measurements for U3Si2/Al dispersion fuel plates, containing primarily the U3Si2 fuel phase, irradiated at such power levels to high burnup. For destructive examination using optical metallography, samples were generated from both irradiated plates. Localized regions of high swelling (characteristic of internal blistering) were observed on the surface of both fuel plates, suggesting that the performance limits had been reached for each plate. Destructive examinations showed that the fuel particles that are primarily U3Si2, which become amorphous during irradiation, in both plates contained relatively large fission gas bubbles with evidence of fission gas bubble interconnection.

Wachs, Daniel M.↗

Advanced Multiscale Microscopy Characterization of High Burnup LWR UO 2 Before and After LOCA Testing

Previous microscopy work within the campaign has observed increased porosity coupled with subgrain formation in the mid-radial region of the fuel. However, examinations of high burnup fuel taken from multiple reactors with different operating conditions have shown that this structure can move radially inward depending on the fuel operating conditions. It is currently theorized that inter- and intragranular fission gas bubble nucleation is precursory to the grain subdivision observed in the mid-radial and central regions of the fuel. Characterization of samples after loss-of-coolant accident (LOCA) testing has revealed that these restructured regions with a high density of bubbles and subgrains pulverize during the transient test. It appears that the increase in fission gas bubbles coupled with grain subdivision renders the fuel mechanically weaker during a LOCA transient and thus susceptible to fuel fragmentation relocation and dispersal (FFRD). Work this past fiscal year has prioritized understanding this behavior by using advanced microscopy to investigate fission gas behavior in the as-irradiated and post-LOCA state. Additional work has been performed to verify the theory described above by analyzing multiple post-LOCA optical micrographs and comparing that to as-irradiated microstructural data. This document reports progress in the post-irradiation characterization of high burnup nuclear fuel with emphasis on the restructured fuel regions, particularly how microstructural features influence FFRD and fission gas release behavior in LOCA conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-5/6/7 Final Release-to-Birth Ratio Data Analysis

AGR-5/6/7 is the last of a series of Advanced Gas Reactor (AGR) experiments conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) in support of development and qualification of tristructural isotropic (TRISO) low-enriched fuel for use in the high-temperature gas cooled reactor (HTGR). AGR configuration and irradiation conditions are based on prismatic HTGR technology that is distinguished primarily through the use of helium coolant, a low-power-density ceramic core capable of withstanding very high temperatures, and TRISO-coated particle fuel. The AGR tests provide valuable irradiation-performance data to support fuel process development, qualify fuel for normal operation and accident conditions, and support development and validation of fuel performance and fission-product (FP) transport models and codes. Each AGR test consists of multiple independently controlled and monitored capsules containing fuel compacts placed in a graphite cylinder shrouded by a steel shell. Release-to-birth ratios (R/B) for fission-gas isotopes released from each capsule are calculated from release rates, measured by germanium detectors in the Fission Product Monitoring System (FPMS) installed downstream from each capsule, and birth rates calculated using numerical models of FG generation. The R/Bs are a critical measure of the ability of the fuel kernel, the particle coating layers, and the compact matrix to retain fission-gas atoms, preventing their release into the sweep-gas flow, and the impact of initially defective particles and/or particle-coating failures that occur during irradiation. For fission-gas isotopes, particle failure is defined as failure of all coating layers, allowing gaseous fission atoms to escape from a particle. During the first five cycles (162B ? 165A), R/Bs were stable in the 10-8?10-6 range, and no in-pile particle failures were observed, based on the gross gamma counts. The maximum R/B value of around 2 ? 10-6 for Kr-85m resulted from the presence of as-fabricated exposed kernels (based on the high exposed kernel fraction), the dispersed uranium, and high fuel particle temperatures in Capsule 1. Comparison of capsule-measured R/Bs from these early cycles to predictions using the previously developed AGR R/B model demonstrated FG release from the AGR-5/6/7 TRISO fuel was comparable to that of previous experiments. In addition, the Kr-85m R/B per-exposed-kernel values are comparable to R/B values obtained in AGR-3/4 irradiation experiment and four irradiation experiments performed during 1980s: (1) HRB-17/18, (2) COMEDIE-BD1, (3) HFR B1, and (4) HRB-21. In contrast, all measured R/B values are lower than predictions by the commonly used Richards and German models, which are intentionally conservative. A large number of in-pile particle failures occurred in Capsule 1 by the end of Cycle 166A. During the final four cycles (166A ? 168A), apparent damage to the Capsule 1 gas line appeared to cause FG leakage from that capsule into the other four capsules, resulting in an increase in fission gas (FG) detected in the effluent for all capsules. Isolation of the Capsule 1 gas line during the last three cycles also prevented measurement of its FG release. Thus, R/Bs in all capsules after Cycle 166A are highly uncertain because of undefined amount of leakage from Capsule 1, especially for long-lived isotopes. A few hundred in-pile particle failures were estimated for Capsule 1 before the end of Cycle 166A, but the total number of failures is unknown due to the lack of FG release data in the later cycles. Based primarily on evidence from the gross gamma counts during Cycle 168A, approximately 15 particles failed in Capsule 3 and four particles failed in Capsule 2. In-pile failures in Capsule 3 were anticipated because this capsule was designed to operate beyond the HTGR normal operating temperature range. In contrast, no in-pile failures were identified in the top two capsules (4 and 5) based on the absence of the typical spikes in gross gamma counts and low failure estimates using the AGR model, developed in INL/EXT-14-32970, for R/B of the short-lived isotopes (Kr-89 and Xe-137) with minimal leakage from Capsule 1.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transmission Electron Microscopy Characterization of Irradiated U-7Mo/Al-2Si Dispersion Fuel

The plate-type dispersion fuels, with the atomized U(Mo) fuel particles dispersed in the Al or Al alloy matrix, are being developed for use in research and test reactors worldwide. It is found that the irradiation performance of a plate-type dispersion fuel depends on the radiation stability of the various phases in a fuel plate. Transmission electron microscopy was performed on a sample (peak fuel mid-plane temperature approximately 109 degrees C and fission density approximately 4.5 x 10 27 fm-3) taken from an irradiated U–7Mo dispersion fuel plate with Al–2Si alloy matrix to investigate the role of Si addition in the matrix on the radiation stability of the phase(s) in the U–7Mo fuel/matrix interaction layer. A similar interaction layer that forms in irradiated U–7Mo dispersion fuels with pure Al matrix has been found to exhibit poor irradiation stability, likely as a result of poor fission gas retention. The interaction layer for both U–7Mo/Al–2Si and U–7Mo/Al fuels is observed to be amorphous. However, unlike the latter, the amorphous layer for the former was found to effectively retain fission gases in areas with high Si concentration. When the Si concentration becomes relatively low, the fission gas bubbles agglomerate into fewer large pores. Within the U–7Mo fuel particles, a bubble superlattice ordered as fcc structure and oriented parallel to the bcc metal lattice was observed where the average bubble size and the superlattice constant are approximately 3.5 nm and approximately 7.5 nm, respectively. The estimated fission gas inventory in the bubble superlattice correlates well with the fission density in the fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Gaseous swelling of U 3 Si 2 during steady-state LWR operation: A rate theory investigation

Rate theory simulations of fission gas behavior in U 3 Si 2 are reported for light water reactor (LWR) steady-state operation scenarios. We developed a model of U 3 Si 2 and implemented into the GRASS-SST code based on available research reactor post-irradiation examination (PIE) data, and density functional theory (DFT) calculations of key material properties. Simplified peripheral models were also introduced to capture the fuel-cladding interaction. The simulations identified three regimes of U 3 Si 2 swelling behavior between 390 K and 1190 K. Under typical steady-state LWR operating conditions where U 3 Si 2 temperature is expected to be below 1000 K, intragranular bubbles are dominant and fission gas is retained in those bubbles. The consequent gaseous swelling is low and associated degradation in the fuel thermal conductivity is also limited. Those predictions of U 3 Si 2 performance during steady-state operations in LWRs suggest that this fuel material is an appropriate LWR candidate fuel material. Fission gas behavior models established based on this work are being coupled to the thermo-mechanical simulation of the fuel behavior using the BISON fuel performance multi-dimensional finite element code.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

In-situ ion irradiation of fission products in a spent UO 2 fuel

This study investigates the behavior of fission gas bubbles and five metal precipitates (5MPs) (Mo, Ru, Rh, Tc, Pd) in spent uranium dioxide (UO 2 ) fuel under various ion irradiation doses, temperatures, and flux conditions. Utilizing in-situ ion irradiation and advanced transmission electron microscopy, we analyzed the evolution of fission gas bubbles and 5MPs in UO 2 samples from the Belgium Reactor 3 (BR-3). Our findings reveal significant shrinkage of fission gas bubbles and 5MPs with increasing irradiation dose, accompanied by a decrease in pair density. We demonstrate that ion irradiation induces a homogeneous re-solution process where individual atoms are ejected from bubbles and precipitates, leading to their dissolution and subsequent re-precipitation in the matrix. In conclusion, this study provides critical insights into the dynamic behavior of fission products under irradiation, facilitating the development of predictive models and contributing to the optimization of nuclear fuel performance and safety.

Fission products↗

Ab-initio informed cluster dynamics simulation of self- and Xe diffusivity in uranium mononitride under irradiation

Uranium mononitride (UN) is one of the ceramic nuclear fuel alternatives to oxide fuels considered for light water reactor and advanced reactor designs, as it presents significant advantages such as high uranium density (better economics) and high thermal conductivity and melting point (increased safety). Self- and fission gas diffusivities need to be better understood, given that they influence key fuel performance phenomena like swelling and fission gas release. Recently, radiation enhanced diffusivity was investigated in UN by means of cluster dynamics simulations relying on empirical potential-based parameterizations, the reliability of which highly depends on the interatomic potential accuracy. Here, in this work, we refine this approach by determining, using ab-initio calculations, the properties of defect clusters containing vacancies, self-interstitials and Xe impurities. We also consider larger clusters than previous studies. The obtained dataset (formation enthalpies, entropies, and migration barriers) is used to parameterize a cluster dynamics model of mobile clusters, and to calculate the defect cluster concentrations under irradiation. This gives us access to the radiation enhanced self- and fission gas diffusivities. Although the resulting diffusivities are close to the values reported in the literature, we find important qualitative differences in the diffusion mechanisms. Capturing the correct mechanisms is crucial to properly describe the chemistry and fission rate dependence of the model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗